Abstract: A solar powered air heating system using one ended evacuated tubes is experimentally investigated. A solar air heater containing forty evacuated tubes is used for heating purpose. The collector surface area is about 4.44 m2. The length and outer diameters of the outer glass tube and absorber tube are 1500, 47 and 37 mm, respectively. In this experimental setup, we have a header (heat exchanger) of square shape (190 mm x 190 mm). The length of header is 1500 mm. The header consists of a hollow pipe in the center whose diameter is 60 mm through which the air is made to flow. The experimental setup contains approximately 108 liters of water. Water is working as heat collecting medium which collects the solar heat falling on the tubes. This heat is delivered to the air flowing through the header pipe. This heat flow is due to natural convection and conduction. The outlet air temperature depends upon several factors along with air flow rate and solar radiation intensity. The study has been done for both up-flow and down-flow of air in header in similar weather conditions, at different flow rates. In the present investigations the study has been made to find the effect of intensity of solar radiations and flow rate of air on the out let temperature of the air with time and which flow is more efficient. The obtained results show that the system is highly effective for the heating in this region. Moreover, it has been observed that system is highly efficient for the particular flow rate of air. It was also observed that downflow configuration is more effective than up-flow condition at all flow rates due to lesser losses in down-flow. The results show that temperature differences of upper head and lower head, both of water and surface of pipes on the respective ends is lower in down-flow.
Abstract: Using strength Pulse Electrical Field (PEF) in food
industries is a non-thermal process that can deactivate
microorganisms and increase penetration in plant and animals tissues
without serious impact on food taste and quality. In this paper designing and fabricating of a PEF generator has been presented. Pulse generation methods have been surveyed and the best of them
selected. The equipment by controller set can generate square pulse with adjustable parameters such as amplitude 1-5kV, frequency 0.1-10Hz, pulse width 10-100s, and duty cycle 0-100%. Setting the number of pulses, and presenting the output voltage and current
waveforms on the oscilloscope screen are another advantages of this
equipment. Finally, some food samples were tested that yielded the satisfactory results. PEF applying had considerable effects on potato, banana and purple cabbage. It caused increase Brix factor from 0.05
to 0.15 in potato solution. It is also so effective in extraction color material from purple cabbage. In the last experiment effects of PEF
voltages on color extraction of saffron scum were surveyed (about 6% increasing yield).
Abstract: The construction of original functional sample of the portable device for fast analysis of energetic materials has been described in the paper. The portable device consisting of two parts – an original miniaturized microcolumn liquid chromatograph and a unique chemiluminescence detector – has been proposed and realized. In a very short time, this portable device is capable of identifying selectively most of military nitramine- and nitroesterbased explosives as well as inorganic nitrates occurring in trace concentrations in water or in soil. The total time required for the identification of extracts is shorter than 8 minutes.
Abstract: This paper analyzes the effect of a single uniform accounting rule on reporting quality by investigating the influence of IFRS on earnings management. This paper examines whether earnings management is reduced after IFRS adoption through the use of “loss avoidance thresholds”, a method that has been verified in earlier studies. This paper concentrates on two European countries: one that represents the continental code law tradition with weak protection of investors (France) and one that represents the Anglo-American common law tradition, which typically implies a strong enforcement system (the United Kingdom).
The research investigates a sample of 526 companies (6822 firm-year observations) during the years 2000 – 2013. The results are different for the two jurisdictions. This study demonstrates that a single set of accounting standards contributes to better reporting quality and reduces the pervasiveness of earnings management in France. In contrast, there is no evidence that a reduction in earnings management followed the implementation of IFRS in the United Kingdom. Due to the fact that IFRS benefit France but not the United Kingdom, other political and economic factors, such legal system or capital market strength, must play a significant role in influencing the comparability and transparency cross-border companies’ financial statements. Overall, the result suggests that IFRS moderately contribute to the accounting quality of reported financial statements and bring benefit for stakeholders, though the role played by other economic factors cannot be discounted.
Abstract: A variety of new technology-based services have
emerged with the development of Information and Communication
Technologies (ICTs). Since technology-based services have technology-driven characteristics, the identification of relationships
between technology-based services and ICTs would give meaningful implications. Thus, this paper proposes an approach for identifying the
relationships between technology-based services and ICTs by
analyzing patent documents. First, business model (BM) patents are
classified into relevant service categories. Second, patent citation
analysis is conducted to investigate the technological linkage and impacts between technology-based services and ICTs at macro level.
Third, as a micro level analysis, patent co-classification analysis is
employed to identify the technological linkage and coverage. The
proposed approach could guide and help managers and designers of
technology-based services to discover the opportunity of the development of new technology-based services in emerging service sectors.
Abstract: A plausible architecture of an ancient genetic code is derived from an extended base triplet vector space over the Galois field of the extended base alphabet {D, G, A, U, C}, where the letter D represent one or more hypothetical bases with unspecific pairing. We hypothesized that the high degeneration of a primeval genetic code with five bases and the gradual origin and improvements of a primitive DNA repair system could make possible the transition from the ancient to the modern genetic code. Our results suggest that the Watson-Crick base pairing and the non-specific base pairing of the hypothetical ancestral base D used to define the sum and product operations are enough features to determine the coding constraints of the primeval and the modern genetic code, as well as the transition from the former to the later. Geometrical and algebraic properties of this vector space reveal that the present codon assignment of the standard genetic code could be induced from a primeval codon assignment. Besides, the Fourier spectrum of the extended DNA genome sequences derived from the multiple sequence alignment suggests that the called period-3 property of the present coding DNA sequences could also exist in the ancient coding DNA sequences.
Abstract: The past decade has seen enormous growth in the amount of software produced. However, given the ever increasing complexity of the software being developed and the concomitant rise in the typical project size, managers are becoming increasingly aware of the importance of issues that influence the productivity levels of the project teams involved. By analyzing the latest release of ISBSG data repository, we report on the factors found to significantly influence the productivity among which average team size and language type are the two most essential ones. Building on this we present an original model for evaluating the potential productivity during the project planning stage.
Abstract: Nowadays, financial and economic crises are growing
more and reach more countries and sectors. These events have, as a
result, a considerable impact on the activities of the firms which think
unstable and in danger.
But besides this heavy uncertainty which weighs on the different
firms, the family firm, object of our research, is not only confronted
with these external difficulties but also with an internal challenge and
of size: that of transmission. Indeed, the transmission of an
organization from one generation to another can succeed as it can
fail; leaving considerable damage.
Our research registers as part of these problems since we tried to
understand relation between the behavior of two main actors of the
process of succession, predecessor and successor; and the success of
transmission.
Abstract: Recently, permeable breakwaters have been suggested to overcome the disadvantages of fully protection breakwaters. These protection structures have minor impacts on the coastal environment and neighboring beaches where they provide a more economical protection from waves and currents. For regular waves, a numerical model is used (FLOW-3D, VOF) to investigate the hydraulic performance of a permeable breakwater. The model of permeable breakwater consists of a pair of identical vertical slotted walls with an impermeable upper and lower part, where the draft is a decimal multiple of the total depth. The middle part is permeable with a porosity of 50%. The second barrier is located at distant of 0.5 and 1.5 of the water depth from the first one. The numerical model is validated by comparisons with previous laboratory data and semi-analytical results of the same model. A good agreement between the numerical results and both laboratory data and semi-analytical results has been shown and the results indicate the applicability of the numerical model to reproduce most of the important features of the interaction. Through the numerical investigation, the friction factor of the model is carefully discussed.
Abstract: In this paper, Wavelet based ANFIS for finding inter
turn fault of generator is proposed. The detector uniquely responds to
the winding inter turn fault with remarkably high sensitivity.
Discrimination of different percentage of winding affected by inter
turn fault is provided via ANFIS having an Eight dimensional input
vector. This input vector is obtained from features extracted from
DWT of inter turn faulty current leaving the generator phase
winding. Training data for ANFIS are generated via a simulation of
generator with inter turn fault using MATLAB. The proposed
algorithm using ANFIS is giving satisfied performance than ANN
with selected statistical data of decomposed levels of faulty current.
Abstract: This paper summaries basic principles and concepts of
intelligent controls, implemented in humanoid robotics as well as
recent algorithms being devised for advanced control of humanoid
robots. Secondly, this paper presents a new approach neuro-fuzzy
system. We have included some simulating results from our
computational intelligence technique that will be applied to our
humanoid robot. Subsequently, we determine a relationship between
joint trajectories and located forces on robot-s foot through a
proposed neuro-fuzzy technique.
Abstract: Overloading is a technique to accommodate more
number of users than the spreading factor N. This is a bandwidth
efficient scheme to increase the number users in a fixed bandwidth.
One of the efficient schemes to overload a CDMA system is to use
two sets of orthogonal signal waveforms (O/O). The first set is
assigned to the N users and the second set is assigned to the
additional M users. An iterative interference cancellation technique is
used to cancel interference between the two sets of users. In this
paper, the performance of an overloading scheme in which the first N
users are assigned Walsh-Hadamard orthogonal codes and extra users
are assigned the same WH codes but overlaid by a fixed (quasi) bent
sequence [11] is evaluated. This particular scheme is called Quasi-
Orthogonal Sequence (QOS) O/O scheme, which is a part of
cdma2000 standard [12] to provide overloading in the downlink
using single user detector. QOS scheme are balance O/O scheme,
where the correlation between any set-1 and set-2 users are
equalized. The allowable overload of this scheme is investigated in
the uplink on an AWGN and Rayleigh fading channels, so that the
uncoded performance with iterative multistage interference
cancellation detector remains close to the single user bound. It is
shown that this scheme provides 19% and 11% overloading with
SDIC technique for N= 16 and 64 respectively, with an SNR
degradation of less than 0.35 dB as compared to single user bound at
a BER of 0.00001. But on a Rayleigh fading channel, the channel
overloading is 45% (29 extra users) at a BER of 0.0005, with an SNR
degradation of about 1 dB as compared to single user performance
for N=64. This is a significant amount of channel overloading on a
Rayleigh fading channel.
Abstract: Phytophthora cinnamomi (P. c) is a plant pathogenic
oomycete that is capable of damaging plants in commercial production
systems and natural ecosystems worldwide. The most common
methods for the detection and diagnosis of P. c infection are
expensive, elaborate and time consuming. This study was carried out
to examine whether species specific and life cycle specific volatile
organic compounds (VOCs) can be absorbed by solid-phase
microextraction fibers and detected by gas chromatography that are
produced by P. c and another oomycete Pythium dissotocum. A
headspace solid-phase microextraction (HS-SPME) together with gas
chromatography (GC) method was developed and optimized for the
identification of the VOCs released by P. c. The optimized parameters
included type of fiber, exposure time, desorption temperature and
desorption time. Optimization was achieved with the analytes of P.
c+V8A and V8A alone. To perform the HS-SPME, six types of fiber
were assayed and compared: 7μm Polydimethylsiloxane (PDMS),
100μm Polydimethylsiloxane (PDMS), 50/30μm
Divinylbenzene/CarboxenTM/Polydimethylsiloxane
DVB/CAR/PDMS), 65μm Polydimethylsiloxane/Divinylbenzene
(PDMS/DVB), 85μm Polyacrylate (PA) fibre and 85μm CarboxenTM/
Polydimethylsiloxane (Carboxen™/PDMS). In a comparison of the
efficacy of the fibers, the bipolar fiber DVB/CAR/PDMS had a higher
extraction efficiency than the other fibers. An exposure time of 16h
with DVB/CAR/PDMS fiber in the sample headspace was enough to
reach the maximum extraction efficiency. A desorption time of 3min
in the GC injector with the desorption temperature of 250°C was
enough for the fiber to desorb the compounds of interest. The chromatograms and morphology study confirmed that the VOCs from
P. c+V8A had distinct differences from V8A alone, as did different
life cycle stages of P. c and different taxa such as Pythium dissotocum.
The study proved that P. c has species and life cycle specific VOCs,
which in turn demonstrated the feasibility of this method as means of
Abstract: Aims for this study: first, to compare the expertise
level in data analysis, communication and information technologies
in undergraduate psychology students. Second, to verify the factor
structure of E-ETICA (Escala de Experticia en Tecnologias de la Informacion, la Comunicacion y el Análisis or Data Analysis,
Communication and Information'Expertise Scale) which had shown
an excellent internal consistency (α= 0.92) as well as a simple factor
structure. Three factors, Complex, Basic Information and
Communications Technologies and E-Searching and Download
Abilities, explains 63% of variance. In the present study, 260
students (119 juniors and 141 seniors) were asked to respond to
ETICA (16 items Likert scale of five points 1: null domain to 5: total
domain). The results show that both junior and senior students report
having very similar expertise level; however, E-ETICA presents a
different factor structure for juniors and four factors explained also
63% of variance: Information E-Searching, Download and Process;
Data analysis; Organization; and Communication technologies.
Abstract: This study was conducted using the data collected at the mouth of Jen-Gen River to investigate and analyze chromium (Cr) contained in the sediments, and to evaluate the accumulation of Cr and the degree of its potential risk. The results show that samples collected at all monitoring stations near the mouth of Jen-Gen River contain 92–567 mg/kg of Cr with average of 366±166 mg/kg. The spatial distribution of Cr reveals that the Cr concentration is relatively high in the river mouth region, and gradually diminishes toward the harbor region. This indicates that upstream industrial and municipal wastewater discharges along the river bank are major sources of pollution. The accumulation factor and potential ecological risk index indicate that the sedimentation at Jen-Gen River mouth has the most serious degree of Cr accumulation and the highest ecological potential risk.
Abstract: A compact tunable 10 W picosecond source based on
Yb-doped fiber amplification of gain switch laser diode has been
demonstrated. A gain switch semiconductor laser diode was used as
the seed source, and a multi-stage single mode Yb-doped fiber
preamplifier was combined with two large mode area double-clad
Yb-doped fiber main amplifiers to construct the amplification system.
The tunable pulses with high stability and excellent beam quality
(M2
Abstract: Literature review revealed the importance of the
adoption of marketing Relationship for loyalty and retaining
profitable customer (Customer Relationship Management). LPQ
satisfaction will reinforce the loyalty and customer brand
attachment. Customer will communicate the operator to others. The
focus of this study is to examine the relationship between the
LPPQ and the WOM recommendations through: customer
satisfaction, loyalty and attachment. The results show that LPQ
affect positively the satisfaction, negatively the loyalty. LPQ has an
indirectly effect on WOM recommendations but through the
satisfaction and attachment. The mediating effect of satisfaction in
the relationship between LPQ and Loyalty is rejected. This finding
can be explained by the nature of mobile sector in Tunisia.
Abstract: In this paper, a novel multipurpose audio watermarking
algorithm is proposed based on Vector Quantization (VQ) in Discrete
Cosine Transform (DCT) domain using the codeword labeling and
index-bit constrained method. By using this algorithm, it can fulfill the
requirements of both the copyright protection and content integrity
authentication at the same time for the multimedia artworks. The
robust watermark is embedded in the middle frequency coefficients of
the DCT transform during the labeled codeword vector quantization
procedure. The fragile watermark is embedded into the indices of the
high frequency coefficients of the DCT transform by using the
constrained index vector quantization method for the purpose of
integrity authentication of the original audio signals. Both the robust
and the fragile watermarks can be extracted without the original audio
signals, and the simulation results show that our algorithm is effective
with regard to the transparency, robustness and the authentication
requirements
Abstract: According to dramatic growth of internet services, an easy and prompt service deployment has been important for internet service providers to successfully maintain time-to-market. Before global service deployment, they have to pay the big cost for service evaluation to make a decision of the proper system location, system scale, service delay and so on. But, intra-Lab evaluation tends to have big gaps in the measured data compared with the realistic situation, because it is very difficult to accurately expect the local service environment, network congestion, service delay, network bandwidth and other factors. Therefore, to resolve or ease the upper problems, we propose multiple cloud based GPES Broker system and use case that helps internet service providers to alleviate the above problems in beta release phase and to make a prompt decision for their service launching. By supporting more realistic and reliable evaluation information, the proposed GPES Broker system saves the service release cost and enables internet service provider to make a prompt decision about their service launching to various remote regions.
Abstract: to simulate the phenomenon of electronic transport in semiconductors, we try to adapt a numerical method, often and most frequently it’s that of Monte Carlo. In our work, we applied this method in the case of a ternary alloy semiconductor GaInP in its cubic form; The Calculations are made using a non-parabolic effective-mass energy band model. We consider a band of conduction to three valleys (ΓLX), major of the scattering mechanisms are taken into account in this modeling, as the interactions with the acoustic phonons (elastic collisions) and optics (inelastic collisions). The polar optical phonons cause anisotropic collisions, intra-valleys, very probable in the III-V semiconductors. Other optical phonons, no polar, allow transitions inter-valleys. Initially, we present the full results obtained by the simulation of Monte Carlo in GaInP in stationary regime. We consider thereafter the effects related to the application of an electric field varying according to time, we thus study the transient phenomenon which make their appearance in ternary material