Abstract: In this paper, we present a technical and an economic
assessment of several sources of renewable energy in Saudi Arabia;
mainly solar, wind, hydro and biomass. We analyze the
environmental and climatic conditions in relation to these sources
and give an overview of some of the existing clean energy
technologies. Using standardized cost and efficiency data, we carry
out a cost benefit analysis to understand the economic factors
influencing the sustainability of energy production from renewable
sources in light of the energy cost and demand in the Saudi market.
Finally, we take a look at the Saudi petroleum industry and the
existing sources of conventional energy and assess the potential of
building a successful market for renewable energy under the
constraints imposed by the flow of subsidized cheap oil. We show
that while some renewable energy resources are well suited for
distributed or grid connected generation in the kingdom, their
viability is greatly undercut by the well developed and well
capitalized oil industry.
Abstract: This study experimentally and numerically investigates
motor cooling performance. The motor consists of a centrifugal fan,
two axial fans, a shaft, a stator, a rotor and a heat exchanger with 637
cooling tubes. The pressure rise-flow rate (P-Q) performance curves of
the cooling fans at 1800 rpm are tested using a test apparatus
complying with the Chinese National Standard (CNS) 2726.
Compared with the experimental measurements, the numerical
analysis results show that the P-Q performance curves of the axial fan
and centrifugal fan can be estimated within about 2% and 6%,
respectively. By using the simplified model, setting up the heat
exchanger and stator as porous media, the flow field in the motor is
calculated. By using the results of the flow field near the rotor and
stator, and subjecting the heat generation rate as a boundary condition,
the temperature distributions of the stator and rotor are also calculated.
The simulation results show that the calculated temperature of the
stator winding near the axial fans is lower by about 5% than the
measured value, and the calculated temperature of the stator core
located at the center of the stator is about 1% higher than the measured
value. Besides, discussion is made to improve the motor cooling
performance.
Abstract: Using 1km grid datasets representing monthly mean
precipitation, monthly mean temperature, and dry matter production
(DMP), we considered the regional plant production ability in
Southeast and South Asia, and also employed pixel-by-pixel
correlation analysis to assess the intensity of relation between climate
factors and plant production. While annual DMP in South Asia was
approximately less than 2,000kg, the one in most part of Southeast
Asia exceeded 2,500 - 3,000kg. It suggested that plant production in
Southeast Asia was superior to South Asia, however, Rain-Use
Efficiency (RUE) representing dry matter production per 1mm
precipitation showed that inland of Indochina Peninsula and India
were higher than islands in Southeast Asia. By the results of
correlation analysis between climate factors and DMP, while the area
in most parts of Indochina Peninsula indicated negative correlation
coefficients between DMP and precipitation or temperature, the area
in Malay Peninsula and islands showed negative correlation to
precipitation and positive one to temperature, and most part of India
dominating South Asia showed positive to precipitation and negative
to temperature. In addition, the areas where the correlation coefficients
exceeded |0.8| were regarded as “susceptible" to climate factors, and
the areas smaller than |0.2| were “insusceptible". By following the
discrimination, the map implying expected impacts by climate change
was provided.
Abstract: In this study the mixed mode fracture mechanics
parameters were investigated for high tensile steel butt welded joint
based on modified Arcan test and finite element analysis was used to
evaluate the effect of crack length on fracture criterion. The nondimensional
stress intensity factors, strain energy release rates and Jintegral
energy on crack tip were obtained for various in-plane
loading combinations on Arcan specimen starting from pure mode-I
to pure mode-II loading conditions. The specimen and apparatus were
modeled by finite element method and analyzed under various
loading angles (between 0 to 90 degrees with 15 degree interval) to
simulate the pure mode-I, II and mixed mode fracture. Since the
analytical results are independent from elasticity modules for
isotropic materials, therefore the results in elastic fields can be used
for Arcan specimens. The main objective of this study was to
evaluate the geometric calibration factors for modified Arcan test
specimen in order to obtain fracture toughness under mixed mode
loading conditions.
Abstract: New Growth Theory helps us make sense of the
ongoing shift from a resource-based economy to a knowledge-based
economy. It underscores the point that the economic processes which
create and diffuse new knowledge are critical to shaping the growth
of nations, communities and individual firms. In all too many
contributions to New (Endogenous) Growth Theory – though not in
all – central reference is made to 'a stock of knowledge', a 'stock of
ideas', etc., this variable featuring centre-stage in the analysis. Yet it
is immediately apparent that this is far from being a crystal clear
concept. The difficulty and uncertainty of being able to capture the
value associated with knowledge is a real problem. The intent of this
paper is introducing new thinking and theorizing about the
knowledge and its measurability in new growth theory. Moreover the
study aims to synthesize various strain of the literature with a
practical bearing on knowledge concept. By contribution of
institution framework which is found within NGT, we can indirectly
measure the knowledge concept. Institutions matter because they
shape the environment for production and employment of new
knowledge
Abstract: The paper deals with the most important changes that have occurred in business because of social media and its impact on organisations and leadership in recent years. It seeks to synthesize existing research, theories and concepts, in order to understand "social destinations", and to provide a bridge from past research to future success. Becoming a "social destination" is a strategic and tactical leadership and management issue and the paper will present the importance of destination leadership in choosing the way towards a social destination and some organisational models. It also presents some social media tools that can be used in transforming a destination into a social one. Adapting organisations to the twentyfirst century means adopting social media as a way of life and a way of business.
Abstract: Most of the academics connect a theory of
multiculturalism with globalization and limit it by last decades of
20th century. However, Kazakh society encountered with this
problem when the Soviet-s rule emerged. As a result of repression,
the Second World War, development of virgin lands representatives
of more than 100 nationalities lives in Kazakhstan. Communist
ideology propagandized internationalism, which would defined
principles of multicultural community but a common ideology
demands a single culture. As a result multicultural society in the
USSR developed under control of Russian culture. Education in the
USSR was conducted in two departments: autochthonous and
Russian. Autochthonous education narrowed student capabilities.
Also because of soviet ideology science was conducted in Russian
Universities provided education in Russian and all science literature
were in Russian. Exceptions were humanitarian fields where Kazakh
departments were admitted. Naturally non-Kazakhs studied in
Russian departments, moreover Kazakhs preferred to study in
Russian as most do nowadays preferring English. As a result Kazakh
society consisted of Kazakhs, Kazakhs who recognized Russian as a
mother tongue and other nationalities who were also Russian
speakers. This aspect continues to distinguish particular qualities of
multicultural community in Kazakhstan.
Abstract: Warranty is a powerful marketing tool for the
manufacturer and a good protection for both the manufacturer and the
customer. However, warranty always involves additional costs to the
manufacturer, which depend on product reliability characteristics and
warranty parameters. This paper presents an approach to optimisation
of warranty parameters for known product failure distribution to
reduce the warranty costs to the manufacturer while retaining the
promotional function of the warranty. Combination free replacement
and pro-rata warranty policy is chosen as a model and the length of
free replacement period and pro-rata policy period are varied, as well
as the coefficients that define the pro-rata cost function. Multiparametric
warranty optimisation is done by using genetic algorithm.
Obtained results are guideline for the manufacturer to choose the
warranty policy that minimises the costs and maximises the profit.
Abstract: Food borne illnesses have been reported to be a global
health challenge. Annual incidences of food–related diseases involve
76 million cases, of which only 14 million can be traced to known
pathogens. Poor hygienic practices have contributed greatly to this. It
has been reported that in the year 2000 about 2.1 million people died
from diarrheal diseases, hence, there is a need to ensure food safety at
all level. This study focused on the sterility examination and
inhibitory effect of honey samples on selected gram negative and
gram positive food borne pathogen from South West Nigeria. The
laboratory examinations revealed the presence of some bacterial and
fungal contaminations of honey samples and that inhibitory activity
of the honey sample was more pronounced on the gram negative
bacteria than the gram positive bacterial isolates. Antibiotic
sensitivity test conducted on the different bacterial isolates also
showed that honey was able to inhibit the proliferation of the tested
bacteria than the employed antibiotics.
Abstract: Data Envelopment Analysis (DEA) is a methodology
that computes efficiency values for decision making units (DMU) in a
given period by comparing the outputs with the inputs. In many cases,
there are some time lag between the consumption of inputs and the
production of outputs. For a long-term research project, it is hard to
avoid the production lead time phenomenon. This time lag effect
should be considered in evaluating the performance of organizations.
This paper suggests a model to calculate efficiency values for the
performance evaluation problem with time lag. In the experimental
part, the proposed methods are compared with the CCR and an
existing time lag model using the data set of the 21st century frontier
R&D program which is a long-term national R&D program of Korea.
Abstract: Airport capacity has always been perceived in the
traditional sense as the number of aircraft operations during a
specified time corresponding to a tolerable level of average delay and
it mostly depends on the airside characteristics, on the fleet mix
variability and on the ATM. The adoption of the Directive
2002/30/EC in the EU countries drives the stakeholders to conceive
airport capacity in a different way though. Airport capacity in this
sense is fundamentally driven by environmental criteria, and since
acoustical externalities represent the most important factors, those are
the ones that could pose a serious threat to the growth of airports and
to aviation market itself in the short-medium term. The importance of
the regional airports in the deregulated market grew fast during the
last decade since they represent spokes for network carriers and a
preferential destination for low-fares carriers. Not only regional
airports have witnessed a fast and unexpected growth in traffic but
also a fast growth in the complaints for the nuisance by the people
living near those airports. In this paper the results of a study
conducted in cooperation with the airport of Bologna G. Marconi are
presented in order to investigate airport acoustical capacity as a defacto
constraint of airport growth.
Abstract: Overcurrent (OC) relays are the major protection
devices in a distribution system. The operating time of the OC relays
are to be coordinated properly to avoid the mal-operation of the
backup relays. The OC relay time coordination in ring fed
distribution networks is a highly constrained optimization problem
which can be stated as a linear programming problem (LPP). The
purpose is to find an optimum relay setting to minimize the time of
operation of relays and at the same time, to keep the relays properly
coordinated to avoid the mal-operation of relays.
This paper presents two phase simplex method for optimum time
coordination of OC relays. The method is based on the simplex
algorithm which is used to find optimum solution of LPP. The
method introduces artificial variables to get an initial basic feasible
solution (IBFS). Artificial variables are removed using iterative
process of first phase which minimizes the auxiliary objective
function. The second phase minimizes the original objective function
and gives the optimum time coordination of OC relays.
Abstract: Recently global concerns for the energy security have
steadily been on the increase and are expected to become a major
issue over the next few decades. Energy security refers to a resilient
energy system. This resilient system would be capable of
withstanding threats through a combination of active, direct security
measures and passive or more indirect measures such as redundancy,
duplication of critical equipment, diversity in fuel, other sources of
energy, and reliance on less vulnerable infrastructure. Threats and
disruptions (disturbances) to one part of the energy system affect
another. The paper presents methodology in theoretical background
about energy system as an interconnected network and energy supply
disturbances impact to the network. The proposed methodology uses
a network flow approach to develop mathematical model of the
energy system network as the system of nodes and arcs with energy
flowing from node to node along paths in the network.
Abstract: Palladium-catalyzed hydrodechlorination is a
promising alternative for the treatment of environmentally relevant
water bodies, such as groundwater, contaminated with chlorinated
organic compounds (COCs). In the aqueous phase
hydrodechlorination of COCs, Pd-based catalysts were found to have
a very high catalytic activity. However, the full utilization of the
catalyst-s potential is impeded by the sensitivity of the catalyst to
poisoning and deactivation induced by reduced sulfur compounds
(e.g. sulfides). Several regenerants have been tested before to recover
the performance of sulfide-fouled Pd catalyst. But these only
delivered partial success with respect to re-establishment of the
catalyst activity. In this study, the deactivation behaviour of
Pd/Al2O3 in the presence of sulfide was investigated. Subsequent to
total deactivation the catalyst was regenerated in the aqueous phase
using potassium permanganate. Under neutral pH condition,
oxidative regeneration with permanganate delivered a slow recovery
of catalyst activity. However, changing the pH of the bulk solution to
acidic resulted in the complete recovery of catalyst activity within a
regeneration time of about half an hour. These findings suggest the
superiority of permanganate as regenerant in re-activating Pd/Al2O3
by oxidizing Pd-bound sulfide.
Abstract: The quest for alternatefuels for a CI engine has
become all the more imperative considering its importance in the
economy of a nation and from the standpoint of preserving the environment. Reported in this paper are the combustion performance and P-θ characteristics of a CI engine operating on B20 biodiesel fuel derived from Jatropha oil.Itis observed that the twin effect of advancing the injection timing and increasing the injector opening pressure (IOP) up to 220 barhas resulted in minimum brake specific
energy consumption and higherpeak pressure. It is also observed that
the crank angle of occurrence of peak pressure progressestowards top
dead center (TDC) as the timing is advanced and IOP is increased.
Abstract: In this paper, to optimize the “Characteristic Straight Line Method" which is used in the soil displacement analysis, a “best estimate" of the geodetic leveling observations has been achieved by taking in account the concept of 'Height systems'. This concept has been discussed in detail and consequently the concept of “height". In landslides dynamic analysis, the soil is considered as a mosaic of rigid blocks. The soil displacement has been monitored and analyzed by using the “Characteristic Straight Line Method". Its characteristic components have been defined constructed from a “best estimate" of the topometric observations. In the measurement of elevation differences, we have used the most modern leveling equipment available. Observational procedures have also been designed to provide the most effective method to acquire data. In addition systematic errors which cannot be sufficiently controlled by instrumentation or observational techniques are minimized by applying appropriate corrections to the observed data: the level collimation correction minimizes the error caused by nonhorizontality of the leveling instrument's line of sight for unequal sight lengths, the refraction correction is modeled to minimize the refraction error caused by temperature (density) variation of air strata, the rod temperature correction accounts for variation in the length of the leveling rod' s Invar/LO-VAR® strip which results from temperature changes, the rod scale correction ensures a uniform scale which conforms to the international length standard and the introduction of the concept of the 'Height systems' where all types of height (orthometric, dynamic, normal, gravity correction, and equipotential surface) have been investigated. The “Characteristic Straight Line Method" is slightly more convenient than the “Characteristic Circle Method". It permits to evaluate a displacement of very small magnitude even when the displacement is of an infinitesimal quantity. The inclination of the landslide is given by the inverse of the distance reference point O to the “Characteristic Straight Line". Its direction is given by the bearing of the normal directed from point O to the Characteristic Straight Line (Fig..6). A “best estimate" of the topometric observations was used to measure the elevation of points carefully selected, before and after the deformation. Gross errors have been eliminated by statistical analyses and by comparing the heights within local neighborhoods. The results of a test using an area where very interesting land surface deformation occurs are reported. Monitoring with different options and qualitative comparison of results based on a sufficient number of check points are presented.
Abstract: A filter is used to remove undesirable frequency information from a dynamic signal. This paper shows that the Znotch filter filtering technique can be applied to remove the noise nuisance from a machining signal. In machining, the noise components were identified from the sound produced by the operation of machine components itself such as hydraulic system, motor, machine environment and etc. By correlating the noise components with the measured machining signal, the interested components of the measured machining signal which was less interfered by the noise, can be extracted. Thus, the filtered signal is more reliable to be analysed in terms of noise content compared to the unfiltered signal. Significantly, the I-kaz method i.e. comprises of three dimensional graphical representation and I-kaz coefficient, Z∞ could differentiate between the filtered and the unfiltered signal. The bigger space of scattering and the higher value of Z∞ demonstrated that the signal was highly interrupted by noise. This method can be utilised as a proactive tool in evaluating the noise content in a signal. The evaluation of noise content is very important as well as the elimination especially for machining operation fault diagnosis purpose. The Z-notch filtering technique was reliable in extracting noise component from the measured machining signal with high efficiency. Even though the measured signal was exposed to high noise disruption, the signal generated from the interaction between cutting tool and work piece still can be acquired. Therefore, the interruption of noise that could change the original signal feature and consequently can deteriorate the useful sensory information can be eliminated.
Abstract: Nigeria is considered as one of the many countries in
sub-Saharan Africa with a weak economy and gross deficiencies in technology and engineering. Available data from international monitoring and regulatory organizations show that technology is pivotal to determining the economic strengths of nations all over the
world. Education is critical to technology acquisition, development,
dissemination and adaptation. Thus, this paper seeks to critically
assess and discuss issues and challenges facing technological
advancement in Nigeria, particularly in the education sector, and also
proffers solutions to resuscitate the Nigerian education system
towards achieving national technological and economic sustainability
such that Nigeria can compete favourably with other technologicallydriven
economies of the world in the not-too-distant future.
Abstract: In this paper the design of maximally flat linear phase
finite impulse response (FIR) filters is considered. The problem is
handled with totally two different approaches. The first one is
completely deterministic numerical approach where the problem is
formulated as a Linear Complementarity Problem (LCP). The other
one is based on a combination of Markov Random Fields (MRF's)
approach with messy genetic algorithm (MGA). Markov Random
Fields (MRFs) are a class of probabilistic models that have been
applied for many years to the analysis of visual patterns or textures.
Our objective is to establish MRFs as an interesting approach to
modeling messy genetic algorithms. We establish a theoretical result
that every genetic algorithm problem can be characterized in terms of
a MRF model. This allows us to construct an explicit probabilistic
model of the MGA fitness function and introduce the Ising MGA.
Experimentations done with Ising MGA are less costly than those
done with standard MGA since much less computations are involved.
The least computations of all is for the LCP. Results of the LCP,
random search, random seeded search, MGA, and Ising MGA are
discussed.
Abstract: In this paper, we argue that Design research is basic to countries- national productivity and competition agendas at the same time that vagaries of research training presents as one of the barriers faced by Design Higher Degree by Research students in engaging those agendas. We argue that, given industry requirements for research-trained recruits, students have the right to expect that research training will provide the foundations of a successful career on an academic or research pathway or a professional pathway, but that universities have yet to address problems in their provision of research training for Design doctoral students. We suggest that to facilitate this, rigorous research conducted on the provision of Doctoral programs in Design would serve to inform future activities in Design research in productive ways.