Abstract: This paper presents the utilizing of ferroelectric
material on antenna application. There are two different ferroelectric
had been used on the proposed antennas which include of Barium
Strontium Titanate (BST) and Bismuth Titanate (BiT), suitable for
Access Points operating in the WLAN IEEE 802.11 b/g and WiMAX
IEEE 802.16 within the range of 2.3 GHz to 2.5 GHz application.
BST, which had been tested to own a dielectric constant of εr = 15
while BiT has a dielectric constant that higher than BST which is εr =
21 and both materials are in rectangular shaped. The influence of
various parameters on antenna characteristics were investigated
extensively using commercial electromagnetic simulations software
by Communication Simulation Technology (CST). From theoretical
analysis and simulation results, it was demonstrated that ferroelectric
material used have not only improved the directive emission but also
enhanced the radiation efficiency.
Abstract: This study deals with the phenomena of reflection and transmission (refraction) of qSV-waves, for an incident of quasi transverse vertically waves, at a plane interface of two semi-infinite piezoelectric elastic media under the influence of the initial stresses. The relations governing the reflection and transmission coefficients of these reflected waves for various suitable boundary conditions are derived. We have shown analytically that reflection and transmission coefficients of (qP) and (qSV) waves depend upon the angle of incidence, the parameters of electric potential, the material constants of the medium as will as the initial stresses presented in the media. The numerical calculations of the reflection and transmission amplitude ratios for different values of initial stresses have been carried out by computer for different materials as examples and the results are given in the form of graphs. Finally, some of particular cases are considered.
Abstract: In this paper we propose an enhanced equalization technique for multi-carrier code division multiple access (MC-CDMA). This method is based on the control of Equal Gain Combining (EGC) technique. Indeed, we introduce a new level changer to the EGC equalizer in order to adapt the equalization parameters to the channel coefficients. The optimal equalization level is, first, determined by channel training. The new approach reduces drastically the mutliuser interferences caused by interferes, without increasing the noise power. To compare the performances of the proposed equalizer, the theoretical analysis and numerical performances are given.
Abstract: In designing river intakes and diversion structures, it is paramount that the sediments entering the intake are minimized or, if possible, completely separated. Due to high water velocity, sediments can significantly damage hydraulic structures especially when mechanical equipment like pumps and turbines are used. This subsequently results in wasting water, electricity and further costs. Therefore, it is prudent to investigate and analyze the performance of lateral intakes affected by sediment control structures. Laboratory experiments, despite their vast potential and benefits, can face certain limitations and challenges. Some of these include: limitations in equipment and facilities, space constraints, equipment errors including lack of adequate precision or mal-operation, and finally, human error. Research has shown that in order to achieve the ultimate goal of intake structure design – which is to design longlasting and proficient structures – the best combination of sediment control structures (such as sill and submerged vanes) along with parameters that increase their performance (such as diversion angle and location) should be determined. Cost, difficulty of execution and environmental impacts should also be included in evaluating the optimal design. This solution can then be applied to similar problems in the future. Subsequently, the model used to arrive at the optimal design requires high level of accuracy and precision in order to avoid improper design and execution of projects. Process of creating and executing the design should be as comprehensive and applicable as possible. Therefore, it is important that influential parameters and vital criteria is fully understood and applied at all stages of choosing the optimal design. In this article, influential parameters on optimal performance of the intake, advantages and disadvantages, and efficiency of a given design are studied. Then, a multi-criterion decision matrix is utilized to choose the optimal model that can be used to determine the proper parameters in constructing the intake.
Abstract: This paper proposes a method to vibration analysis in
order to on-line monitoring and predictive maintenance during the
milling process. Adapting envelope method to diagnostics and the
analysis for milling tool materials is an important contribution to the
qualitative and quantitative characterization of milling capacity and a
step by modeling the three-dimensional cutting process. An
experimental protocol was designed and developed for the
acquisition, processing and analyzing three-dimensional signal. The
vibration envelope analysis is proposed to detect the cutting capacity
of the tool with the optimization application of cutting parameters.
The research is focused on Hilbert transform optimization to evaluate
the dynamic behavior of the machine/ tool/workpiece.
Abstract: In this study, an analysis has been performed for
heat and mass transfer of a steady laminar boundary-layer flow
of a viscous flow past a nonlinearly stretching sheet.
Parameters n, Ec, k0, Sc represent the dominance of the
nonlinearly effect, viscous effect, radiation effect and mass
transfer effect which have presented in governing equations,
respectively. The similarity transformation and the
finite-difference method have been used to analyze the present
problem.
Abstract: This paper presents an improved variable ordering method to obtain the minimum number of nodes in Reduced Ordered Binary Decision Diagrams (ROBDD). The proposed method uses the graph topology to find the best variable ordering. Therefore the input Boolean function is converted to a unidirectional graph. Three levels of graph parameters are used to increase the probability of having a good variable ordering. The initial level uses the total number of nodes (NN) in all the paths, the total number of paths (NP) and the maximum number of nodes among all paths (MNNAP). The second and third levels use two extra parameters: The shortest path among two variables (SP) and the sum of shortest path from one variable to all the other variables (SSP). A permutation of the graph parameters is performed at each level for each variable order and the number of nodes is recorded. Experimental results are promising; the proposed method is found to be more effective in finding the variable ordering for the majority of benchmark circuits.
Abstract: Stress analysis of functionally graded composite plates
composed of ceramic, functionally graded material and metal layers is
investigated using 3-D finite element method. In FGM layer, material
properties are assumed to be varied continuously in the thickness
direction according to a simple power law distribution in terms of the
volume fraction of a ceramic and metal. The 3-D finite element model
is adopted by using an 18-node solid element to analyze more
accurately the variation of material properties in the thickness
direction. Numerical results are compared for three types of materials.
In the analysis, the tensile and the compressive stresses are
summarized for various FGM thickness ratios, volume fraction
distributions, geometric parameters and mechanical loads.
Abstract: The transient analysis of a queuing system with fixed-size batch Poisson arrivals and a single server with exponential service times is presented. The focus of the paper is on the use of the functions that arise in the analysis of the transient behaviour of the queuing system. These functions are shown to be a generalization of the modified Bessel functions of the first kind, with the batch size B as the generalizing parameter. Results for the case of single-packet arrivals are obtained first. The similarities between the two families of functions are then used to obtain results for the general case of batch arrival queue with a batch size larger than one.
Abstract: In this paper, Zinc Oxide (ZnO) thin films are deposited on glass substrate by sol-gel method. The ZnO thin films with well defined orientation were acquired by spin coating of zinc acetate dehydrate monoethanolamine (MEA), de-ionized water and isopropanol alcohol. These films were pre-heated at 275°C for 10 min and then annealed at 350°C, 450°C and 550°C for 80 min. The effect of annealing temperature and different thickness on structure and surface morphology of the thin films were verified by Atomic Force Microscopy (AFM). It was found that there was a significant effect of annealing temperature on the structural parameters of the films such as roughness exponent, fractal dimension and interface width. Thin films also were characterizied by X-ray Diffractometery (XRD) method. XRD analysis revealed that the annealed ZnO thin films consist of single phase ZnO with wurtzite structure and show the c-axis grain orientation. Increasing annealing temperature increased the crystallite size and the c-axis orientation of the film after 450°C. Also In this study, ZnO thin films in different thickness have been prepared by sol-gel method on the glass substrate at room temperature. The thicknesses of films are 100, 150 and 250 nm. Using fractal analysis, morphological characteristics of surface films thickness in amorphous state were investigated. The results show that with increasing thickness, surface roughness (RMS) and lateral correlation length (ξ) are decreased. Also, the roughness exponent (α) and growth exponent (β) were determined to be 0.74±0.02 and 0.11±0.02, respectively.
Abstract: The advantage of solving the complex nonlinear
problems by utilizing fuzzy logic methodologies is that the
experience or expert-s knowledge described as a fuzzy rule base can
be directly embedded into the systems for dealing with the problems.
The current limitation of appropriate and automated designing of
fuzzy controllers are focused in this paper. The structure discovery
and parameter adjustment of the Branched T-S fuzzy model is
addressed by a hybrid technique of type constrained sparse tree
algorithms. The simulation result for different system model is
evaluated and the identification error is observed to be minimum.
Abstract: The Automatic Speech Recognition (ASR) applied to
Arabic language is a challenging task. This is mainly related to the
language specificities which make the researchers facing multiple
difficulties such as the insufficient linguistic resources and the very
limited number of available transcribed Arabic speech corpora. In
this paper, we are interested in the development of a HMM-based
ASR system for Standard Arabic (SA) language. Our fundamental
research goal is to select the most appropriate acoustic parameters
describing each audio frame, acoustic models and speech recognition
unit. To achieve this purpose, we analyze the effect of varying frame
windowing (size and period), acoustic parameter number resulting
from features extraction methods traditionally used in ASR, speech
recognition unit, Gaussian number per HMM state and number of
embedded re-estimations of the Baum-Welch Algorithm. To evaluate
the proposed ASR system, a multi-speaker SA connected-digits
corpus is collected, transcribed and used throughout all experiments.
A further evaluation is conducted on a speaker-independent continue
SA speech corpus. The phonemes recognition rate is 94.02% which is
relatively high when comparing it with another ASR system
evaluated on the same corpus.
Abstract: The Yazd-Ardakan basin in Central Iran has two separated aquifers. The shallow unconfined aquifer is supplies 40 Qanats. The deep saturated confined aquifer is the main water storage. Due to over-withdrawal, water table has been decreasing during last 25 years. Recent study shows that the shortage of the aquifer is about 16 meters and land subsidence is 0.5 - 1.2 meters. Long deep cracks are found just above the aquifer and devour the irrigation water and floods. Although the most cracks direction is NW-SE and could be compared to the main direction of YA basin, there is no direct evidence for relation between land subsidence and the huge cracks. Large-scale water pumping has been decreased the water pressure in aquifer. The pressure decline disturbed the balance and increased the pressure of overlying sediments. So porosity decreased and compaction started. Then, sediments compaction developed and made land subsidence and some huge cracks slowly.
Abstract: The problem of manipulator control is a highly
complex problem of controlling a system which is multi-input, multioutput,
non-linear and time variant. In this paper some adaptive
fuzzy, and a new hybrid fuzzy control algorithm have been
comparatively evaluated through simulations, for manipulator
control. The adaptive fuzzy controllers consist of self-organizing,
self-tuning, and coarse/fine adaptive fuzzy schemes. These
controllers are tested for different trajectories and for varying
manipulator parameters through simulations. Various performance
indices like the RMS error, steady state error and maximum error are
used for comparison. It is observed that the self-organizing fuzzy
controller gives the best performance. The proposed hybrid fuzzy
plus integral error controller also performs remarkably well, given its
simple structure.
Abstract: This paper addresses modeling and optimization of process parameters in powder mixed electrical discharge machining (PMEDM). The process output characteristics include metal removal rate (MRR) and electrode wear rate (EWR). Grain size of Aluminum powder (S), concentration of the powder (C), discharge current (I) pulse on time (T) are chosen as control variables to study the process performance. The experimental results are used to develop the regression models based on second order polynomial equations for the different process characteristics. Then, a genetic algorithm (GA) has been employed to determine optimal process parameters for any desired output values of machining characteristics.
Abstract: This paper deals with analysis of flexural stiffness,
indentation and their energies in three point loading of sandwich
beams with composite faces from Eglass/epoxy and cores from
Polyurethane or PVC. Energy is consumed in three stages of
indentation in laminated beam, indentation of sandwich beam and
bending of sandwich beam. Theory of elasticity is chosen to present
equations for indentation of laminated beam, then these equations
have been corrected to offer better results. An analytical model has
been used assuming an elastic-perfectly plastic compressive behavior
of the foam core. Classical theory of beam is used to describe three
point bending. Finite element (FE) analysis of static indentation
sandwich beams is performed using the FE code ABAQUS. The
foam core is modeled using the crushable foam material model and
response of the foam core is experimentally characterized in uniaxial
compression.
Three point bending and indentation have been done
experimentally in two cases of low velocity and higher velocity
(quasi-impact) of loading. Results can describe response of beam in
terms of core and faces thicknesses, core material, indentor diameter,
energy absorbed, and length of plastic area in the testing. The
experimental results are in good agreement with the analytical and
FE analyses. These results can be used as an introduction for impact
loading and energy absorbing of sandwich structures.
Abstract: In a wind power generator using doubly fed induction
generator (DFIG), the three-phase pulse width modulation (PWM)
voltage source converter (VSC) is used as grid side converter (GSC)
and rotor side converter (RSC). The standard linear control laws
proposed for GSC provides not only instablity against comparatively
large-signal disturbances, but also the problem of stability due to
uncertainty of load and variations in parameters. In this paper, a
nonlinear controller is designed for grid side converter (GSC) of a
DFIG for wind power application. The nonlinear controller is
designed based on the input-output feedback linearization control
method. The resulting closed-loop system ensures a sufficient
stability region, make robust to variations in circuit parameters and
also exhibits good transient response. Computer simulations and
experimental results are presented to confirm the effectiveness of the
proposed control strategy.
Abstract: The new semi-experimental method for simulation of
the turbine flow meters rotation in the transitional flow has been
developed. The method is based on the experimentally established
exponential low of changing of dimensionless relative turbine gas
meter rotation frequency and meter inertia time constant. For
experimental evaluation of the meter time constant special facility
has been developed. The facility ensures instant switching of turbine
meter under test from one channel to the other channel with different
flow rate and measuring the meter response. The developed method
can be used for evaluation and predication of the turbine meters
response and dynamic error in the transitional flow with any arbitrary
law of flow rate changing. The examples of the method application
are presented.
Abstract: The objective of global optimization is to find the
globally best solution of a model. Nonlinear models are ubiquitous
in many applications and their solution often requires a global
search approach; i.e. for a function f from a set A ⊂ Rn to
the real numbers, an element x0 ∈ A is sought-after, such that
∀ x ∈ A : f(x0) ≤ f(x). Depending on the field of application,
the question whether a found solution x0 is not only a local minimum
but a global one is very important.
This article presents a probabilistic approach to determine the
probability of a solution being a global minimum. The approach is
independent of the used global search method and only requires a
limited, convex parameter domain A as well as a Lipschitz continuous
function f whose Lipschitz constant is not needed to be known.
Abstract: This paper presents an approach which is based on the
use of supervised feed forward neural network, namely multilayer
perceptron (MLP) neural network and finite element method (FEM)
to solve the inverse problem of parameters identification. The
approach is used to identify unknown parameters of ferromagnetic
materials. The methodology used in this study consists in the
simulation of a large number of parameters in a material under test,
using the finite element method (FEM). Both variations in relative
magnetic permeability and electrical conductivity of the material
under test are considered. Then, the obtained results are used to
generate a set of vectors for the training of MLP neural network.
Finally, the obtained neural network is used to evaluate a group of
new materials, simulated by the FEM, but not belonging to the
original dataset. Noisy data, added to the probe measurements is used
to enhance the robustness of the method. The reached results
demonstrate the efficiency of the proposed approach, and encourage
future works on this subject.