Abstract: In this study, photocatalytic degradation of phenol by
titanium dioxide (TiO2) in aqueous solution was evaluated. The UV
energy of solar light was utilized by compound parabolic collectors
(CPCs) technology. The effect of irradiation time, initial pH, and
dosage of TiO2 were investigated. Aromatic intermediates (catechol,
benzoquinone, and hydroquinone) were quantified during the reaction
to study the pathways of the oxidation process. 94.5% degradation
efficiency of phenol was achieved after 150 minutes of irradiation
when the initial concentration was 100 mg/L. The dosage of TiO2
significantly affected the degradation efficiency of phenol. The
observed optimum pH for the reaction was 5.2. Phenol photocatalytic
degradation fitted to the pseudo-first order kinetic according to
Langmuir–Hinshelwood model.
Abstract: This paper presents the results of an experimental
study on the effects of elevated temperature on compressive and
flexural strength of Normal Strength Concrete (NSC), High Strength
Concrete (HSC) and High Performance Concrete (HPC). In addition,
the specimen mass and volume were measured before and after
heating in order to determine the loss of mass and volume during the
test. In terms of non-destructive measurement, ultrasonic pulse
velocity test was proposed as a promising initial inspection method
for fire damaged concrete structure. 100 Cube specimens for three
grades of concrete were prepared and heated at a rate of 3°C/min up
to different temperatures (150, 250, 400, 600, and 900°C). The results
show a loss of compressive and flexural strength for all the concretes
heated to temperature exceeding 400°C. The results also revealed that
mass and density of the specimen significantly reduced with an
increase in temperature.
Abstract: Numerical study of heat transfer and fluid flow over vertical double forward facing step were presented. The k-w model with finite volume method was employed to solve continuity, momentum, and energy equations. Different step heights were adopted for range of Reynolds number varied from 10000 to 40000, and range of temperature varied from 310K to 340 K. The straight side of duct is insulated while the side of double forward facing step is heated. The result shows augmentation of heat transfer due to the recirculation region created after and before steps. Effect of step length and Reynolds number observed on increase of local Nusselt number particularly at recirculation regions. Contour of streamline velocity is plotted to show recirculation regions after and before steps. Numerical simulation in this paper done by used ANSYS FLUENT 14.
Abstract: Heat transfer and laminar fluid flow over backward facing step with and without obstacle numerically studied in this paper. The finite volume method adopted to solve continuity, momentum and energy equations in two dimensions. Backward facing step without obstacle and with different dimension of obstacle were presented. The step height and expansion ratio of channel were 4.8mm and 2 respectively, the range of Reynolds number varied from 75 to 225, constant heat flux subjected on downstream of wall was 2000W/m2, and length of obstacle was 1.5, 3, and 4.5mm with width 1.5mm. The separation length noticed increase with increase Reynolds number and height of obstacle. The result shows increase of heat transfer coefficient for backward facing step with obstacle in compared to those without obstacle. The maximum enhancement of heat transfer observed at 4.5mm of height obstacle due to increase recirculation flow after the obstacle in addition that at backward. Streamline of velocity showing the increase of recirculation region with used obstacle in compared without obstacle and highest recirculation region observed at obstacle height 4.5mm. The amount of enhancement heat transfer was varied between 3-5% compared to backward without obstacle.
Abstract: Analyzing classroom assessments is one of the responsibilities of the teacher. It aims improving teacher’s instruction and assessment as well as student learning. The present study investigated factors that might explain variation in teachers’ practices regarding analysis of classroom assessments. The factors considered in the investigation included gender, in-service assessment training, teaching load, teaching experience, knowledge in assessment, attitude towards quantitative aspects of assessment, and self-perceived competence in analyzing assessments. Participants were 246 in-service teachers in Oman. Results of a stepwise multiple linear regression analysis revealed that self-perceived competence was the only significant factor explaining the variance in teachers’ analysis of assessments. Implications for research and practice are discussed.
Abstract: The results of the study on the project evaluation to
develop the competencies, capabilities, and skills in repairing
computers of people in Jompluak Local Municipality, Bang Khonthi
District, Samut Songkram Province showed that the overall result
was good (4.33). When considering on each aspect, it was found that
the highest one was on process evaluation (4.60) followed by product
evaluation (4.50) and the least one was on feeding factor (3.97).
When considering in details, it was found that: 1) the context aspect
was high (4.23) with the highest item on the arrangement of the
training situation (4.67) followed by the appropriateness of the target
(4.30) and the least aspect was on the project cooperation (3.73). 2)
The evaluation of average overall primary factor or feeding factor
showed high value (4.23) while the highest aspect was on the
capability of the trainers (4.47) followed by the suitable venue (4.33)
while the least aspect was on the insufficient budget (3.47). 3) The
average result of process evaluation was very high (4.60). The
highest aspect was on the follow-op supervision (4.70) followed by
responsibility of each project staffs (4.50) while the least aspect was
on the present situation and the problems of the community (4.40). 4)
The overall result of the product evaluation was very high (4.50). The
highest aspect was on the diversity of the activities and the
community integration (4.67) followed by project target achievement
(4.63) while the least aspect was on continuation and regularity of the
activities (4.33). The trainees reported high satisfaction on the project
management at very high level (43.33%) while 40% reported high
level and 16.67% reported moderate level. Suggestions for the project
were on the additional number of the computer sets (37.78%)
followed by longer training period especially on computer skills
(43.48%).
Abstract: Steam reforming is industrially important as it is
incorporated in several major chemical processes including the
production of ammonia, methanol, hydrogen and ox alcohols. Due to
the strongly endothermic nature of the process, a large amount of heat
is supplied by fuel burning (commonly natural gas) in the furnace
chamber. Reaction conversions, tube catalyst life, energy
consumption and CO2 emission represent the principal factors
affecting the performance of this unit and are directly influenced by
the high operating temperatures and pressures.
This study presents a simulation of the performance of the
reforming of methane in a primary reformer, through a developed
empirical relation which enables to investigate the effects of
operating parameters such as the pressure, temperature, steam to
carbon ratio on the production of hydrogen, as well as the fraction of
non converted methane.
It appears from this analysis that the exit temperature Te, the
operating pressure as well the steam to carbon ratio has an important
effect on the reforming of methane.
Abstract: The two primary objectives of this research were (1)
to examine the current knowledge and actual circumstance of
agricultural workers about mangosteen product processing; and (2) to
analyze and evaluate ways to develop capacity of mangosteen
product processing. The population of this study was 15,125 people
who work in the agricultural sector, in this context, mangosteen
production, in the eastern part of Thailand that included Chantaburi
Province, Rayong Province, Trad Province and Pracheenburi
Province. The sample size based on Yamane’s calculation with 95%
reliability was therefore 392 samples. Mixed method was employed
included questionnaire and focus group discussion with
Connoisseurship Model used in order to collect quantitative and
qualitative data. Key informants were used in the focus group
including agricultural business owners, academic people in agro food
processing, local academics, local community development staff,
OTOP subcommittee, and representatives of agro processing
industry professional organizations. The study found that the
majority of the respondents agreed with a high level (in five- rating
scale) towards most of variables of knowledge management in agro
food processing. The result of the current knowledge and actual
circumstance of agricultural human resource in an arena of
mangosteen product processing revealed that mostly, the respondents
agreed at a high level to establish 7 variables. The guideline to
developing the body of knowledge in order to enhance the capacity
of the agricultural workers in mangosteen product processing was
delivered in the focus group discussion. The discussion finally
contributed to an idea to produce manuals for mangosteen product
processing methods, with 4 products chosen: (1) mangosteen soap;
(2) mangosteen juice; (3) mangosteen toffee; and (4) mangosteen
preserves or jam.
Abstract: Mangabeira (Hancornia speciosa Gomes), a native plant in Brazil, is found growing spontaneously in various regions of the country. The high perishability of tropical fruits such as mangaba, causes it to be necessary to use technologies that promote conservation, aiming to increase the shelf life of this fruit and add value. The objective of this study was to compare the mangabas lyophilization curves behaviors with different sizes and maturation stages. The fruits were freeze-dried for a period of approximately 45 hours at lyophilizer Liotop brand, model L -108. It has been considered large the fruits between 38 and 58 mm diameter and small, between 23 and 28 mm diameter and the two states of maturation, intermediate and mature. Large size mangabas drying curves in both states of maturation were linear behavior at all process, while the kinetic drying curves related to small fruits, independent of maturation state, had a typical behavior of drying, with all the well-defined steps. With these results it was noted that the time of lyophilization was suitable for small mangabas, a fact that did not happen with the larger one. This may indicate that the large mangabas require a longer time to freeze until reaches the equilibrium level, as it happens with the small fruits, going to have constant moisture at the end of the process. For both types of fruit were analyzed water activity, acidity, protein, lipid, and vitamin C before and after the process.
Abstract: Patients under health treatments that involve long
stays at a hospital or health center (e.g. cancer, organ transplants and
severe burns), tend to get bored or depressed because of the lack of
social interaction with family and friends. Such a situation also
affects the evolution and effectiveness of their treatments. In many
cases, the solution to this problem involves extra challenges, since
many patients need to rest quietly (or remain in bed) to their being
contagious. Considering the weak health condition in which usually
are these kinds, keeping them motivated and quiet represents an
important challenge for nurses and caregivers. This article presents a
mobile ubiquitous game called MagicRace, which allows hospitalized
kinds to interact socially with one another without putting to risk
their sensitive health conditions. The game does not require a
communication infrastructure at the hospital, but instead, it uses a
mobile ad hoc network composed of the handheld devices used by
the kids to play. The usability and performance of this application
was tested in two different sessions. The preliminary results show
that users experienced positive feelings from this experience.
Abstract: The pipe taper thread measurement and uncertainty
normally used the four-wire probe according to the JIS B 0262.
Besides, according to the EA-10/10 standard, the pipe thread could be
measured using the three-wire probe. This research proposed to use
the three-wire probe measuring the pitch diameter of the pipe taper
thread. The measuring accessory component was designed and made,
then, assembled to one side of the ULM 828 CiM machine.
Therefore, this machine could be used to measure and calibrate both
the pipe thread and the pipe taper thread. The equations and the
expanded uncertainty for pitch diameter measurement were
formulated. After the experiment, the results showed that the pipe
taper thread had the pitch diameter equal to 19.165mm and the
expanded uncertainty equal to 1.88µm. Then, the experiment results
were compared to the results from the National Institute of Metrology
Thailand. The equivalence ratio from the comparison showed that
both results were related. Thus, the proposed method of using the
three-wire probe measured the pitch diameter of the pipe taper thread
was acceptable.
Abstract: Several meteorological parameters were used for the
prediction of monthly average daily global solar radiation on
horizontal using recurrent neural networks (RNNs). Climatological
data and measures, mainly air temperature, humidity, sunshine
duration, and wind speed between 1995 and 2007 were used to design
and validate a feed forward and recurrent neural network based
prediction systems. In this paper we present our reference system
based on a feed-forward multilayer perceptron (MLP) as well as the
proposed approach based on an RNN model. The obtained results
were promising and comparable to those obtained by other existing
empirical and neural models. The experimental results showed the
advantage of RNNs over simple MLPs when we deal with time series
solar radiation predictions based on daily climatological data.
Abstract: Industries using conventional fossil fuels have an
interest in better understanding the mechanism of particulate
formation during combustion since such is responsible for emission
of undesired inorganic elements that directly impact the atmospheric
pollution level. Fine and ultrafine particulates have tendency to
escape the flue gas cleaning devices to the atmosphere. They also
preferentially collect on surfaces in power systems resulting in
ascending in corrosion inclination, descending in the heat transfer
thermal unit, and severe impact on human health. This adverseness
manifests particularly in the regions of world where coal is the
dominated source of energy for consumption.
This study highlights the behavior of calcium transformation as
mineral grains verses organically associated inorganic components
during pulverized coal combustion. The influence of existing type of
calcium on the coarse, fine and ultrafine mode formation mechanisms
is also presented. The impact of two sub-bituminous coals on particle
size and calcium composition evolution during combustion is to be
assessed. Three mixed blends named Blends 1, 2, and 3 are selected
according to the ration of coal A to coal B by weight. Calcium
percentage in original coal increases as going from Blend 1 to 3.
A mathematical model and a new approach of describing
constituent distribution are proposed. Analysis of experiments of
calcium distribution in ash is also modeled using Poisson distribution.
A novel parameter, called elemental index λ, is introduced as a
measuring factor of element distribution.
Results show that calcium in ash that originally in coal as mineral
grains has index of 17, whereas organically associated calcium
transformed to fly ash shown to be best described when elemental
index λ is 7.
As an alkaline-earth element, calcium is considered the
fundamental element responsible for boiler deficiency since it is the
major player in the mechanism of ash slagging process. The
mechanism of particle size distribution and mineral species of ash
particles are presented using CCSEM and size-segregated ash
characteristics. Conclusions are drawn from the analysis of
pulverized coal ash generated from a utility-scale boiler.
Abstract: Urban road dust comprises of a range of potentially
toxic metal elements and plays a critical role in degrading urban
receiving water quality. Hence, assessing the metal composition and
concentration in urban road dust is a high priority. This study
investigated the variability of metal composition and concentrations
in road dust in 4 different urban land uses in Gold Coast, Australia.
Samples from 16 road sites were collected and tested for selected 12
metal species. The data set was analyzed using both univariate and
multivariate techniques. Outcomes of the data analysis revealed that
the metal concentrations inroad dust differs considerably within and
between different land uses. Iron, aluminum, magnesium and zinc are
the most abundant in urban land uses. It was also noted that metal
species such as titanium, nickel, copper and zinc have the highest
concentrations in industrial land use. The study outcomes revealed
that soil and traffic related sources as key sources of metals deposited
on road surfaces.
Abstract: This paper explains the results of an investigation on the analysis of flush end plate steel connections by means of finite element method. Flush end plates are a highly indeterminate type of connection, which have a number of parameters that affect their behavior. Because of this, experimental investigations are complicated and very costly. Today, the finite element method provides an ideal method for analyzing complicated structures. Finite element models of these types of connections under monotonic loading have previously been investigated. A numerical model, which can predict the cyclic behavior of these connections, is of critical importance, as dynamic experiments are more costly. This paper summarizes a study to develop a three-dimensional finite element model that can accurately capture the cyclic behavior of flush end plate connections. Comparisons between FEM results and experimental results obtained from full-scale tests have been carried out, which confirms the accuracy of the finite element model. Consequently, design equations for this connection have been investigated and it is shown that these predictions are not precise in all cases. The effect of end plate thickness and bolt diameter on the overall behavior of this connection is discussed. This research demonstrates that using the appropriate configuration, this connection has the potential to form a plastic hinge in the beam--desirable in seismic behavior.
Abstract: The Proton Exchange Membranes (PEM) are largely studied because they operate at low temperatures and they are suitable for mobile applications. However, there are some deficiencies in their operation, mainly those that use ethanol as a hydrogen source, that require a certain attention. Therefore, this research aimed to develop Nafion® composite membranes, mixing clay minerals, kaolin and halloysite to the polymer matrix in order to improve the ethanol molecule retentions and, at the same time, to keep the system’s protonic conductivity. The modified Nafion/Kaolin, Nafion/Halloysite composite membranes were prepared in weight proportion of 0.5, 1.0 and 1.5. The membranes obtained were characterized as to their ethanol permeability, protonic conductivity and water absorption. The composite morphology and structure are characterized by SEM and EDX and the thermal behavior is determined by TGA and DSC. The analysis of the results shows ethanol permeability reduction from 48% to 63%. However, the protonic conductivity results are lower in relation to pure Nafion®. As to the thermal behavior, the Nafion® composite membranes were stable up to a temperature of 325ºC.
Abstract: Fluoroquinolones are a group of antibiotics widely used because of their broad spectrum activity against both Gram-positive and Gram-negative bacteria. In this study, ciprofloxacin and levofloxacin were administered to rats at therapeutic doses to evaluate their effects on plasma arylesterase activity, as well as, on hepatic advanced oxidized protein products (AOPPs) and malondialdehyde (MDA) levels, as measures of oxidative stress. Ciprofloxacin (80 mg/kg body weight) and levofloxacin (40 mg/kg body weight) were administered to male albino rats for 7 and 14 days. The data obtained demonstrated that plasma arylesterase activity was significantly decreased by both drugs with ciprofloxacin administration inhibiting the activity by 29% and 30% while Levofloxacin treatment resulted in 35% and 30% inhibition, after 7 and 14 days treatment respectively. Hepatic AOPP and MDA levels were both elevated by these antibiotics. This study supplies further evidence that fluoroquinolones at therapeutic doses promote oxidative stress.
Abstract: This paper proposes a hierarchical hidden Markov model (HHMM) to model the detection of M vehicles in a wireless sensor network (WSN). The HHMM model contains an extra level of hidden Markov model to model the temporal transitions of each
state of the first HMM. By modeling the temporal transitions, only those hypothesis with nonzero transition probabilities needs to be tested. Thus, this method efficiently reduces the computation load, which is preferable in WSN applications.This paper integrates several techniques to optimize the detection performance. The output of the states of the first HMM is modeled as Gaussian Mixture Model (GMM), where the number of states and the number of Gaussians are experimentally determined, while the other parameters are estimated using Expectation Maximization (EM). HHMM is used to model the sequence of the local decisions which are based on multiple hypothesis testing with maximum likelihood approach. The states in the HHMM represent various combinations of vehicles of different types. Due to the statistical advantages of multisensor data fusion, we propose a heuristic based on fuzzy weighted majority voting to enhance cooperative classification of moving vehicles within a region that is monitored by a wireless sensor network. A fuzzy inference system weighs each local decision based on the signal to noise
ratio of the acoustic signal for target detection and the signal to noise ratio of the radio signal for sensor communication. The spatial correlation among the observations of neighboring sensor nodes is efficiently utilized as well as the temporal correlation. Simulation results demonstrate the efficiency of this scheme.
Abstract: Since, both the relative position of tunnels and the construction procedure affect the soil movement and internal forces in the lining, it is of major concern to study the influence of these factors on the tunnel design. Construction procedures of tunnels have considerable effects on the magnitude of surface movements and lining stresses. This paper describes numerical analysis of construction procedure of a three adjacent shallow tunnels at high groundwater levels using the commercial finite difference software (FLAC-3D). The aim of this study is to determinate the most suitable construction procedure for the three tunnels and the optimum excavation step in Tehran Metro tunnels in order to optimize the surface settlements and lining stresses.
Abstract: Implementing of a continues flow gas lift system for one vertical oil well producer in Wafa field was investigated under five reservoir pressures and their dependent parameters. Well 03 producers were responded positively to the gas lift system despite of the high well head operating pressures. However, the flowing bottom hole pressures were reduced by a ratio from 6 to 33 % in the case A3 for example, for the design runs conducted under the existing operating conditions for years 2003, 2006 and 2009. This reduction in FBHP has increased the production rate by a ratio from 12 to 22.5%. The results indicated that continues flow gas lift system is a good candidate as an artificial lift system to be considered for the one vertical producer covered by this study. Most significantly, timing for artificial lift by a gas lift system for this field is highly dependent on the amount of gas available at the time of implementation because of the high gas production rate from the top of the reservoir.