Abstract: The purpose of this study is to investigate the
efficiency of a double-layer roof in collecting solar energy as an
application to the areas such as raising high-end temperature of
organic Rankine cycle (ORC). The by-product of the solar roof is to
reduce building air-conditioning loads. The experimental apparatus
are arranged to evaluate the effects of the solar roof in absorbing solar
energy. The flow channel is basically formed by an aluminum plate on
top of a plywood plate. The geometric configurations in which the
effects of absorbing energy is analyzed include: a bare uncovered
aluminum plate, a glass-covered aluminum plate, a
glass-covered/black-painted aluminum plate, a plate with variable
lengths, a flow channel with stuffed material (in an attempt on
enhancement of heat conduction), and a flow channel with variable
slanted angles. The experimental results show that the efficiency of
energy collection varies from 0.6 % to 11 % for the geometric
configurations mentioned above. An additional study is carried out
using CFD simulation to investigate the effects of fins on the
aluminum plate. It shows that due to vastly enhanced heat conduction,
the efficiency can reach ~23 % if 50 fins are installed on the aluminum
plate. The study shows that a double-layer roof can efficiently absorb
solar energy and substantially reduce building air-conditioning
loads. On the high end of an organic Rankine cycle, a solar pond is
used to replace the warm surface water of the sea as OTEC (ocean
thermal energy conversion) is the driving energy for the ORC. The
energy collected from the double-layered solar roof can be pumped
into the pond and raise the pond temperature as the pond surface area is
equivalently increased by nearly one-fourth of the total area of the
double-layer solar roof. The effect of raising solar pond temperature is
especially prominent if the double-layer solar roofs are installed in a
community area.
Abstract: This study investigates a voltage-controllable liquid crystals lens with a Fresnel zone electrode. When applying a proper voltage on the liquid crystal cell, a Fresnel-zone-distributed electric field is induced to direct liquid crystals aligned in a concentric structure. Owing to the concentrically aligned liquid crystals, a Fresnel lens is formed. We probe the Fresnel liquid crystal lens using a polarized incident beam with a wavelength of 632.8 nm, finding that the diffraction efficiency depends on the applying voltage. A remarkable diffraction efficiency of ~39.5 % is measured at the voltage of 0.9V. Additionally, a dual focus lens is fabricated by attaching a plane-convex lens to the Fresnel liquid crystals cell. The Fresnel LC lens and the dual focus lens may be applied for DVD/CD pick-up head, confocal microscopy system, or electrically-controlling optical systems.
Abstract: Ranong province has the best kaolin, and it is the most
useful of all the clay types used in ceramic making. Until recently,
there has been only one community business making ceramics in
Ranong province. And this business could not build the mix of body
and glaze from their raw material without assistance. Considering
these problems, this research is aimed to test the composition of
ceramic body and glaze which suit. Kaolin from Ranong is the raw
material which these search focuses on. All other raw materials use in
the investigation will come from southern Thailand, kaolin and
limestone from Ranong province, ball clay from Surat Thani
province, white sand from Songkhla province, and feldspar from
Nakhon Si Thammarat province. Results can be used to develop the
efficiency of industrial production which in return will enhance the
business process.
Abstract: In this paper the performance of unified power flow
controller is investigated in controlling the flow of po wer over the
transmission line. Voltage sources model is utilized to study the
behaviour of the UPFC in regulating the active, reactive power and
voltage profile. This model is incorporated in Newton Raphson
algorithm for load flow studies. Simultaneous method is employed
in which equations of UPFC and the power balance equations of
network are combined in to one set of non-linear algebraic equations.
It is solved according to the Newton raphson algorithm. Case studies
are carried on standard 5 bus network. Simulation is done in Matlab.
The result of network with and without using UPFC are compared in
terms of active and reactive power flows in the line and active and
reactive power flows at the bus to analyze the performance of UPFC.
Abstract: Artificial atoms are growing fields of interest due to their physical and optoelectronicapplications. The absorption spectra of the proposed artificial atom inpresence of Tera-Hertz field is investigated theoretically. We use the non-perturbativeFloquet theory and finite difference method to study the electronic structure of ArtificialAtom. The effect of static electric field on the energy levels of artificial atom is studied.The effect of orientation of static electric field on energy levels and diploe matrix elementsis also highlighted.
Abstract: The pressure drag from a cam shaped tube in cross flows have been investigated experimentally using pressure distribution measurement. The range of angle of attack and Reynolds number based on an equivalent circular tube are within 0≤α≤360° and 2×104< Reeq < 3.4 ×104, respectively. It is found that the pressure drag coefficient is at its highest at α=90° and 270° over the whole range of Reynolds number. Results show that the pressure drag coefficient of the cam shaped tube is lower than that of circular tube with the same surface area for more of the angles of attack. Furthermore, effects of the diameter ratio and finite length of the cam shaped tube upon the pressure drag coefficient are discussed.
Abstract: Analytical investigation of the free vibration behavior
of circular functionally graded (FG) plates integrated with two
uniformly distributed actuator layers made of piezoelectric (PZT4)
material on the top and bottom surfaces of the circular FG plate
based on the classical plate theory (CPT) is presented in this paper.
The material properties of the functionally graded substrate plate are
assumed to be graded in the thickness direction according to the
power-law distribution in terms of the volume fractions of the
constituents and the distribution of electric potential field along the
thickness direction of piezoelectric layers is simulated by a quadratic
function. The differential equations of motion are solved analytically
for clamped edge boundary condition of the plate. The detailed
mathematical derivations are presented and Numerical investigations
are performed for FG plates with two surface-bonded piezoelectric
layers. Emphasis is placed on investigating the effect of varying the
gradient index of FG plate on the free vibration characteristics of the
structure. The results are verified by those obtained from threedimensional
finite element analyses.
Abstract: The objective of the present investigation was to
evaluate the morphology of Escherchia coli bacteria in interaction
with SiO2 nanoparticles.
This study was made by atomic force microscopy and quartz
crystal microbalance using SiO2 nanoparticles with 10nm, 50nm and
100nm diameter and bacteria immobilized on polyelectrolyte
multilayer films obtained by spin coating or by “layer by layer”
(LbL) method.
Abstract: System testing is actually done to the entire system
against the Functional Requirement Specification and/or the System
Requirement Specification. Moreover, it is an investigatory testing
phase, where the focus is to have almost a destructive attitude and
test not only the design, but also the behavior and even the believed
expectations of the customer. It is also intended to test up to and
beyond the bounds defined in the software/hardware requirements
specifications. In Motorola®, Automated Testing is one of the testing
methodologies uses by GSG-iSGT (Global Software Group - iDEN
TM
Subcriber Group-Test) to increase the testing volume, productivity
and reduce test cycle-time in iDEN
TM
phones testing. Testing is able
to produce more robust products before release to the market. In this
paper, iHopper is proposed as a tool to perform stress test on iDEN
TM
phonse. We will discuss the value that automation has brought to
iDEN
TM
Phone testing such as improving software quality in the
iDEN
TM
phone together with some metrics. We will also look into
the advantages of the proposed system and some discussion of the
future work as well.
Abstract: In this paper, we are concerned with the design and
its simulation studies of a modified extremum seeking control for
nonlinear systems. A standard extremum seeking control has a simple
structure, but it takes a long time to reach an optimal operating point.
We consider a modification of the standard extremum seeking control
which is aimed to reach the optimal operating point more speedily
than the standard one. In the modification, PD acceleration term
is added before an integrator making a principal control, so that it
enables the objects to be regulated to the optimal point smoothly. This
proposed method is applied to Monod and Williams-Otto models to
investigate its effectiveness. Numerical simulation results show that
this modified method can improve the time response to the optimal
operating point more speedily than the standard one.
Abstract: The field research was carried out at the Látókép AGTC KIT research area of the University of Debrecen in Eastern-Hungary, on the area of the aeolain loess of the Hajdúság. We examined the effects of the sowing time on the phytopathogenic characteristics and yield production by applying various fertilizer treatments on two different sunflower genotypes (NK Ferti, PR64H42) in 2012 and 2013. We applied three different sowing times (early, optimal, late) and two different treatment levels of fungicides (control = no fungicides applied, double fungicide protection).
During our investigations, the studied cropyears were of different sowing time optimum in terms of yield amount (2012: early, 2013: average). By Pearson’s correlation analysis, we have found that delaying the sowing time pronouncedly decreased the extent of infection in both crop years (Diaporthe: r=0.663**, r=0.681**, Sclerotinia: r=0.465**, r=0.622**). The fungicide treatment not only decreased the extent of infection, but had yield increasing effect too (2012: r=0.498**, 2013: r=0.603**). In 2012, delaying of the sowing time increased (r=0.600**), but in 2013, it decreased (r= 0.356*) the yield amount.
Abstract: In this paper, we have focused on study of swelling kinetics and salt-sensitivity behavior of a superabsorbing hydrogel based on carboxymethylcellulose (CMC) and acrylic acid and 2- Buthyl methacrylate. The swelling kinetics of the hydrogels with various particle sizes was preliminary investigated as well. The swelling of the hydrogel showed a second order kinetics of swelling in water. In addition, swelling measurements of the synthesized hydrogels in various chloride salt solutions was measured. Results indicated that a swelling-loss with an increase in the ionic strength of the salt solutions.
Abstract: Improvement in CAE methods has an important role for shortening of the vehicle product development time. It is provided that validation of the design and improvements in terms of durability can be done without hardware prototype production. In recent years, several different methods have been developed in order to investigate fatigue damage of the vehicle. The intended goal among these methods is prediction of fatigue damage in a short time with reduced costs. This study developed a new fatigue damage prediction method in the automotive sector using power spectrum densities of accelerations. This study also confirmed that the weak region in vehicle can be easily detected with the method developed in this study which results were compared with conventional method.
Abstract: With rapid technology scaling, the proportion of the
static power consumption catches up with dynamic power
consumption gradually. To decrease leakage consumption is
becoming more and more important in low-power design. This paper
presents a power-gating scheme for P-DTGAL (p-type dual
transmission gate adiabatic logic) circuits to reduce leakage power
dissipations under deep submicron process. The energy dissipations of
P-DTGAL circuits with power-gating scheme are investigated in
different processes, frequencies and active ratios. BSIM4 model is
adopted to reflect the characteristics of the leakage currents. HSPICE
simulations show that the leakage loss is greatly reduced by using the
P-DTGAL with power-gating techniques.
Abstract: Flow movement in unsaturated soil can be expressed
by a partial differential equation, named Richards equation. The
objective of this study is the finding of an appropriate implicit
numerical solution for head based Richards equation. Some of the
well known finite difference schemes (fully implicit, Crank Nicolson
and Runge-Kutta) have been utilized in this study. In addition, the
effects of different approximations of moisture capacity function,
convergence criteria and time stepping methods were evaluated. Two
different infiltration problems were solved to investigate the
performance of different schemes. These problems include of vertical
water flow in a wet and very dry soils. The numerical solutions of
two problems were compared using four evaluation criteria and the
results of comparisons showed that fully implicit scheme is better
than the other schemes. In addition, utilizing of standard chord slope
method for approximation of moisture capacity function, automatic
time stepping method and difference between two successive
iterations as convergence criterion in the fully implicit scheme can
lead to better and more reliable results for simulation of fluid
movement in different unsaturated soils.
Abstract: We constructed a method of phase unwrapping for a typical wave-front by utilizing the maximizer of the posterior marginal (MPM) estimate corresponding to equilibrium statistical mechanics of the three-state Ising model on a square lattice on the basis of an analogy between statistical mechanics and Bayesian inference. We investigated the static properties of an MPM estimate from a phase diagram using Monte Carlo simulation for a typical wave-front with synthetic aperture radar (SAR) interferometry. The simulations clarified that the surface-consistency conditions were useful for extending the phase where the MPM estimate was successful in phase unwrapping with a high degree of accuracy and that introducing prior information into the MPM estimate also made it possible to extend the phase under the constraint of the surface-consistency conditions with a high degree of accuracy. We also found that the MPM estimate could be used to reconstruct the original wave-fronts more smoothly, if we appropriately tuned hyper-parameters corresponding to temperature to utilize fluctuations around the MAP solution. Also, from the viewpoint of statistical mechanics of the Q-Ising model, we found that the MPM estimate was regarded as a method for searching the ground state by utilizing thermal fluctuations under the constraint of the surface-consistency condition.
Abstract: Does open ended creative technology give positive impact in learning design? Although there are many researchers had examined on the impact of technology on design education but there are very few conclusive researches done on the impact of open ended used of software to learning design. This paper sought to investigate a group of student-s experience on relatively wider range of software application within the context of design project. A typography design project was used to create a learning environment with the aim of inculcate design skills into the learners and increase their creative problem-solving and critical thinking skills. The methods used in this study were questionnaire survey and personal observation which will be focus on the individual and group response during the completion of the task.
Abstract: In this work, bending fatigue life of notched
specimens with various notch geometries and dimensions is
investigated by experiment and Manson-Caffin theoretical method. In
this theoretical method, fatigue life of notched specimens is
calculated using the fatigue life obtained from the experiments for
plain specimens (without notch). Three notch geometries including
∪-shape, ∨-shape and C -shape notches are considered in this
investigation. The experiments are conducted on a rotary bending
Moore machine. The specimens are made of a low carbon steel alloy,
which has wide application in industry. The stress- life curves are
captured for all notched specimen by experiment. The results indicate
that Manson-Caffin analytical method cannot adequately predict
the fatigue life of notched specimen. However, it seems that the
difference between the experiments and Manson-Caffin predictions
can be compensated by a proportional factor.
Abstract: The purpose of this research is: a) to investigate how
the HR practices influence psychological contracts, b) to examine the
influence of psychological contracts to individual behavior and to
contribute individually, c) to study the psychological contact through
leadership. This research using mixed methods, qualitative and
quantitative research methods were utilized to gather the data
collected using a qualitative method by the HR Manager who is in
charge of the trainings from the staffs and quantitative method
(survey) by using questionnaire was utilized to draw upon and to
elaborate on the recurring themes present during the interviews. The
survey was done to 400 staffs of the company. The study found that
leadership styles supporting the firm’s HR strategy is the key in
making psychological contracts that benefit both the firm and its
members.
Abstract: In this paper we improve the quasilinearization method by barycentric Lagrange interpolation because of its numerical stability and computation speed to achieve a stable semi analytical solution. Then we applied the improved method for solving the Fin problem which is a nonlinear equation that occurs in the heat transferring. In the quasilinearization approach the nonlinear differential equation is treated by approximating the nonlinear terms by a sequence of linear expressions. The modified QLM is iterative but not perturbative and gives stable semi analytical solutions to nonlinear problems without depending on the existence of a smallness parameter. Comparison with some numerical solutions shows that the present solution is applicable.