Abstract: Collection of storm water runoff and forcing it into the
groundwater is the need of the hour to sustain the ground water table.
However, the runoff entraps various types of sediments and other
floating objects whose removal are essential to avoid pollution of
ground water and blocking of pores of aquifer. However, it requires
regular cleaning and maintenance due to problem of clogging. To
evaluate the performance of filter system consisting of coarse sand
(CS), gravel (G) and pebble (P) layers, a laboratory experiment was
conducted in a rectangular column. The effect of variable thickness
of CS, G and P layers of the filtration unit of the recharge shaft on the
recharge rate and the sediment concentration of effluent water were
evaluated.
Medium sand (MS) of three particle sizes, viz. 0.150–0.300 mm
(T1), 0.300–0.425 mm (T2) and 0.425–0.600 mm of thickness 25 cm,
30 cm and 35 cm respectively in the top layer of the filter system and
having seven influent sediment concentrations of 250–3,000 mg/l
were used for experimental study. The performance was evaluated in
terms of recharge rates and clogging time. The results indicated that
100 % suspended solids were entrapped in the upper 10 cm layer of
MS, the recharge rates declined sharply for influent concentrations of
more than 1,000 mg/l. All treatments with higher thickness of MS
media indicated recharge rate slightly more than that of all treatment
with lower thickness of MS media respectively. The performance of
storm water infiltration systems was highly dependent on the
formation of a clogging layer at the filter. An empirical relationship
has been derived between recharge rates, inflow sediment load, size
of MS and thickness of MS with using MLR.
Abstract: The temperature dependence of wettability (wetting
angle, Θ (T)) for Ag-based melts on graphite and Al2O3 substrates is
compared. Typical alloying effects are found, as the Ag host metal is
gradually replaced by various metallic elements. The essence of
alloying lies in the change of the electron/atom (e/a) ratio. This ratio
is also manifested in the shift of wetting angles on the same substrate.
Nevertheless, the effects are partially smeared by other
(metallurgical) factors, like the interaction between the oxygenalloying
elements and by the graphite substrate-oxygen interaction. In
contrast, such effects are not pronounced in the case of Al2O3
substrates. As a consequence, Θ(T) exhibits an opposite trend in the
case of two substrates. Crossovers of the Θ(T) curves were often
found. The positions of crossovers depend on the chemical character
and concentration of solute atoms. Segregation and epitaxial texture
formation after solidification were also observed in certain alloy
drops, especially in high concentration range. This phenomenon is
not yet explained in every detail.
Abstract: The dielectric properties and ionic conductivity of
novel "ceramic state" polymer electrolytes for high capacity lithium
battery are characterized by Radio frequency and Microwave
methods in two broad frequency ranges from 50 Hz to 20 KHz and 4
GHz to 40 GHz. This innovative solid polymer electrolyte which is
highly ionic conductive (10-3 S/cm at room temperature) from -40oC
to +150oC can be used in any battery application. Such polymer
exhibits properties more like a ceramic rather than polymer. The
various applied measurement methods produced accurate dielectric
results for comprehensive analysis of electrochemical properties and
ion transportation mechanism of this newly invented polymer
electrolyte. Two techniques and instruments employing air gap
measurement by Capacitance Bridge and in-waveguide measurement
by vector network analyzer are applied to measure the complex
dielectric spectra. The complex dielectric spectra are used to
determine the complex alternating current electrical conductivity and
thus the ionic conductivity.
Abstract: The industrial process adds to engineering wood
products features absent in solid wood, with homogeneous structure
and reduced defects, improved physical and mechanical properties,
bio-deterioration, resistance and better dimensional stability,
improving quality and increasing the reliability of structures wood.
These features combined with using fast-growing trees, make them
environmentally ecological products, ensuring a strong consumer
market. The wood I-joists are manufactured by the industrial profiles
bonding flange and web, an important aspect of the production of
wooden I-beams is the adhesive joint that bonds the web to the
flange. Adhesives can effectively transfer and distribute stresses,
thereby increasing the strength and stiffness of the composite. The
objective of this study is to evaluate different resins in a shear strain
specimens with the aim of analyzing the most efficient resin and
possibility of using national products, reducing the manufacturing
cost. First was conducted a literature review, where established the
geometry and materials generally used, then established and analyzed
8 national resins and produced six specimens for each.
Abstract: A collection of thirty cultivars/clones of a red pitaya
was used to investigate flowering response to lighting
supplementation in the winter season of 2013-2014 in southern
Taiwan. The night-breaking treatment was conducted during the
period of 10 Oct. 2013 to 5 Mar. 2014 with 4-continuous hours
(22.00 – 02.00 hrs) of additional lighting daily using incandescent
bulbs (100W). Among cultivars and clones tested, twenty-three
genotypes, most belonging to the red-magenta flesh type, were found
to have positively flowering response to the lighting treatment. The
duration of night-breaking treatment for successful flowering
initiation varied from 33- 48 days. The lighting-sensitive genotypes
bore 1-2 flowering flushes. Floral and fruiting stages took 21-26 and
46-59 days, respectively. Among sixteen fruiting genotypes, the
highest fruit set rates were found in Damao 9, D4, D13, Chaozou
large, Chaozhou 5, Small Nick and F22. Five cultivars and clones
(Orejona, D4, Chaozhou large, Chaozhou 5 and Small Nick) produced
fruits with an average weight of more than 300 g per fruit which were
higher than those of the fruits formed in the summer of 2013. Fruits
produced during off-season containing total soluble solids (TSS)
from 17.5 to 20.7oBrix, which were higher than those produced inseason.
Abstract: This study is concerned with the optimization of
fermentation parameters for the hyper production of mannanase from
Fusarium oxysporum SS-25 employing two step statistical strategy
and kinetic characterization of crude enzyme preparation. The
Plackett-Burman design used to screen out the important factors in
the culture medium revealed 20% (w/w) wheat bran, 2% (w/w) each
of potato peels, soyabean meal and malt extract, 1% tryptone, 0.14%
NH4SO4, 0.2% KH2PO4, 0.0002% ZnSO4, 0.0005% FeSO4, 0.01%
MnSO4, 0.012% SDS, 0.03% NH4Cl, 0.1% NaNO3 in brewer’s spent
grain based medium with 50% moisture content, inoculated with
2.8×107 spores and incubated at 30oC for 6 days to be the main
parameters influencing the enzyme production. Of these factors, four
variables including soyabean meal, FeSO4, MnSO4 and NaNO3 were
chosen to study the interactive effects and their optimum levels in
central composite design of response surface methodology with the
final mannanase yield of 193 IU/gds. The kinetic characterization
revealed the crude enzyme to be active over broader temperature and
pH range. This could result in 26.6% reduction in kappa number with
4.93% higher tear index and 1% increase in brightness when used to
treat the wheat straw based kraft pulp. The hydrolytic potential of
enzyme was also demonstrated on both locust bean gum and guar
gum.
Abstract: The increasing demand of gallium, indium and
rare-earth elements for the production of electronics, e.g. solid
state-lighting, photovoltaics, integrated circuits, and liquid crystal
displays, will exceed the world-wide supply according to current
forecasts. Recycling systems to reclaim these materials are not yet in
place, which challenges the sustainability of these technologies. This
paper proposes a multispectral imaging system as a basis for a vision
based recognition system for valuable components of electronics
waste. Multispectral images intend to enhance the contrast of images
of printed circuit boards (single components, as well as labels) for
further analysis, such as optical character recognition and entire
printed circuit board recognition. The results show, that a higher
contrast is achieved in the near infrared compared to ultraviolett and
visible light.
Abstract: The current study investigated the influence of milling
time and ball-to-powder (BPR) weight ratio on the microstructural
constituents and mechanical properties of bulk nanocrystalline Al;
Al-10%Cu; and Al-10%Cu-5%Ti alloys. Powder consolidation was
carried out using a high frequency induction heat sintering where the
processed metal powders were sintered into a dense and strong bulk
material. The powders and the bulk samples were characterized using
XRD and FEGSEM techniques. The mechanical properties were
evaluated at various temperatures of 25°C, 100°C, 200°C, 300°C and
400°C to study the thermal stability of the processed alloys. The
processed bulk nanocrystalline alloys displayed extremely high
hardness values even at elevated temperatures. The Al-10%Cu-5%Ti
alloy displayed the highest hardness values at room and elevated
temperatures which are related to the presence of Ti-containing
phases such as Al3Ti and AlCu2Ti. These phases are thermally stable
and retain the high hardness values at elevated temperatures up to
400ºC.
Abstract: Equal channel angular pressing (ECAP) of
commercial Al-Mg-Si alloy was conducted using two strain rates.
The ECAP processing was conducted at room temperature and at
250°C. Route A was adopted up to a total number of four passes in
the present work. Structural evolution of the aluminum alloy discs
was investigated before and after ECAP processing using optical
microscopy (OM). Following ECAP, simple compression tests and
Vicker’s hardness were performed. OM micrographs showed that, the
average grain size of the as-received Al-Mg-Si disc tends to be larger
than the size of the ECAP processed discs. Moreover, significant
difference in the grain morphologies of the as-received and processed
discs was observed. Intensity of deformation was observed via the
alignment of the Al-Mg-Si consolidated particles (grains) in the
direction of shear, which increased with increasing the number of
passes via ECAP. Increasing the number of passes up to 4 resulted in
increasing the grains aspect ratio up to ~5. It was found that the
pressing temperature has a significant influence on the
microstructure, Hv-values, and compressive strength of the processed
discs. Hardness measurements demonstrated that 1-pass resulted in
increase of Hv-value by 42% compared to that of the as-received
alloy. 4-passes of ECAP processing resulted in additional increase in
the Hv-value. A similar trend was observed for the yield and
compressive strength. Experimental data of the Hv-values
demonstrated that there is a lack of any significant dependence on the
processing strain rate.
Abstract: Risperidone (RISP) is an antipsychotic agent and has
low water solubility and nontargeted delivery results in numerous
side effects. Hence, an attempt was made to develop SLNs hydrogel
for intranasal delivery of RISP to achieve maximum bioavailability
and reduction of side effects. RISP loaded SLNs composed of 1.65%
(w/v) lipid mass were produced by high shear homogenization (HSH)
coupled ultrasound (US) method using glycerylmonostearate (GMS)
or Imwitor 900K (solid lipid). The particles were loaded with 0.2%
(w/v) of the RISP & surface-tailored with a 2.02% (w/v) non-ionic
surfactant Tween® 80. Optimization was done using 32 factorial
design using Design Expert® software. The prepared SLNs
dispersion incorporated into Polycarbophil AA1 hydrogel (0.5%
w/v). The final gel formulation was evaluated for entrapment
efficiency, particle size, rheological properties, X ray diffraction, in
vitro diffusion, ex vivo permeation using sheep nasal mucosa and
histopathological studies for nasocilliary toxicity. The entrapment
efficiency of optimized SLNs was found to be 76 ± 2%,
polydispersity index
Abstract: Laser beam welding of dissimilar sheet metal
combinations such as Ti/Al, SS/Al and Cu/Al are increasingly
demanded due to high energy densities with less fusion and heat
affected zones. A good weld joint strength involves combinations of
dissimilar metals and the formation of solid solution in the weld pool.
Many metal pairs suffer from significant intermetallic phase
formation during welding which greatly reduces their strength. The
three different sheet metal mentioned above is critically reviewed and
phase diagram for the combinations are given. The aim of this study
is to develop an efficient metal combinations and the influence on
their interfacial characteristics. For that the following parameters
such as weld geometry, residual distortion, micro hardness,
microstructure and mechanical properties are analyzed
systematically.
Abstract: A strain of Monascus purpureus CMU001 was used to
prepare red yeast rice from Thai glutinous rice Korkor 6 (RD 6).
Adding of different amounts of histidine (156, 312, 625 and 1250 mg
in 100 g of rice grains)) under aerobic and air limitation (air-lock)
condition were used in solid fermentation. Determination of the yield
as well as monacolin K content was done. Citrinin content was also
determined in order to confirm the safety use of prepared red yeast
rice. It was found that under air-lock condition with 1250 mg of
histidine addition gave the highest yield of 37.40 g of dried red yeast
rice prepared from 100 g of rice. Highest 5.72 mg content of
monacolin K was obtained under air-lock condition with 312 mg
histidine addition. In the other hand, citrinin content was found to be
less than 24462 ng/g of all dried red yeast rice samples under the
experimental methods used in this work.
Abstract: The thermal conductivity of a fluid can be
significantly enhanced by dispersing nano-sized particles in it, and
the resultant fluid is termed as "nanofluid". A theoretical model for
estimating the thermal conductivity of a nanofluid has been proposed
here. It is based on the mechanism that evenly dispersed
nanoparticles within a nanofluid undergo Brownian motion in course
of which the nanoparticles repeatedly collide with the heat source.
During each collision a rapid heat transfer occurs owing to the solidsolid
contact. Molecular dynamics (MD) simulation of the collision
of nanoparticles with the heat source has shown that there is a pulselike
pick up of heat by the nanoparticles within 20-100 ps, the extent
of which depends not only on thermal conductivity of the
nanoparticles, but also on the elastic and other physical properties of
the nanoparticle. After the collision the nanoparticles undergo
Brownian motion in the base fluid and release the excess heat to the
surrounding base fluid within 2-10 ms. The Brownian motion and
associated temperature variation of the nanoparticles have been
modeled by stochastic analysis. Repeated occurrence of these events
by the suspended nanoparticles significantly contributes to the
characteristic thermal conductivity of the nanofluids, which has been
estimated by the present model for a ethylene glycol based nanofluid
containing Cu-nanoparticles of size ranging from 8 to 20 nm, with
Gaussian size distribution. The prediction of the present model has
shown a reasonable agreement with the experimental data available
in literature.
Abstract: In this study, we are interested in a species of the
family of Asteraceae (Tagetes erecta). This family is considered as a
source of antimicrobial extracts with strong capacity. The extraction
of the flavonoids is carried out by the method of liquid/liquid with the
use of successive solvents. Afterwards, we evaluated the biological
activity of the flavonoids on five pathogenic bacterial stocks such as
Escherichia coli, Bacillus subtilis, Klebsiella pneumoniae,
Pseudomonas aeruginosa and Staphylococcus aureus and two stocks
of yeasts to knowing Candida albicans) and Saccharomyces
cerevisiae, by employing the method of the aromatogramme starting
from a solid disc. The result of the antimicrobial activity shows an
action and a variable degree of sensitivity according to bacterial
stocks tested. It will be noted that the flavonoids have an inhibiting
effect on E. coli, B. subtilis, K. pneumoniae and S. aureus. But a
resistance with respect to the extract by P. aeruginosa, C. albicans
and S. cerevisiae is to be mentioned.
Abstract: In this research, waterglass based aerogel powder was
prepared by sol–gel process and ambient pressure drying. Inspired by
limited dust releasing, aerogel powder was introduced to the PET
electrospinning solution in an attempt to create required bulk and
surface structure for the nanofibers to improve their hydrophobic and
insulation properties. The samples evaluation was carried out by
measuring density, porosity, contact angle, heat transfer, FTIR, BET,
and SEM. According to the results, porous silica aerogel powder was
fabricated with mean pore diameter of 24 nm and contact angle of
145.9º. The results indicated the usefulness of the aerogel powder
confined into nanofibers to control surface roughness for
manipulating superhydrophobic nanowebs with water contact angle
of 147º. It can be due to a multi-scale surface roughness which was
created by nanowebs structure itself and nanofibers surface
irregularity in presence of the aerogels while a layer of fluorocarbon
created low surface energy. The wettability of a solid substrate is an
important property that is controlled by both the chemical
composition and geometry of the surface. Also, a decreasing trend in
the heat transfer was observed from 22% for the nanofibers without
any aerogel powder to 8% for the nanofibers with 4% aerogel
powder. The development of thermal insulating materials has become
increasingly more important than ever in view of the fossil energy
depletion and global warming that call for more demanding energysaving
practices.
Abstract: The tomato is a very important crop, whose
cultivation in the Mediterranean basin is severely affected by the
phytoparasitic weed Phelipanche ramosa. The semiarid regions of
the world are considered the main areas where this parasitic weed is
established causing heavy infestation as it is able to produce high
numbers of seeds (up to 500,000 per plant), which remain viable for
extended period (more than 20 years). In this paper the results
obtained from eleven treatments in order to control this parasitic
weed including chemical, agronomic, biological and biotechnological
methods compared with the untreated test under two plowing depths
(30 and 50 cm) are reported. The split-plot design with 3 replicates
was adopted. In 2014 a trial was performed in Foggia province
(southern Italy) on processing tomato (cv Docet) grown in the field
infested by Phelipanche ramosa. Tomato seedlings were transplant
on May 5, on a clay-loam soil. During the growing cycle of the
tomato crop, at 56-78 and 92 days after transplantation, the number
of parasitic shoots emerged in each plot was detected. At tomato
harvesting, on August 18, the major quantity-quality yield parameters
were determined (marketable yield, mean weight, dry matter, pH,
soluble solids and color of fruits). All data were subjected to analysis
of variance (ANOVA) and the means were compared by Tukey's test.
Each treatment studied did not provide complete control against
Phelipanche ramosa. However, among the different methods tested,
some of them which Fusarium, gliphosate, radicon biostimulant and
Red Setter tomato cv (improved genotypes obtained by Tilling
technology) under deeper plowing (50 cm depth) proved to mitigate
the virulence of the Phelipanche ramose attacks. It is assumed that
these effects can be improved combining some of these treatments
each other, especially for a gradual and continuing reduction of the
“seed bank” of the parasite in the soil.
Abstract: The study is devoted to define the optimal conditions
for the nitriding of pure iron at atmospheric pressure by using NH3-
Ar-C3H8 gas mixtures. After studying the mechanisms of phase
formation and mass transfer at the gas-solid interface, a mathematical
model is developed in order to predict the nitrogen transfer rate in the
solid, the ε-carbonitride layer growth rate and the nitrogen and
carbon concentration profiles. In order to validate the model and to
show its possibilities, it is compared with thermogravimetric
experiments, analyses and metallurgical observations (X-ray
diffraction, optical microscopy and electron microprobe analysis).
Results obtained allow us to demonstrate the sound correlation
between the experimental results and the theoretical predictions.
Abstract: This paper discusses the role of music as a ludic
activity and constituent element of voice in the construction and
consolidation of the relationship of the baby and his/her mother or
caretaker, evaluating its implications in his/her psychic structure and
constitution as a subject. The work was based on the research
developed as part of the author’s doctoral activities carried out from
her insertion in a project of the Music Department of Federal
University of Rio Grande do Sul - UFRGS, which objective was the
development of musical activities with groups of babies from 0 to 24
months old and their caretakers. Observations, video recordings of
the meetings, audio testemonies, and evaluation tools applied to
group participants were used as instruments for this research.
Information was collected on the participation of 195 babies, among
which 8 were more focused on through interviews with their mothers
or caretakers. These interviews were analyzed based on the
referential of French Discourse Analysis, Psychoanalysis, Psychology
of Development and Musical Education. The results of the research
were complemented by other posterior experiences that the author
developed with similar groups, in a context of a private clinic. The
information collected allowed the observation of the ludic and
structural functions of musical activities, when developed in a
structured environment, as well as the importance of the musicality of
the mother’s voice to the psychical structuring of the baby, allowing
his/her insertion in the language and his/her constitution as a subject.
Abstract: Regardless of the manufacturing process used,
subtractive or additive, material, purpose and application, produced
components are conventionally solid mass with more or less complex
shape depending on the production technology selected. Aspects
such as reducing the weight of components, associated with the low
volume of material required and the almost non-existent material
waste, speed and flexibility of production and, primarily, a high
mechanical strength combined with high structural performance, are
competitive advantages in any industrial sector, from automotive,
molds, aviation, aerospace, construction, pharmaceuticals, medicine
and more recently in human tissue engineering. Such features,
properties and functionalities are attained in metal components
produced using the additive technique of Rapid Prototyping from
metal powders commonly known as Selective Laser Melting (SLM),
with optimized internal topologies and varying densities. In order to
produce components with high strength and high structural and
functional performance, regardless of the type of application, three
different internal topologies were developed and analyzed using
numerical computational tools. The developed topologies were
numerically submitted to mechanical compression and four point
bending testing. Finite Element Analysis results demonstrate how
different internal topologies can contribute to improve mechanical
properties, even with a high degree of porosity relatively to fully
dense components. Results are very promising not only from the
point of view of mechanical resistance, but especially through the
achievement of considerable variation in density without loss of
structural and functional high performance.
Abstract: Vacuum Insulation Panel (VIP) can achieve very low
thermal conductivity by evacuating its inner space. Heat transfer in the
core materials of highly-evacuated VIP occurs by conduction through
the solid structure and radiation through the pore. The effect of various
scattering modes in combined conduction-radiation in VIP is
investigated through numerical analysis. The discrete ordinates
interpolation method (DOIM) incorporated with the commercial code
FLUENT® is employed. It is found that backward scattering is more
effective in reducing the total heat transfer while isotropic scattering is
almost identical with pure absorbing/emitting case of the same optical
thickness. For a purely scattering medium, the results agrees well with
additive solution with diffusion approximation, while a modified term
is added in the effect of optical thickness to backward scattering is
employed. For other scattering phase functions, it is also confirmed
that backwardly scattering phase function gives a lower effective
thermal conductivity. Thus the materials with backward scattering
properties, with radiation shields are desirable to lower the thermal
conductivity of VIPs.