Abstract: In this paper, Zinc Oxide (ZnO) thin films are deposited on glass substrate by sol-gel method. The ZnO thin films with well defined orientation were acquired by spin coating of zinc acetate dehydrate monoethanolamine (MEA), de-ionized water and isopropanol alcohol. These films were pre-heated at 275°C for 10 min and then annealed at 350°C, 450°C and 550°C for 80 min. The effect of annealing temperature and different thickness on structure and surface morphology of the thin films were verified by Atomic Force Microscopy (AFM). It was found that there was a significant effect of annealing temperature on the structural parameters of the films such as roughness exponent, fractal dimension and interface width. Thin films also were characterizied by X-ray Diffractometery (XRD) method. XRD analysis revealed that the annealed ZnO thin films consist of single phase ZnO with wurtzite structure and show the c-axis grain orientation. Increasing annealing temperature increased the crystallite size and the c-axis orientation of the film after 450°C. Also In this study, ZnO thin films in different thickness have been prepared by sol-gel method on the glass substrate at room temperature. The thicknesses of films are 100, 150 and 250 nm. Using fractal analysis, morphological characteristics of surface films thickness in amorphous state were investigated. The results show that with increasing thickness, surface roughness (RMS) and lateral correlation length (ξ) are decreased. Also, the roughness exponent (α) and growth exponent (β) were determined to be 0.74±0.02 and 0.11±0.02, respectively.
Abstract: In a wind power generator using doubly fed induction
generator (DFIG), the three-phase pulse width modulation (PWM)
voltage source converter (VSC) is used as grid side converter (GSC)
and rotor side converter (RSC). The standard linear control laws
proposed for GSC provides not only instablity against comparatively
large-signal disturbances, but also the problem of stability due to
uncertainty of load and variations in parameters. In this paper, a
nonlinear controller is designed for grid side converter (GSC) of a
DFIG for wind power application. The nonlinear controller is
designed based on the input-output feedback linearization control
method. The resulting closed-loop system ensures a sufficient
stability region, make robust to variations in circuit parameters and
also exhibits good transient response. Computer simulations and
experimental results are presented to confirm the effectiveness of the
proposed control strategy.
Abstract: Multicast Network Technology has pervaded our
lives-a few examples of the Networking Techniques and also for the
improvement of various routing devices we use. As we know the
Multicast Data is a technology offers many applications to the user
such as high speed voice, high speed data services, which is presently
dominated by the Normal networking and the cable system and
digital subscriber line (DSL) technologies. Advantages of Multi cast
Broadcast such as over other routing techniques. Usually QoS
(Quality of Service) Guarantees are required in most of Multicast
applications. The bandwidth-delay constrained optimization and we
use a multi objective model and routing approach based on genetic
algorithm that optimizes multiple QoS parameters simultaneously.
The proposed approach is non-dominated routes and the performance
with high efficiency of GA. Its betterment and high optimization has
been verified. We have also introduced and correlate the result of
multicast GA with the Broadband wireless to minimize the delay in
the path.
Abstract: The design of a gravity dam is performed through an
interactive process involving a preliminary layout of the structure
followed by a stability and stress analysis. This study presents a
method to define the optimal top width of gravity dam with genetic
algorithm. To solve the optimization task (minimize the cost of the
dam), an optimization routine based on genetic algorithms (GAs) was
implemented into an Excel spreadsheet. It was found to perform well
and GA parameters were optimized in a parametric study. Using the
parameters found in the parametric study, the top width of gravity
dam optimization was performed and compared to a gradient-based
optimization method (classic method). The accuracy of the results
was within close proximity. In optimum dam cross section, the ratio
of is dam base to dam height is almost equal to 0.85, and ratio of dam
top width to dam height is almost equal to 0.13. The computerized
methodology may provide the help for computation of the optimal
top width for a wide range of height of a gravity dam.
Abstract: For complete support of Quality of Service, it is better that environment itself predicts resource requirements of a job by using special methods in the Grid computing. The exact and correct prediction causes exact matching of required resources with available resources. After the execution of each job, the used resources will be saved in the active database named "History". At first some of the attributes will be exploit from the main job and according to a defined similarity algorithm the most similar executed job will be exploited from "History" using statistic terms such as linear regression or average, resource requirements will be predicted. The new idea in this research is based on active database and centralized history maintenance. Implementation and testing of the proposed architecture results in accuracy percentage of 96.68% to predict CPU usage of jobs and 91.29% of memory usage and 89.80% of the band width usage.
Abstract: This paper will focus on modeling, analysis and simulation of a 42V/14V dc/dc converter based architecture. This architecture is considered to be technically a viable solution for automotive dual-voltage power system for passenger car in the near further. An interleaved dc/dc converter system is chosen for the automotive converter topology due to its advantages regarding filter reduction, dynamic response, and power management. Presented herein, is a model based on one kilowatt interleaved six-phase buck converter designed to operate in a Discontinuous Conduction Mode (DCM). The control strategy of the converter is based on a voltagemode- controlled Pulse Width Modulation (PWM) with a Proportional-Integral-Derivative (PID). The effectiveness of the interleaved step-down converter is verified through simulation results using control-oriented simulator, MatLab/Simulink.
Abstract: Recently, there have been considerable efforts towards the convergence between P2P and Grid computing in order to reach a solution that takes the best of both worlds by exploiting the advantages that each offers. Augmenting the peer-to-peer model to the services of the Grid promises to eliminate bottlenecks and ensure greater scalability, availability, and fault-tolerance. The Grid Information Service (GIS) directly influences quality of service for grid platforms. Most of the proposed solutions for decentralizing the GIS are based on completely flat overlays. The main contributions for this paper are: the investigation of a novel resource discovery framework for Grid implementations based on a hierarchy of structured peer-to-peer overlay networks, and introducing a discovery algorithm utilizing the proposed framework. Validation of the framework-s performance is done via simulation. Experimental results show that the proposed organization has the advantage of being scalable while providing fault-isolation, effective bandwidth utilization, and hierarchical access control. In addition, it will lead to a reliable, guaranteed sub-linear search which returns results within a bounded interval of time and with a smaller amount of generated traffic within each domain.
Abstract: This study is to evaluate the behavior of integral and
segmental specimens through static and cyclic tests. Integral
specimens were made with the same size to be compared with
segmental specimens that were made by connected precast members.
To evaluate its bending performance and serviceability, 1 integral and
3 segmental specimens were tested under static load. And 1 integral
and 2 segmental specimens were tested under cyclic load, respectively.
Different load ranges were considered in the cyclic tests to evaluate the
safety and serviceability. The test results showed that under static
loading, segmental specimens had about 94% of the integral
specimen's maximum moment, averagely. Under cyclic loading, the
segmental specimens showed that had enough safety in the range of
higher than service load and enough serviceability. In conclusion, the
maximum crack width (0.16mm) satisfied the allowable crack width
(0.30mm) in the range of service load.
Abstract: We present a simulation and realization of a battery
charge regulator (BCR) in microsatellite earth observation. The tests
were performed on battery pack 12volt, capacity 24Ah and the solar array open circuit voltage of 100 volt and optimum power of about
250 watt. The battery charge is made by solar module. The principle is to adapt the output voltage of the solar module to the battery by
using the technique of pulse width modulation (PWM). Among the different techniques of charge battery, we opted for the technique of
the controller ON/OFF is a standard technique and simple, it-s easy to
be board executed validation will be made by simulation "Proteus Isis
Professional software ". The circuit and the program of this prototype
are based on the PIC16F877 microcontroller, a serial interface connecting a PC is also realized, to view and save data and graphics
in real time, for visualization of data and graphs we develop an interface tool “visual basic.net (VB)--.
Abstract: Bendability is constrained by maximum top roller
load imparting capacity of the machine. Maximum load is
encountered during the edge pre-bending stage of roller bending.
Capacity of 3-roller plate bending machine is specified by
maximum thickness and minimum shell diameter combinations that
can be pre-bend for given plate material of maximum width.
Commercially available plate width or width of the plate that can be
accommodated on machine decides the maximum rolling width.
Original equipment manufacturers (OEM) provide the machine
capacity chart based on reference material considering perfectly
plastic material model. Reported work shows the bendability analysis
of heavy duty 3-roller plate bending machine. The input variables for
the industry are plate thickness, shell diameter and material property
parameters, as it is fixed by the design. Analytical models of
equivalent thickness, equivalent width and maximum width based on
power law material model were derived to study the bendability.
Equation of maximum width provides bendability for designed
configuration i.e. material property, shell diameter and thickness
combinations within the machine limitations. Equivalent thicknesses
based on perfectly plastic and power law material model were
compared for four different materials grades of C-Mn steel in order
to predict the bend-ability. Effect of top roller offset on the
bendability at maximum top roller load imparting capacity is
reported.
Abstract: In this paper, we propose a novel frequency offset
estimation scheme for orthogonal frequency division multiplexing
(OFDM) systems. By correlating the OFDM signals within the coherence
phase bandwidth and employing a threshold in the frequency
offset estimation process, the proposed scheme is not only robust to
the timing offset but also has a reduced complexity compared with
that of the conventional scheme. Moreover, a timing offset estimation
scheme is also proposed as the next stage of the proposed frequency
offset estimation. Numerical results show that the proposed scheme
can estimate frequency offset with lower computational complexity
and does not require additional memory while maintaining the same
level of estimation performance.
Abstract: Numerical study of a plane jet occurring in a vertical
heated channel is carried out. The aim is to explore the influence of
the forced flow, issued from a flat nozzle located in the entry section
of a channel, on the up-going fluid along the channel walls. The
Reynolds number based on the nozzle width and the jet velocity
ranges between 3 103 and 2.104; whereas, the Grashof number based
on the channel length and the wall temperature difference is 2.57
1010. Computations are established for a symmetrically heated
channel and various nozzle positions. The system of governing
equations is solved with a finite volumes method. The obtained
results show that the jet-wall interactions activate the heat transfer,
the position variation modifies the heat transfer especially for low
Reynolds numbers: the heat transfer is enhanced for the adjacent
wall; however it is decreased for the opposite one. The numerical
velocity and temperature fields are post-processed to compute the
quantities of engineering interest such as the induced mass flow rate,
and the Nusselt number along the plates.
Abstract: The more recent satellite projects/programs makes
extensive usage of real – time embedded systems. 16 bit processors
which meet the Mil-Std-1750 standard architecture have been used in
on-board systems. Most of the Space Applications have been written
in ADA. From a futuristic point of view, 32 bit/ 64 bit processors are
needed in the area of spacecraft computing and therefore an effort is
desirable in the study and survey of 64 bit architectures for space
applications. This will also result in significant technology
development in terms of VLSI and software tools for ADA (as the
legacy code is in ADA).
There are several basic requirements for a special processor for
this purpose. They include Radiation Hardened (RadHard) devices,
very low power dissipation, compatibility with existing operational
systems, scalable architectures for higher computational needs,
reliability, higher memory and I/O bandwidth, predictability, realtime
operating system and manufacturability of such processors.
Further on, these may include selection of FPGA devices, selection
of EDA tool chains, design flow, partitioning of the design, pin
count, performance evaluation, timing analysis etc.
This project deals with a brief study of 32 and 64 bit processors
readily available in the market and designing/ fabricating a 64 bit
RISC processor named RISC MicroProcessor with added
functionalities of an extended double precision floating point unit
and a 32 bit signal processing unit acting as co-processors. In this
paper, we emphasize the ease and importance of using Open Core
(OpenSparc T1 Verilog RTL) and Open “Source" EDA tools such as
Icarus to develop FPGA based prototypes quickly. Commercial tools
such as Xilinx ISE for Synthesis are also used when appropriate.
Abstract: A high energy dual-wavelength extracavity KTA
optical parametric oscillator (OPO) with excellent stability and beam
quality, which is pumped by a Q-switched single-longitudinal-mode
Nd:YAG laser, has been demonstrated based on a type II noncritical
phase matching (NCPM) KTA crystal. The maximum pulse energy of
10.2 mJ with the output stability of better than 4.1% rms at 3.467 μm is
obtained at the repetition rate of 10 Hz and pulse width of 2 ns, and the
11.9 mJ of 1.535 μm radiation is obtained simultaneously. This
extracavity NCPM KTA OPO is very useful when high energy, high
beam quality and smooth time domain are needed.
Abstract: The data measurement of mean velocity has been
taken for the wake of single circular cylinder with three different diameters for two different velocities. The effects of change in
diameter and in velocity are studied in self-similar coordinate system.
The spatial variations of velocity defect and that of the half-width
have been investigated. The results are compared with those
published by H.Schlichting. In the normalized coordinates, it is also observed that all cases except for the first station are self-similar. By attention to self-similarity profiles of mean velocity, it is observed for all the cases at the each station curves tend to zero at a same point.
Abstract: We report the size dependence of 1D superconductivity in ultrathin (10-130 nm) nanowires produced by coating suspended carbon nanotubes with a superconducting NbN thin film. The resistance-temperature characteristic curves for samples with ≧25 nm wire width show the superconducting transition. On the other hand, for the samples with 10-nm width, the superconducting transition is not exhibited owing to the quantum size effect. The differential resistance vs. current density characteristic curves show some peak, indicating that Josephson junctions are formed in nanowires. The presence of the Josephson junctions is well explained by the measurement of the magnetic field dependence of the critical current. These understanding allow for the further expansion of the potential application of NbN, which is utilized for single photon detectors and so on.
Abstract: This paper presents a novel sinusoidal modulation
scheme that features least correlated noise and high linearity. The
modulation circuit, which is composed of a quantizer, a resonator, and
a comparator, is capable of eliminating correlated modulation noise
while doing modulation. The proposed modulation scheme combined
with the linear quadratic optimal control is applied to a single-phase
voltage source inverter and validated with the experiment results. The
experiments show that the inverter supplies stable 60Hz 110V AC
power with a total harmonic distortion of less than 1%, under the DC
input variation from 190 V to 300 V and the output power variation
from 0 to 600 W.
Abstract: A lot of computer-based methods have been developed
to assess the evacuation capability (EC) of high-rise buildings.
Because softwares are time-consuming and not proper for on scene
applications, we adopted two methods, fuzzy analytic hierarchy
process (FAHP) and technique for order preference by similarity to an
ideal solution (TOPSIS), for EC assessment of a high-rise building in
Jinan. The EC scores obtained with the two methods and the
evacuation time acquired with Pathfinder 2009 for floors 47-60 of the
building were compared with each other. The results show that FAHP
performs better than TOPSIS for EC assessment of high-rise buildings,
especially in the aspect of dealing with the effect of occupant type and
distance to exit on EC, tackling complex problem with multi-level
structure of criteria, and requiring less amount of computation.
However, both FAHP and TOPSIS failed to appropriately handle the
situation where the exit width changes while occupants are few.
Abstract: Internet is without any doubt the fastest and effective mean of communication making it possible to reach a great number of people in the world. It draws its base from exchange points. Indeed exchange points are used to inter-connect various Internet suppliers and operators in order to allow them to exchange traffic and it is with these interconnections that Internet made its great strides. They thus make it possible to limit the traffic delivered via the operators of transits. This limitation allows a significant improvement of the quality of service, a reduction in the latency time just as a reduction of the cost of connection for the final subscriber. Through this article we will show how the installation of an IXP allows an improvement and a diversification of the services just as a reduction of the Internet connection costs.
Abstract: A stiffened laminated composite panel (1 m length ×
0.5m width) was optimized for minimum weight and deflection under
several constraints using genetic algorithm. Here, a significant study
on the performance of a penalty function with two kinds of static and
dynamic penalty factors was conducted. The results have shown that
linear dynamic penalty factors are more effective than the static ones.
Also, a specially combined linear-exponential function has shown to
perform more effective than the previously mentioned penalty
functions. This was then resulted in the less sensitivity of the GA to
the amount of penalty factor.