Abstract: The change of conditions for production companies in
high-wage countries is characterized by the globalization of
competition and the transition of a supplier´s to a buyer´s market. The
companies need to face the challenges of reacting flexibly to these
changes. Due to the significant and increasing degree of automation,
assembly has become the most expensive production process.
Regarding the reduction of production cost, assembly consequently
offers a considerable rationalizing potential. Therefore, an
aerodynamic feeding system has been developed at the Institute of
Production Systems and Logistics (IFA), Leibniz Universitaet
Hannover. This system has been enabled to adjust itself by using a
genetic algorithm. The longer this genetic algorithm is executed the
better is the feeding quality. In this paper, the relation between the
system´s setting time and the feeding quality is observed and a
function which enables the user to achieve the minimum of the total
feeding time is presented.
Abstract: This paper aimed to introduce the solution of concrete
slump recovery using chemical admixture type-F (superplasticizer,
naphthalene base) to the practice in order to solve unusable concrete
problem due to concrete loss its slump, especially for those tropical
countries that have faster slump loss rate. In the other hand, randomly
adding superplasticizer into concrete can cause concrete to segregate.
Therefore, this paper also develops the estimation model used to
calculate amount of second dose of superplasticizer need for concrete
slump recovery. Fresh properties of ordinary Portland cement
concrete with volumetric ratio of paste to void between aggregate
(paste content) of 1.1-1.3 with water-cement ratio zone of 0.30 to
0.67 and initial superplasticizer (naphthalene base) of 0.25%-1.6%
were tested for initial slump and slump loss for every 30 minutes for
one and half hour by slump cone test. Those concretes with slump
loss range from 10% to 90% were re-dosed and successfully
recovered back to its initial slump. Slump after re-dosed was tested
by slump cone test. From the result, it has been concluded that, slump
loss was slower for those mix with high initial dose of
superplasticizer due to addition of superplasticizer will disturb
cement hydration. The required second dose of superplasticizer was
affected by two major parameters, which were water-cement ratio
and paste content, where lower water-cement ratio and paste content
cause an increase in require second dose of superplasticizer. The
amount of second dose of superplasticizer is higher as the solid
content within the system is increase, solid can be either from cement
particles or aggregate. The data was analyzed to form an equation use
to estimate the amount of second dosage requirement of
superplasticizer to recovery slump to its original.
Abstract: Escherichia coli (E. coli) is the most isolated bacteria
from blood circulation of septicemic calves. Given the prevalence of
septicemia in animals and its economic importance in veterinary
practice, better understanding of changes in clinical signs following
disease, may contribute to early detection of disorder. The present
study has been carried out to detect changes of clinical signs in
induced sepsis in calves with E. coli. Colisepticemia has been
induced in 10 twenty-day old healthy Holstein- Frisian calves with
intravenous injection of 1.5 X 109 colony forming units (cfu) of
O111:H8 strain of E. coli. Clinical signs including rectal temperature,
heart rate, respiratory rate, shock, appetite, sucking reflex, feces
consistency, general behavior, dehydration and standing ability were
recorded in experimental calves during 24 hours after induction of
colisepticemia. Blood culture was also carried out from calves four
times during experiment. ANOVA with repeated measure is used to
see changes of calves’ clinical signs to experimental colisepticemia,
and values of P≤ 0.05 was considered statistically significant. Mean
values of rectal temperature and heart rate as well as median values
of respiratory rate, appetite, suckling reflex, standing ability and feces
consistency of experimental calves increased significantly during
study (P 0.05). The
results of present study showed that total score of clinical signs in
calves with experimental colisepticemia increased significantly,
although score of some clinical signs such as shock did not change
significantly.
Abstract: To evaluate the effect of intramuscular administration
of vitamin A in pregnant dairy cows during late stages of pregnancy,
on vitamin A status of neonatal calves, a total of 30 cows were
randomly selected and divided into three groups; two treatment
groups and one control group. Single intramuscular injection of
2000000 IU vitamin A; was carried in 10 dairy cows at 7 months of
pregnancy (group 1). In second group of treated animals (10 cows)
the injection was performed in 8 months of pregnancy (group 2). Ten
pregnant dairy cows were received saline injection as placebo and
selected as control group. Blood samples were collected from
experimental dairy cows at 7 and 8 months of pregnancy as well as
their newborn calves’ pre and after colostrum intake. There was no
significant difference between vitamin A and β-carotene
concentration of dairy cows of three groups in two last months of
pregnancy (P> 0.05). Vitamin A concentration of calves of two
treatment groups before and after receiving of colostrum were
significantly higher than that in control group (P< 0.05). There was
no significant difference between serum concentrations of vitamin A
in calves of two treated groups (P> 0.05). β-Carotene concentration
of serum samples of dairy cows and neonatal calves of three groups
were not significantly different as compared with together. From
results of the present study it can be concluded that single injection of
vitamin A during at 7 or 8 month of pregnancy can significantly
increase level of vitamin A in their colostrum and neonatal calves.
Abstract: Large quantities of solid wastes being generated
worldwide from sources such as household, domestic, industrial,
commercial and construction demolition activities, leads to
environmental concerns. Utilization of these wastes in making
building construction materials can reduce the magnitude of the
associated problems. When these waste products are used in place of
other conventional materials, natural resources and energy are
preserved and expensive and/or potentially harmful waste disposal is
avoided. Recycling which is regarded as the third most preferred waste
disposal option, with its numerous environmental benefits, stand as a
viable option to offset the environmental impact associated with the
construction industry. This paper reviews the results of laboratory tests and important
research findings, and the potential of using these wastes in building
construction materials with focus on sustainable development.
Research gaps, which includes; the need to develop standard mix
design for solid waste based building materials; the need to develop
energy efficient method of processing solid waste use in concrete; the
need to study the actual behavior or performance of such building
materials in practical application and the limited real life application
of such building materials have also been identified. A research is being proposed to develop an environmentally
friendly, lightweight building block from recycled waste paper,
without the use of cement, and with properties suitable for use as
walling unit. This proposed research intends to incorporate,
laboratory experimentation and modeling to address the identified
research gaps.
Abstract: Microcantilevers are the basic MEMS devices, which
can be used as sensors, actuators and electronics can be easily built
into them. The detection principle of microcantilever sensors is based
on the measurement of change in cantilever deflection or change in its
resonance frequency. The objective of this work is to explore the
analogies between mechanical and electrical equivalent of
microcantilever beams. Normally scientists and engineers working in
MEMS use expensive software like CoventorWare, IntelliSuite,
ANSYS/Multiphysics etc. This paper indicates the need of developing
electrical equivalent of the MEMS structure and with that, one can
have a better insight on important parameters, and their interrelation of
the MEMS structure. In this work, considering the mechanical model
of microcantilever, equivalent electrical circuit is drawn and using
force-voltage analogy, it is analyzed with circuit simulation software.
By doing so, one can gain access to powerful set of intellectual tools
that have been developed for understanding electrical circuits Later
the analysis is performed using ANSYS/Multiphysics - software based
on finite element method (FEM). It is observed that both mechanical
and electrical domain results for a rectangular microcantlevers are in
agreement with each other.
Abstract: Geopolymer composites reinforced with flax fabrics
and nanoclay are fabricated and studied for physical and mechanical
properties using X-Ray Diffraction (XRD), Fourier Transform
Infrared Spectroscopy (FTIR), and Scanning Electron Microscope
(SEM). Nanoclay platelets at a weight of 1.0%, 2.0%, and 3.0% were
added to geopolymer pastes. Nanoclay at 2.0 wt.% was found to
improve density and decrease porosity while improving flexural
strength and post-peak toughness. A microstructural analysis
indicated that nanoclay behaves as filler and as an activator
supporting geopolymeric reaction while producing a higher content
geopolymer gel improving the microstructure of binders. The process
enhances adhesion between the geopolymer matrix and flax fibres.
Abstract: Both steady and unsteady turbulent mixed convection
heat transfer in a 3D lid-driven enclosure, which has constant heat
flux on the middle of bottom wall and with isothermal moving
sidewalls, is reported in this paper for working fluid with Prandtl
number Pr = 0.71. The other walls are adiabatic and stationary. The
dimensionless parameters used in this research are Reynolds number,
Re = 5000, 10000 and 15000, and Richardson number, Ri = 1 and 10.
The simulations have been done by using different turbulent methods
such as RANS, URANS, and LES. The effects of using different k-ε
models such as standard, RNG and Realizable k-ε model are
investigated. Interesting behaviours of the thermal and flow fields
with changing the Re or Ri numbers are observed. Isotherm and
turbulent kinetic energy distributions and variation of local Nusselt
number at the hot bottom wall are studied as well. The local Nusselt
number is found increasing with increasing either Re or Ri number.
In addition, the turbulent kinetic energy is discernibly affected by
increasing Re number. Moreover, the LES results have shown good
ability of this method in predicting more detailed flow structures in
the cavity.
Abstract: In the past years electric mobility became part of a
public discussion. The trend to fully electrified vehicles instead of
vehicles fueled with fossil energy has notably gained momentum.
Today nearly every big car manufacturer produces and sells fully
electrified vehicles, but electrified vehicles are still not as competitive
as conventional powered vehicles. As the traction battery states the
largest cost driver, lowering its price is a crucial objective. In
addition to improvements in product and production processes a nonnegligible,
but widely underestimated cost driver of production can
be found in logistics, since the production technology is not
continuous yet and neither are the logistics systems. This paper presents an approach to evaluate cost factors on
different designs of load carrier systems. Due to numerous
interdependencies, the combination of costs factors for a particular
scenario is not transparent. This is effecting actions for cost reduction
negatively, but still cost reduction is one of the major goals for
simultaneous engineering processes. Therefore a concurrent and
phase appropriate cost valuation method is necessary to serve cost
transparency. In this paper the four phases of this cost valuation
method are defined and explained, which based upon a new approach
integrating the logistics development process in to the integrated
product and process development.
Abstract: The aim of this paper is to propose a general
framework for storing, analyzing, and extracting knowledge from
two-dimensional echocardiographic images, color Doppler images,
non-medical images, and general data sets. A number of high
performance data mining algorithms have been used to carry out this
task. Our framework encompasses four layers namely physical
storage, object identification, knowledge discovery, user level.
Techniques such as active contour model to identify the cardiac
chambers, pixel classification to segment the color Doppler echo
image, universal model for image retrieval, Bayesian method for
classification, parallel algorithms for image segmentation, etc., were
employed. Using the feature vector database that have been
efficiently constructed, one can perform various data mining tasks
like clustering, classification, etc. with efficient algorithms along
with image mining given a query image. All these facilities are
included in the framework that is supported by state-of-the-art user
interface (UI). The algorithms were tested with actual patient data
and Coral image database and the results show that their performance
is better than the results reported already.
Abstract: Laura Island, which is located about 50 km away from
downtown, is a source of water supply in Majuro atoll, which is the
capital of the Republic of the Marshall Islands. Low and flat Majuro
atoll has neither river nor lake. It is very important for Majuro atoll to
ensure the conservation of its water resources. However, upconing,
which is the process of partial rising of the freshwater-saltwater
boundary near the water-supply well, was caused by the excess
pumping from it during the severe drought in 1998. Upconing will
make the water usage of the freshwater lens difficult. Thus,
appropriate water usage is required to prevent up coning in the
freshwater lens because there is no other water source during drought. Numerical simulation of water usage applying SEAWAT model
was conducted at the central part of Laura Island, including the water
supply well, which was affected by upconing. The freshwater lens was
created as a result of infiltration of consistent average rainfall. The lens
shape was almost the same as the one in 1985. 0 of monthly rainfall
and variable daily pump discharge were used to calculate the
sustainable pump discharge from the water supply well. Consequently,
the total amount of pump discharge was increased as the daily pump
discharge was increased, indicating that it needs more time to recover
from upconing. Thus, a pump standard to reduce the pump intensity is
being proposed, which is based on numerical simulation concerning
the occurrence of the up-coning phenomenon in Laura Island during
the drought.
Abstract: Frozen shrimp industry plays an important role in the
development of production industry of the country. There has been a
continuing development to response the increasing demand; however,
there have been some problems in running the enterprises. The
purposes of this study are to: 1) investigate problems related to basic
factors in operating frozen shrimp industry based on the
entrepreneurs’ points of view. The enterprises involved in this study
were small and medium industry receiving Thai Frozen Foods
Association. 2) Compare the problems of the frozen shrimp industry
according to their sizes of operation in 3 provinces of the central
region Thailand. Population in this study consisted of 148 managers
from 148 frozen shrimp enterprises Thai Frozen Foods Association
which 77 were small size and 71 were medium size. The data were
analyzed to find percentage, arithmetic mean, standard deviation, and
independent sample T-test with the significant hypothesis at .05. The
results revealed that the problems of the frozen shrimp industries of
both size were in high level. The needs for government supporting
were in high level. The comparison of the problems and the basic
factors between the small and medium size enterprises showed no
statistically significant level. The problems that they mentioned
included raw materials, labors, production, marketing, and the need
for academic supporting from the government sector.
Abstract: This study investigates how the site specific traffic
data differs from the Mechanistic Empirical Pavement Design
Software default values. Two Weigh-in-Motion (WIM) stations were
installed in Interstate-40 (I-40) and Interstate-25 (I-25) to developed
site specific data. A computer program named WIM Data Analysis
Software (WIMDAS) was developed using Microsoft C-Sharp (.Net)
for quality checking and processing of raw WIM data. A complete
year data from November 2013 to October 2014 was analyzed using
the developed WIM Data Analysis Program. After that, the vehicle
class distribution, directional distribution, lane distribution, monthly
adjustment factor, hourly distribution, axle load spectra, average
number of axle per vehicle, axle spacing, lateral wander distribution,
and wheelbase distribution were calculated. Then a comparative
study was done between measured data and AASHTOWare default
values. It was found that the measured general traffic inputs for I-40
and I-25 significantly differ from the default values.
Abstract: The Haussmannization plan of Cairo in 1867 formed a
regular network of roundabout spaces, though deteriorated at present.
The method of identifying the spatial structure of roundabout Cairo
for conservation matches the voronoi diagram with the space syntax
through their geometrical property of spatial convexity. In this
initiative, the primary convex hull of first-order voronoi adopts the
integral and control measurements of space syntax on Cairo’s
roundabout generators. The functional essence of royal palaces
optimizes the roundabout structure in terms of spatial measurements
and the symbolic voronoi projection of 'Tahrir Roundabout' over the
Giza Nile and Pyramids. Some roundabouts of major public and
commercial landmarks surround the pole of 'Ezbekia Garden' with a
higher control than integral measurements, which filter the new
spatial structure from the adjacent traditional town. Nevertheless, the
least integral and control measures correspond to the voronoi
contents of pollutant workshops and the plateau of old Cairo Citadel
with the visual compensation of new royal landmarks on top.
Meanwhile, the extended suburbs of infinite voronoi polygons
arrange high control generators of chateaux housing in 'garden city'
environs. The point pattern of roundabouts determines the
geometrical characteristics of voronoi polygons. The measured
lengths of voronoi edges alternate between the zoned short range at
the new poles of Cairo and the distributed structure of longer range.
Nevertheless, the shortest range of generator-vertex geometry
concentrates at 'Ezbekia Garden' where the crossways of vast Cairo
intersect, which maximizes the variety of choice at different spatial
resolutions. However, the symbolic 'Hippodrome' which is the largest
public landmark forms exclusive geometrical measurements, while
structuring a most integrative roundabout to parallel the royal syntax.
Overview of the symbolic convex hull of voronoi with space syntax
interconnects Parisian Cairo with the spatial chronology of scattered
monuments to conceive one universal Cairo structure. Accordingly,
the approached methodology of 'voronoi-syntax' prospects the future
conservation of roundabout Cairo at the inferred city-level concept.
Abstract: Coal fly ash, an industrial by product of coal
combustion thermal power plants is considered as a hazardous
material and its improper disposal has become an environmental
issue. On the other hand, manufacturing conventional clay bricks
involves on consumption of large amount of clay and leads
substantial depletion of topsoil. This paper unveils the possibility of
using fly ash as a partial replacement of clay for brick manufacturing
considering the local technology practiced in Bangladesh. The effect
of fly ash with different replacing ratio (0%, 20%, 30%, 40%, and
50% by volume) of clay on properties of bricks was studied. Bricks
were made in the field parallel to ordinary bricks marked with
specific number for different percentage to identify them at time of
testing. No physical distortion is observed in fly ash brick after
burning in the kiln. Results from laboratory test show that
compressive strength of brick is decreased with the increase of fly
ash and maximum compressive strength is found to be 19.6 MPa at
20% of fly ash. In addition, water absorption of fly ash brick is
increased with the increase of fly ash. The abrasion value and
Specific gravity of coarse aggregate prepared from brick with fly ash
also studied and the results of this study suggests that 20% fly ash
can be considered as the optimum fly ash content for producing good
quality bricks utilizing present practiced technology.
Abstract: The article deals with the personality of military
professionals (commanders) and their way of leading and
commanding today and in historical context. The first part focuses on
the leadership skills of Alexander the Great, who introduced strategic
innovations and even from today's perspective; he excelled in
efficient work with people. This paper focuses on the way which he
achieved his goals. Further attention is paid to approaches to
commander´s personality by other great generals. The paper is also
focused on personality traits of military professionals necessary for
successful management and leadership in today's variable and
challenging environment. Finally, attention is paid to the effective
and ineffective ways of behavior of commanders and determining
what styles of leadership is appropriate for a given situation, whether
in peacetime or on deployment.
Abstract: Financial literacy is a widely discussed topic on the
national and international level by governments, organizations and
academia. For this reason, this study analyses financial knowledge,
financial behavior, and financial attitudes of students of finance. The
aim of the paper is to determine whether the financial literacy of
university students studying finance differs from the level of financial
literacy in selected OECD countries. The research was conducted at
Masaryk University in the Czech Republic. The empirical study
comprises questions related to several aspects of financial literacy,
such as financial knowledge, personal finance behavior, or decisionmaking.
The results indicate that improvement in financial literacy of
university students is still required, even though their major is finance
related.
Abstract: Agricultural machinery industry plays an important
role in the industrial development especially the production industry
of the country. There has been continuing development responding to
the higher demand of the production. However, the problem in
agricultural machinery production still exists. Thus, the purpose of
this research is to investigate problems on fundamental factors of
industry based on the entrepreneurs’ point of view. The focus was on
the small and medium size industry receiving factory license type
number 0660 from the Department of Industrial Works. The
investigation was on the comparison between the management of the
small and medium size agricultural industry in 3 provinces in the
central region of Thailand. Population in this study consisted of 189
company managers or managing directors, of which 101 were from
the small size and 88 were from the medium size industry. The data
were analyzed to find percentage, arithmetic mean, and standard
deviation with independent sample T-test at the statistical
significance .05. The results showed that the small and medium size
agricultural machinery manufacturers in the central region of
Thailand reported high problems in every aspect. When compared the
problems on basic factors in running the business, it was found that
there was no statistically difference at .05 in managing of the small
and medium size agricultural machinery manufacturers. However,
there was a statistically significant difference between the small and
medium size agricultural machinery manufacturers on the aspect of
policy and services of the government. The problems reported by the
small and medium size agricultural machinery manufacturers were
the services on public tap water and the problem on politic and
stability of the country.
Abstract: The ASEAN Economic Community (AEC) is the goal
of regional economic integration by 2015. In the region, tourism is an
activity that is important, especially as a source of foreign currency, a
source of employment creation and a source of income bringing to the
region. Given the complexity of the issues entailing the concept of
sustainable tourism, this paper tries to assess tourism sustainability
with the ASEAN, based on a number of quantitative indicators for all
the ten economies, Thailand, Myanmar, Laos, Vietnam, Malaysia,
Singapore, Indonesia, Philippines, Cambodia, and Brunei. The
methodological framework will provide a number of benchmarks of
tourism activities in these countries. They include identification of the
dimensions; for example, economic, socio-ecologic, infrastructure
and indicators, method of scaling, chart representation and evaluation
on Asian countries. This specification shows that a similar level of
tourism activity might introduce different implementation in the
tourism activity and might have different consequences for the socioecological
environment and sustainability. The heterogeneity of
developing countries exposed briefly here would be useful to detect
and prepare for coping with the main problems of each country in
their tourism activities, as well as competitiveness and value creation
of tourism for ASEAN economic community, and will compare with
other parts of the world.
Abstract: Job satisfaction and motivation have been given an
important attention in psychology because they are seen as main
instruments in maintaining organizational growth and development;
they are also used to accomplish organizational aims and objectives.
However, it has been observed that some institutions failed in
motivating and stimulating their workers; in contrast, workers may be
motivated but not satisfied with the job and failed to perform
efficiently and effectively. It is hoped that the study of this nature
would be of significance value to all stakeholders in education
specifically, lecturers in higher institutions in Nigeria. Also, it is
hoped that the findings of this study will enhance lecturers’
effectiveness and performance in discharging their duties. In the light
of the above statements, this study investigated whether job
satisfaction and motivation predict lecturers’ effectiveness in Nigeria
Police Academy, Wudil, Kano State. Correlational research method
was adopted for the study, while purposive sampling technique was
used to choose the institution and the sampled lectures (70). Simple
random sampling technique was used to select one hundred cadets
across the academy. Two instruments were used to elicit information
from both lecturers and cadets. These were job satisfaction and
motivation; and lecturers’ effectiveness Questionnaires. The
instruments were subjected to pilot testing and found to have
reliability coefficient of 0.69 and 0.71 respectively. The results of the
study revealed that there was a significance relationship among job
satisfaction, motivation and lecturers effectiveness in Nigeria Police
Academy. There was a significance relationship between job
satisfaction and lecturers’ effectiveness in Nigeria Police Academy
the cal r is 0.21 while the crt r is 0.19. at p