Abstract: Botanical gardens are very significant organizations
which protect the environment against the increasing environmental
problems, provide environmental education for people, offer
recreation possibilities, etc. This article describes botanical gardens
and their functions. The most important function of botanical garden
is to provide environmental education for people and improve
environmental awareness. Considering this function, some botanical
gardens were examined and opinions were suggested about the
subject.
Abstract: Foundation differential settlement and supported
structure tilting are an occasionally occurred engineering problem.
This may be caused by overloading, changes in ground soil properties
or unsupported nearby excavations. Engineering thinking points
directly toward the logic solution for such problem by uplifting the
settled side. This can be achieved with deep foundation elements
such as micro-piles and macro-piles™, jacked piers, and helical piers,
jet grouted mortar columns, compaction grout columns, cement
grouting or with chemical grouting, or traditional pit underpinning
with concrete and mortar. Although, some of these techniques offer
economic, fast and low noise solutions, many of them are quite the
contrary. For tilted structures, with the limited inclination, it may be much
easier to cause a balancing settlement on the less-settlement side
which shall be done carefully in a proper rate. This principal has been
applied in Leaning Tower of Pisa stabilization with soil extraction
from the ground surface. In this research, the authors attempt to
introduce a new solution with a different point of view. So, the
micro-tunneling technique is presented in here as an intended ground
deformation cause. In general, micro-tunneling is expected to induce
limited ground deformations. Thus, the researchers propose to apply
the technique to form small size ground unsupported holes to produce
the target deformations. This shall be done in four phases: 1.
Application of one or more micro-tunnels, regarding the existing
differential settlement value, under the raised side of the tilted
structure. 2. For each individual tunnel, the lining shall be pulled out
from both sides (from jacking and receiving shafts) in the slow rate.
3. If required, according to calculations and site records, an additional
surface load can be applied on the raised foundation side. 4. Finally, a
strengthening soil grouting shall be applied for stabilization after
adjustment. A finite element based numerical model is presented to simulate
the proposed construction phases for different tunneling positions and
tunnels group. For each case, the surface settlements are calculated
and induced plasticity points are checked. These results show the
impact of the suggested procedure on the tilted structure and its
feasibility. Comparing results also show the importance of the
position selection and tunnels group gradual effect. Thus, a new
engineering solution is presented to one of the structural and
geotechnical engineering challenges.
Abstract: Unemployment among the youth is a significant
problem in South Africa. Large corporations and the public sector
simply cannot create enough jobs. Too many youths in South Africa
currently do not consider entrepreneurship as an option in order to
become independent. Unlike the youth of the Netherlands, South
African youth prefer to find employment in the public or private
sector. The Netherlands has a much lower unemployment rate than
South Africa and the Dutch are generally very entrepreneurial. From
early on, entrepreneurship is considered a desirable career option in
the Netherlands. The purpose of this study was to determine whether
there is a difference in the perceptions of some Dutch and South
African students in terms of unemployment and entrepreneurship.
Questionnaires were distributed to students at the North West
University's Vaal Triangle campus in Vanderbijlpark in Gauteng,
South Africa and the Technical University of Delft in the
Netherlands. A descriptive statistical analysis approach was followed
and the means for the independent questions were calculated. The
results demonstrate that the Dutch students are not as concerned
about unemployment after completion of their studies as this is not as
significant a problem as it is in South Africa. Both groups had
positive responses towards the posed questions, but the South African
group felt more strongly about the issues. Both groups of students felt
that there was a need for more practical entrepreneurship training.
The South African education system should focus on practical
entrepreneurship training from a young age.
Abstract: Globally, many women are still disadvantaged when it
comes to business opportunities. Entrepreneurship development
programs, specifically designed to assist women entrepreneurs, are
assisting in solving this problem to a certain extent. The purpose of
this study is to identify the factors that motivate females to start their
own business. Females, from three different groups (2013, 2014 and
2015), who were all enrolled in a short learning program specifically
designed for women in early start-up stage or intending to start a
business, were asked what motivated them to start a business. The
results indicated that, from all three groups, the majority of the
women wanted to start a business to be independent and have
freedom and to add towards a social goal. The results further
indicated that in general, women would enter into entrepreneurship
activity due to pull factors rather than push factors.
Abstract: A Multi-dimensional computational fluid dynamics
(CFD) two-phase model was developed with the aim to simulate
the in-core coolant circuit of a pressurized heavy water reactor
(PHWR) of a commercial nuclear power plant (NPP). Due to the
fact that this PHWR is a Reactor Pressure Vessel type (RPV),
three-dimensional (3D) detailed modelling of the large reservoirs of
the RPV (the upper and lower plenums and the downcomer) were
coupled with an in-house finite volume one-dimensional (1D) code
in order to model the 451 coolant channels housing the nuclear fuel.
Regarding the 1D code, suitable empirical correlations for taking into
account the in-channel distributed (friction losses) and concentrated
(spacer grids, inlet and outlet throttles) pressure losses were used.
A local power distribution at each one of the coolant channels
was also taken into account. The heat transfer between the coolant
and the surrounding moderator was accurately calculated using a
two-dimensional theoretical model. The implementation of subcooled
boiling and condensation models in the 1D code along with the use
of functions for representing the thermal and dynamic properties of
the coolant and moderator (heavy water) allow to have estimations
of the in-core steam generation under nominal flow conditions for a
generic fission power distribution. The in-core mass flow distribution
results for steady state nominal conditions are in agreement with the
expected from design, thus getting a first assessment of the coupled
1/3D model. Results for nominal condition were compared with
those obtained with a previous 1/3D single-phase model getting more
realistic temperature patterns, also allowing visualize low values of
void fraction inside the upper plenum. It must be mentioned that the
current results were obtained by imposing prescribed fission power
functions from literature. Therefore, results are showed with the aim
of point out the potentiality of the developed model.
Abstract: In order to be competitive, companies have to reduce
their production costs while meeting increasing quality requirements.
Therefore, companies try to plan their assembly processes as detailed
as possible. However, increasing product individualization leading to
a higher number of variants, smaller batch sizes and shorter product
life cycles raise the question to what extent the effort of detailed
planning is still justified. An important approach in this field of
research is the concept of determining the economic planning depth
for assembly process planning based on production specific
influencing factors. In this paper first solution hypotheses as well as a
first draft of the resulting method will be presented.
Abstract: In this study, static and dynamic responses of a typical
reinforced concrete solid slab, designed to British Standard (BS 8110:
1997) and under self and live loadings for dance halls are reported.
Linear perturbation analysis using finite element method was
employed for modal, impulse loading and frequency response
analyses of the slab under the aforementioned loading condition.
Results from the static and dynamic analyses, comprising of the slab
fundamental frequencies and mode shapes, dynamic amplification
factor, maximum deflection, stress distributions among other
valuable outcomes are presented and discussed. These were gauged
with the limiting provisions in the design code with a view of
justifying valid optimization objective function for the structure that
can ensure both adequate strength and economical section for large
clear span slabs. This is necessary owing to the continued increase in
cost of erecting building structures and the squeeze on public finance
globally.
Abstract: The education sector is constantly faced with rapid
changes in technologies in terms of ensuring that the curriculum is up
to date and in terms of making sure that students are aware of these
technological changes. This challenge can be seen as the motivation
for this study, which is to examine the factors affecting computing
students’ awareness of the latest Information Technologies (ICTs).
The aim of this study is divided into two sub-objectives which are:
the selection of relevant theories and the design of a conceptual
model to support it as well as the empirical testing of the designed
model. The first objective is achieved by a review of existing
literature on technology adoption theories and models. The second
objective is achieved using a survey of computing students in the four
universities of the KwaZulu-Natal province of South Africa. Data
collected from this survey is analyzed using Statistical package for
the Social Science (SPSS) using descriptive statistics, ANOVA and
Pearson correlations. The main hypothesis of this study is that there is
a relationship between the demographics and the prior conditions of
the computing students and their awareness of general ICT trends and
of Digital Switch Over (DSO) a new technology which involves the
change from analog to digital television broadcasting in order to
achieve improved spectrum efficiency. The prior conditions of the
computing students that were considered in this study are students’
perceived exposure to career guidance and students’ perceived
curriculum currency. The results of this study confirm that gender,
ethnicity, and high school computing course affect students’
perceived curriculum currency while high school location affects
students’ awareness of DSO. The results of this study also confirm
that there is a relationship between students prior conditions and their
awareness of general ICT trends and DSO in particular.
Abstract: A retrospective study conducted at Christian Medical
College (CMC) Teaching Hospital, Vellore, India on 14th August
2014 to assess the accuracy of clinically estimated foetal weight upon
labour admission. Estimating foetal weight is a crucial factor in
assessing maternal and foetal complications during and after labour.
Medical notes of ninety-eight postnatal women who fulfilled the
inclusion criteria were studied to evaluate the correlation between
their recorded Estimated Foetal Weight (EFW) on admission and
actual birth weight (ABW) of the newborn after delivery. Data
concerning maternal and foetal demographics was also noted.
Accuracy was determined by absolute percentage error and
proportion of estimates within 10% of ABW. Actual birth weights
ranged from 950-4080g. A strong positive correlation between EFW
and ABW (r=0.904) was noted. Term deliveries (≥40 weeks) in the
normal weight range (2500-4000g) had a 59.5% estimation accuracy
(n=74) compared to pre-term (4000g) were underestimated by 25% (n=3) and low birthweight
(LBW) babies were overestimated by 12.7% (n=9). Registrars who
estimated foetal weight were accurate in babies within normal weight
ranges. However, there needs to be an improvement in predicting
weight of macrosomic and LBW foetuses. We have suggested the use
of an amended version of the Johnson’s formula for the Indian
population for improvement and a need to re-audit once
implemented.
Abstract: The purpose of this paper is to contribute to the
enhancement of a hydroelectric plant protection by coordinating
protection measures / existing security and introducing new measures
under a risk management process. In addition, plan identifies key
critical elements of a hydroelectric plant, from its level vulnerabilities
and threats it is subjected to in order to achieve the necessary
protection measures to reduce the level of risk.
Abstract: As computing technology advances, smartphone
applications can assist student learning in a pervasive way. For
example, the idea of using mobile apps for the PA Common Trees,
Pests, Pathogens, in the field as a reference tool allows middle school
students to learn about trees and associated pests/pathogens without
bringing a textbook. While working on the development of three heterogeneous mobile
apps, we ran into numerous challenges. Both the traditional waterfall
model and the more modern agile methodologies failed in practice.
The waterfall model emphasizes the planning of the duration for each
phase. When the duration of each phase is not consistent with the
availability of developers, the waterfall model cannot be employed.
When applying Agile Methodologies, we cannot maintain the high
frequency of the iterative development review process, known as
‘sprints’. In this paper, we discuss the challenges and solutions. We
propose a hybrid model known as the Relay Race Methodology to
reflect the concept of racing and relaying during the process of
software development in practice. Based on the development project,
we observe that the modeling of the relay race transition between any
two phases is manifested naturally. Thus, we claim that the RRM
model can provide a de fecto rather than a de jure basis for the core
concept in the software development model. In this paper, the background of the project is introduced first.
Then, the challenges are pointed out followed by our solutions.
Finally, the experiences learned and the future works are presented.
Abstract: Large-scale machine tools for the manufacturing of
large work pieces, e.g. blades, casings or gears for wind turbines,
feature pose-dependent dynamic behavior. Small structural damping
coefficients lead to long decay times for structural vibrations that
have negative impacts on the production process. Typically, these
vibrations are handled by increasing the stiffness of the structure by
adding mass. This is counterproductive to the needs of sustainable
manufacturing as it leads to higher resource consumption both in
material and in energy. Recent research activities have led to higher
resource efficiency by radical mass reduction that is based on controlintegrated
active vibration avoidance and damping methods. These
control methods depend on information describing the dynamic
behavior of the controlled machine tools in order to tune the
avoidance or reduction method parameters according to the current
state of the machine. This paper presents the appearance, consequences and challenges
of the pose-dependent dynamic behavior of lightweight large-scale
machine tool structures in production. It starts with the theoretical
introduction of the challenges of lightweight machine tool structures
resulting from reduced stiffness. The statement of the pose-dependent
dynamic behavior is corroborated by the results of the experimental
modal analysis of a lightweight test structure. Afterwards, the
consequences of the pose-dependent dynamic behavior of lightweight
machine tool structures for the use of active control and vibration
reduction methods are explained. Based on the state of the art of
pose-dependent dynamic machine tool models and the modal
investigation of an FE-model of the lightweight test structure, the
criteria for a pose-dependent model for use in vibration reduction are
derived. The description of the approach for a general posedependent
model of the dynamic behavior of large lightweight
machine tools that provides the necessary input to the aforementioned
vibration avoidance and reduction methods to properly tackle
machine vibrations is the outlook of the paper.
Abstract: This paper is meant to analyze the ranking of
University of Malaysia Terengganu, UMT’s website in the World
Wide Web. There are only few researches have been done on
comparing the ranking of universities’ websites so this research will
be able to determine whether the existing UMT’s website is serving
its purpose which is to introduce UMT to the world. The ranking is
based on hub and authority values which are accordance to the
structure of the website. These values are computed using two websearching
algorithms, HITS and SALSA. Three other universities’
websites are used as the benchmarks which are UM, Harvard and
Stanford. The result is clearly showing that more work has to be done
on the existing UMT’s website where important pages according to
the benchmarks, do not exist in UMT’s pages. The ranking of UMT’s
website will act as a guideline for the web-developer to develop a
more efficient website.
Abstract: Polycyclic Aromatic Hydrocarbons (PAHs) are
formed mainly because of incomplete combustion of organic
materials during industrial, domestic activities or natural occurrence.
Their toxicity and contamination of terrestrial and aquatic ecosystem
have been established. However, with limited validity index, previous
research has focused on PAHs isomer pair ratios of variable
physicochemical properties in source identification. The objective of
this investigation was to determine the empirical validity of Pearson
Correlation Coefficient (PCC) and Cluster Analysis (CA) in PAHs
source identification along soil samples of different land uses.
Therefore, 16 PAHs grouped, as Endocrine Disruption Substances
(EDSs) were determined in 10 sample stations in top and sub soils
seasonally. PAHs was determined the use of Varian 300 gas
chromatograph interfaced with flame ionization detector. Instruments
and reagents used are of standard and chromatographic grades
respectively. PCC and CA results showed that the classification of
PAHs along pyrolitic and petrogenic organics used in source
signature is about the predominance PAHs in environmental matrix.
Therefore, the distribution of PAHs in the studied stations revealed
the presence of trace quantities of the vast majority of the sixteen
PAHs, which may ultimately inhabit the actual source signature
authentication. Therefore, factors to be considered when evaluating
possible sources of PAHs could be; type and extent of bacterial
metabolism, transformation products/substrates, and environmental
factors such as salinity, pH, oxygen concentration, nutrients, light
intensity, temperature, co-substrates, and environmental medium are
hereby recommended as factors to be considered when evaluating
possible sources of PAHs.
Abstract: Well logging records can help to answer many
questions from a wide range of special interested information and
basic petrophysical properties to formation evaluation of oil and gas
reservoirs. The accurate calculations of porosity in carbonate
reservoirs are the most challenging aspects of the well logging
analysis. Many equations have been developed over the years based
on known physical principles or on empirically derived relationships,
which are used to calculate porosity, estimate lithology, and water
saturation; however these parameters are calculated from well logs by
using modern technique in a current study. Nasiriya oil field is one of
the giant oilfields in the Middle East, and the formation under study
is the Mishrif carbonate formation which is the shallowest
hydrocarbon bearing zone in this oilfield. Neurolog software was
used to digitize the scanned copies of the available logs.
Environmental corrections had been made as per Schlumberger charts
2005, which supplied in the Interactive Petrophysics software. Three
saturation models have been used to calculate water saturation of
carbonate formations, which are simple Archie equation, Dual water
model, and Indonesia model. Results indicate that the Mishrif
formation consists mainly of limestone, some dolomite, and shale.
The porosity interpretation shows that the logging tools have a good
quality after making the environmental corrections. The average
formation water saturation for Mishrif formation is around 0.4-
0.6.This study is provided accurate behavior of petrophysical
properties with depth for this formation by using modern software.
Abstract: Non-linear dynamic time history analysis is
considered as the most advanced and comprehensive analytical
method for evaluating the seismic response and performance of
multi-degree-of-freedom building structures under the influence of
earthquake ground motions. However, effective and accurate
application of the method requires the implementation of advanced
hysteretic constitutive models of the various structural components
including masonry infill panels. Sophisticated computational research
tools that incorporate realistic hysteresis models for non-linear
dynamic time-history analysis are not popular among the professional
engineers as they are not only difficult to access but also complex and
time-consuming to use. In addition, commercial computer programs
for structural analysis and design that are acceptable to practicing
engineers do not generally integrate advanced hysteretic models
which can accurately simulate the hysteresis behavior of structural
elements with a realistic representation of strength degradation,
stiffness deterioration, energy dissipation and ‘pinching’ under cyclic
load reversals in the inelastic range of behavior. In this scenario,
push-over or non-linear static analysis methods have gained
significant popularity, as they can be employed to assess the seismic
performance of building structures while avoiding the complexities
and difficulties associated with non-linear dynamic time-history
analysis. “Push-over” or non-linear static analysis offers a practical
and efficient alternative to non-linear dynamic time-history analysis
for rationally evaluating the seismic demands. The present paper is
based on the analytical investigation of the effect of distribution of
masonry infill panels over the elevation of planar masonry infilled
reinforced concrete [R/C] frames on the seismic demands using the
capacity spectrum procedures implementing nonlinear static analysis
[pushover analysis] in conjunction with the response spectrum
concept. An important objective of the present study is to numerically
evaluate the adequacy of the capacity spectrum method using
pushover analysis for performance based design of masonry infilled
R/C frames for near-field earthquake ground motions.
Abstract: Paper deals with the modeling and simulation of energy consumption and GHG production of two different modes of regional passenger transport – road and railway. These two transport modes use the same type of fuel – diesel. Modeling and simulation of the energy consumption in transport is often used due to calculation satisfactory accuracy and cost efficiency. Paper deals with the calculation based on EN standards and information collected from technical information from vehicle producers and characteristics of tracks. Calculation included maximal theoretical capacity of bus and train and real passenger’s measurement from operation. Final energy consumption and GHG production is calculated by using software simulation. In evaluation of the simulation is used system “well to wheel”.
Abstract: The article includes the results and conclusions from
empirical researches that had been done. The research focuses on the
impact of investments made in small and medium-sized enterprises
financed from EU funds on the competitiveness of these companies.
The researches includes financial results in sales revenue and net
income, expenses, and many other new products/services on offer,
higher quality products and services, more modern methods of
production, innovation in management processes, increase in the
number of customers, increase in market share, increase in
profitability of production and provision of services. The main
conclusions are that, companies with direct investments under this
measure shall apply the modern methods of production. The
consequence of this is to increase the quality of our products and
services. Furthermore, both small and medium-sized enterprises have
introduced new products and services. Investments were carried out,
thus enabling better work organization in enterprises. Entrepreneurs
would guarantee higher quality of service, which would result in
better relationships with their customers, what is more, noting the rise
in number of clients. More than half of the companies indicated that
the investments contributed to the increase in market share. Same
thing as for market reach and brand recognition of particular
company. An interesting finding is that, investments in small
enterprises were more effective than medium-sized enterprises.
Abstract: Polymorphism is one of the main pillars of objectoriented
paradigm. It induces hidden forms of class dependencies
which may impact software quality, resulting in higher cost factor for
comprehending, debugging, testing, and maintaining the software. In
this paper, a new cognitive complexity metric called Cognitive
Weighted Polymorphism Factor (CWPF) is proposed. Apart from the
software structural complexity, it includes the cognitive complexity
on the basis of type. The cognitive weights are calibrated based on 27
empirical studies with 120 persons. A case study and experimentation
of the new software metric shows positive results. Further, a
comparative study is made and the correlation test has proved that
CWPF complexity metric is a better, more comprehensive, and more
realistic indicator of the software complexity than Abreu’s
Polymorphism Factor (PF) complexity metric.
Abstract: This study aimed to 1) develop pre-service teachers’
leadership skills through camp-based learning, and 2) develop preservice
teachers’ teamwork skills through camp-based learning. An
applied research methodology was used. The target group was
derived from a purposive selection. It involved 32 fourth-year
students in Early Childhood Education Program enrolling a course
entitled Seminar in Early Childhood Education provided during
second semester of academic year 2013. The treatment was camp-based
learning activities which applied a PDCA process including
four stages: 1) plan, 2) do, 3) check, and 4) act. Research instruments
were a learning camp program, a camp-based learning management
plan, a 5-level assessment form for leadership skills and a 5-level
assessment form for assessing teamwork skills. Data were analyzed
using descriptive statistics. Results were: 1) pre-service teachers’
leadership skills yielded the before treatment average score at x= 3.4,
S.D.=0.6 2and the after-treatment average score at x 4.29 , S.D.=0.66
pre-service teachers’ teamwork skills yielded the before-treatment
average score at x=3.31, S.D.=0.60 and the after-treatment average
score at x=4.42, S.D.=0.66 Both differences were statistically
significant at the .05 level. Thus, the pre-service teachers’ leadership
and teamwork skills were significantly improved through the camp-based
learning approach.