Abstract: Accurate timing alignment and stability is important
to maximize the true counts and minimize the random counts in
positron emission tomography So signals output from detectors must
be centering with the two isotopes to pre-operation and fed signals
into four units of pulse-processing units, each unit can accept up to
eight inputs. The dual source computed tomography consist two units
on the left for 15 detector signals of Cs-137 isotope and two units on
the right are for 15 detectors signals of Co-60 isotope. The gamma
spectrum consisting of either single or multiple photo peaks. This
allows for the use of energy discrimination electronic hardware
associated with the data acquisition system to acquire photon counts
data with a specific energy, even if poor energy resolution detectors
are used. This also helps to avoid counting of the Compton scatter
counts especially if a single discrete gamma photo peak is emitted by
the source as in the case of Cs-137. In this study the polyenergetic
version of the alternating minimization algorithm is applied to the
dual energy gamma computed tomography problem.
Abstract: The aim of this study was to compare the effects
of an altitude training camp on heart rate variability and
performance in elite triathletes. Ten athletes completed 20 days of live-high, train-low training at 1650m. Athletes
underwent pre and post 800-m swim time trials at sea-level, and two heart rate variability tests at 1650m on the first and
last day of the training camp. Based on their time trial results,
athletes were divided into responders and non-responders. Relative to the non-responders, the responders sympathetic-toparasympathetic
ratio decreased substantially after 20 days of altitude training (-0.68 ± 1.08 and -1.2 ± 0.96, mean ± 90%
confidence interval for supine and standing respectively). In
addition, sympathetic activity while standing was also
substantially lower post-altitude in the responders compared to the non-responders (-1869 ± 4764 ms2). Results indicate that
responders demonstrated a change to more vagal
predominance compared to non-responders.
Abstract: Roadways in Amman city face many problems consequent upon poor drainage systems. Evaluation tools are necessary to identify those roads needing improvement in their drainage system, and those needing regular maintenance. This work aims at evaluating drainage conditions in selected roadways in Amman city with the intent of identifying the problems encountered in their drainage systems. Three sites in the vicinity of Amman city have been selected and then inspected via several field visits to determine the state of their existing drainage systems and define the major problems encountered in these systems. The evaluation tool used in this study is based on visual inspection supported by photographs that depicted the defined problems. Following the field assessment, the drainage system in each road was rated as excellent, fair, good, or poor. The study reveals that more than 60% of the roadways in the selected sites were in poor drainage conditions, which lead to tremendous environmental problems. This assessment serves as a guide for local decision makers to help plan for the maintenance of Amman city roadways drainage systems, and propose ways of managing the associated problems.
Abstract: The provision of urban public transport in Indonesia is not free of problems. Some of the problems include: an overall lack of capacity, lack of quality and choice, severe traffic congestions and insufficient fund to renew and repair vehicles. Generally, the comfort and quality of the city bus is poor, and many of the vehicles are dilapidated and dirty. Surveys were carried out in the city of Yogyakarta, by counting city bus vehicles and occupancies, interviewing the bus passengers, drivers and institutional staffs, who involve in public transport management. This paper will then analyze the possible plan to develop the public transport system to become more attractive and to improve the public transport management. The short, medium and long term plans are analyzed, to find the best solutions. Some constraints such as social impacts and financial impact are also taken into accounts.
Abstract: Education, as the most important resource in any country, has multiplying effects on all facets of development in a society. The new social realities, particularly the interplay between democratization of education; unprecedented developments in IT sector; emergence of knowledge society, liberalization of economy and globalization have greatly influenced the educational process of all nations. This turbulence entails upon education to undergo dramatic changes to keep up with the new expectations. Growth of entrepreneurship among Indian women is highly important for empowering them and this is highly essential for socio-economic development of a society. Unfortunately in India there is poor acceptance of entrepreneurship among women as unfounded myths and fears restrain them to be enterprising. To remove these inhibitions, education system needs to be re-engineered to make entrepreneurship more acceptable. This paper empirically analyses the results of a survey done on around 500 female graduates in North India to measure and evaluate various entrepreneurial traits present in them. A formative model has been devised in this context, which should improve the teaching-learning process in our education system, which can lead to sustainable growth of women entrepreneurship in India.
Abstract: Process control and energy conservation are the two
primary reasons for using an adjustable speed drive. However,
voltage sags are the most important power quality problems facing
many commercial and industrial customers. The development of
boost converters has raised much excitement and speculation
throughout the electric industry. Now utilities are looking to these
devices for performance improvement and reliability in a variety of
areas. Examples of these include sags, spikes, or transients in supply
voltage as well as unbalanced voltages, poor electrical system
grounding, and harmonics. In this paper, simulations results are
presented for the verification of the proposed boost converter
topology. Boost converter provides ride through capability during
sag and swell. Further, input currents are near sinusoidal. This
eliminates the need of braking resistor also.
Abstract: Artificial Bee Colony (ABC) algorithm is a relatively new swarm intelligence technique for clustering. It produces higher
quality clusters compared to other population-based algorithms but with poor energy efficiency, cluster quality consistency and typically slower in convergence speed. Inspired by energy saving foraging behavior of natural honey bees this paper presents a Quality and Quantity Aware Artificial Bee Colony (Q2ABC) algorithm to improve quality of cluster identification, energy efficiency and convergence speed of the original ABC. To evaluate the performance of Q2ABC algorithm, experiments were conducted on a suite of ten benchmark UCI datasets. The results demonstrate Q2ABC outperformed ABC and K-means algorithm in the quality of clusters delivered.
Abstract: Text data mining is a process of exploratory data
analysis. Classification maps data into predefined groups or classes.
It is often referred to as supervised learning because the classes are
determined before examining the data. This paper describes proposed
radial basis function Classifier that performs comparative crossvalidation
for existing radial basis function Classifier. The feasibility
and the benefits of the proposed approach are demonstrated by means
of data mining problem: direct Marketing. Direct marketing has
become an important application field of data mining. Comparative
Cross-validation involves estimation of accuracy by either stratified
k-fold cross-validation or equivalent repeated random subsampling.
While the proposed method may have high bias; its performance
(accuracy estimation in our case) may be poor due to high variance.
Thus the accuracy with proposed radial basis function Classifier was
less than with the existing radial basis function Classifier. However
there is smaller the improvement in runtime and larger improvement
in precision and recall. In the proposed method Classification
accuracy and prediction accuracy are determined where the
prediction accuracy is comparatively high.
Abstract: It can be said that the business sector is faced with a range of challenges–a rapidly changing business environment, an increase and diversification of customers- demands and the consequent need for quick response–for having in place flexible management and production info systems. As a matter of fact, many manufacturers have adopted production info management systems such as MES and ERP. Nevertheless, managers are having difficulties obtaining ever-changing production process information in real time, or responding quickly to any change in production related needs on the basis of such information. This is because they rely on poor production info systems which are not capable of providing real-time factory settings. If the manufacturer doesn-t have a capacity for collecting or digitalizing the 4 Ms (Man, Machine, Material, Method), which are resources for production, on a real time basis, it might to difficult to effectively maintain the information on production process. In this regard, this paper will introduce some new alternatives to the existing methods of collecting the 4 Ms in real time, which are currently comprise the production field.
Abstract: Tanzania secondary schools in rural areas are geographically and socially isolated, hence face a number of problems in getting learning materials resulting in poor performance in National examinations. E-learning as defined to be the use of information and communication technology (ICT) for supporting the educational processes has motivated Tanzania to apply ICT in its education system. There has been effort to improve secondary school education using ICT through several projects. ICT for e-learning to Tanzania rural secondary school is one of the research projects conceived by the University of Dar-es-Salaam through its College of Engineering and Technology. The main objective of the project is to develop a tool to enable ICT support rural secondary school. The project is comprehensive with a number of components, one being development of e-learning management system (e-LMS) for Tanzania secondary schools. This paper presents strategies of developing e-LMS. It shows the importance of integrating action research methodology with the modeling methods as presented by model driven architecture (MDA) and the usefulness of Unified Modeling Language (UML) on the issue of modeling. The benefit of MDA will go along with the development based on software development life cycle (SDLC) process, from analysis and requirement phase through design and implementation stages as employed by object oriented system analysis and design approach. The paper also explains the employment of open source code reuse from open source learning platforms for the context sensitive development of the e-LMS for Tanzania secondary schools.
Abstract: The presence of toxic heavy metals in industrial
effluents is one of the serious threats to the environment. Heavy
metals such as Cadmium, Chromium, Lead, Nickel, Zinc, Mercury,
Copper, Arsenic are found in the effluents of industries such as
foundries, electroplating, petrochemical, battery manufacturing,
tanneries, fertilizer, dying, textiles, metallurgical and metal finishing.
Tremendous increase of industrial copper usage and its presence in
industrial effluents has lead to a growing concern about the fate and
effects of Copper in the environment. Percolation of industrial
effluents through soils leads to contamination of ground water and
soils. The transport of heavy metals and their diffusion into the soils
has therefore, drawn the attention of the researchers.
In this study, an attempt has been made to delineate the
mechanisms of transport and fate of copper in terrestrial
environment. Column studies were conducted using perplex glass
square column of dimension side 15 cm and 1.35 m long. The soil
samples were collected from a natural drain near Mohali (India). The
soil was characterized to be poorly graded sandy loam. The soil was
compacted to the field dry density level of about 1.6 g/cm3. Break
through curves for different depths of the column were plotted. The
results of the column study indicated that the copper has high
tendency to flow in the soils and fewer tendencies to get absorbed on
the soil particles. The t1/2 estimates obtained from the studies can be
used for design copper laden wastewater disposal systems.
Abstract: As seen in literature, about 70% of the improvement initiatives fail, and a significant number do not even get started. This paper analyses the problem of failing initiatives on Software Process Improvement (SPI), and proposes good practices supported by motivational tools that can help minimizing failures. It elaborates on the hypothesis that human factors are poorly addressed by deployers, especially because implementation guides usually emphasize only technical factors. This research was conducted with SPI deployers and analyses 32 SPI initiatives. The results indicate that although human factors are not commonly highlighted in guidelines, the successful initiatives usually address human factors implicitly. This research shows that practices based on human factors indeed perform a crucial role on successful implantations of SPI, proposes change management as a theoretical framework to introduce those practices in the SPI context and suggests some motivational tools based on SPI deployers experience to support it.
Abstract: Risk management is an essential fraction of project management, which plays a significant role in project success. Many failures associated with Web projects are the consequences of poor awareness of the risks involved and lack of process models that can serve as a guideline for the development of Web based applications. To circumvent this problem, contemporary process models have been devised for the development of conventional software. This paper introduces the WPRiMA (Web Project Risk Management Assessment) as the tool, which is used to implement RIAP, the risk identification architecture pattern model, which focuses upon the data from the proprietor-s and vendor-s perspectives. The paper also illustrates how WPRiMA tool works and how it can be used to calculate the risk level for a given Web project, to generate recommendations in order to facilitate risk avoidance in a project, and to improve the prospects of early risk management.
Abstract: High-frequency (HF) communications have been used by military organizations for more than 90 years. The opportunity of very long range communications without the need for advanced equipment makes HF a convenient and inexpensive alternative of satellite communications. Besides the advantages, voice and data transmission over HF is a challenging task, because the HF channel generally suffers from Doppler shift and spread, multi-path, cochannel interference, and many other sources of noise. In constructing an HF data modem, all these effects must be taken into account. STANAG 4539 is a NATO standard for high-speed data transmission over HF. It allows data rates up to 12800 bps over an HF channel of 3 kHz. In this work, an efficient implementation of STANAG 4539 on a single Texas Instruments- TMS320C6747 DSP chip is described. The state-of-the-art algorithms used in the receiver and the efficiency of the implementation enables real-time high-speed data / digitized voice transmission over poor HF channels.
Abstract: Food and fibre production in arid and semi-arid regions has emerged as one of the major challenges for various socio-economic and political reasons such as the food security and self-sufficiency. Productive use of the renewable water resources has risen on top ofthe decision-making agenda. For this reason, efficient operation and maintenance of modern irrigation and drainage schemes become part and parcel and indispensible reality in agricultural policy making arena. The aim of this paper is to investigate the complexity of operating and maintaining such schemes, mainly focussing on challenges which enhance and opportunities that impedsustainable food and fibre production. The methodology involved using secondary data complemented byroutine observations and stakeholders views on issues that influence the O&M in the Dez command area. The SPSS program was used as an analytical framework for data analysis and interpretation.Results indicate poor application efficiency in most croplands, much of which is attributed to deficient operation of conveyance and distribution canals. These in turn, are reportedly linked to inadequate maintenance of the pumping stations and hydraulic structures like turnouts,flumes and other control systems particularly in the secondary and tertiary canals. Results show that the aforementioned deficiencies have been the major impediment to establishing regular flow toward the farm gates which subsequently undermine application efficiency and tillage operationsat farm level. Results further show that accumulative impact of such deficiencies has been the major causes of poorcrop yield and quality that deem production system in these croplands uneconomic. Results further show that the present state might undermine the sustainability of agricultural system in the command area. The overall conclusion being that present water management is unlikely to be responsive to challenges that the sector faces. And in the absence of coherent measures to shift the status quo situation in favour of more productive resource use, it would be hard to fulfil the objectives of the National Economic and Socio-cultural Development Plans.
Abstract: Decision Support System (DSS) are interactive
software systems that are built to assist the management of an
organization in the decision making process when faced with nonroutine
problems in a specific application domain. Non-functional
requirements (NFRs) for a DSS deal with the desirable qualities and
restrictions that the DSS functionalities must satisfy. Unlike the
functional requirements, which are tangible functionalities provided
by the DSS, NFRs are often hidden and transparent to DSS users but
affect the quality of the provided functionalities. NFRs are often
overlooked or added later to the system in an ad hoc manner, leading
to a poor overall quality of the system. In this paper, we discuss the
development of NFRs as part of the requirements engineering phase
of the system development life cycle of DSSs. To help eliciting
NFRs, we provide a comprehensive taxonomy of NFRs for DSSs.
Abstract: The response of growth and yield of rainfed-chickpea
to population density should be evaluated based on long-term
experiments to include the climate variability. This is achievable just
by simulation. In this simulation study, this evaluation was done by
running the CYRUS model for long-term daily weather data of five
locations in Iran. The tested population densities were 7 to 59 (with
interval of 2) stands per square meter. Various functions, including
quadratic, segmented, beta, broken linear, and dent-like functions,
were tested. Considering root mean square of deviations and linear
regression statistics [intercept (a), slope (b), and correlation
coefficient (r)] for predicted versus observed variables, the quadratic
and broken linear functions appeared to be appropriate for describing
the changes in biomass and grain yield, and in harvest index,
respectively. Results indicated that in all locations, grain yield tends
to show increasing trend with crowding the population, but
subsequently decreases. This was also true for biomass in five
locations. The harvest index appeared to have plateau state across
low population densities, but decreasing trend with more increasing
density. The turning point (optimum population density) for grain
yield was 30.68 stands per square meter in Isfahan, 30.54 in Shiraz,
31.47 in Kermanshah, 34.85 in Tabriz, and 32.00 in Mashhad. The
optimum population density for biomass ranged from 24.6 (in
Tabriz) to 35.3 stands per square meter (Mashhad). For harvest index
it varied between 35.87 and 40.12 stands per square meter.
Abstract: The International Classification of Primary Care (ICPC), which belongs to the WHO Family of International Classifications (WHO-FIC), has a low granularity, which is convenient for describing general medical practice. However, its lack of specificity makes it useful to be used along with an interface terminology. An international survey has been performed, using a questionnaire sent by email to experts from 25 countries, in order to describe the terminologies interfacing with ICPC. Eleven interface terminologies have been identified, developed in Argentina, Australia, Belgium (2), Canada, Denmark, France, Germany, Norway, South Africa, and The Netherlands. Globally, these systems have been poorly assessed until now.
Abstract: While financial institutions have faced difficulties
over the years for a multitude of reasons, the major cause of serious
banking problems continues to be directly related to lax credit
standards for borrowers and counterparties, poor portfolio risk
management, or a lack of attention to changes in economic or other
circumstances that can lead to a deterioration in the credit standing of
a bank's counterparties. Credit risk is most simply defined as the
potential that a bank borrower or counterparty will fail to meet its
obligations in accordance with agreed terms. The goal of credit risk
management is to maximize a bank's risk-adjusted rate of return by
maintaining credit risk exposure within acceptable parameters. Banks
need to manage the credit risk inherent in the entire portfolio as well
as the risk in individual credits or transactions. Banks should also
consider the relationships between credit risk and other risks. The
effective management of credit risk is a critical component of a
comprehensive approach to risk management and essential to the
long-term success of any banking organization. In this research we
also study the relationship between credit risk indices and borrower-s
timely payback in Karafarin bank.
Abstract: Sedimentation formation is a complex hydraulic phenomenon that has emerged as a major operational and maintenance consideration in modern hydraulic engineering in general and river engineering in particular. Sediments accumulation along the river course and their eventual storage in a form of islands affect water intake in the canal systems that are fed by the storage reservoirs. Without proper management, sediment transport can lead to major operational challenges in water distribution system of arid regions like the Dez and Hamidieh command areas. The paper aims to investigate sedimentation in the Western Canal of Dez Diversion Weir using the SHARC model and compare the results with the two intake structures of the Hamidieh dam in Iran using SSIIM model. The objective was to identify the factors which influence the process, check reliability of outcome and provide ways in which to mitigate the implications on operation and maintenance of the structures. Results estimated sand and silt bed loads concentrations to be 193 ppm and 827ppm respectively. This followed ,ore or less similar pattern in Hamidieh where the sediment formation impeded water intake in the canal system. Given the available data on average annual bed loads and average suspended sediment loads of 165ppm and 837ppm in the Dez, there was a significant statistical difference (16%) between the sand grains, whereas no significant difference (1.2%) was find in the silt grain sizes. One explanation for such finding being that along the 6 Km river course there was considerable meandering effects which explains recent shift in the hydraulic behavior along the stream course under investigation. The sand concentration in downstream relative to present state of the canal showed a steep descending curve. Sediment trapping on the other hand indicated a steep ascending curve. These occurred because the diversion weir was not considered in the simulation model. The comparative study showed very close similarities in the results which explains the fact that both software can be used as accurate and reliable analytical tools for simulation of the sedimentation in hydraulic engineering.