Abstract: Multiphasing of dc-dc converters has been known to give technical and economical benefits to low voltage high power buck regulator modules. A major advantage of multiphasing dc-dc converters is the improvement of input and output performances in the buck converter. From this aspect, a potential use would be in renewable energy where power quality plays an important factor. This paper presents the design of a 2-phase 200W boost converter for battery charging application. Analysis of results from hardware measurement of the boost converter demonstrates the benefits of using multiphase. Results from the hardware prototype of the 2-phase boost converter further show the potential extension of multiphase beyond its commonly used low voltage high current domains.
Abstract: Bean common mosaic necrosis virus (BCMNV) is a
potyvirus with a worldwide distribution. This virus causes serious
economic losses in Iran in many leguminoses. During 20008,
samples were collected from soybeans fields in Tehran Province.
Four isolates (S1, S2 and S3) were inoculated on 15 species of
Cucurbitaceae, Chenopodiaceae, Solanacae and Leguminosae.
Chenopodium quinoa and C. amaranticolor.
Did not developed any symptoms.all isolates caused mosaic
symptoms on Phaseolus vulgaris cv. Red Kidney and P. vulgaris cv.
Bountiful. The molecular weights of coat protein using SDS-PAGE
and western blotting were estimated at 33 kDa. Reverse transcription
polymerase chain reaction (RT-PCR) was performed using one
primer pairs designed by L. XU et al. An approximately 920 bp
fragment was amplified with a specific primer.
Abstract: Ten lactating multiparous Holstein cows were used in
a cross-over design with two dietary treatments and 28-d periods
(with 14 d as an adaptation) to study the effect of restaurant fat on
milk production and composition. Each cow was offered 14.7 kg
DM /d of the basal concentrate diet based on barley and corn (crude
protein = 17.7%, neutral detergent fiber = 23.5%, and acid detergent
fiber = 5.8% of dry matter) with free access to alfalfa. Dietary
treatments were arranged as supplying each cow with 0 (CONTROL)
or 150 g/day (RF) of restaurant fat. Supplemental RF did not
significantly (P > 0.25) affect milk yield, composition, and
composition yields, except for milk fat contents. Milk fat contents
were depressed (P < 0.05) with supplemental RF. Our results indicate
that RF could depress milk fat without affecting milk yield and that
the depression in milk fat in response to RF precedes the depression
in milk yield.
Abstract: A combination of photosynthetic bacteria along with
anaerobic acidogenic bacteria is an ideal option for efficient
hydrogen production. In the present study, the optimum
concentration of substrates for the growth of Rhodobacter
sphaeroides was found by response surface methodology. The
optimum combination of three individual fatty acids was determined
by Box Behnken design. Increase of volatile fatty acid concentration
decreased the growth. Combination of sodium acetate and sodium
propionate was most significant for the growth of the organism. The
results showed that a maximum biomass concentration of 0.916 g/l
was obtained when the concentrations of acetate, propionate and
butyrate were 0.73g/l,0.99g/l and 0.799g/l, respectively. The growth
was studied under an optimum concentration of volatile fatty acids
and at a light intensity of 3000 lux, initial pH of 7 and a temperature
of 35°C.The maximum biomass concentration of 0.92g/l was
obtained which verified the practicability of this optimization.
Abstract: When earthquakes strike the city it results in great loss of lives. The present paper talks about a new innovative design system (MegEifel) for buildings which has a mechanism to mitigate deaths in case any earthquake strikes the city. If buildings will be designed according to MegEifel design then the occupants of the building will be safe even when they are in sleep or are doing day wise activities during the time earthquake strikes. The core structure is suggested to be designed on the principle that more deep the foundations are, the harder it is to uproot the structure. The buildings will have an Eifel rod dug deep into earth which will help save lives in tall buildings when earthquake strikes. This design takes a leverage of protective shells to save lives.
Abstract: The problem of wastewater treatment in Egypt is a two-fold problem; the first part concerning the existing rural areas, the second one dealing with new industrial/domestic areas. In Egypt several agricultural projects have been initiated by the government and the private sector as well, in order to change its infrastructure. As a reliable energy source, photovoltaic pumping systems have contributed to supply water for local rural communities worldwide; they can also be implemented to solve the problem “wastewater environment pollution". The solution of this problem can be categorised as recycle process. In addition, because of regional conditions past technologies are being reexamined to select a smallscale treatment system requiring low construction and maintenance costs. This paper gives the design guidelines of a Photovoltaic Small- Scale Wastewater Treatment Plant (PVSSWTP) based on technologies that can be transferred.
Abstract: The machining performance is determined by the
frequency characteristics of the machine-tool structure and the
dynamics of the cutting process. Therefore, the prediction of dynamic
vibration behavior of spindle tool system is of great importance for the
design of a machine tool capable of high-precision and high-speed
machining. The aim of this study is to develop a finite element model
to predict the dynamic characteristics of milling machine tool and
hence evaluate the influence of the preload of the spindle bearings. To
this purpose, a three dimensional spindle bearing model of a high
speed engraving spindle tool was created. In this model, the rolling
interfaces with contact stiffness defined by Harris model were used to
simulate the spindle bearing components. Then a full finite element
model of a vertical milling machine was established by coupling the
spindle tool unit with the machine frame structure. Using this model,
the vibration mode that had a dominant influence on the dynamic
stiffness was determined. The results of the finite element simulations
reveal that spindle bearing with different preloads greatly affect the
dynamic behavior of the spindle tool unit and hence the dynamic
responses of the vertical column milling system. These results were
validated by performing vibration on the individual spindle tool unit
and the milling machine prototype, respectively. We conclude that
preload of the spindle bearings is an important component affecting
the dynamic characteristics and machining performance of the entire
vertical column structure of the milling machine.
Abstract: Efforts to secure supervisory control and data acquisition
(SCADA) systems must be supported under the guidance of
sound security policies and mechanisms to enforce them. Critical
elements of the policy must be systematically translated into a format
that can be used by policy enforcement components. Ideally, the
goal is to ensure that the enforced policy is a close reflection of
the specified policy. However, security controls commonly used to
enforce policies in the IT environment were not designed to satisfy
the specific needs of the SCADA environment. This paper presents
a language, based on the well-known XACML framework, for the
expression of authorization policies for SCADA systems.
Abstract: This paper presents an overview of the design and
implementation of an online rule-based Expert Systems for Islamic
medication. T his Online Islamic Medication Expert System (OIMES)
focuses on physical illnesses only. Knowledge base of this Expert
System contains exhaustively the types of illness together with their
related cures or treatments/therapies, obtained exclusively from the
Quran and Hadith. Extensive research and study are conducted to
ensure that the Expert System is able to provide the most suitable
treatment with reference to the relevant verses cited in Quran or
Hadith. These verses come together with their related 'actions'
(bodily actions/gestures or some acts) to be performed by the patient
to treat a particular illness/sickness. These verses and the instructions
for the 'actions' are to be displayed unambiguously on the computer
screen. The online platform provides the advantage for patient getting
treatment practically anytime and anywhere as long as the computer
and Internet facility exist. Patient does not need to make appointment
to see an expert for a therapy.
Abstract: Building Sector is the major electricity consumer and
it is costly to building owners. Therefore the application of thermal
energy storage (TES) has gained attractive to reduce energy cost.
Many attractive tariff packages are being offered by the electricity
provider to promote TES. The tariff packages offered higher cost of
electricity during peak period and lower cost of electricity during off
peak period. This paper presented the return of initial investment by
implementing a centralized air-conditioning plant integrated with
thermal energy storage with partially operation strategies. Building
load profile will be calculated hourly according to building
specification and building usage trend. TES operation conditions will
be designed according to building load demand profile, storage
capacity, tariff packages and peak/off peak period. The Payback
Period analysis method was used to evaluate economic analysis. The
investment is considered a good investment where by the initial cost
is recovered less than ten than seven years.
Abstract: Due to increased number of terrorist attacks in recent years, loads induced by explosions need to be incorporated in building designs. For safer performance of a structure, its foundation should have sufficient strength and stability. Therefore, prior to any reconstruction or rehabilitation of a building subjected to blast, it is important to examine adverse effects on the foundation caused by blast induced ground shocks. This paper evaluates the effects of a buried explosion on a pile foundation. It treats the dynamic response of the pile in saturated sand, using explicit dynamic nonlinear finite element software LS-DYNA. The blast induced wave propagation in the soil and the horizontal deformation of pile are presented and the results are discussed. Further, a parametric study is carried out to evaluate the effect of varying the explosive shape on the pile response. This information can be used to evaluate the vulnerability of piled foundations to credible blast events as well as develop guidance for their design.
Abstract: This paper investigates the structure and content of the
wine lists in upscale restaurants in Portugal (N=61). The respondents
considered that a wine list should be easy to use and to modify, welldesigned,
modern and varied. Respondents also stated that they
perform on average 6 revisions to the wine list per year. The
restaurant owner, the restaurant manager and the sommelier were the
main persons in charge of the wine list design. One of the most
important reasons for selecting wines across most restaurants was to
‘complement the menu’ and ‘pairing food with wine’. Restaurants
also reported to be relatively independent from suppliers and
magazine evaluations. Moreover, this work revealed that the
restaurant wine list is considered by restaurateurs as a strategic tool to
sell wine as a complement to the menu, to improve customer
satisfaction and loyalty, to increase restaurant value and to enhance a
successful positioning.
Abstract: In this paper, a novel approach is presented
for designing multiplier-free state-space digital filters. The
multiplier-free design is obtained by finding power-of-2 coefficients
and also quantizing the state variables to power-of-2
numbers. Expressions for the noise variance are derived for the
quantized state vector and the output of the filter. A “structuretransformation
matrix" is incorporated in these expressions. It
is shown that quantization effects can be minimized by properly
designing the structure-transformation matrix. Simulation
results are very promising and illustrate the design algorithm.
Abstract: The current methods of predictive controllers are
utilized for those processes in which the rate of output variations is
not high. For such processes, therefore, stability can be achieved by
implementing the constrained predictive controller or applying
infinite prediction horizon. When the rate of the output growth is
high (e.g. for unstable nonminimum phase process) the stabilization
seems to be problematic. In order to avoid this, it is suggested to
change the method in the way that: first, the prediction error growth
should be decreased at the early stage of the prediction horizon, and
second, the rate of the error variation should be penalized. The
growth of the error is decreased through adjusting its weighting
coefficients in the cost function. Reduction in the error variation is
possible by adding the first order derivate of the error into the cost
function. By studying different examples it is shown that using these
two remedies together, the closed-loop stability of unstable
nonminimum phase process can be achieved.
Abstract: Concrete pavement has superior durability and longer
structural life than asphalt pavement. Concrete pavement requires
less maintenance compared to asphalt pavement which requires maintenance and major rehabilitation. Use of the concrete pavement
has been grown over the past decade in developing countries. Fibre reinforced concrete (FRC) has been successfully used in design of concrete pavement in past decade. In this research, the effect of fibre
volume fraction in modulus of rupture, load-deflection, equivalent flexural strength (fe,3) and the equivalent flexural strength ratio (Re,3)
has been used in different fibre volume fraction. Crimped-type flat
steel fibre of size 50 x 2.0 x 0.6 mm was used with 1.0%, 1.5% and 2.0% volume fraction. Beam specimens of size 500 x 100 x 100 mm were used for flexural as well as with JCI method for analysis flexural toughness, equivalent flexural strength. It was obtained as the 2% fibre volume fractions; reduce 45% of the concrete pavement
thickness.
Abstract: New methodologies for XOR-XNOR circuits are
proposed to improve the speed and power as these circuits are basic
building blocks of many arithmetic circuits. This paper evaluates and
compares the performance of various XOR-XNOR circuits. The
performance of the XOR-XNOR circuits based on TSMC 0.18μm
process models at all range of the supply voltage starting from 0.6V
to 3.3V is evaluated by the comparison of the simulation results
obtained from HSPICE. Simulation results reveal that the proposed
circuit exhibit lower PDP and EDP, more power efficient and faster
when compared with best available XOR-XNOR circuits in the
literature.
Abstract: Topology Optimization is a defined as the method of
determining optimal distribution of material for the assumed design
space with functionality, loads and boundary conditions [1].
Topology optimization can be used to optimize shape for the
purposes of weight reduction, minimizing material requirements or
selecting cost effective materials [2]. Topology optimization has been
implemented through the use of finite element methods for the
analysis, and optimization techniques based on the method of moving
asymptotes, genetic algorithms, optimality criteria method, level sets
and topological derivatives. Case study of Typical “Fuselage design"
is considered for this paper to explain the benefits of Topology
Optimization in the design cycle. A cylindrical shell is assumed as
the design space and aerospace standard pay loads were applied on
the fuselage with wing attachments as constraints. Then topological
optimization is done using Finite Element (FE) based software. This
optimization results in the structural concept design which satisfies
all the design constraints using minimum material.
Abstract: The main goal of the study is to analyze all relevant
properties of the electro hydraulic systems and based on that to make
a proper choice of the control strategy that may be used for the
control of the servomechanism system. A combination of electronic
and hydraulic systems is widely used since it combines the
advantages of both. Hydraulic systems are widely spread because of
their properties as accuracy, flexibility, high horsepower-to-weight
ratio, fast starting, stopping and reversal with smoothness and
precision, and simplicity of operations. On the other hand, the
modern control of hydraulic systems is based on control of the circuit
fed to the inductive solenoid that controls the position of the
hydraulic valve. Since this circuit may be easily handled by PWM
(Pulse Width Modulation) signal with a proper frequency, the
combination of electrical and hydraulic systems became very fruitful
and usable in specific areas as airplane and military industry.
The study shows and discusses the experimental results obtained
by the control strategy (classical feedback (PID) & neural network)
using MATLAB and SIMULINK [1]. Finally, the special attention
was paid to the possibility of neuro-controller design and its
application to control of electro-hydraulic systems and to make
comparative with classical control.
Abstract: This paper address the network reliability optimization
problem in the optical access network design for the 3G cellular
systems. We presents a novel 0-1 integer programming model for
designing optical access network topologies comprised of multi-rings
with common-edge in order to guarantee always-on services. The
results show that the proposed model yields access network
topologies with the optimal reliablity and satisfies both network cost
limitations and traffic demand requirements.
Abstract: Mixed model assembly lines (MMAL) are a type of
production line where a variety of product models similar in product
characteristics are assembled. The effective design of these lines
requires that schedule for assembling the different products is
determined. In this paper we tried to fit the sequencing problem with
the main characteristics of make to order (MTO) environment. The
problem solved in this paper is a multiple objective sequencing
problem in mixed model assembly lines sequencing using weighted
Sum Method (WSM) using GAMS software for small problem and
an effective GA for large scale problems because of the nature of
NP-hardness of our problem and vast time consume to find the
optimum solution in large problems. In this problem three practically
important objectives are minimizing: total utility work, keeping a
constant production rate variation, and minimizing earliness and
tardiness cost which consider the priority of each customer and
different due date which is a real situation in mixed model assembly
lines and it is the first time we consider different attribute to
prioritize the customers which help the company to reduce the cost of
earliness and tardiness. This mechanism is a way to apply an advance
available to promise (ATP) in mixed model assembly line sequencing
which is the main contribution of this paper.