Abstract: In this paper we present a new method for over-height
vehicle detection in low headroom streets and highways using digital
video possessing. The accuracy and the lower price comparing to
present detectors like laser radars and the capability of providing
extra information like speed and height measurement make this
method more reliable and efficient. In this algorithm the features are
selected and tracked using KLT algorithm. A blob extraction
algorithm is also applied using background estimation and
subtraction. Then the world coordinates of features that are inside the
blobs are estimated using a noble calibration method. As, the heights
of the features are calculated, we apply a threshold to select overheight
features and eliminate others. The over-height features are
segmented using some association criteria and grouped using an
undirected graph. Then they are tracked through sequential frames.
The obtained groups refer to over-height vehicles in a scene.
Abstract: This paper presents a low cost automatic system for
sampling the electric field in a limited area. The scanning area is a
flat surface parallel to the ground at a selected height. We discuss
in detail the hardware, software and all the arrangements involved
in the system operation. In order to show the system performance
we include a campaign of narrow band measurements with 6017
sample points in the surroundings of a cellular base station. A
commercial isotropic antenna with three orthogonal axes was used
as sampling device. The results are analyzed in terms of its space
average, standard deviation and statistical distribution.
Abstract: In order to investigate water deficit stress on 24 of
soybean (Glycine Max. L) cultivars and lines in temperate climate, an
experiment was conducted in Iran Seed and Plant Improvement
Institute. Stress levels were irrigation after evaporation of 50, 100,
150 mm water from pan, class A. Randomized Completely Block
Design was arranged for each stress levels. Some traits such as, node
number, plant height, pod number per area, grain number per pod,
grain number per area, 1000 grains weight, grain yield and harvest
index were measured. Results showed that water deficit stress had
significant effect on node number, plant height, pod number per area,
grain number per pod, grain number per area, 1000 grains weight and
harvest index. Also all of agronomic traits except harvest index
influenced significantly by cultivars and lines. The least and most
grain yield was belonged to Ronak X Williams and M41 x Clark
respectively.
Abstract: In this study, a longitudinal joint connection was
proposed for the short-span slab-type modular bridges with rapid
construction. The slab-type modular bridge consists of a number of
precast slab modules and has the joint connection between the
modules in the longitudinal direction of the bridge. A finite element
based parameter analysis was conducted to design the shape and the
dimensions of the longitudinal joint connection. Numbers of shear
keys within the joint, height and depth of the shear key, tooth angle,
and the spacing were considered as the design parameters. Using the
local cracking load at the corner of the shear key and the
cross-sectional area of the joint, an efficiency factor was proposed to
evaluate the effectiveness of the longitudinal joint connection. The
dimensions of shear key were determined by comparing the cracking
loads and the efficiency factors obtained from the finite element
analysis.
Abstract: PDMS (Polydimethylsiloxane) polymer is a suitable material for biological and MEMS (Microelectromechanical systems) designers, because of its biocompatibility, transparency and high resistance under plasma treatment. PDMS round channel is always been of great interest due to its ability to confine the liquid with membrane type micro valves. In this paper we are presenting a very simple way to form round shapemicrofluidic channel, which is based on reflow of positive photoresist AZ® 40 XT. With this method, it is possible to obtain channel of different height simply by varying the spin coating parameters of photoresist.
Abstract: Undular hydraulic jumps are illustrated by a smooth
rise of the free surface followed by a train of stationary waves. They
are sometimes experienced in natural waterways and rivers. The
characteristics of undular hydraulic jumps are studied here. The
height, amplitude and the main characteristics of undular jump is
depended on the upstream Froude number and aspect ratio. The
experiments were done on the smooth bed flume. These results
compared with other researches and the main characteristics of the
undular hydraulic jump were studied in this article.
Abstract: Numerical analysis for the aerodynamic characteristics
of the WIG (wing-in ground effect) craft with highly cambered and
aspect ratio of one is performed to predict the ground effect for the
case of with- and without- lower-extension endplate. The analysis is
included varying angles of attack from 0 to10 deg. and ground
clearances from 5% of chord to 50%. Due to the ground effect, the lift
by rising in pressure on the lower surface is increased and the
influence of wing-tip vortices is decreased. These two significant
effects improve the lift-drag ratio. On the other hand, the endplate
prevents the high-pressure air escaping from the air cushion at the
wing tip and causes to increase the lift and lift-drag ratio further. It is
found from the visualization of computation results that two wing-tip
vortices are generated from each surface of the wing tip and their
strength are weak and diminished rapidly. Irodov-s criteria are also
evaluated to investigate the static height stability. The comparison of
Irodov-s criteria shows that the endplate improves the deviation of the
static height stability with respect to pitch angles and heights. As the
results, the endplate can improve the aerodynamic characteristics and
static height stability of wings in ground effect, simultaneously.
Abstract: The coalescer process is one of the methods for oily water treatment by increasing the oil droplet size in order to enhance the separating velocity and thus effective separation. However, the presence of surfactants in an oily emulsion can limit the obtained mechanisms due to the small oil size related with stabilized emulsion. In this regard, the purpose of this research is to improve the efficiency of the coalescer process for treating the stabilized emulsion. The effects of bed types, bed height, liquid flow rate and stage coalescer (step-bed) on the treatment efficiencies in term of COD values were studied. Note that the treatment efficiency obtained experimentally was estimated by using the COD values and oil droplet size distribution. The study has shown that the plastic media has more effective to attach with oil particles than the stainless one due to their hydrophobic properties. Furthermore, the suitable bed height (3.5 cm) and step bed (3.5 cm with 2 steps) were necessary in order to well obtain the coalescer performance. The application of step bed coalescer process in reactor has provided the higher treatment efficiencies in term of COD removal than those obtained with classical process. The proposed model for predicting the area under curve and thus treatment efficiency, based on the single collector efficiency (ηT) and the attachment efficiency (α), provides relatively a good coincidence between the experimental and predicted values of treatment efficiencies in this study.
Abstract: In the first part of the research work, an electrolyzer (10.16 cm dia and 24.13 cm height) to produce hydrogen and oxygen was constructed for single slice O2/H2 fuel cell using cation exchange membrane. The electrolyzer performance was tested with 23% NaOH, 30% NaOH, 30% KOH and 35% KOH electrolyte solution with current input 4 amp and 2.84 V from the rectifier. Rates of volume of hydrogen produced were 0.159 cm3/sec, 0.155 cm3/sec, 0.169 cm3/sec and 0.163 cm3/sec respectively from 23% NaOH, 30% NaOH, 30% KOH and 35% KOH solution. Rates of volume of oxygen produced were 0.212 cm3/sec, 0.201 cm3/sec, 0.227 cm3/sec and 0.219 cm3/sec respectively from 23% NaOH, 30% NaOH, 30% KOH and 35% KOH solution (1.5 L). In spite of being tested the increased concentration of electrolyte solution, the gas rate does not change significantly. Therefore, inexpensive 23% NaOH electrolyte solution was chosen to use as the electrolyte in the electrolyzer. In the second part of the research work, graphite serpentine flow plates, fiberglass end plates, stainless steel screen electrodes, silicone rubbers were made to assemble the single slice O2/H2 polymer electrolyte membrane fuel cell (PEMFC).
Abstract: The conceptually construction of axially chiral indolostilbenesi.eN-(2-{(E)-2-[2'-(1-Acetyl-1H-indol-2-yl)-3'chloro-4,4',6,6'-tetramethoxy[1,1'-biphenyl]-2yl]ethenyl}phenyl)acetamide and N-(2-{(E)-2-[2'-(1-Acetyl-1H-indol-2-yl)-3'-chloro-2,4',6,6'-tetramethoxy[1,1'-biphenyl]-4-yl]ethenyl}phenyl) acetamide are described in this paper. These structure, were obtained by the tactical combination of palladium-catalyzed coupling which produced 10-acetamido-3,5-dimethoxystilbene, follow by FeCl3-induced oxidative cyclization/dimerisation. All structures were unambiguously confirmed by 1D (1H, 13C) and 2D NMR experiment, (COSY, HMQC, HMBC) and mass spectrometry.