Abstract: For briquetting of metal chips are used hydraulic and
mechanical presses. The density of the briquettes in this case is about
60% - 70 % on the density of solid metal. In this work are presented
the results of experimental studies for briquetting of metal chips, by
using a new technology for impact briquetting. The used chips are by
Armco iron, steel, cast iron, copper, aluminum and brass. It has been
found that: (i) in a controlled impact the density of the briquettes can
be increases up to 30%; (ii) at the same specific impact energy Es
(J/sm3) the density of the briquettes increases with increasing of the
impact velocity; (iii), realization of the repeated impact leads to
decrease of chips density, which can be explained by distribution of
elastic waves in the briquette.
Abstract: In this study, the butt welding of the commercial AZ31 magnesium alloy sheets have been carried out by using Tungsten Inert Gas (TIG) welding process with alternative and pulsed current. Welded samples were examined with regards to hardness and microstructure. Despite some recent developments in welding of magnesium alloys, they have some problems such as porosity, hot cracking, oxide formation and so on. Samples of the welded parts have undergone metallographic and mechanical examination. Porosities and homogeneous micron grain oxides were rarely observed. Orientations of the weld microstructure in terms of heat transfer also were rarely observed and equiaxed grain morphology was dominant grain structure as in the base metal. As results, fusion zone and few locations of the HAZ of the welded samples have shown twin’s grains. Hot cracking was not observed for any samples. Weld bead geometry of the welded samples were evaluated as normal according to welding parameters. In the results, conditions of alternative and pulsed current and the samples were compared to each other with regards to microstructure and hardness.
Abstract: Water suspensions of in-organic (metals and oxides)
and organic nano-objects (chitozan and collagen) were subjected to
the treatment of direct and alternative electrical fields. In addition to
quasi-periodical spatial patterning resonance-like performance of
spatial distributions of these suspensions has been found at low
frequencies of alternating electrical field. These resonances are
explained as the result of creation of equilibrium states of groups of
charged nano-objects with opposite signs of charges at the interparticle
distances where the forces of Coulomb attraction are
compensated by the repulsion forces induced by relatively negative
polarization of hydrated regions surrounding the nanoparticles with
respect to pure water. The low frequencies of these resonances are
explained by comparatively big distances between the particles and
their big masses with t\respect to masses of atoms constituting
molecules with high resonance frequencies. These new resonances
open a new approach to detailed modeling and understanding of
mechanisms of the influence of electrical fields on the functioning of
internal organs of living organisms at the level of cells and neurons.
Abstract: In general, it is desirable to finish the weld quickly,
before a large volume of surrounding metal heats up and expands.
The welding process used, type, welding current and speed of travel,
thus, affect the degree of shrinkage and distortion of a weldment. The
use of mechanized welding equipment reduces welding time, metal
affected zone and consequently distortion. This article helps to define
what weld distortion is and then provide a practical understanding of
the causes of distortion, effects of shrinkage in butt joint welded
assemblies using TI6AL4VA and Aluminium AA2024 alloy sheet.
The beam offset position to the joint interface towards titanium and
aluminium side. The factors affecting distortion during welding is
also given. Test results reveal that welding speed is the significant
parameter to decide the extent of distortion. Also welding from Al
side reduces the distortion while Ti side increases the distortion.
Abstract: Interaction between mixing and crystallization is often
ignored despite the fact that it affects almost every aspect of the
operation including nucleation, growth, and maintenance of the
crystal slurry. This is especially pronounced in multiple impeller
systems where flow complexity is increased. By choosing proper
mixing parameters, what closely depends on the knowledge of the
hydrodynamics in a mixing vessel, the process of batch cooling
crystallization may considerably be improved. The values that render
useful information when making this choice are mixing time and
power consumption. The predominant motivation for this work was
to investigate the extent to which radial dual impeller configuration
influences mixing time, power consumption and consequently the
values of metastable zone width and nucleation rate. In this research,
crystallization of borax was conducted in a 15 dm3 baffled batch
cooling crystallizer with an aspect ratio (H/T) of 1.3. Mixing was
performed using two straight blade turbines (4-SBT) mounted on the
same shaft that generated radial fluid flow. Experiments were
conducted at different values of N/NJS ratio (impeller speed/
minimum impeller speed for complete suspension), D/T ratio
(impeller diameter/crystallizer diameter), c/D ratio (lower impeller
off-bottom clearance/impeller diameter), and s/D ratio (spacing
between impellers/impeller diameter). Mother liquor was saturated at
30°C and was cooled at the rate of 6°C/h. Its concentration was
monitored in line by Na-ion selective electrode. From the values of
supersaturation that was monitored continuously over process time, it
was possible to determine the metastable zone width and
subsequently the nucleation rate using the Mersmann’s nucleation
criterion. For all applied dual impeller configurations, the mixing
time was determined by potentiometric method using a pulse
technique, while the power consumption was determined using a
torque meter produced by Himmelstein & Co. Results obtained in
this investigation show that dual impeller configuration significantly
influences the values of mixing time, power consumption as well as
the metastable zone width and nucleation rate. A special attention
should be addressed to the impeller spacing considering the flow
interaction that could be more or less pronounced depending on the
spacing value.
Abstract: Ultrasonic metal welding has been the subject of ongoing research and development, most recently concentrating on metal joining in miniature devices, for example to allow solder-free wire bonding. As well as at the small scale, there are also opportunities to research the joining of thicker sheet metals and to widen the range of similar and dissimilar materials that can be successfully joined using this technology. This study presents the design, characterisation and test of a lateral-drive ultrasonic metal spot welding device. The ultrasonic metal spot welding horn is modelled using finite element analysis (FEA) and its vibration behaviour is characterised experimentally to ensure ultrasonic energy is delivered effectively to the weld coupon. The welding stack and fixtures are then designed and mounted on a test machine to allow a series of experiments to be conducted for various welding and ultrasonic parameters. Weld strength is subsequently analysed using tensile-shear tests. The results show how the weld strength is particularly sensitive to the combination of clamping force and ultrasonic vibration amplitude of the welding tip, but there are optimal combinations of these and also limits that must be clearly identified.
Abstract: Centrifugal-casting machine is used in manufacturing
special machine components like multi-layer journal bearing used in
all internal combustion engine, steam, gas turbine and air craft turboengine
where isotropic properties and high precisions are desired.
Moreover, this machine can be used in manufacturing thin wall hightech
machine components like cylinder liners and piston rings of IC
engine and other machine parts like sleeves, and bushes. Heavy-duty
machine component like railway wheel can also be prepared by
centrifugal casting. A lot of technological developments are required
in casting process for production of good casted machine body and
machine parts. Usually defects like blowholes, surface roughness,
chilled surface etc. are found in sand casted machine parts. But these
can be removed by centrifugal casting machine using rotating
metallic die. Moreover, die rotation, its temperature control, and good
pouring practice can contribute to the quality of casting because of
the fact that the soundness of a casting in large part depends upon
how the metal enters into the mold or dies and solidifies. Poor
pouring practice leads to variety of casting defects such as
temperature loss, low quality casting, excessive turbulence, over
pouring etc. Besides these, handling of molten metal is very
unsecured and dangerous for the workers. In order to get rid of all
these problems, the need of an automatic pouring device arises. In
this research work, a robot assisted pouring device and a centrifugal
casting machine are designed, developed constructed and tested
experimentally which are found to work satisfactorily. The robot
assisted pouring device is further modified and developed for using it
in actual metal casting process. Lot of settings and tests are required
to control the system and ultimately it can be used in automation of
centrifugal casting machine to produce high-tech machine parts with
desired precision.
Abstract: This paper investigates the application of metallic
coatings on high fiber volume fraction carbon/epoxy polymer matrix
composites. For the grip of the metallic layer, a method of modifying
the surface of the composite by introducing a mixture of copper and
steel powder (filler powders) which can reduce the impact of thermal
spray particles. The powder was introduced to the surface at the time
of the forming. Arc spray was used to project the zinc coating layer.
The substrate was grit blasted to avoid poor adherence. The porosity, microstructure, and morphology of layers are
characterized by optical microscopy, SEM and image analysis. The
samples were studied also in terms of hardness and erosion resistance.
This investigation did not reveal any visible evidence damage to the
substrates. The hardness of zinc layer was about 25.94 MPa and the
porosity was around (∼6.70%). The erosion test showed that the zinc
coating improves the resistance to erosion. Based on the results
obtained, we can conclude that thermal spraying allows the production
of protective coating on PMC. Zinc coating has been identified as a
compatible material with the substrate. The filler powders layer
protects the substrate from the impact of hot particles and allows
avoiding the rupture of brittle carbon fibers.
Abstract: Intellectual capital is one of the most valuable and
important parts of the intangible assets of enterprises especially in
knowledge-based enterprises. With respect to increasing gap between
the market value and the book value of the companies, intellectual
capital is one of the components that can be placed in this gap. This
paper uses the value added efficiency of the three components,
capital employed, human capital and structural capital, to measure the
intellectual capital efficiency of Iranian industries groups, listed in
the Tehran Stock Exchange (TSE), using a 8 years period data set
from 2005 to 2012. In order to analyze the effect of intellectual
capital on the market-to-book value ratio of the companies, the data
set was divided into 10 industries, Banking, Pharmaceutical, Metals
& Mineral Nonmetallic, Food, Computer, Building, Investments,
Chemical, Cement and Automotive, and the panel data method was
applied to estimating pooled OLS. The results exhibited that value
added of capital employed has a positive significant relation with
increasing market value in the industries, Banking, Metals & Mineral
Nonmetallic, Food, Computer, Chemical and Cement, and also,
showed that value added efficiency of structural capital has a positive
significant relation with increasing market value in the Banking,
Pharmaceutical and Computer industries groups. The results of the
value added showed a negative relation with the Banking and
Pharmaceutical industries groups and a positive relation with
computer and Automotive industries groups. Among the studied
industries, computer industry has placed the widest gap between the
market value and book value in its intellectual capital.
Abstract: Pain management is a question of quality of life and
an indicator for nursing quality. Chronic pain which is predominant
in oncology and palliative nursing situations is perceived today as a
multifactorial, individual emotional experience with specific
characteristics including the sociocultural dimension when dealing
with migrant patients. This dimension of chronic pain is of major
importance in professional nursing of migrant patients in hospices or
palliative care units. Objectives of the study are: 1. To find out more
about the sociocultural views on pain and nursing care, on customs
and nursing practices connected with pain of both Turkish Muslim
and German Christian women, 2. To improve individual and family
oriented nursing practice with view to sociocultural needs of patients
in severe pain in palliative care. In a qualitative-explorative comparative study 4 groups of women,
Turkish Muslims immigrants (4 from the first generation, 5 from the
second generation) and German Christian women of two generations
(5 of each age group) of the same age groups as the Turkish women
and with similar educational backgrounds were interviewed (semistructured
ethnographic interviews using Spradley, 1979) on their
perceptions and experiences of pain and nursing care within their
families. For both target groups the presentation will demonstrate the
following results in detail: Utterance of pain as well as “private” and
“public” pain vary within different societies and cultures. Permitted
forms of pain utterance are learned in childhood and determine
attitudes and expectations in adulthood. Language, especially when
metaphors and symbols are used, plays a major role for
misunderstandings. The sociocultural context of illness may include
specific beliefs that are important to the patients and yet seem more
than far-fetched from a biomedical perspective. Pain can be an
influential factor in family relationships where respect or hierarchies
do not allow the direct utterance of individual needs. Specific
resources are often, although not exclusively, linked to religious
convictions and are significantly helpful in reducing pain. The discussion will evaluate the results of the study with view to
the relevant literature and present nursing interventions and
instruments beyond medication that are helpful when dealing with
patients from various socio-cultural backgrounds in painful end-oflife
situations.
Abstract: While the feature sizes of recent Complementary Metal
Oxid Semiconductor (CMOS) devices decrease the influence of static
power prevails their energy consumption. Thus, power savings that
benefit from Dynamic Frequency and Voltage Scaling (DVFS) are
diminishing and temporal shutdown of cores or other microchip
components become more worthwhile. A consequence of powering off unused parts of a chip is that the
relative difference between idle and fully loaded power consumption
is increased. That means, future chips and whole server systems gain
more power saving potential through power-aware load balancing,
whereas in former times this power saving approach had only
limited effect, and thus, was not widely adopted. While powering
off complete servers was used to save energy, it will be superfluous
in many cases when cores can be powered down. An important
advantage that comes with that is a largely reduced time to respond
to increased computational demand. We include the above developments in a server power model
and quantify the advantage. Our conclusion is that strategies from
datacenters when to power off server systems might be used in the
future on core level, while load balancing mechanisms previously
used at core level might be used in the future at server level.
Abstract: Landfill leachates contain a number of persistent pollutants, including heavy metals. They have the ability to spread in ecosystems and accumulate in fish which most of them are classified as top-consumers of trophic chains. Fish are freely swimming organisms; but perhaps, due to their species-specific ecological and behavioral properties, they often prefer the most suitable biotopes and therefore, did not avoid harmful substances or environments. That is why it is necessary to evaluate the persistent pollutant dispersion in hydroecosystem using fish tissue metal concentration. In hydroecosystems of hybrid type (e.g. river-pond-river) the distance from the pollution source could be a perfect indicator of such a kind of metal distribution. The studies were carried out in the Kairiai landfill neighboring hybrid-type ecosystem which is located 5 km east of the Šiauliai City. Fish tissue (gills, liver, and muscle) metal concentration measurements were performed on two types of ecologically-different fishes according to their feeding characteristics: benthophagous (Gibel carp, roach) and predatory (Northern pike, perch). A number of mathematical models (linear, non-linear, using log and other transformations) have been applied in order to identify the most satisfactorily description of the interdependence between fish tissue metal concentration and the distance from the pollution source. However, the only one log-multiple regression model revealed the pattern that the distance from the pollution source is closely and positively correlated with metal concentration in all predatory fish tissues studied (gills, liver, and muscle).
Abstract: Ant algorithms are well-known metaheuristics which
have been widely used since two decades. In most of the literature,
an ant is a constructive heuristic able to build a solution from scratch.
However, other types of ant algorithms have recently emerged: the
discussion is thus not limited by the common framework of the
constructive ant algorithms. Generally, at each generation of an ant
algorithm, each ant builds a solution step by step by adding an
element to it. Each choice is based on the greedy force (also called the
visibility, the short term profit or the heuristic information) and the
trail system (central memory which collects historical information of
the search process). Usually, all the ants of the population have the
same characteristics and behaviors. In contrast in this paper, a new
type of ant metaheuristic is proposed, namely SMART (for Solution
Methods with Ants Running by Types). It relies on the use of different
population of ants, where each population has its own personality.
Abstract: The present study investigates the effectiveness of
newly designed clayey pellets (fired clay pellets diameter sizes of 5
and 8 mm, and unfired clay pellets with the diameter size of 15 mm)
as the beds in the column adsorption process. The adsorption
experiments in the batch mode were performed before the column
experiment with the purpose to determine the order of adsorbent
package in the column which was to be designed in the investigation.
The column experiment was performed by using a known mass of the
clayey beds and the volume of the waste printing developer, which
was purified. The column was filled in the following order: fired clay
pellets of the diameter size of 5 mm, fired clay pellets of the diameter
size of 8 mm, and unfired clay pellets of the diameter size of 15 mm.
The selected order of the adsorbents showed a high removal
efficiency for zinc (97.8%) and copper (81.5%) ions. These
efficiencies were better than those in the case of the already existing
mode adsorption. The obtained experimental data present a good
basis for the selection of an appropriate column fill, but further
testing is necessary in order to obtain more accurate results.
Abstract: Landfill waste is a common problem as it has an
economic and environmental impact even if it is closed. Landfill
waste contains a high density of various persistent compounds such
as heavy metals, organic and inorganic materials. As persistent
compounds are slowly-degradable or even non-degradable in the
environment, they often produce sublethal or even lethal effects on
aquatic organisms. The aims of the present study were to estimate
sublethal effects of the Kairiai landfill (WGS: 55°55‘46.74“,
23°23‘28.4“) leachate on the locomotor activity of rainbow trout
Oncorhynchus mykiss juveniles using the original system package
developed in our laboratory for automated monitoring, recording and
analysis of aquatic organisms’ activity, and to determine patterns of
fish behavioral response to sublethal effects of leachate. Four
different concentrations of leachate were chosen: 0.125; 0.25; 0.5 and
1.0 mL/L (0.0025; 0.005; 0.01 and 0.002 as part of 96-hour LC50,
respectively). Locomotor activity was measured after 5, 10 and 30
minutes of exposure during 1-minute test-periods of each fish (7 fish
per treatment). The threshold-effect-concentration amounted to 0.18
mL/L (0.0036 parts of 96-hour LC50). This concentration was found
to be even 2.8-fold lower than the concentration generally assumed to
be “safe” for fish. At higher concentrations, the landfill leachate
solution elicited behavioral response of test fish to sublethal levels of
pollutants. The ability of the rainbow trout to detect and avoid
contaminants occurred after 5 minutes of exposure. The intensity of
locomotor activity reached a peak within 10 minutes, evidently
decreasing after 30 minutes. This could be explained by the
physiological and biochemical adaptation of fish to altered
environmental conditions. It has been established that the locomotor
activity of juvenile trout depends on leachate concentration and
exposure duration. Modeling of these parameters showed that the
activity of juveniles increased at higher leachate concentrations, but
slightly decreased with the increasing exposure duration. Experiment
results confirm that the behavior of rainbow trout juveniles is a
sensitive and rapid biomarker that can be used in combination with
the system for fish behavior monitoring, registration and analysis to
determine sublethal concentrations of pollutants in ambient water.
Further research should be focused on software improvement aimed
to include more parameters of aquatic organisms’ behavior and to
investigate the most rapid and appropriate behavioral responses in
different species. In practice, this study could be the basis for the
development and creation of biological early-warning systems
(BEWS).
Abstract: The paper presents an additive manufacturing process for the production of metal and composite parts. It is termed as composite metal foil manufacturing and is a combination of laminated object manufacturing and brazing techniques. The process has been described in detail and is being used to produce dissimilar aluminum to copper foil single lap joints. A three dimensional finite element model has been developed to study the thermo-mechanical characteristics of the dissimilar Al/Cu single lap joint. The effects of thermal stress and strain have been analyzed by carrying out transient thermal analysis on the heated plates used to join the two 0.1mm thin metal foils. Tensile test has been carried out on the foils before joining and after the single Al/Cu lap joints are made, they are subjected to tensile lap-shear test to analyze the effect of heat on the foils. The analyses are designed to assess the mechanical integrity of the foils after the brazing process and understand whether or not the heat treatment has an effect on the fracture modes of the produced specimens.
Abstract: The study assessed the effectiveness of Pawpaw
(Carica papaya) wood in reducing the concentrations of heavy
metals in wastewater acting as a bio-sorbent. The following heavy
metals were considered; Zinc, Cadmium, Lead, Copper, Iron,
Selenium, Nickel and Manganese. The physiochemical properties of
Carica papaya stem were studied. The experimental sample was
sourced from the trunk of a felled matured pawpaw tree. Wastewater
for experimental use was prepared by dissolving soil samples
collected from a dump site at Owerri, Imo state of Nigeria in water.
The concentration of each metal remaining in solution as residual
metal after bio-sorption was determined using Atomic absorption
Spectrometer. The effects of pH and initial heavy metal concentration
were studied in a batch reactor. The results of Spectrometer test
showed that there were different functional groups detected in the
Carica papaya stem biomass. There was increase in metal removal as
the pH increased for all the metals considered except for Nickel and
Manganese. Optimum bio-sorption occurred at pH 5.9 with 5g/100ml
solution of bio-sorbent. The results of the study showed that the
treated wastewater is fit for irrigation purpose based on Canada
wastewater quality guideline for the protection of Agricultural
standard. This approach thus provides a cost effective and
environmentally friendly option for treating wastewater.
Abstract: With the advancement of knowledge about the utility
and impact of sustainability, its feasibility has been explored into
different walks of life. Scientists, however; have established their
knowledge in four areas viz environmental, economic, social and
cultural, popularly termed as four pillars of sustainability. Aspects of
environmental and economic sustainability have been rigorously
researched and practiced and huge volume of strong evidence of
effectiveness has been founded for these two sub-areas. For the social
and cultural aspects of sustainability, dependable evidence of
effectiveness is still to be instituted as the researchers and
practitioners are developing and experimenting methods across the
globe. Therefore, the present research aimed to identify globally used
practices of social and cultural sustainability and through evidence
synthesis assess their outcomes to determine the effectiveness of
those practices. A PICO format steered the methodology which
included all populations, popular sustainability practices including
walkability/cycle tracks, social/recreational spaces, privacy, health &
human services and barrier free built environment, comparators
included ‘Before’ and ‘After’, ‘With’ and ‘Without’, ‘More’ and
‘Less’ and outcomes included Social well-being, cultural coexistence,
quality of life, ethics and morality, social capital, sense of
place, education, health, recreation and leisure, and holistic
development. Search of literature included major electronic
databases, search websites, organizational resources, directory of
open access journals and subscribed journals. Grey literature,
however, was not included. Inclusion criteria filtered studies on the
basis of research designs such as total randomization, quasirandomization,
cluster randomization, observational or single studies
and certain types of analysis. Studies with combined outcomes were
considered but studies focusing only on environmental and/or
economic outcomes were rejected. Data extraction, critical appraisal
and evidence synthesis was carried out using customized tabulation,
reference manager and CASP tool. Partial meta-analysis was carried
out and calculation of pooled effects and forest plotting were done.
As many as 13 studies finally included for final synthesis explained
the impact of targeted practices on health, behavioural and social
dimensions. Objectivity in the measurement of health outcomes
facilitated quantitative synthesis of studies which highlighted the
impact of sustainability methods on physical activity, Body Mass
Index, perinatal outcomes and child health. Studies synthesized
qualitatively (and also quantitatively) showed outcomes such as
routines, family relations, citizenship, trust in relationships, social
inclusion, neighbourhood social capital, wellbeing, habitability and
family’s social processes. The synthesized evidence indicates slight
effectiveness and efficacy of social and cultural sustainability on the
targeted outcomes. Further synthesis revealed that such results of this
study are due weak research designs and disintegrated implementations. If architects and other practitioners deliver their
interventions in collaboration with research bodies and policy
makers, a stronger evidence-base in this area could be generated.
Abstract: This first-attempt study revealed that decolorized
intermediates of azo dyes could act as redox mediators to assist
wastewater (WW) decolorization due to enhancement of
electron-transport phenomena. Electrochemical impedance spectra
indicated that hydroxyl and amino-substituent(s) were functional
group(s) as redox-mediator(s). As azo dyes are usually multiple
benzene-rings structured, their derived decolorized intermediates are
likely to play roles of electron shuttles due to lower barrier of energy
gap for electron shuttling. According to cyclic voltammetric profiles,
redox mediating characteristics of decolorized intermediates of azo
dyes (e.g., RBu171, RR198, RR141, RBk5) were clearly disclosed.
With supplementation of biodecolorized metabolites of RR141 and
198, decolorization performance of could be evidently augmented.
This study also suggested the optimal modes of microbial fuel cell
(MFC)-assisted WW decolorization would be plug-flow or batch
mode of operation with no mix. Single chamber-MFCs would be more
favourable than double chamber MFCs due to non-mixing contacting
reactor scheme for operation.
Abstract: In the present work, forming limit diagrams and strain
distribution profile diagrams for extra deep drawing steel at room and
elevated temperatures have been determined experimentally by
conducting stretch forming experiments by using designed and
fabricated warm stretchforming tooling setup. With the help of
forming Limit Diagrams (FLDs) and strain, distribution profile
diagrams the formability of Extra Deep Drawing steel has been
analyzed and co-related with mechanical properties like strain
hardening COEFFICIENT (n) and normal anisotropy (r−). Mechanical
properties of EDD steel from room temperature to 4500C were
determined and discussed the impact of temperature on the properties
like work hardening exponent (n) anisotropy (r-) and strength
coefficient of the material. In addition, the fractured surfaces after
stretching have undergone the some metallurgical investigations and
attempt has been made to co-relate with the formability of EDD steel
sheets. They are co-related and good agreement with FLDs at various
temperatures.