Abstract: Molecular dynamics simulation of annular flow
boiling in a nanochannel with 70000 particles is numerically
investigated. In this research, an annular flow model is developed to
predict the superheated flow boiling heat transfer characteristics in a
nanochannel. To characterize the forced annular boiling flow in a
nanochannel, an external driving force F ext ranging from 1to12PN
(PN= Pico Newton) is applied along the flow direction to inlet fluid
particles during the simulation. Based on an annular flow model
analysis, it is found that saturation condition and superheat degree
have great influences on the liquid-vapor interface. Also, the results
show that due to the relatively strong influence of surface tension in
small channel, the interface between the liquid film and vapor core is
fairly smooth, and the mean velocity along the stream-wise direction
does not change anymore.
Abstract: The objective of this paper is to characterize the spontaneous Electroencephalogram (EEG) signals of four different motor imagery tasks and to show hereby a possible solution for the present binary communication between the brain and a machine ora Brain-Computer Interface (BCI). The processing technique used in this paper was the fractal analysis evaluated by the Critical Exponent Method (CEM). The EEG signal was registered in 5 healthy subjects,sampling 15 measuring channels at 1024 Hz.Each channel was preprocessed by the Laplacian space ltering so as to reduce the space blur and therefore increase the spaceresolution. The EEG of each channel was segmented and its Fractaldimension (FD) calculated. The FD was evaluated in the time interval corresponding to the motor imagery and averaged out for all the subjects (each channel). In order to characterize the FD distribution,the linear regression curves of FD over the electrodes position were applied. The differences FD between the proposed mental tasks are quantied and evaluated for each experimental subject. The obtained results of the proposed method are a substantial fractal dimension in the EEG signal of motor imagery tasks and can be considerably utilized as the multiple-states BCI applications.
Abstract: Increasing the demand for effectively use of the
production facility requires the tools for sharing the manufacturing
facility through remote operation of the machining process. This
research introduces the methodology of machining technology for
direct remote operation of networked milling machine. The
integrated tools with virtual simulation, remote desktop protocol and
Setup Free Attachment for remote operation of milling process are
proposed. Accessing and monitoring of machining operation is
performed by remote desktop interface and 3D virtual simulations.
Capability of remote operation is supported by an auto setup
attachment with a reconfigurable pin type setup free technology
installed on the table of CNC milling machine to perform unattended
machining process. The system is designed using a computer server
and connected to a PC based controlled CNC machine for real time
monitoring. A client will access the server through internet
communication and virtually simulate the machine activity. The
result has been presented that combination between real time virtual
simulation and remote desktop tool is enabling to operate all machine
tool functions and as well as workpiece setup..
Abstract: Nanostructured materials have attracted many
researchers due to their outstanding mechanical and physical
properties. For example, carbon nanotubes (CNTs) or carbon
nanofibres (CNFs) are considered to be attractive reinforcement
materials for light weight and high strength metal matrix composites.
These composites are being projected for use in structural
applications for their high specific strength as well as functional
materials for their exciting thermal and electrical characteristics. The
critical issues of CNT-reinforced MMCs include processing
techniques, nanotube dispersion, interface, strengthening mechanisms
and mechanical properties. One of the major obstacles to the effective
use of carbon nanotubes as reinforcements in metal matrix
composites is their agglomeration and poor distribution/dispersion
within the metallic matrix. In order to tap into the advantages of the
properties of CNTs (or CNFs) in composites, the high dispersion of
CNTs (or CNFs) and strong interfacial bonding are the key issues
which are still challenging. Processing techniques used for synthesis
of the composites have been studied with an objective to achieve
homogeneous distribution of carbon nanotubes in the matrix.
Modified mechanical alloying (ball milling) techniques have emerged
as promising routes for the fabrication of carbon nanotube (CNT)
reinforced metal matrix composites. In order to obtain a
homogeneous product, good control of the milling process, in
particular control of the ball movement, is essential. The control of
the ball motion during the milling leads to a reduction in grinding
energy and a more homogeneous product. Also, the critical inner
diameter of the milling container at a particular rotational speed can
be calculated. In the present work, we use conventional and modified
mechanical alloying to generate a homogenous distribution of 2 wt.
% CNT within Al powders. 99% purity Aluminium powder (Acros,
200mesh) was used along with two different types of multiwall
carbon nanotube (MWCNTs) having different aspect ratios to
produce Al-CNT composites. The composite powders were processed
into bulk material by compaction, and sintering using a cylindrical
compaction and tube furnace. Field Emission Scanning electron
microscopy (FESEM), X-Ray diffraction (XRD), Raman
spectroscopy and Vickers macro hardness tester were used to
evaluate CNT dispersion, powder morphology, CNT damage, phase
analysis, mechanical properties and crystal size determination.
Despite the success of ball milling in dispersing CNTs in Al powder,
it is often accompanied with considerable strain hardening of the Al
powder, which may have implications on the final properties of the
composite. The results show that particle size and morphology vary
with milling time. Also, by using the mixing process and sonication
before mechanical alloying and modified ball mill, dispersion of the
CNTs in Al matrix improves.
Abstract: It is important to give input information without other device in AR system. One solution is using hand for augmented reality application. Many researchers have proposed different solutions for hand interface in augmented reality. Analyze Histogram and connecting factor is can be example for that. Various Direction searching is one of robust way to recognition hand but it takes too much calculating time. And background should be distinguished with skin color. This paper proposes a hand tracking method to control the 3D object in augmented reality using depth device and skin color. Also in this work discussed relationship between several markers, which is based on relationship between camera and marker. One marker used for displaying virtual object and three markers for detecting hand gesture and manipulating the virtual object.
Abstract: The proof of concept experiments were conducted to
determine the feasibility of using small amounts of Dissolved
Sulphur (DS) from the gaseous phase to precipitate platinum ions in
chloride media. Two sets of precipitation experiments were
performed in which the source of sulphur atoms was either a
thiosulphate solution (Na2S2O3) or a sulphur dioxide gas (SO2). In
liquid-liquid (L-L) system, complete precipitation of Pt was achieved
at small dosages of Na2S2O3 (0.01 – 1.0 M) in a time interval of 3-5
minutes. On the basis of this result, gas absorption tests were carried
out mainly to achieve sulphur solubility equivalent to 0.018 M. The
idea that huge amounts of precious metals could be recovered
selectively from their dilute solutions by utilizing the waste SO2
streams at low pressure seemed attractive from the economic and
environmental point of views. Therefore, mass transfer characteristics
of SO2 gas associated with reactive absorption across the gas-liquid
(G-L) interface were evaluated under different conditions of pressure
(0.5 – 2 bar), solution temperature ranges from 20 – 50 oC and acid
strength (1 – 4 M, HCl). This paper concludes with information about
selective precipitation of Pt in the presence of cations (Fe2+, Co2+,
and Cr3+) in a CSTR and recommendation to scale up laboratory data
to industrial pilot scale operations.
Abstract: Command and Control (C2) system and its interfacethe
Common Operational Picture (COP) are main means that
supports commander in its decision making process. COP contains
information about friendly and enemy unit positions. The friendly
position is gathered via tactical network. In the case of tactical
network failure the information about units are not available. The
tactical simulator can be used as a tool that is capable to predict
movements of units in respect of terrain features. Article deals with
an experiment that was based on Czech C2 system that is in the case
of connectivity lost fed by VR Forces simulator. Article analyzes
maximum time interval in which the position created by simulator is
still usable and truthful for commander in real time.
Abstract: LabVIEW and SIMULINK are two most widely used
graphical programming environments for designing digital signal
processing and control systems. Unlike conventional text-based
programming languages such as C, Cµ and MATLAB, graphical
programming involves block-based code developments, allowing a
more efficient mechanism to build and analyze control systems. In
this paper a LabVIEW environment has been employed as a
graphical user interface for monitoring the operation of a controlled
distillation column, by visualizing both the closed loop performance
and the user selected control conditions, while the column dynamics
has been modeled under the SIMULINK environment. This tool has
been applied to the PID based decoupled control of a binary
distillation column. By means of such integrated environments the
control designer is able to monitor and control the plant behavior and
optimize the response when both, the quality improvement of
distillation products and the operation efficiency tasks, are
considered.
Abstract: Geographical Information Systems are an integral part
of planning in modern technical systems. Nowadays referred to as
Spatial Decision Support Systems, as they allow synergy database
management systems and models within a single user interface
machine and they are important tools in spatial design for
evaluating policies and programs at all levels of administration.
This work refers to the creation of a Geographical Information
System in the context of a broader research in the area of influence
of an under construction station of the new metro in the Greek
city of Thessaloniki, which included statistical and multivariate
data analysis and diagrammatic representation, mapping and
interpretation of the results.
Abstract: Microstructure, wetting behavior and interfacial
reactions between Sn–0.7Cu and Sn–0.3Ag–0.7Cu (SAC0307)
solders solidified on Ni coated Al substrates were compared and
investigated. Microstructure of Sn–0.7Cu alloy exhibited a eutectic
matrix composed of primary β-Sn dendrites with a fine dispersion of
Cu6Sn5 intermetallics whereas microstructure of SAC0307 alloy
exhibited coarser Cu6Sn5 and finer Ag3Sn precipitates of IMCs with
decreased tin dendrites. Contact angles ranging from 22° to 26° were
obtained for Sn–0.7Cu solder solidified on substrate surface whereas
for SAC0307 solder alloy contact angles were found to be in the
range of 20° to 22°. Sn–0.7Cu solder/substrate interfacial region
exhibited faceted (Cu, Ni)6Sn5 IMCs protruding into the solder matrix
and a small amount of (Cu, Ni)3Sn4 intermetallics at the interface.
SAC0307 solder/substrate interfacial region showed mainly (Cu,
Ni)3Sn4 intermetallics adjacent to the coating layer and (Cu,
Ni)6Sn5 IMCs in the solder matrix. The improvement in the
wettability of SAC0307 solder alloy on substrate surface is attributed
to the formation of cylindrical shape (Cu,Ni)6Sn5 and a layer of
(Cu, Ni)3Sn4 IMCs at the interface.
Abstract: This paper describes a novel optimized JTAG interface circuit between a JTAG controller and target IC. Being able to access JTAG using only one or two pins, this circuit does not change the original boundary scanning test frequency of target IC. Compared with the traditional JTAG interface which based on IEEE std. 1149.1, this reduced pin technology is more applicability in pin limited devices, and it is easier to control the scale of target IC for the designer.
Abstract: Cloud Computing is an approach that provides computation and storage services on-demand to clients over the network, independent of device and location. In the last few years, cloud computing became a trend in information technology with many companies that transfer their business processes and applications in the cloud. Cloud computing with service oriented architecture has contributed to rapid development of Geographic Information Systems. Open Geospatial Consortium with its standards provides the interfaces for hosted spatial data and GIS functionality to integrated GIS applications. Furthermore, with the enormous processing power, clouds provide efficient environment for data intensive applications that can be performed efficiently, with higher precision, and greater reliability. This paper presents our work on the geospatial data services within the cloud computing environment and its technology. A cloud computing environment with the strengths and weaknesses of the geographic information system will be introduced. The OGC standards that solve our application interoperability are highlighted. Finally, we outline our system architecture with utilities for requesting and invoking our developed data intensive applications as a web service.
Abstract: Interaction Model plays an important role in Modelbased
Intelligent Interface Agent Architecture for developing
Intelligent User Interface. In this paper we are presenting some
improvements in the algorithms for development interaction model of
interface agent including: the action segmentation algorithm, the
action pair selection algorithm, the final action pair selection
algorithm, the interaction graph construction algorithm and the
probability calculation algorithm. The analysis of the algorithms also
presented. At the end of this paper, we introduce an experimental
program called “Personal Transfer System".
Abstract: Mobile Picture Puzzle is a mobile game application where the player use existing images stored in the mobile phone to create a puzzle to be played. This traditional picture puzzle is not so challenging once the player is familiar with the game. The objective of the developed mobile game application is to have a similar mobile game application that can provide the player with more challenging gaming experience. The developed mobile game application is also a mobile picture puzzle game application to create a puzzle to be played but instead of just using existing images that are stored, the personalised capability allows the player to use the built-in camera phone to capture an image and use the newly captured image to create the puzzle. The development of the mobile game application uses Symbian Operating System (OS), Mobile Media API (Application Programming Interface), Record Management System (RMS) storage and TiledLayer class from Game API.
Abstract: In this paper a novel approach for generalized image
retrieval based on semantic contents is presented. A combination of
three feature extraction methods namely color, texture, and edge
histogram descriptor. There is a provision to add new features in
future for better retrieval efficiency. Any combination of these
methods, which is more appropriate for the application, can be used
for retrieval. This is provided through User Interface (UI) in the
form of relevance feedback. The image properties analyzed in this
work are by using computer vision and image processing algorithms.
For color the histogram of images are computed, for texture cooccurrence
matrix based entropy, energy, etc, are calculated and for
edge density it is Edge Histogram Descriptor (EHD) that is found.
For retrieval of images, a novel idea is developed based on greedy
strategy to reduce the computational complexity. The entire system
was developed using AForge.Imaging (an open source product),
MATLAB .NET Builder, C#, and Oracle 10g. The system was tested
with Coral Image database containing 1000 natural images and
achieved better results.
Abstract: We demonstrate a nonfaradaic electrochemical impedance spectroscopy measurement of biochemically modified gold plated electrodes using a two-electrode system. The absence of any redox indicator in the impedance measurements provide more precise and accurate characterization of the measured bioanalyte at molecular resolution. An equivalent electrical circuit of the electrodeelectrolyte interface was deduced from the observed impedance data of saline solution at low and high concentrations. The detection of biomolecular interactions was fundamentally correlated to electrical double-layer variation at modified interface. The investigations were done using 20mer deoxyribonucleic acid (DNA) strands without any label. Surface modification was performed by creating mixed monolayer of the thiol-modified single-stranded DNA and a spacer thiol (mercaptohexanol) by a two-step self-assembly method. The results clearly distinguish between the noncomplementary and complementary hybridization of DNA, at low frequency region below several hundreds Hertz.
Abstract: One challenging direction of mobile commerce (mcommerce)
that is getting a great deal of attention globally is mobile
financing. The smart-phone and PDA users all around the world are
facing difficulties to become accustomed and trust in m-commerce.
The main rationale can be the slow variation and lack of trust in
mobile payment systems. Mobile payment systems that are in use
need to be more effective and efficient. This paper proposes: the
interface design is not the only factor affecting the m-commerce
adoption and lack of trust; in fact it is the combined effect of
interface usability and trustworthy mobile payment systems, because
it-s the money that the user has to spend at the end of the day, which
the user requires to get transferred securely. The purpose of this
research is to identify the problems regarding the trust and adaption
of m-commerce applications by mobile users and to provide the best
possible solution with respect to human computer interaction (HCI)
principles.
Abstract: Corrosion of metallic water pipelines buried below
ground surface is a function of the nature of the surrounding soil and
groundwater. This gives the importance of knowing the physical and
chemical characteristics of the pipe-s surrounding environment. The
corrosion of externally – unprotected metallic water pipelines,
specially ductile iron pipes, in localities with aggressive soil
conditions is becoming a significant problem. Anticorrosive
protection for metallic water pipelines, their fittings and accessories
is very important, because they may be attached by corrosion with
time. The tendency of a metallic substrate to corrode is a function of
the surface characteristics of the metal and of the metal/protective
film interface, the physical, electrical and electrochemical properties
of the film, and the nature of the environment in which the pipelines
system is placed. In this work the authors have looked at corrosion
problems of water pipelines and their control. The corrosive
properties of groundwater and soil environments are reviewed, and
parameters affecting corrosion are discussed. The purpose of this
work is to provide guidelines for materials selection in water and soil
environments, and how the water pipelines can be protected against
metallic corrosion.
Abstract: One of the approaches enabling people with amputated
limbs to establish some sort of interface with the real world includes
the utilization of the myoelectric signal (MES) from the remaining
muscles of those limbs. The MES can be used as a control input to a
multifunction prosthetic device. In this control scheme, known as the
myoelectric control, a pattern recognition approach is usually utilized
to discriminate between the MES signals that belong to different
classes of the forearm movements. Since the MES is recorded using
multiple channels, the feature vector size can become very large. In
order to reduce the computational cost and enhance the generalization
capability of the classifier, a dimensionality reduction method is
needed to identify an informative yet moderate size feature set. This
paper proposes a new fuzzy version of the well known Fisher-s
Linear Discriminant Analysis (LDA) feature projection technique.
Furthermore, based on the fact that certain muscles might contribute
more to the discrimination process, a novel feature weighting scheme
is also presented by employing Particle Swarm Optimization (PSO)
for estimating the weight of each feature. The new method, called
PSOFLDA, is tested on real MES datasets and compared with other
techniques to prove its superiority.
Abstract: In this paper we report a study aimed at determining
the effects of animation on usability and appeal of educational
software user interfaces. Specifically, the study compares 3
interfaces developed for the Mathsigner™ program: a static
interface, an interface with highlighting/sound feedback, and an
interface that incorporates five Disney animation principles. The
main objectives of the comparative study were to: (1) determine
which interface is the most effective for the target users of
Mathsigner™ (e.g., children ages 5-11), and (2) identify any Gender
and Age differences in using the three interfaces. To accomplish
these goals we have designed an experiment consisting of a
cognitive walkthrough and a survey with rating questions. Sixteen
children ages 7-11 participated in the study, ten males and six
females. Results showed no significant interface effect on user task
performance (e.g., task completion time and number of errors);
however, interface differences were seen in rating of appeal, with
the animated interface rated more 'likeable' than the other two.
Task performance and rating of appeal were not affected
significantly by Gender or Age of the subjects.