Abstract: With short production development times, there is an increased need to demonstrate product reliability relatively quickly with minimal testing. In such cases there may be few if any observed failures. Thus it may be difficult to assess reliability using the traditional reliability test plans that measure only time (or cycles) to failure. For many components, degradation measures will contain important information about performance and reliability. These measures can be used to design a minimal test plan, in terms of number of units placed on test and duration of the test, necessary to demonstrate a reliability goal. In this work we present a case study involving an electronic component subject to degradation. The data, consisting of 42 degradation paths of cycles to failure, are first used to estimate a reliability function. Bootstrapping techniques are then used to perform power studies and develop a minimal reliability test plan for future production of this component.
Abstract: This study presents an Expert System specially designed to be used with Multiobjective Evolutionary Algorithms (MOEAs) for the solution of the portfolio selection problem. The validation of the proposed hybrid System is done by using data sets from Hang Seng 31 in Hong Kong, DAX 100 in Germany and FTSE 100 in UK. The performance of the proposed system is assessed in comparison with the Non-dominated Sorting Genetic Algorithm II (NSGAII). The evaluation of the performance is based on different performance metrics that evaluate both the proximity of the solutions to the Pareto front and their dispersion on it. The results show that the proposed hybrid system is efficient for the solution of this kind of problems.
Abstract: The development of an low cost acquisition system of S-EMG signals which are reliable, comfortable for the user and with high mobility shows to be a relevant proposition in modern biomedical engineering scenario. In the study, the sampling capacity of the Arduino microcontroller Atmel Atmega328 with an A / D converter with 10-bit resolution and its reconstructing capability of a signal of surface electromyography is analyzed. An electronic circuit to capture the signal through two differential channels was designed, signals from Biceps Brachialis of a healthy man of 21 years was acquired to test the system prototype. ARV, MDF, MNF and RMS estimators were used to compare de acquired signals with physiological values. The Arduino was configured with a sampling frequency of 1.5kHz for each channel, and the tests with the circuit designed offered a SNR of 20.57dB.
Abstract: The calcarenites carbonate rocks of the Quaternary ridges, which extend along the northwestern Mediterranean coastal plain of Egypt, represent an excellent model for the transformation of loose sediments to real sedimentary rocks by the different stages of meteoric diagenesis. The depositional and diagenetic fabrics of the rocks, in addition to the strata orientation, highly affect their ultimate compressive strength and other geotechnical properties.
There is a marked increase in the compressive strength (UCS) from the first to the fourth ridge rock samples. The lowest values are related to the loose packing, weakly cemented aragonitic ooid sediments with high porosity, besides the irregularly distributed of cement, which result in decreasing the ability of these rocks to withstand crushing under direct pressure. The high (UCS) values are attributed to the low porosity, the presence of micritic cement, the reduction in grain size and the occurrence of micritization and calcretization processes.
The strata orientation has a notable effect on the measured (UCS). The lowest values have been recorded for the samples cored in the inclined direction; whereas the highest values have been noticed in most samples cored in the vertical and parallel directions to bedding plane. In case of the inclined direction, the bedding planes were oriented close to the plane of maximum shear stress. The lowest and highest anisotropy values have been recorded for the first and the third ridges rock samples, respectively, which may attributed to the relatively homogeneity and well sorted grainstone of the first ridge rock samples, and relatively heterogeneity in grain and pore size distribution and degree of cementation of the third ridge rock samples, besides, the abundance of shell fragments with intraparticle pore spaces, which may produce lines of weakness within the rock.
Abstract: For vacuum cleaned dust filters there exist no calculation methods to determine design parameters (e.g. traverse velocity of the nozzle, filter area…). In this work a method to calculate the optimum traverse velocity of the nozzle of an industrial-size flat dust filter at a given mean pressure drop and filter face velocity was elaborated. Well-known equations for the design of a cleanable multi-chamber bag-house-filter were modified in order to take into account a continuously regeneration of a dust filter by a nozzle. Thereby, the specific filter medium resistance and the specific cake resistance values are needed which can be derived from filter tests under constant operation conditions.
A lab-scale filter test rig was used to derive the specific filter media resistance value and the specific cake resistance value for vacuum cleaned filter operation. Three different filter media were tested and the determined parameters were compared to each other.
Abstract: To relieve the burden of reasoning on a point to point basis, in many domains there is a need to reduce large and noisy data sets into trends for qualitative reasoning. In this paper we propose and describe a new architectural design pattern called REDUCER for reducing large and noisy data sets that can be tailored for particular situations. REDUCER consists of 2 consecutive processes: Filter which takes the original data and removes outliers, inconsistencies or noise; and Compression which takes the filtered data and derives trends in the data. In this seminal article we also show how REDUCER has successfully been applied to 3 different case studies.
Abstract: This study investigates the level of existence of organized retail crime in supermarkets of Riyadh, Saudi Arabia. The store managers, security managers and general employees were asked about the types of retail crimes occur in the stores. Three independent variables were related to the report of organized retail theft. The independent variables are: 1) the supermarket profile (volume, location, standard and type of the store), 2) the social physical environment of the store (maintenance, cleanness and overall organizational cooperation), 3) the security techniques and loss prevention electronics techniques used. The theoretical framework of this study based on the social disorganization theory. This study concluded that the organized retail theft, in specific, organized theft is moderately apparent in Riyadh stores. The general result showed that the environment of the stores has an effect on the prevalence of organized retail theft with relation to the gender of thieves, age groups, working shift, type of stolen items as well as the number of thieves in one case. Among other reasons, some factors of the organized theft are: economic pressure of customers based on the location of the store. The dealing of theft also was investigated to have a clear picture of stores dealing with organized retail theft. The result showed that mostly, thieves sent without any action and sometimes given written warning. Very few cases dealt with by police. There are other factors in the study can be looked up in the text. This study suggests solving the problem of organized theft; first, is "the well distributing of the duties and responsibilities between the employees especially for security purposes". Second "Installation of strong security system" and "Making well-designed store layout". Third is "giving training for general employees" and "to give periodically security skills training of employees". There are other suggestions in the study can be looked up in the text.
Abstract: Vacant City of Cape Town-owned land lying unutilized and -productive could be developed for land uses such as urban agriculture that may improve the livelihoods of low income families. The new City of Cape Town zoning scheme includes an Urban Agriculture zoning for the first time. Unstructured qualitative interviews among town planners revealed their optimism about this inclusion as it will provide low-income residents with opportunities to generate an income. An existing farming community at Philippi, located within the municipal boundary of the city, was approached and empirical data obtained through questionnaires provided proof that urban agriculture could be viable in a coastal metropolitan city such as Cape Town even if farmers only produce for their own households. The lease method proposed for urban agriculture is a usufruct agreement conferring the right to another party, other than the legal owner, to enjoy the use and advantages of the property.
Abstract: Our study was designed to highlight changes in
certain biochemical parameters (CH, TG, HDL, GOT, GPT, LDL and
CRP), obese women infertile fertile witnesses and research potential
pathophysiological link between obesity and infertility in this
population of women. This practical work was focused on a
population of 24 obese women infertile, compared to controls,
subjects without any pathology causing disruption of parameters to
be studied to determine the contribution of obesity in the etiology of
infertility. The assay results revealed a highly significant difference
between the two groups in serum CH, TG, HDL, TGO and TGP (P
Abstract: Our study was designed to determine the metabolic
changes of some biochemical parameters (cholesterol, triglyceride,
Iron, uric acid, Urea and folic acid) and highlight their changes in 57
women of the region Batna, during the first trimester of pregnancy.
This practical work was done with 27 women with missed
miscarriage, compared with 30 control subjects of normal pregnant
women. The assay results revealed a highly significant difference (P
= 0.0006) between the two groups in serum iron (64.00 vs 93.54) and
in the rate of folate (6.70 vs 9.22) (P
Abstract: The International Building Code (IBC) and the
California Building Code (CBC) both recognize four basic types of
steel seismic resistant frames; moment frames, concentrically braced
frames, shear walls and eccentrically braced frames. Based on
specified geometries and detailing, the seismic performance of these
steel frames is well understood. In 2011, the authors designed an
innovative steel braced frame system with tapering members in the
general shape of a branching tree as a seismic retrofit solution to an
existing four story “lift-slab” building. Located in the seismically
active San Francisco Bay Area of California, a frame of this
configuration, not covered by the governing codes, would typically
require model or full scale testing to obtain jurisdiction approval.
This paper describes how the theories, protocols, and code
requirements of eccentrically braced frames (EBFs) were employed
to satisfy the 2009 International Building Code (IBC) and the 2010
California Building Code (CBC) for seismically resistant steel frames
and permit construction of these nonconforming geometries.
Abstract: In this work, the main problem considered is the
detection and the isolation of the actuator fault. A new formulation of
the linear system is generated to obtain the conditions of the actuator
fault diagnosis. The proposed method is based on the representation
of the actuator as a subsystem connected with the process system in
cascade manner. The designed formulation is generated to obtain the
conditions of the actuator fault detection and isolation. Detectability
conditions are expressed in terms of the invertibility notions. An
example and a comparative analysis with the classic formulation
illustrate the performances of such approach for simple actuator fault
diagnosis by using the linear model of nuclear reactor.
Abstract: As internet continues to expand its usage with an
enormous number of applications, cyber-threats have significantly
increased accordingly. Thus, accurate detection of malicious traffic in
a timely manner is a critical concern in today’s Internet for security.
One approach for intrusion detection is to use Machine Learning (ML)
techniques. Several methods based on ML algorithms have been
introduced over the past years, but they are largely limited in terms of
detection accuracy and/or time and space complexity to run. In this
work, we present a novel method for intrusion detection that
incorporates a set of supervised learning algorithms. The proposed
technique provides high accuracy and outperforms existing techniques
that simply utilizes a single learning method. In addition, our
technique relies on partial flow information (rather than full
information) for detection, and thus, it is light-weight and desirable for
online operations with the property of early identification. With the
mid-Atlantic CCDC intrusion dataset publicly available, we show that
our proposed technique yields a high degree of detection rate over 99%
with a very low false alarm rate (0.4%).
Abstract: This paper presents the results of an experimental
study on the effects of elevated temperature on compressive and
flexural strength of Normal Strength Concrete (NSC), High Strength
Concrete (HSC) and High Performance Concrete (HPC). In addition,
the specimen mass and volume were measured before and after
heating in order to determine the loss of mass and volume during the
test. In terms of non-destructive measurement, ultrasonic pulse
velocity test was proposed as a promising initial inspection method
for fire damaged concrete structure. 100 Cube specimens for three
grades of concrete were prepared and heated at a rate of 3°C/min up
to different temperatures (150, 250, 400, 600, and 900°C). The results
show a loss of compressive and flexural strength for all the concretes
heated to temperature exceeding 400°C. The results also revealed that
mass and density of the specimen significantly reduced with an
increase in temperature.
Abstract: A thin gold metal layer was deposited on the top of
silicon oxide films containing embedded Si nanocrystals (Si-nc). The
sample was annealed in a gas containing nitrogen, and subsequently
characterized by photoluminescence. We obtained 3-fold
enhancement of photon emission from the Si-nc embedded in silicon
dioxide covered with a Gold layer as compared with an uncovered
sample. We attribute this enhancement to the increase of the
spontaneous emission rate caused by the coupling of the Si-nc
emitters with the surface plasmons (SP). The evolution of PL
emission with laser irradiated time was also collected from covered
samples, and compared to that from uncovered samples. In an
uncovered sample, the PL intensity decreases with time,
approximately with two decay constants. Although the decrease of
the initial PL intensity associated with the increase of sample
temperature under CW pumping is still observed in samples covered
with a gold layer, this film significantly contributes to reduce the
permanent deterioration of the PL intensity. The resistance to
degradation of light-emitting silicon nanocrystals can be increased by
SP coupling to suppress the permanent deterioration. Controlling the
permanent photodeterioration can allow to perform a reliable optical
gain measurement.
Abstract: In the age of globalization, higher education
institutions attempt to equip students with global competence. In
response, most universities have been developing and running various
international programs. However, teacher education has been a
neglected area in this trend. Therefore, in this study, we suggest a
program that offers a dual bachelor’s degree from both universities
located on different countries, focusing on teacher education
institutions with different policies and regulations of teacher education
programs that may become obstacles to designing a dual degree
program. We discuss a possible way to get a dual degree including a
teaching certificate at a specialized college, college of secondary
education. To be specific, this research presents a way to attain two
diplomas from Jeju National University (JNU) in Korea and Boise
State University (BSU) in the U.S. It attempts to build an effective
plan for students to declare simultaneous degrees at both universities.
From the study, we find that it takes about 5 years to fulfill
requirements for the dual degree at the undergraduate level.
Abstract: Recently, ‘play of learning’ becomes important and is
emphasized as a useful learning tool. Therefore, interest in
edutainment contents is growing. Storytelling is considered first as a
method that improves the transmission of information and learner's
interest when planning edutainment contents. In this study, we
designed edutainment contents in the form of an adventure game that
applies the storytelling method. This content provides questions and
items constituted dynamically and reorganized learning contents
through analysis of test results. It allows learners to solve various
questions through effective iterative learning. As a result, the learners
can reach mastery learning.
Abstract: The pipe taper thread measurement and uncertainty
normally used the four-wire probe according to the JIS B 0262.
Besides, according to the EA-10/10 standard, the pipe thread could be
measured using the three-wire probe. This research proposed to use
the three-wire probe measuring the pitch diameter of the pipe taper
thread. The measuring accessory component was designed and made,
then, assembled to one side of the ULM 828 CiM machine.
Therefore, this machine could be used to measure and calibrate both
the pipe thread and the pipe taper thread. The equations and the
expanded uncertainty for pitch diameter measurement were
formulated. After the experiment, the results showed that the pipe
taper thread had the pitch diameter equal to 19.165mm and the
expanded uncertainty equal to 1.88µm. Then, the experiment results
were compared to the results from the National Institute of Metrology
Thailand. The equivalence ratio from the comparison showed that
both results were related. Thus, the proposed method of using the
three-wire probe measured the pitch diameter of the pipe taper thread
was acceptable.
Abstract: Several meteorological parameters were used for the
prediction of monthly average daily global solar radiation on
horizontal using recurrent neural networks (RNNs). Climatological
data and measures, mainly air temperature, humidity, sunshine
duration, and wind speed between 1995 and 2007 were used to design
and validate a feed forward and recurrent neural network based
prediction systems. In this paper we present our reference system
based on a feed-forward multilayer perceptron (MLP) as well as the
proposed approach based on an RNN model. The obtained results
were promising and comparable to those obtained by other existing
empirical and neural models. The experimental results showed the
advantage of RNNs over simple MLPs when we deal with time series
solar radiation predictions based on daily climatological data.
Abstract: Industries using conventional fossil fuels have an
interest in better understanding the mechanism of particulate
formation during combustion since such is responsible for emission
of undesired inorganic elements that directly impact the atmospheric
pollution level. Fine and ultrafine particulates have tendency to
escape the flue gas cleaning devices to the atmosphere. They also
preferentially collect on surfaces in power systems resulting in
ascending in corrosion inclination, descending in the heat transfer
thermal unit, and severe impact on human health. This adverseness
manifests particularly in the regions of world where coal is the
dominated source of energy for consumption.
This study highlights the behavior of calcium transformation as
mineral grains verses organically associated inorganic components
during pulverized coal combustion. The influence of existing type of
calcium on the coarse, fine and ultrafine mode formation mechanisms
is also presented. The impact of two sub-bituminous coals on particle
size and calcium composition evolution during combustion is to be
assessed. Three mixed blends named Blends 1, 2, and 3 are selected
according to the ration of coal A to coal B by weight. Calcium
percentage in original coal increases as going from Blend 1 to 3.
A mathematical model and a new approach of describing
constituent distribution are proposed. Analysis of experiments of
calcium distribution in ash is also modeled using Poisson distribution.
A novel parameter, called elemental index λ, is introduced as a
measuring factor of element distribution.
Results show that calcium in ash that originally in coal as mineral
grains has index of 17, whereas organically associated calcium
transformed to fly ash shown to be best described when elemental
index λ is 7.
As an alkaline-earth element, calcium is considered the
fundamental element responsible for boiler deficiency since it is the
major player in the mechanism of ash slagging process. The
mechanism of particle size distribution and mineral species of ash
particles are presented using CCSEM and size-segregated ash
characteristics. Conclusions are drawn from the analysis of
pulverized coal ash generated from a utility-scale boiler.