Abstract: KSLV-I(Korea Space Launch Vehicle-I) is designed as
a launch vehicle to enter a 100 kg-class satellite to the LEO(Low Earth
Orbit). Attitude angles of the upper-stage, including roll, pitch and
yaw are controlled by the cold gas thruster system using nitrogen gas.
The cold gas thruster is an actuator in the RCS(Reaction Control
System). To design an attitude controller for the upper-stage, thrust
measurement in vacuum condition is required. In this paper, the new
thrust measurement system and calibration mechanism are developed
and measurement errors and signal processing method are presented.
Abstract: Cluster analysis divides data into groups that are
meaningful, useful, or both. Analysis of biological data is creating a
new generation of epidemiologic, prognostic, diagnostic and
treatment modalities. Clustering of protein sequences is one of the
current research topics in the field of computer science. Linear
relation is valuable in rule discovery for a given data, such as if value
X goes up 1, value Y will go down 3", etc. The classical linear
regression models the linear relation of two sequences perfectly.
However, if we need to cluster a large repository of protein sequences
into groups where sequences have strong linear relationship with
each other, it is prohibitively expensive to compare sequences one by
one. In this paper, we propose a new technique named General
Regression Model Technique Clustering Algorithm (GRMTCA) to
benignly handle the problem of linear sequences clustering. GRMT
gives a measure, GR*, to tell the degree of linearity of multiple
sequences without having to compare each pair of them.
Abstract: This paper presents an experimental investigation of
transformer dielectric response and solid insulation water content.
The dielectric response was carried out on the base of Hybrid
Frequency Dielectric Spectroscopy and Polarization Current
measurements method (FDS &PC). The calculation of the water
content in paper is based on the water content in oil and the obtained
equilibrium curves. A reference measurements were performed at
equilibrium conditions for water content in oil and paper of
transformer at different stable temperatures (25, 50, 60 and 70°C) to
prepare references to evaluate the insulation behavior at the not
equilibrium conditions. Some measurements performed at the
different simulated normal working modes of transformer operation
at the same temperature where the equilibrium conditions. The
obtained results show that when transformer temperature is mach
more than the its ambient temperature, the transformer temperature
decreases immediately after disconnecting the transformer from the
network and this temperature reduction influences the transformer
insulation condition in the measuring process. In addition to the oil
temperature at the near places to the sensors, the temperature
uniformity in transformer which can be changed by a big change in
the load of transformer before the measuring time will influence the
result. The investigations have shown that the extremely influence of
the time between disconnecting the transformer and beginning the
measurements on the results. And the online monitoring for water
content in paper measurements, on the basis of the oil water content
on line monitoring and the obtained equilibrium curves. The
measurements where performed continuously and for about 50 days
without any disconnection in the prepared the adiabatic room.
Abstract: This paper presents the development of a software
application for Off-line robot task programming and simulation. Such
application is designed to assist in robot task planning and to direct
manipulator motion on sensor based programmed motion. The
concept of the designed programming application is to use the power
of the knowledge base for task accumulation. In support of the
programming means, an interactive graphical simulation for
manipulator kinematics was also developed and integrated into the
application as the complimentary factor to the robot programming
media. The simulation provides the designer with useful,
inexpensive, off-line tools for retain and testing robotics work cells
and automated assembly lines for various industrial applications.
Abstract: Recent widespread use of information and
communication technology has greatly changed information security
risks that businesses and institutions encounter. Along with this
situation, in order to ensure security and have confidence in electronic
trading, it has become important for organizations to take competent
information security measures to provide international confidence that
sensitive information is secure. Against this backdrop, the approach to
information security checking has come to an important issue, which
is believed to be common to all countries. The purpose of this paper is
to introduce the new system of information security checking program
in Korea and to propose synthetic information security
countermeasures under domestic circumstances in order to protect
physical equipment, security management and technology, and the
operation of security check for securing services on ISP(Internet
Service Provider), IDC(Internet Data Center), and
e-commerce(shopping malls, etc.)
Abstract: Particulate matter (PM) in ambient air is responsible
for adverse health effects in adults and children. Relatively little is
known about the concentrations, sources and health effects of PM in
indoor air. A monitoring study was conducted in Ankara by three
campaigns in order to measure PM levels in indoor and outdoor
environments to identify and quantify associations between sources
and concentrations. Approximately 82 homes (1st campaign for 42,
2nd campaign for 12, and 3rd campaign for 28), three rooms (living
room, baby-s room and living room used as a baby-s room) and
outdoor ambient at each home were sampled with Grimm
Environmental Dust Monitoring (EDM) 107, during different
seasonal periods of 2011 and 2012. In this study, the relationship
between indoor and outdoor PM levels for particulate matter less than
10 micrometer (.m) (PM10), particulate matter less than 2.5.m
(PM2.5) and particulate matter less than 1.0.m (PM1) were
investigated. The mean concentration of PM10, PM2.5, and PM1.0 at
living room used as baby-s room is higher than living and baby-s
room (or bedroom) for three sampling campaigns. It is concluded that
the household activities and environmental conditions are very
important for PM concentrations in the indoor environments during
the sampling periods. The amount of smokers, being near a main
street and/or construction activities increased the PM concentration.
This study is based on the assessment the relationship between indoor
and outdoor PM levels and the household activities and
environmental conditions
Abstract: It is established that the instantaneous heart rate (HR) of healthy humans keeps on changing. Analysis of heart rate variability (HRV) has become a popular non invasive tool for assessing the activities of autonomic nervous system. Depressed HRV has been found in several disorders, like diabetes mellitus (DM) and coronary artery disease, characterised by autonomic nervous dysfunction. A new technique, which searches for pattern repeatability in a time series, is proposed specifically for the analysis of heart rate data. These set of indices, which are termed as pattern repeatability measure and pattern repeatability ratio are compared with approximate entropy and sample entropy. In our analysis, based on the method developed, it is observed that heart rate variability is significantly different for DM patients, particularly for patients with diabetic foot ulcer.
Abstract: The Taiwan Health Literacy Scale (THLS) was developed to cope with the need of measuring heath literacy of Chinese-speaking adults in Taiwan. Although the scale was proven having good reliability and validity, it was not popularly adopted by the practitioners due to the length, and the time required completing. Based on the THLS, this research further invited healthcare professionals to review the original scale for a possible shorten work. Under the logic of THLS, the research adopted an analytic hierarchy process technique to consolidate the healthcare experts- assessments to shorten the original scale. There are fifteen items out of the original 66 items were identified having higher loadings. Confirmed by the experts and passed a pilot test with 40 undergraduate students, a short form of THLS is then introduced. This research then used 839 samples from the major cities of the Hua-lien county in the eastern part of Taiwan to test the reliability and validity of this new scale. The reliability of the scale is high and acceptable. The current scale is also highly correlated with the original, of which provide evidence for the validity of the scale.
Abstract: Recently, the health of retired National Football
League players, particularly lineman has been investigated. A
number of studies have reported increased cardiometabolic risk,
premature cardiovascular disease and incidence of type 2 diabetes.
Rugby union players have somatotypes very similar to National
Football League players which suggests that rugby players may have
similar health risks. The International Golden Oldies World Rugby
Festival (GORF) provided a unique opportunity to investigate the
demographics of veteran rugby players. METHODOLOGIES: A
cross-sectional, observational study was completed using an online
web-based questionnaire that consisted of medical history and
physiological measures. Data analysis was completed using a one
sample t-test (50yrs) and Chi-square test. RESULTS:
A total of 216 veteran rugby competitors (response rate = 6.8%)
representing 10 countries, aged 35-72 yrs (mean 51.2, S.D. ±8.0),
participated in the online survey. As a group, the incidence of current
smokers was low at 8.8% (avg 72.4 cigs/wk) whilst the percentage
consuming alcohol was high (93.1% (avg 11.2 drinks/wk).
Competitors reported the following top six chronic
diseases/disorders; hypertension (18.6%), arthritis (OA/RA, 11.5%),
asthma (9.3%), hyperlipidemia (8.2%), diabetes (all types, 7.5%) and
gout (6%), there were significant differences between groups with
regard to cancer (all types) and migraines. When compared to the
Australian general population (Australian Bureau of Statistics data,
n=18,000), GORF competitors had a significantly lower incidence of
anxiety (p
Abstract: Energy consumption rate during the cooling process
of industrial glass tempering process is considerably high. In this
experimental study the effect of dimensionless jet to jet distance
(S/D) and jet to plate distance (H/D) on the cooling time have been
investigated. In the experiments 4 mm thick glass samples have been
used. Cooling unit consists of 16 mutually placed seamless aluminum
nozzles of 8 mm in diameter and 80 mm in length. Nozzles were in
staggered arrangement. Experiments were conducted with circular
jets for H/D values between 1 and 10, and for S/D values between 2
and 10. During the experiments Reynolds number has been kept
constant at 30000. Experimental results showed that the longest
cooling time with 87 seconds has been observed in the experiments
for S/D=10 and H/D=10 values, while the shortest cooling time with
42.5 seconds has been measured in the experiments for S/D=2 and
H/D=4 values.
Abstract: A greenhouse experiment was conducted to investigate the effects of different types of nutrients induced salinity on the growth, membrane permeability, nitrate reductase activity, proline content and macronutrient concentrations of tomato plants. The plants were subjected to six different treatments: 1 (control) containing basic solution, 2 basic solution+40mM of NaCl, 3 basic solution+40 mM of KNO3, 4 basic solution+20 mM of Ca(NO3)2.4H2O, 5 basic solution+20 mM of Mg(NO3)2.6H2O and 6 basic solution+20 mM of KNO3+5 mM of Ca(NO3)2.4H2O+5 mM of Mg(NO3)2.6H2O. Membrane permeability was increased significantly only with addition of NaCl, and then decreased to its lower level with addition of Ca(NO3)2.4H2O and Mg(NO3)2.6H2O. Proline accumulation were followed the same trend of results when they had been exposed to NaCl salinity. Nitrate reductase activity (NRA) was significantly affected by addition of different types of nutrient induced salinity.
Abstract: Utilization of diverse germplasm is needed to enhance
the genetic diversity of cultivars. The objective of this study was to
evaluate the genetic relationships of 98 alfalfa germplasm accessions
using morphological traits and SSR markers. From the 98 tested
populations, 81 were locals originating in Europe, 17 were introduced
from USA, Australia, New Zealand and Canada. Three primers
generated 67 polymorphic bands. The average polymorphic
information content (PIC) was very high (> 0.90) over all three used
primer combinations. Cluster analysis using Unweighted Pair Group
Method with Arithmetic Means (UPGMA) and Jaccard´s coefficient
grouped the accessions into 2 major clusters with 4 sub-clusters with
no correlation between genetic and morphological diversity. The SSR
analysis clearly indicated that even with three polymorphic primers,
reliable estimation of genetic diversity could be obtained.
Abstract: Limited infrastructure development on peats and
organic soils is a serious geotechnical issues common to many
countries of the world especially Malaysia which distributed 1.5 mill
ha of those problematic soil. These soils have high water content and
organic content which exhibit different mechanical properties and
may also change chemically and biologically with time. Constructing
structures on peaty ground involves the risk of ground failure and
extreme settlement. Nowdays, much efforts need to be done in
making peatlands usable for construction due to increased landuse.
Deep mixing method employing cement as binders, is generally used
as measure again peaty/ organic ground failure problem. Where the
technique is widely adopted because it can improved ground
considerably in a short period of time. An understanding of
geotechnical properties as shear strength, stiffness and compressibility
behavior of these soils was requires before continues construction on
it. Therefore, 1- 1.5 meter peat soil sample from states of Johor and
an organic soil from Melaka, Malaysia were investigated. Cement
were added to the soil in the pre-mixing stage with water cement ratio
at range 3.5,7,14,140 for peats and 5,10,30 for organic soils,
essentially to modify the original soil textures and properties. The
mixtures which in slurry form will pour to polyvinyl chloride (pvc)
tube and cured at room temperature 250C for 7,14 and 28 days.
Laboratory experiments were conducted including unconfined
compressive strength and bender element , to monitor the improved
strength and stiffness of the 'stabilised mixed soils'. In between,
scanning electron miscroscopic (SEM) were observations to
investigate changes in microstructures of stabilised soils and to
evaluated hardening effect of a peat and organic soils stabilised
cement. This preliminary effort indicated that pre-mixing peat and
organic soils contributes in gaining soil strength while help the
engineers to establish a new method for those problematic ground
improvement in further practical and long term applications.
Abstract: A new analysis of perceptual speech enhancement is
presented. It focuses on the fact that if only noise above the masking
threshold is filtered, then noise below the masking threshold, but
above the absolute threshold of hearing, can become audible after the
masker filtering. This particular drawback of some perceptual filters,
hereafter called the maskee-to-audible-noise (MAN) phenomenon,
favours the emergence of isolated tonals that increase musical noise.
Two filtering techniques that avoid or correct the MAN phenomenon
are proposed to effectively suppress background noise without introducing
much distortion. Experimental results, including objective
and subjective measurements, show that these techniques improve
the enhanced speech quality and the gain they bring emphasizes the
importance of the MAN phenomenon.
Abstract: Most of the well known methods for generating
Gaussian variables require at least one standard uniform distributed
value, for each Gaussian variable generated. The length of the
random number generator therefore, limits the number of
independent Gaussian distributed variables that can be generated
meanwhile the statistical solution of complex systems requires a
large number of random numbers for their statistical analysis. We
propose an alternative simple method of generating almost infinite
number of Gaussian distributed variables using a limited number of
standard uniform distributed random numbers.
Abstract: In this paper, based on flume experimental data, the velocity distribution in open channel flows is re-investigated. From the analysis, it is proposed that the wake layer in outer region may be divided into two regions, the relatively weak outer region and the relatively strong outer region. Combining the log law for inner region and the parabolic law for relatively strong outer region, an explicit equation for mean velocity distribution of steady and uniform turbulent flow through straight open channels is proposed and verified with the experimental data. It is found that the sediment concentration has significant effect on velocity distribution in the relatively weak outer region.
Abstract: Hysteresis phenomenon has been observed in the
operations of both horizontal-axis and vertical-axis wind turbines
(HAWTs and VAWTs). In this study, wind tunnel experiments were
applied to investigate the characters of hysteresis phenomena between
the angular speed and the external resistance of electrical loading
during the operation of a Darrieus type VAWT. Data of output voltage,
output current, angular speed of wind turbine under different wind
speeds are measured and analyzed. Results show that the range of
external resistance changes with the wind speed. The range decreases
as the wind speed increases following an exponential decay form.
Experiments also indicate that the maximum output power of wind
turbines is always inside the range where hysteresis happened. These
results provide an important reference to the design of output control
system of wind turbines.
Abstract: The purpose of this research is to study motivation
factors and also to study factors relation to job performance to
compare motivation factors under the personal factor classification
such as gender, age, income, educational level, marital status, and
working duration; and to study the relationship between Motivation
Factors and Job Performance with job satisfactions. The sample
groups utilized in this research were 400 Suan Sunandha Rajabhat
University employees. This research is a quantitative research using
questionnaires as research instrument. The statistics applied for data
analysis including percentage, mean, and standard deviation. In
addition, the difference analysis was conducted by t value computing,
one-way analysis of variance and Pearson’s correlation coefficient
computing. The findings of the study results were as follows the
findings showed that the aspects of job promotion and salary were at
the moderate levels. Additionally, the findings also showed that the
motivations that affected the revenue branch chiefs’ job performance
were job security, job accomplishment, policy and management, job
promotion, and interpersonal relation.
Abstract: Repeated observation of a given area over time yields
potential for many forms of change detection analysis. These
repeated observations are confounded in terms of radiometric
consistency due to changes in sensor calibration over time,
differences in illumination, observation angles and variation in
atmospheric effects.
This paper demonstrates applicability of an empirical relative
radiometric normalization method to a set of multitemporal cloudy
images acquired by Resourcesat1 LISS III sensor. Objective of this
study is to detect and remove cloud cover and normalize an image
radiometrically. Cloud detection is achieved by using Average
Brightness Threshold (ABT) algorithm. The detected cloud is
removed and replaced with data from another images of the same
area. After cloud removal, the proposed normalization method is
applied to reduce the radiometric influence caused by non surface
factors. This process identifies landscape elements whose reflectance
values are nearly constant over time, i.e. the subset of non-changing
pixels are identified using frequency based correlation technique. The
quality of radiometric normalization is statistically assessed by R2
value and mean square error (MSE) between each pair of analogous
band.
Abstract: The process of wafer fabrication is arguably the most
technologically complex and capital intensive stage in semiconductor
manufacturing. This large-scale discrete-event process is highly reentrant,
and involves hundreds of machines, restrictions, and
processing steps. Therefore, production control of wafer fabrication
facilities (fab), specifically scheduling, is one of the most challenging
problems that this industry faces. Dispatching rules have been
extensively applied to the scheduling problems in semiconductor
manufacturing. Moreover, lot release policies are commonly used in
this manufacturing setting to further improve the performance of such
systems and reduce its inherent variability. In this work, simulation is
used in the scheduling of re-entrant flow shop manufacturing systems
with an application in semiconductor wafer fabrication; where, a
simulation model has been developed for the Intel Five-Machine Six
Step Mini-Fab using the ExtendTM simulation environment. The
Mini-Fab has been selected as it captures the challenges involved in
scheduling the highly re-entrant semiconductor manufacturing lines.
A number of scenarios have been developed and have been used to
evaluate the effect of different dispatching rules and lot release
policies on the selected performance measures. Results of simulation
showed that the performance of the Mini-Fab can be drastically
improved using a combination of dispatching rules and lot release
policy.