Abstract: The LHP is a two-phase device with extremely high
effective thermal conductivity that utilizes the thermodynamic
pressure difference to circulate a cooling fluid. A thermodynamics
analytical model is developed to explore different parameters effects
on a Loop Heat Pipe (LHP).. The effects of pipe length, pipe
diameter, condenser temperature, and heat load are reported. As pipe
length increases and/or pipe diameter decreases, a higher temperature
is expected in the evaporator.
Abstract: The separation efficiency of a hydrocyclone has
extensively been considered on the rigid particle assumption. A
collection of experimental studies have demonstrated their
discrepancies from the modeling and simulation results. These
discrepancies caused by the actual particle elasticity have generally
led to a larger amount of energy consumption in the separation
process. In this paper, the influence of particle elasticity on the
separation efficiency of a hydrocyclone system was investigated
through the Finite Element (FE) simulations using crude oil droplets
as the elastic particles. A Reitema-s design hydrocyclone with a
diameter of 8 mm was employed to investigate the separation
mechanism of the crude oil droplets from water. The cut-size
diameter eter of the crude oil was 10 - Ðçm in order to fit with the
operating range of the adopted hydrocylone model. Typical
parameters influencing the performance of hydrocyclone were varied
with the feed pressure in the range of 0.3 - 0.6 MPa and feed
concentration between 0.05 – 0.1 w%. In the simulation, the Finite
Element scheme was applied to investigate the particle-flow
interaction occurred in the crude oil system during the process. The
interaction of a single oil droplet at the size of 10 - Ðçm to the flow
field was observed. The feed concentration fell in the dilute flow
regime so the particle-particle interaction was ignored in the study.
The results exhibited the higher power requirement for the separation
of the elastic particulate system when compared with the rigid
particulate system.
Abstract: Development of a Robust Supply Chain for Dynamic
Operating Environment as we move further into the twenty first
century, organisations are under increasing pressure to deliver a high
product variation at a reasonable cost without compromise in quality.
In a number of cases this will take the form of a customised or high
variety low volume manufacturing system that requires prudent
management of resources, among a number of functions, to achieve
competitive advantage. Purchasing and Supply Chain management is
one of such function and due to the substantial interaction with
external elements needs to be strategically managed. This requires a
number of primary and supporting tools that will enable the
appropriate decisions to be made rapidly. This capability is
especially vital in a dynamic environment as it provides a pivotal role
in increasing the profit margin of the product. The management of
this function can be challenging by itself and even more for Small
and Medium Enterprises (SMEs) due to the limited resources and
expertise available at their disposal.
This paper discusses the development of tools and concepts
towards effectively managing the purchasing and supply chain
function. The developed tools and concepts will provide a cost
effective way of managing this function within SMEs. The paper
further shows the use of these tools within Contechs, a manufacturer
of luxury boat interiors, and the associated benefits achieved as a
result of this implementation. Finally a generic framework towards
use in such environments is presented.
Abstract: A solar powered air heating system using one ended evacuated tubes is experimentally investigated. A solar air heater containing forty evacuated tubes is used for heating purpose. The collector surface area is about 4.44 m2. The length and outer diameters of the outer glass tube and absorber tube are 1500, 47 and 37 mm, respectively. In this experimental setup, we have a header (heat exchanger) of square shape (190 mm x 190 mm). The length of header is 1500 mm. The header consists of a hollow pipe in the center whose diameter is 60 mm through which the air is made to flow. The experimental setup contains approximately 108 liters of water. Water is working as heat collecting medium which collects the solar heat falling on the tubes. This heat is delivered to the air flowing through the header pipe. This heat flow is due to natural convection and conduction. The outlet air temperature depends upon several factors along with air flow rate and solar radiation intensity. The study has been done for both up-flow and down-flow of air in header in similar weather conditions, at different flow rates. In the present investigations the study has been made to find the effect of intensity of solar radiations and flow rate of air on the out let temperature of the air with time and which flow is more efficient. The obtained results show that the system is highly effective for the heating in this region. Moreover, it has been observed that system is highly efficient for the particular flow rate of air. It was also observed that downflow configuration is more effective than up-flow condition at all flow rates due to lesser losses in down-flow. The results show that temperature differences of upper head and lower head, both of water and surface of pipes on the respective ends is lower in down-flow.
Abstract: The significance of psychology in studying politics
is embedded in philosophical issues as well as behavioural
pursuits. For the former is often associated with Sigmund Freud
and his followers. The latter is inspired by the writings of Harold
Lasswell. Political psychology or psychopolitics has its own
impression on political thought ever since it deciphers the concept
of human nature and political propaganda. More importantly,
psychoanalysis views political thought as a textual content which
needs to explore the latent from the manifest content. In other
words, it reads the text symptomatically and interprets the hidden
truth. This paper explains the paradigm of dream interpretation
applied by Freud. The dream work is a process which has four
successive activities: condensation, displacement, representation
and secondary revision. The texts dealing with political though can
also be interpreted on these principles. Freud's method of dream
interpretation draws its source after the hermeneutic model of
philological research. It provides theoretical perspective and
technical rules for the interpretation of symbolic structures. The
task of interpretation remains a discovery of equivalence of
symbols and actions through perpetual analogies. Psychoanalysis
can help in studying political thought in two ways: to study the text
distortion, Freud's dream interpretation is used as a paradigm
exploring the latent text from its manifest text; and to apply Freud's
psychoanalytic concepts and theories ranging from individual mind
to civilization, religion, war and politics.
Abstract: TTV is an unenveloped circular single-stranded DNA
virus with a diameter of 30-32 nm that first was described in 1997 in
Japan. TTV was detected in various populations without proven
pathology, including blood donors and in patients with chronic HBV
and HCV hepatitis. The aim of this study was to determine the
prevalence of TTV DNA in Iranian patients with chronic hepatitis B
and C. Viral TTV-DNA was studied in 442 samples (202 with HBV,
138 with HCV and 102 controls) collected from west south of Iran.
All extracted serum DNA was amplified by TTV ORF1 gene specific
primers using the semi nested PCR technique. TTV DNA was
detected in the serum of 8.9% and 10.8% patients with chronic
hepatitis B and C, respectively. Prevalence of TTV-DNA in the serum
of 102 controls was 2.9%. Results showed significant relation of TTV
with HBV and HCV in patients by using T test examination (P
Abstract: In this paper we present a novel error model for
packet loss and subsequent error description. The proposed model
simulates the error performance of wireless communication link. The
model is designed as two independent Markov chains, where the first
one is used for packet generation and the second one generates
correctly and incorrectly transmitted bits for received packets from
the first chain. The statistical analyses of real communication on the
wireless link are used for determination of model-s parameters. Using
the obtained parameters and the implementation of the generator, we
collected generated traffic. The obtained results generated by
proposed model are compared with the real data collection.
Abstract: Although the field of parametric Pattern Recognition (PR) has been thoroughly studied for over five decades, the use of the Order Statistics (OS) of the distributions to achieve this has not been reported. The pioneering work on using OS for classification was presented in [1] for the Uniform distribution, where it was shown that optimal PR can be achieved in a counter-intuitive manner, diametrically opposed to the Bayesian paradigm, i.e., by comparing the testing sample to a few samples distant from the mean. This must be contrasted with the Bayesian paradigm in which, if we are allowed to compare the testing sample with only a single point in the feature space from each class, the optimal strategy would be to achieve this based on the (Mahalanobis) distance from the corresponding central points, for example, the means. In [2], we showed that the results could be extended for a few symmetric distributions within the exponential family. In this paper, we attempt to extend these results significantly by considering asymmetric distributions within the exponential family, for some of which even the closed form expressions of the cumulative distribution functions are not available. These distributions include the Rayleigh, Gamma and certain Beta distributions. As in [1] and [2], the new scheme, referred to as Classification by Moments of Order Statistics (CMOS), attains an accuracy very close to the optimal Bayes’ bound, as has been shown both theoretically and by rigorous experimental testing.
Abstract: Due to adverse pressure gradient along the diverging
walls of wide-angled diffusers, the attached flow separates from
one wall and remains attached permanently to the other wall in a
process called stalling. Stalled diffusers render the whole fluid flow
system, in which they are part of, very inefficient. There is then an
engineering need to try to understand the whole process of diffuser
stall if any meaningful attempts to improve on diffuser efficiency
are to be made. In this regard, this paper provides a data bank
contribution for the mean flow-field in wide-angled diffusers where
the complete velocity and static pressure fields, and pressure recovery
data for diffusers in the fully stalled flow regime are experimentally
measured. The measurements were carried out at Reynolds numbers
between 1.07×105 and 2.14×105 based on inlet hydraulic diameter
and centreline velocity for diffusers whose divergence angles were
between 30Ôùª and 50Ôùª. Variation of Reynolds number did not significantly
affect the velocity and static pressure profiles. The wall static
pressure recovery was found to be more sensitive to changes in the
Reynolds number. By increasing the velocity from 10 m/s to 20 m/s,
the wall static pressure recovery increased by 8.31%. However, as the
divergence angle was increased, a similar increase in the Reynolds
number resulted in a higher percentage increase in pressure recovery.
Experimental results showed that regardless of the wall to which
the flow was attached, both the velocity and pressure fields were
replicated with discrepancies below 2%.
Abstract: A simple network model is developed in OPNET to
study the performance of the Wi-Fi protocol. The model is simulated
in OPNET and performance factors such as load, throughput and delay
are analysed from the model. Four applications such as oracle, http, ftp
and voice are applied over the Wireless LAN network to determine the
throughput. The voice application utilises a considerable amount of
bandwidth of up to 5Mbps, as a result the 802.11g standard of the
Wi-Fi protocol was chosen which can support a data rate of up to
54Mbps. Results indicate that when the load in the Wi-Fi network is
increased the queuing delay on the point-to-point links in the Wi-Fi
network significantly reduces until it is comparable to that of WiMAX.
In conclusion, the queuing delay of the Wi-Fi protocol for the network
model simulated was about 0.00001secs comparable to WiMAX
network values.
Abstract: In this study, ZnO nano rods and ZnO ultrafine particles were synthesized by Gel-casting method. The synthesized ZnO powder has a hexagonal zincite structure. The ZnO aggregates with rod-like morphology are typically 1.4 μm in length and 120 nm in diameter, which consist of many small nanocrystals with diameters of 10 nm. Longer wires connected by many hexahedral ZnO nanocrystals were obtained after calcinations at the temperature over 600° C.The crystalline structures and morphologies of the powder have been characterized by X-ray diffraction(XRD) and Scaning electron microscopy (SEM).The result shows that the different preparation conditions such as concentration H2O, calcinations time and calcinations temperature have a lot of influences upon the properties of nano ZnO powders, an increase in the temperature of the calcinations results in an increase of the grain size and also the increase of the calcinations time in high temperature makes the size of the grains bigger. The existences of extra watter prevent nano grains from improving like rod morphology. We have obtained the smallest grain size of ZnO powder by controlling the process conditions. Finally In a suitable condition, a novel nanostructure, namely bi-rod-like ZnO nano rods was found which is different from known ZnO nanostructures.
Abstract: The development of wearable sensing technologies is a great challenge which is being addressed by the Proetex FP6 project (www.proetex.org). Its main aim is the development of wearable sensors to improve the safety and efficiency of emergency personnel. This will be achieved by continuous, real-time monitoring of vital signs, posture, activity, and external hazards surrounding emergency workers. We report here the development of carbon dioxide (CO2) sensing boot by incorporating commercially available CO2 sensor with a wireless platform into the boot assembly. Carefully selected commercially available sensors have been tested. Some of the key characteristics of the selected sensors are high selectivity and sensitivity, robustness and the power demand. This paper discusses some of the results of CO2 sensor tests and sensor integration with wireless data transmission
Abstract: The main objective of this study was to determine the effects
of vermicompost and amino acids on the qualitative and quantitative yield of
chamomile. The experiment was conducted during the growing season of
2010 at the Alborz Medical Research Center. The Treatment groups consisted
of vermicompost (0, 5, 10, 15 and 20 tons/ha) and the sprays of amino acids
(budding stag, flowering stage, and budding + flowering stage). The
experimental design was a factorial experiment based on Randomized
Complete Block Design (RCBD) with three replications. The present results
have shown that the highest plant height, flower head diameter, fresh and dry
flower yield and significant essential oil content were obtained by using 20-
ton vermicompost per hectare. Effects of amino acids were similar to those
seen in vermicompost treatment and all measured traits were seen to be
significant after the spray of amino acids at the budding + flowering stage).
Abstract: Graph transformation has recently become more and
more popular as a general visual modeling language to formally state
the dynamic semantics of the designed models. Especially, it is a
very natural formalism for languages which basically are graph (e.g.
UML). Using this technique, we present a highly understandable yet
precise approach to formally model and analyze the behavioral
semantics of UML 2.0 Activity diagrams. In our proposal, AGG is
used to design Activities, then using our previous approach to model
checking graph transformation systems, designers can verify and
analyze designed Activity diagrams by checking the interesting
properties as combination of graph rules and LTL (Linear Temporal
Logic) formulas on the Activities.
Abstract: In this experimental study, performance of a counter
flow Ranque-Hilsch vortex tube (RHVT) with threads cut on its inner
surface was investigated experimentally (pitch is 1 and 2 mm). The
inner diameter of the vortex tube used was D=9 mm and the ratio of
the tube’s length to diameter was L/D=12. The experimental system
was a thermodynamic open system. Flow was controlled by a valve
on the hot outlet side, where the valve was changed from a nearly
closed position to its nearly open position. Fraction of cold flow (ξ) =
0.1-0.9, was determined under 300 and 350 kPa pressurized air. All
experimental data were compared with each other, the maximum
heating performance of the RHVT system was found to be 38.2 oC
and the maximum cooling performance of the RHVT in this study
was found to be -30.9 oC at pitch 1 mm.
Abstract: The carbon based coils with the nanometer scale have
the 3 dimension helix geometry. We synthesized the carbon nano-coils
by the use of chemical vapor deposition technique with iron and tin as
the catalysts. The fabricated coils have the external diameter of
ranging few hundred nm to few thousand nm. The Scanning
Electro-Microscope (SEM) and Tunneling Electro-Microscope has
shown detail images of the coil-s structure. The fabrication of the
carbon nano-coils can be grown on the metal and non-metal substrates,
such as the stainless steel and silicon substrates. Besides growth on the
flat substrate; they also can be grown on the stainless steel wires. After
the synthesis of the coils, the mechanical and electro-mechanical
property is measured. The experimental results were reported.
Abstract: A pot experiment was carried out under controlled
conditions to evaluate the residual effects of different doses of
atrazine+alachlor and foramsulfuron used in corn fields on the
growth and physiology of rapeseed (Brassica napus L.). A split-plot
experiment in CRD with 4 replications was used. The main plots
consisted of herbicide type (atrazine+alachlor mixture and
foramsulfuron) and the sub-plots were different residual doses of the
herbicides (0, 1%, 5%, 10%, 20%, 40%, 50% and 100%). 7 cm
diameter pots were filled with a virgin soil and seeds of rapeseed cv.
Hayola were planted in them. The pots were kept under controlled
conditions for 8 weeks after germination. At harvest, the growth
parameters and the chlorophyll contents of the leaves were
determined. The results showed that the growth of rapeseed plants
was completely prevented at the highest residual doses of the
herbicides (50 and 100 %). The growth parameters of rapeseed plants
were affected by all doses of both types of the herbicide as compared
to the controls. The residual effects of atrazine+alachlor mixture in
reducing the growth parameters of rapeseed were more pronounced
as compared to the residual effects of foramsulfuron alone.
Abstract: It is well known that the abrasive particles in the
abrasive water suspension has significant effect on the erosion
characteristics of the inside surface of the nozzle. Abrasive particles
moving with the flow cause severe skin friction effect, there by
altering the nozzle diameter due to wear which in turn reflects on the
life of the nozzle for effective machining. Various commercial
abrasives are available for abrasive water jet machining. The erosion
characteristic of each abrasive is different. In consideration of this
aspect, in the present work, the effect of abrasive materials namely
garnet, aluminum oxide and silicon carbide on skin friction
coefficient due to wall shear stress and jet kinetic energy has been
analyzed. It is found that the abrasive material of lower density
produces a relatively higher skin friction effect and higher jet exit
kinetic energy.
Abstract: Numerous experimental tests for post-installed anchor systems drilled in hardened concrete were conducted in order to estimate pull-out and shear strength accounting for uncertainties such as torque ratios, embedment depths and different diameters in demands. In this study, the strength of the systems was significantly changed by the effect of those three uncertainties during pull-out experimental tests, whereas the shear strength of the systems was not affected by torque ratios. It was also shown that concrete cone failure or damage mechanism was generally investigated during and after pull-out tests and in shear strength tests, mostly the anchor systems were failed prior to failure of primary structural system. Furthermore, 3D finite element model for the anchor systems was created by ABAQUS for the numerical analysis. The verification of finite element model was identical till the failure points to the load-displacement relationship specified by the experimental tests.