Abstract: Internal combustion engines rejects 30-40% of the
energy supplied by fuel to the environment through exhaust gas. thus, there is a possibility for further significant improvement of efficiency with the utilization of exhaust gas energy and its conversion to mechanical energy or electrical energy. The Thermo-Electric
Generator (TEG) will be located in the exhaust system and will make use of an energy flow between the warmer exhaust gas and the external environment. Predict to th optimum position of temperature
distribution and the performance of TEG through numerical analysis.
The experimental results obtained show that the power output significantly increases with the temperature difference between cold
and hot sides of a thermoelectric generator.
Abstract: An experimental study of Reinforced Concrete, RC, columns strengthened using a steel jacketing technique was conducted. The jacketing technique consisted of four steel vertical angles installed at the corners of the column joined by horizontal steel straps confining the column externally. The effectiveness of the technique was evaluated by testing the RC column specimens under eccentric monotonic loading until failure occurred. Strain gauges were installed to monitor the strains in the internal reinforcement as well as the external jacketing system. The effectiveness of the jacketing technique was demonstrated, and the parameters affecting the technique were studied.
Abstract: This study presents a systematic analysis of wetted region due to cooling of aluminum plate by water spray impingement with respect to different water flow rates, spray nozzle heights, and subcooling. Unlike jet impingement, the wetting is not commenced upon spray impingement and there is a delay in wetness of hot test surface. After initiation, the wetting (black zone) progresses gradually to cover all test plate and provides efficient cooling in nucleate boiling regime. Generally, spray cooling is found function of spray flow rate, spray-to-surface distance and water subcooling. Wetting delay is decreasing by increasing of spray flow rate until spray impact area is not become bigger that test surface. Otherwise, higher spray flow rate is not practically accelerated start of wetting. Very fast wetting due to spray cooling can be obtained by dense spray (high floe rate) discharged from adjacent nozzle to the test surface. Highly subcooling water spray also triggers earlier wetting of hot aluminum plate.
Abstract: This paper addresses the problem of asymptotic tracking
control of a linear parabolic partial differential equation with indomain
point actuation. As the considered model is a non-standard
partial differential equation, we firstly developed a map that allows
transforming this problem into a standard boundary control problem
to which existing infinite-dimensional system control methods can
be applied. Then, a combination of energy multiplier and differential
flatness methods is used to design an asymptotic tracking controller.
This control scheme consists of stabilizing state-feedback derived
from the energy multiplier method and feed-forward control based
on the flatness property of the system. This approach represents
a systematic procedure to design tracking control laws for a class
of partial differential equations with in-domain point actuation. The
applicability and system performance are assessed by simulation
studies.
Abstract: Aquatic and semi aquatic birds as a group are suited to
feed and breed in environments in which water forms a fundamental
part. These birds are biological indicator in aquatic environment,
because these birds belong to the top level of food chain in aquatic
ecosystems. There are 61 species in 14 families of aquatic and semi
aquatic birds in Iran. The birds of the Sattarkhan Lake belong to 16
species in 8 families which include 26.2 percent of total Aquatic and
semi aquatic bird species and 57% of Aquatic and semi aquatic bird's
family of Iran. Study was carried out monthly at Sattarkhan Lake
show the existence of Phalacrocorax carbo, Ardea cinerea, Egretta
alba, Egretta garzetta, Bubulcus ibis, Botaurus stellaris, Sterna
hirundo, Chlidonias leucopterus, Larus minutus, Larus argentatus,
Larus ridibunbus, Alcedo atthis, Ciconia ciconia, Plegadis
falcinellus, Circus aeruginosus, Corvus frugilegus
Abstract: The hybridization of artificial immune system with
cellular automata (CA-AIS) is a novel method. In this hybrid model,
the cellular automaton within each cell deploys the artificial immune
system algorithm under optimization context in order to increase its
fitness by using its neighbor-s efforts. The hybrid model CA-AIS is
introduced to fix the standard artificial immune system-s weaknesses.
The credibility of the proposed approach is evaluated by simulations
and it shows that the proposed approach achieves better results
compared to standard artificial immune system.
Abstract: A total of twenty tensile biopsies were collected from
children undergoing tonsillectomy from teaching hospital ENT
department and Kurdistan private hospital in sulaimani city. All
biopsies were homogenized and cultured; the obtained bacterial
isolates were purified and identified by biochemical tests and VITEK
2 compact system. Among the twenty studied samples, only one
Pseudomonas putida with probability of 99% was isolated.
Antimicrobial susceptibility was carried out by disk diffusion
method, Pseudomonas putida showed resistance to all antibiotics
used except vancomycin. The isolate further subjected to PCR and
DNA sequence analysis of blaVIM gene using different set of primers
for different regions of VIM gene. The results were found to be PCR
positive for the blaVIM gene. To determine the sequence of blaVIM
gene, DNA sequencing performed. Sequence alignment of blaVIM
gene with previously recorded blaVIM gene in NCBI- database showed
that P. putida isolate have different blaVIM gene.
Abstract: The efficient knowledge management system (KMS)
is one of the important strategies to help firms to achieve sustainable
competitive advantages, but little research has been conducted to
understand what contributes to the KMS success. This study thus set
to investigate the determinants of KMS success in the context of Thai
banking industry. A questionnaire survey was conducted in four
major Thai Banks to test the proposed KMS Success model.
The result of this study shows that KMS use and user satisfaction
relate significantly to the success of KMS, and knowledge quality,
service quality and trust lead to system use, and knowledge quality,
system quality and trust lead to user satisfaction. However, this
research focuses only on system and user-related factors. Future
research thus can extend to study factors such as management support
and organization readiness.
Abstract: The growing outsourcing of logistics services
resulting from the ongoing current in firms of costs
reduction/increased efficiency means that it is becoming more and
more important for the companies doing the outsourcing to carry out
a proper evaluation.
The multiple definitions and measures of logistics service
performance found in research on the topic create a certain degree of
confusion and do not clear the way towards the proper measurement
of their performance. Do a model and a specific set of indicators exist
that can be considered appropriate for measuring the performance of
logistics services outsourcing in industrial environments? Are said
indicators in keeping with the objectives pursued by outsourcing? We
aim to answer these and other research questions in the study we have
initiated in the field within the framework of the international High
Performance Manufacturing (HPM) project of which this paper
forms part.
As the first stage of this research, this paper reviews articles
dealing with the topic published in the last 15 years with the aim of
detecting the models most used to make this measurement and
determining which performance indicators are proposed as part of
said models and which are most used. The first steps are also taken in
determining whether these indicators, financial and operational, cover
the aims that are being pursued when outsourcing logistics services.
The findings show there is a wide variety of both models and
indicators used. This would seem to testify to the need to continue
with our research in order to try to propose a model and a set of
indicators for measuring the performance of logistics services
outsourcing in industrial environments.
Abstract: This paper describes a 3D modeling system in
Augmented Reality environment, named 3DARModeler. It can be
considered a simple version of 3D Studio Max with necessary
functions for a modeling system such as creating objects, applying
texture, adding animation, estimating real light sources and casting
shadows. The 3DARModeler introduces convenient, and effective
human-computer interaction to build 3D models by combining both
the traditional input method (mouse/keyboard) and the tangible input
method (markers). It has the ability to align a new virtual object with
the existing parts of a model. The 3DARModeler targets nontechnical
users. As such, they do not need much knowledge of
computer graphics and modeling techniques. All they have to do is
select basic objects, customize their attributes, and put them together
to build a 3D model in a simple and intuitive way as if they were
doing in the real world. Using the hierarchical modeling technique,
the users are able to group several basic objects to manage them as a
unified, complex object. The system can also connect with other 3D
systems by importing and exporting VRML/3Ds Max files. A
module of speech recognition is included in the system to provide
flexible user interfaces.
Abstract: The effect of different combinations of response
feedback on the performance of active control system on nonlinear
frames has been studied in this paper. To this end different feedback
combinations including displacement, velocity, acceleration and full
response feedback have been utilized in controlling the response of
an eight story bilinear hysteretic frame which has been subjected to a
white noise excitation and controlled by eight actuators which could
fully control the frame. For active control of nonlinear frame
Newmark nonlinear instantaneous optimal control algorithm has been
used which a diagonal matrix has been selected for weighting
matrices in performance index. For optimal design of active control
system while the objective has been to reduce the maximum drift to
below the yielding level, Distributed Genetic Algorithm (DGA) has
been used to determine the proper set of weighting matrices. The
criteria to assess the effect of each combination of response feedback
have been the minimum required control force to reduce the
maximum drift to below the yielding drift. The results of numerical
simulation show that the performance of active control system is
dependent on the type of response feedback where the velocity
feedback is more effective in designing optimal control system in
comparison with displacement and acceleration feedback. Also using
full feedback of response in controller design leads to minimum
control force amongst other combinations. Also the distributed
genetic algorithm shows acceptable convergence speed in solving the
optimization problem of designing active control systems.
Abstract: Within the last years, several technologies have been developed to help building e-learning portals. Most of them follow approaches that deliver a vast amount of functionalities, suitable for class-like learning. The SuGI project, as part of the D-Grid (funded by the BMBF), targets on delivering a highly scalable and sustainable learning solution to provide materials (e.g. learning modules, training systems, webcasts, tutorials, etc.) containing knowledge about Grid computing to the D-Grid community. In this article, the process of the development of an e-learning portal focused on the requirements of this special user group is described. Furthermore, it deals with the conceptual and technical design of an e-learning portal, addressing the special needs of heterogeneous target groups. The main focus lies on the quality management of the software development process, Web templates for uploading new contents, the rich search and filter functionalities which will be described from a conceptual as well as a technical point of view. Specifically, it points out best practices as well as concepts to provide a sustainable solution to a relatively unknown and highly heterogeneous community.
Abstract: This paper presents a simple approach for load
flow analysis of a radial distribution network. The proposed
approach utilizes forward and backward sweep algorithm
based on Kirchoff-s current law (KCL) and Kirchoff-s voltage
law (KVL) for evaluating the node voltages iteratively. In this
approach, computation of branch current depends only on the
current injected at the neighbouring node and the current in
the adjacent branch. This approach starts from the end nodes
of sub lateral line, lateral line and main line and moves
towards the root node during branch current computation. The
node voltage evaluation begins from the root node and moves
towards the nodes located at the far end of the main, lateral
and sub lateral lines. The proposed approach has been tested
using four radial distribution systems of different size and
configuration and found to be computationally efficient.
Abstract: It has been shown that in most accidents the driver is responsible due to being distracted or misjudging the situation. In order to solve such problems research has been dedicated to developing driver assistance systems that are able to monitor the traffic situation around the vehicle. This paper presents methods for recognizing several circumstances on a road. The methods use both the in-vehicle warning systems and the roadside infrastructure. Preliminary evaluation results for fog and ice-on-road detection are presented. The ice detection results are based on data recorded in a test track dedicated to tyre friction testing. The achieved results anticipate that ice detection could work at a performance of 70% detection with the right setup, which is a good foundation for implementation. However, the full benefit of the presented cooperative system is achieved by fusing the outputs of multiple data sources, which is the key point of discussion behind this publication.
Abstract: In this paper, an Arabic letter recognition system based on Artificial Neural Networks (ANNs) and statistical analysis for feature extraction is presented. The ANN is trained using the Least Mean Squares (LMS) algorithm. In the proposed system, each typed Arabic letter is represented by a matrix of binary numbers that are used as input to a simple feature extraction system whose output, in addition to the input matrix, are fed to an ANN. Simulation results are provided and show that the proposed system always produces a lower Mean Squared Error (MSE) and higher success rates than the current ANN solutions.
Abstract: Company mergers and acquisitions reached their peak
in the twenty-first century. Mergers and acquisitions have become one
of the competitive strategies for external growth. In general, it is
believed that mergers and acquisitions can create synergies. However,
they require complete information technology system and service
integration, especially in the banking industry. Much of the research
has focused on performance evaluation, shareholder equity allocation,
or even the increase of company market value after the merger and
acquisition, whereas few scholars have focused on information system
integration post merger and acquisition. This study indicates the role
of information systems after a merger and acquisition, explaining the
benefits of information system integration using a merger and
acquisition case in the banking industry as an example. In addition, we
discuss factors that affect the performance of information system
integration, and utilize system dynamics to interpret the relationship
among factors that affect information system integration performance
in the banking industry after a merger and acquisition.
Abstract: The number of users supported in a DS-CDMA
cellular system is typically less than spreading factor (N), and the
system is said to be underloaded. Overloading is a technique to
accommodate more number of users than the spreading factor N. In
O/O overloading scheme, the first set is assigned to the N
synchronous users and the second set is assigned to the additional
synchronous users. An iterative multistage soft decision interference
cancellation (SDIC) receiver is used to remove high level of
interference between the two sets. Performance is evaluated in terms
of the maximum number acceptable users so that the system
performance is degraded slightly compared to the single user
performance at a specified BER. In this paper, the capacity of CDMA
based O/O overloading scheme is evaluated with SDIC receiver. It is
observed that O/O scheme using orthogonal Gold codes provides
25% channel overloading (N=64) for synchronous DS-CDMA
system on an AWGN channel in the uplink at a BER of 1e-5.For a
Rayleigh faded channel, the critical capacity is 40% at a BER of 5e-5
assuming synchronous users. But in practical systems, perfect chip
timing is very difficult to maintain in the uplink.. We have shown that
the overloading performance reduces to 11% for a timing
synchronization error of 0.02Tc for a BER of 1e-5.
Abstract: An effective approach for unbalanced three-phase
distribution power flow solutions is proposed in this paper. The
special topological characteristics of distribution networks have been
fully utilized to make the direct solution possible. Two matrices–the
bus-injection to branch-current matrix and the branch-current to busvoltage
matrix– and a simple matrix multiplication are used to
obtain power flow solutions. Due to the distinctive solution
techniques of the proposed method, the time-consuming LU
decomposition and forward/backward substitution of the Jacobian
matrix or admittance matrix required in the traditional power flow
methods are no longer necessary. Therefore, the proposed method is
robust and time-efficient. Test results demonstrate the validity of the
proposed method. The proposed method shows great potential to be
used in distribution automation applications.
Abstract: Most fingerprint recognition techniques are based on minutiae matching and have been well studied. However, this technology still suffers from problems associated with the handling of poor quality impressions. One problem besetting fingerprint matching is distortion. Distortion changes both geometric position and orientation, and leads to difficulties in establishing a match among multiple impressions acquired from the same finger tip. Marking all the minutiae accurately as well as rejecting false minutiae is another issue still under research. Our work has combined many methods to build a minutia extractor and a minutia matcher. The combination of multiple methods comes from a wide investigation into research papers. Also some novel changes like segmentation using Morphological operations, improved thinning, false minutiae removal methods, minutia marking with special considering the triple branch counting, minutia unification by decomposing a branch into three terminations, and matching in the unified x-y coordinate system after a two-step transformation are used in the work.
Abstract: A feature weighting and selection method is proposed
which uses the structure of a weightless neuron and exploits the
principles that govern the operation of Genetic Algorithms and
Evolution. Features are coded onto chromosomes in a novel way
which allows weighting information regarding the features to be
directly inferred from the gene values. The proposed method is
significant in that it addresses several problems concerned with
algorithms for feature selection and weighting as well as providing
significant advantages such as speed, simplicity and suitability for
real-time systems.