Abstract: This paper presents the development of a single-ended 38.5 kS/s 10-bit programmable reference SAR ADC which is realized in MIMOS’s 0.35 µm CMOS process. The design uses a resistive DAC, a dynamic comparator with pre-amplifier and a SAR digital logic to create 10 effective bits ADC. A programmable reference circuitry allows the ADC to operate with different input range from 0.6 V to 2.1 V. The ADC consumed less than 7.5 mW power with a 3 V supply.
Abstract: Vertical Handover(VHO) among different
communication technologies ensuring uninterruption and service
continuity is one of the most important performance parameter in
Heterogenous networks environment. In an integrated Universal
Mobile Telecommunicatin System(UMTS) and Wireless Local
Area Network(WLAN), WLAN is given an inherent priority over
UMTS because of its high data rates with low cost. Therefore
mobile users want to be associated with WLAN maximum of the
time while roaming, to enjoy best possible services with low cost.
That encourages reduction of number of VHO. In this work the
reduction of number of VHO with respect to varying number of
WLAN Access Points(APs) in an integrated UMTS and WLAN
network is investigated through simulation to provide best possible
cost effective service to the users. The simulation has been carried
out for an area (7800 × 9006)m2 where COST-231 Hata model
and 3GPP (TR 101 112 V 3.1.0) specified models are used for
WLAN and UMTS path loss models respectively. The handover
decision is triggered based on the received signal level as compared
to the fade margin. Fade margin gives a probabilistic measure of
the reliability of the communication link. A relationship between
number of WLAN APs and the number of VHO is also established
in this work.
Abstract: In this paper, the transient device performance analysis
of n-type Gate Inside JunctionLess Transistor (GI-JLT) has been
evaluated. 3-D Bohm Quantum Potential (BQP) transport device
simulation has been used to evaluate the delay and power dissipation
performance. GI-JLT has a number of desirable device parameters
such as reduced propagation delay, dynamic power dissipation,
power and delay product, intrinsic gate delay and energy delay
product as compared to Gate-all-around transistors GAA-JLT. In
addition to this, various other device performance parameters namely,
on/off current ratio, short channel effects (SCE), transconductance
Generation Factor (TGF) and unity gain cut-off frequency (fT ) and
subthreshold slope (SS) of the GI-JLT and GAA-JLT have been
analyzed and compared. GI-JLT shows better device performance
characteristics than GAA-JLT for low power and high frequency
applications, because of its larger gate electrostatic control on the
device operation.
Abstract: Fugitive particulate matter (PM) is a major source of
airborne pollution in the Middle East countries. The meteorological
conditions and topography of the area makes it highly susceptible to
wind-blown particles which raise many air quality concerns. Air
quality tools such as field monitoring, emission factors and dispersion
modeling have been used in previous research studies to analyze the
release and impacts of fugitive PM in the region. However, these
tools have been originally developed based on experiments made for
European and North American regions. In this work, an experimental
campaign was conducted on April-May 2014 in a construction site in
Doha city, Qatar. The ultimate goal is to evaluate the applicability of
the existing emission factors for construction sites in dry and arid
areas like the Middle East.
Abstract: Welfare may be considered to be a subjective
experience; it has a biological function that is related to the fitness
and survival of the animal accordingly, researches have suggested
that welfare is compromised when the animal's evolutionary fitness is
reduced. This study was carried out to explain the effect of some
managerial stressors as handling and restraint on behavioral patterns
and biochemical parameters of rats. A total of 24 (12 males & 12
females) Sprague-Dawley rats (12 months & 150-180g) were allotted
into 3 groups, handled group (4 male & 4 female), restrained group (4
male & 4 female) and control group (4 males & 4 females).
The obtained results revealed that time spent feeding, drinking,
movement and cage exploration frequencies increased significantly in
handled rats than other groups, while lying time and licking increased
significantly in restrained rats than handled and controls. Moreover,
social behavior decreased in both stressed groups than control.
Triglycerides were significantly increased in handled rats than
other groups, while total lipid, total protein and globulin significantly
increased in both treated groups than control. Corticosterone
increased in restrained and handled rats than control ones. Moreover,
there was an increment in packed cell volume significantly in
restrained rats than others. These deducted that if we want to study
the effect of stress on animal welfare it is necessary to study the
effect of such stressors on animal’s behavior and physiological
responses.
Abstract: In view of a possible application in optical data
storage devices, diffraction grating efficiency of an organic dye, Acid
Fuchsin doped in PMMA matrix was studied under excitation with
CW diode pumped Nd: YAG laser at 532 nm. The open aperture Zscan
of dye doped polymer displayed saturable absorption and the
closed aperture Z-scan of the samples exhibited negative
nonlinearity. The diffraction efficiency of the grating is the ratio of
the intensity of the first order diffracted power to the incident read
beam power. The dye doped polymer films were found to be good
media for recording. It is observed that the formation of gratings
strongly depend on the concentration of dye in the polymer film, the
intensity ratios of the writing beams and the angle between the
writing beams. It has been found that efficient writing can be made at
an angle of 20o and when the intensity ratio of the writing beams is
unity.
Abstract: The final energy use can be divided mainly in four sectors: commercial, industrial, residential, and transportation. The trend in final energy consumption by sector plays as a most straightforward way to provide a wide indication of progress for reducing energy consumption and associated environmental impacts by different end use sectors. The average share of end use energy for residential sector in the world was nearly 20% until 2011, in Germany a higher proportion is between 25% and 30%. However, it remains less studied than energy use in other three sectors as well its impacts on climate and environment. The reason for this involves a wide range of fields, including the diversity of residential construction like different housing building design and materials, living or energy using behavioral patterns, climatic condition and variation as well other social obstacles, market trend potential and financial support from government.
This paper presents an extensive and in-depth analysis of the manner by which projects researched and operated by authors in the fields of energy efficiency primarily from the perspectives of both technical potential and initiative energy saving consciousness in the residential sectors especially in social housing buildings.
Abstract: A strain of Monascus purpureus CMU001 was used to
prepare red yeast rice from Thai glutinous rice Korkor 6 (RD 6).
Adding of different amounts of histidine (156, 312, 625 and 1250 mg
in 100 g of rice grains)) under aerobic and air limitation (air-lock)
condition were used in solid fermentation. Determination of the yield
as well as monacolin K content was done. Citrinin content was also
determined in order to confirm the safety use of prepared red yeast
rice. It was found that under air-lock condition with 1250 mg of
histidine addition gave the highest yield of 37.40 g of dried red yeast
rice prepared from 100 g of rice. Highest 5.72 mg content of
monacolin K was obtained under air-lock condition with 312 mg
histidine addition. In the other hand, citrinin content was found to be
less than 24462 ng/g of all dried red yeast rice samples under the
experimental methods used in this work.
Abstract: Wireless mesh networking is rapidly gaining in
popularity with a variety of users: from municipalities to enterprises,
from telecom service providers to public safety and military
organizations. This increasing popularity is based on two basic facts:
ease of deployment and increase in network capacity expressed in
bandwidth per footage; WMNs do not rely on any fixed
infrastructure. Many efforts have been used to maximizing
throughput of the network in a multi-channel multi-radio wireless
mesh network. Current approaches are purely based on either static or
dynamic channel allocation approaches. In this paper, we use a
hybrid multichannel multi radio wireless mesh networking
architecture, where static and dynamic interfaces are built in the
nodes. Dynamic Adaptive Channel Allocation protocol (DACA), it
considers optimization for both throughput and delay in the channel
allocation. The assignment of the channel has been allocated to be codependent
with the routing problem in the wireless mesh network and
that should be based on passage flow on every link. Temporal and
spatial relationship rises to re compute the channel assignment every
time when the pattern changes in mesh network, channel assignment
algorithms assign channels in network. In this paper a computing
path which captures the available path bandwidth is the proposed
information and the proficient routing protocol based on the new path
which provides both static and dynamic links. The consistency
property guarantees that each node makes an appropriate packet
forwarding decision and balancing the control usage of the network,
so that a data packet will traverse through the right path.
Abstract: Worldwide, most PILC MV underground cables in use
are approaching the end of their design life; hence, failures are likely
to increase. This paper studies the electric field and potential
distributions within the PILC insulted cable containing common
void-defect. The finite element model of the performance of the
belted PILC MV underground cable is presented. The variation of the
electric field stress within the cable using the Finite Element Method
(FEM) is concentrated. The effects of the void-defect within the
insulation are given. Outcomes will lead to deeper understanding of
the modeling of Paper Insulated Lead Covered (PILC) and electric
field response of belted PILC insulted cable containing void defect.
Abstract: The main aim of a communication system is to
achieve maximum performance. In Cognitive Radio any user or
transceiver has ability to sense best suitable channel, while channel is
not in use. It means an unlicensed user can share the spectrum of a
licensed user without any interference. Though, the spectrum sensing
consumes a large amount of energy and it can reduce by applying
various artificial intelligent methods for determining proper spectrum
holes. It also increases the efficiency of Cognitive Radio Network
(CRN). In this survey paper we discuss the use of different learning
models and implementation of Artificial Neural Network (ANN) to
increase the learning and decision making capacity of CRN without
affecting bandwidth, cost and signal rate.
Abstract: The purpose of this paper is to examine gas transport
behavior of mixed matrix membranes (MMMs) combined with
porous particles. Main existing models are categorized in two main
groups; two-phase (ideal contact) and three-phase (non-ideal contact).
A new coefficient, J, was obtained to express equations for estimating
effect of the particle porosity in two-phase and three-phase models.
Modified models evaluates with existing models and experimental
data using Matlab software. Comparison of gas permeability of
proposed modified models with existing models in different MMMs
shows a better prediction of gas permeability in MMMs.
Abstract: In this study, data loss tolerance of Support Vector Machines (SVM) based activity recognition model and multi activity classification performance when data are received over a lossy wireless sensor network is examined. Initially, the classification algorithm we use is evaluated in terms of resilience to random data loss with 3D acceleration sensor data for sitting, lying, walking and standing actions. The results show that the proposed classification method can recognize these activities successfully despite high data loss. Secondly, the effect of differentiated quality of service performance on activity recognition success is measured with activity data acquired from a multi hop wireless sensor network, which introduces high data loss. The effect of number of nodes on the reliability and multi activity classification success is demonstrated in simulation environment. To the best of our knowledge, the effect of data loss in a wireless sensor network on activity detection success rate of an SVM based classification algorithm has not been studied before.
Abstract: This paper presents the scaling laws that provide the
criteria of geometry and dynamic similitude between the full-size
rotor-shaft system and its scale model, and can be used to predict the
torsional vibration characteristics of the full-size rotor-shaft system by
manipulating the corresponding data of its scale model. The scaling
factors, which play fundamental roles in predicting the geometry and
dynamic relationships between the full-size rotor-shaft system and its
scale model, for torsional free vibration problems between scale and
full-size rotor-shaft systems are firstly obtained from the equation of
motion of torsional free vibration. Then, the scaling factor of external
force (i.e., torque) required for the torsional forced vibration problems
is determined based on the Newton’s second law. Numerical results
show that the torsional free and forced vibration characteristics of a
full-size rotor-shaft system can be accurately predicted from those of
its scale models by using the foregoing scaling factors. For this reason,
it is believed that the presented approach will be significant for
investigating the relevant phenomenon in the scale model tests.
Abstract: Future flood can be predicted using the probable
maximum flood (PMF). PMF is calculated using the historical
discharge or rainfall data considering the other climatic parameters
remaining stationary. However climate is changing globally and the
key climatic variables are temperature, evaporation, rainfall and sea
level rise are likely to change. To develop scenarios to a basin or
catchment scale these important climatic variables should be
considered. Nowadays scenario based on climatic variables is more
suitable than PMF. Six scenarios were developed for a large Fitzroy
basin and presented in this paper.
Abstract: Cloud computing (CC) has already gained overall
appreciation in research and practice. Whereas the willingness to
integrate cloud services in various IT environments is still unbroken,
the previous CC procurement processes run mostly in an unorganized
and non-standardized way. In practice, a sufficiently specific, yet
applicable business process for the important acquisition phase is
often lacking. And research does not appropriately remedy this
deficiency yet. Therefore, this paper introduces a field-tested
approach for CC procurement. Based on an extensive literature
review and augmented by expert interviews, we designed a model
that is validated and further refined through an in-depth real-life case
study. For the detailed process description, we apply the event-driven
process chain notation (EPC). The gained valuable insights into the
case study may help CC research to shift to a more socio-technical
area. For practice, next to giving useful organizational instructions
we will provide extended checklists and lessons learned.
Abstract: This paper proposed a silicon controller rectifier (SCR)
based ESD protection device to protect low voltage ESD for integrated
circuit. The proposed ESD protection device has low trigger voltage
and high holding voltage compared with conventional SCR-based
ESD protection devices. The proposed ESD protection circuit is
verified and compared by TCAD simulation. This paper verified
effective low voltage ESD characteristics with low trigger voltage of
5.79V and high holding voltage of 3.5V through optimization
depending on design variables (D1, D2, D3 and D4).
Abstract: In the scope of application of technical textiles, Non-
Crimp Fabrics are increasingly used. In general, NCF exhibit
excellent load bearing properties, but caused by the manufacturing
process, there are some remaining disadvantages which have to be
reduced. Regarding to this, a novel technique of processing NCF was
developed substituting the binding-thread by an adhesive. This stitchfree
method requires new manufacturing concept as well as new basic
methods to prove adhesion of glue at fibres and textiles. To improve
adhesion properties and the wettability of carbon-fibres by the
adhesive, oxy-fluorination was used. The modification of carbonfibres
by oxy-fluorination was investigated via scanning electron
microscope, X-ray photoelectron spectroscopy and single fibre
tensiometry. Special tensile tests were developed to determine the
maximum force required for detachment.
Abstract: Proof of controlling crack width is a basic condition
for securing suitable performance in serviceability limit state. The
cracking in concrete can occur at any time from the casting of time to
the years after the concrete has been set in place. Most codes struggle
with offering procedure for crack width calculation. There is lack in
availability of design charts for designers to compute crack width
with ease. The focus of the study is to utilize design charts and
parametric equations in calculating crack width with minimum error.
The paper contains a simplified procedure to calculate crack width
for reinforced concrete (RC) sections subjected to bending with axial
tensile force following the guidelines of Euro code [DS EN-1992-1-1
& DS EN-1992-1-2]. Numerical examples demonstrate the
application of the suggested procedure. Comparison with parallel
analytical tools supports the validity of result and show the
percentage deviation of crack width in both the procedures. The
technique is simple, user friendly and ready to evolve for a greater
spectrum of section sizes and materials.
Abstract: Food as perishable goods represents a specific and
sensitive part in the supply chain theory, since changing physical or
chemical characteristics considerably influence the approach to stock
management. The most delicate phase of this process is
transportation, where it becomes difficult to ensure the stable
conditions which limit deterioration, since the value of the
deterioration rate could be easily influenced by the mode of
transportation. The fuzzy definition of variables allows one to take
these variations into account. Furthermore, an appropriate choice of
the defuzzification method permits one to adapt results to real
conditions as far as possible. In this article those methods which take
into account the relationship between the deterioration rate of
perishable goods and transportation by ship will be applied with the
aim of (a) minimizing the total cost function, defined as the sum of
the ordering cost, holding cost, disposing cost and transportation
costs, and (b) improving the supply chain sustainability by reducing
environmental impact and waste disposal costs.