Abstract: A good green building design project, designers should consider not only energy consumption, but also healthy and comfortable needs of inhabitants. In recent years, the Taiwan government paid attentions on both carbon reduction and indoor air quality issues, which be presented in the legislation of Building Codes and other regulations. Taiwan located in hot and humid climates, dampness in buildings leads to significant microbial pollution and building damage. This means that the high temperature and humidity present a serious indoor air quality issue. The interactions between vapor transfers and energy fluxes are essential for the whole building Heat Air and Moisture (HAM) response. However, a simulation tool with short calculation time, property accuracy and interface is needed for practical building design processes. In this research, we consider the vapor transfer phenomenon of building materials as well as temperature and humidity and energy consumption in a building space. The simulation bases on the EMPD method, which was performed by EnergyPlus, a simulation tool developed by DOE, to simulate the indoor moisture variation in a one-zone residential unit based on the Effective Moisture Penetration Depth Method, which is more suitable for practical building design processes.
Abstract: In this paper, the performance of three types of serial
concatenated convolutional codes (SCCC) is compared and analyzed
in additive white Gaussian noise (AWGN) channel. In Type I, only the
parity bits of outer encoder are passed to inner encoder. In Type II and
Type III, both the information bits and the parity bits of outer encoder
are transferred to inner encoder. As results of simulation, Type I shows
the best bit error rate (BER) performance at low signal-to-noise ratio
(SNR). On the other hand, Type III shows the best BER performance
at high SNR in AWGN channel. The simulation results are analyzed
using the distance spectrum.
Abstract: Different forms of interaction are an integral part of
modern courses. Traditional courses held on-campus might focus on
teacher-student interaction, or student-student interaction, or both.
However when these traditional on-campus courses are to be held as
distance courses there is a risk that these well-designed interactions
will be difficult or impossible to uphold. For example, studentstudent
interaction in traditional project assignments might not work
well if the students are scattered across the world. Thus, even a welldesigned
traditional on-site course cannot without modification be
turned into a distance course. Traditional on-site courses simply have
to be redesigned to become true distance courses. This paper
describes a structured approach which facilitates the redesign of a
traditional course into a distance course. The approach is based on
that the desired forms of course flexibility are identified, and
thereafter that the course activities are redesigned to facilitate
interaction in a distance course. The approach is making use of
known patterns of pedagogic interaction and existing guidelines for
distance education design. The approach is illustrated with an
example course in the field of information systems design.
Abstract: One of the main research methods in humanistic studies is the collection and process of data through questionnaires. This paper reports our experiences of localizing and adapting the phpESP package of electronic surveys, which led to a friendly on-line questionnaire environment offered through our department web site. After presenting the characteristics of this environment, we identify the expected benefits and present a questionnaire carried out through both the traditional and electronic way. We present the respondents' feedback and then we report the researchers' opinions.Finally, we propose ideas we intend to implement in order to further assist and enhance the research based on this web accessed,electronic questionnaire environment.
Abstract: This research attempts to study the feasibility of
augmenting an augmented reality (AR) image card on a Quick
Response (QR) code. The authors have developed a new visual tag,
which contains a QR code and an augmented AR image card. The new
visual tag has features of reading both of the revealed data of the QR
code and the instant data from the AR image card. Furthermore, a
handheld communicating device is used to read and decode the new
visual tag, and then the concealed data of the new visual tag can be
revealed and read through its visual display. In general, the QR code is
designed to store the corresponding data or, as a key, to access the
corresponding data from the server through internet. Those reveled
data from the QR code are represented in text. Normally, the AR
image card is designed to store the corresponding data in
3-Dimensional or animation/video forms. By using QR code's
property of high fault tolerant rate, the new visual tag can access those
two different types of data by using a handheld communicating device.
The new visual tag has an advantage of carrying much more data than
independent QR code or AR image card. The major findings of this
research are: 1) the most efficient area for the designed augmented AR
card augmenting on the QR code is 9% coverage area out of the total
new visual tag-s area, and 2) the best location for the augmented AR
image card augmenting on the QR code is located in the bottom-right
corner of the new visual tag.
Abstract: Double-diffusive natural convection in an open top
square cavity and heated from the side is studied numerically.
Constant temperatures and concentration are imposed along the right
and left walls while the heat balance at the surface is assumed to obey
Newton-s law of cooling. The finite difference method is used to
solve the dimensionless governing equations. The numerical results
are reported for the effect of Marangoni number, Biot number and
Prandtl number on the contours of streamlines, temperature and
concentration. The predicted results for the average Nusselt number
and Sherwood number are presented for various parametric
conditions. The parameters involved are as follows; the thermal
Marangoni number, 0 ≤ MaT ≤1000 , the solutal Marangoni number,
0 1000 c ≤ Ma ≤ , the Biot number, 0 ≤ Bi ≤ 6 , Grashof number,
5 Gr = 10 and aspect ratio 1. The study focused on both flows; thermal
dominated, N = 0.8 , and compositional dominated, N = 1.3 .
Abstract: Carbon nanotubes (CNTs) possess unique structural,
mechanical, thermal and electronic properties, and have been
proposed to be used for applications in many fields. However, to
reach the full potential of the CNTs, many problems still need to be
solved, including the development of an easy and effective
purification procedure, since synthesized CNTs contain impurities,
such as amorphous carbon, carbon nanoparticles and metal particles.
Different purification methods yield different CNT characteristics
and may be suitable for the production of different types of CNTs. In
this study, the effect of different purification chemicals on carbon
nanotube quality was investigated. CNTs were firstly synthesized by
chemical vapor deposition (CVD) of acetylene (C2H2) on a
magnesium oxide (MgO) powder impregnated with an iron nitrate
(Fe(NO3)3·9H2O) solution. The synthesis parameters were selected
as: the synthesis temperature of 800°C, the iron content in the
precursor of 5% and the synthesis time of 30 min. The liquid phase
oxidation method was applied for the purification of the synthesized
CNT materials. Three different acid chemicals (HNO3, H2SO4, and
HCl) were used in the removal of the metal catalysts from the
synthesized CNT material to investigate the possible effects of each
acid solution to the purification step. Purification experiments were
carried out at two different temperatures (75 and 120 °C), two
different acid concentrations (3 and 6 M) and for three different time
intervals (6, 8 and 15 h). A 30% H2O2 : 3M HCl (1:1 v%) solution
was also used in the purification step to remove both the metal
catalysts and the amorphous carbon. The purifications using this
solution were performed at the temperature of 75°C for 8 hours.
Purification efficiencies at different conditions were evaluated by
thermogravimetric analysis. Thermal and electrical properties of
CNTs were also determined. It was found that the obtained electrical
conductivity values for the carbon nanotubes were typical for organic
semiconductor materials and thermal stabilities were changed
depending on the purification chemicals.
Abstract: Double-diffusive steady convection in a partially
porous cavity with partially permeable walls and under the combined
buoyancy effects of thermal and mass diffusion was analysed
numerically using finite volume method.
The top wall is well insulated and impermeable while the bottom
surface is partially well insulated and impermeable and partially
submitted to constant temperature T1 and concentration C1. Constant
equal temperature T2 and concentration C2 are imposed along the
vertical surfaces of the enclosure. Mass suction/injection and
injection/suction are respectively considered at the bottom of the
porous centred partition and at one of the vertical walls.
Heat and mass transfer characteristics as streamlines and average
Nusselt numbers and Sherwood numbers were discussed for different
values of buoyancy ratio, Rayleigh number, and injection/suction
coefficient.
It is especially noted that increasing the injection factor
disadvantages the exchanges in the case of the injection while the
transfer is augmented in case of suction. On the other hand, a critical
value of the buoyancy ratio was highlighted for which heat and mass
transfers are minimized.
Abstract: A model of a system concerning one species of demersal
(inshore) fish and one of pelagic (offshore) fish undergoing fishing
restricted by marine protected areas is proposed in this paper. This
setup was based on the FISH-BE model applied to the Tabina fishery
in Zamboanga del Sur, Philippines. The components of the model
equations have been adapted from widely-accepted mechanisms in
population dynamics. The model employs Gompertz-s law of growth
and interaction on each type of protected and unprotected subpopulation.
Exchange coefficients between protected and unprotected
areas were assumed to be proportional to the relative area of the
entry region. Fishing harvests were assumed to be proportional to
both the number of fishers and the number of unprotected fish. An
extra term was included for the pelagic population to allow for the
exchange between the unprotected area and the outside environment.
The systems were found to be bounded for all parameter values. The
equations for the steady state were unsolvable analytically but the
existence and uniqueness of non-zero steady states can be proven.
Plots also show that an MPA size yielding the maximum steady state
of the unprotected population can be found. All steady states were
found to be globally asymptotically stable for the entire range of
parameter values.
Abstract: This paper examines the relationship between financial
risks and profitability of the conventional and Islamic banks in
Malaysia for the period between 1996 and 2005. The measures of
profitability that have been used in the study are the return on equity
(ROE) and return on assets (ROA) while the financial risks are credit
risk, interest rate risk and liquidity risks. This study employs panel
data regression analysis of Generalised Least Squares of fixed effects
and random effects models. It was found that credit risk has a
significant impact on ROA and ROE for the conventional as well as
the Islamic banks. The relationship between interest rate risk and ROE
were found to be weakly significant for the conventional banks and
insignificant for the Islamic banks. The effect of interest rate risk on
ROA is significant for the conventional banks. Liquidity risk was
found to have an insignificant impact on both profitability measures.
Abstract: Column leach test has been performed to examine the
behavior of leaching of sodium, calcium and potassium in landfills.
In the column leach apparatus, two different layers of contaminated
and uncontaminated soils of different height ratios (ratio of depth of
contaminated soil to the depth of uncontaminated soil) are taken.
Water is poured from an overhead tank at a particular flowrate to the
inlet of the soil column for a certain ponding depth over the
contaminated soil. Subsequent infiltration causes leaching and the
leachates are collected from the bottom of the column. The
concentrations of Na, Ca and K in the leachate are measured using
flame photometry. The experiments are further extended by changing
the rates of flow from the overhead tank to the inlet of the column in
achieving the same ponding depth. The experiments are performed
for different scenarios in which the height ratios are altered and the
variations of concentrations of Na, Ca, and K are observed. The study
brings an estimation of leaching in landfill sites for different heights
and precipitation intensity where a ponding depth is maintained over
the landfill. It has been observed that the leaching behavior of Na,
Ca, and K are not similar. Calcium exhibits highest amount of
leaching compared to Sodium and Potassium under similar
experimental conditions.
Abstract: Walking and sit to stand are activities carried out by
all the people many times during the day, but physical disabilities due
to age and diseases create needs of assistive devices to help elderly
people during their daily life. This study aims to study the different
types and mechanisms of the assistive devices. We will analyze the
limitations and the challenges faced by the researchers in this field.
We will introduce the Assistive Device developed at the Egypt-Japan
University of Science and Technology, named E-JUST Assistive
Device (EJAD). EJAD will be a low cost intelligent assistive device
to help elders in walking and sit-to-stand activities.
Abstract: In this paper, we propose the pre-processor based on
the Evidence Supporting Measure of Similarity (ESMS) filter and also
propose the unified fusion approach (UFA) based on the general
fusion machine coupled with ESMS filter, which improve the
correctness and precision of information fusion in any fields of
application. Here we mainly apply the new approach to Simultaneous
Localization And Mapping (SLAM) of Pioneer II mobile robots. A
simulation experiment was performed, where an autonomous virtual
mobile robot with sonar sensors evolves in a virtual world map with
obstacles. By comparing the result of building map according to the
general fusion machine (here DSmT-based fusing machine and
PCR5-based conflict redistributor considereded) coupling with ESMS
filter and without ESMS filter, it shows the benefit of the selection of
the sources as a prerequisite for improvement of the information
fusion, and also testifies the superiority of the UFA in dealing with
SLAM.
Abstract: This research aimed to study the market feasibility for
new brand coffee house, the case study of Thailand.. This study is a
mixed methods research combining quantitative research and the
qualitative research. Primary data 350 sets of questionnaires were
distributed, and the high quality completed questionnaires of 320 sets
returned. Research samples are identified as customers’ of Hi-end
department stores in Thailand. The sources of secondary data were
critical selected from highly reliable sources, both from public and
private sectors. The results were used to classify the customer group
into two main groups, the younger than 25 and the older than 25years
old. Results of the younger group, are give priority to the dimension
of coffee house and its services dimension more than others, then
branding dimension and the product dimension respectively. On the
other hand, the older group give the difference result as they rate the
important of the branding, coffee house and its services, then the
product respectively. Coffee consuming is not just the trend but it
has become part of people lifestyle. And the new cultures also created
by the wise businessman. Coffee was long produced and consumed in
Thailand. But it is surprisingly the hi-end brand coffee houses in Thai
market are mostly imported brands. The café business possibility for
Thai brand coffee house in Thai market were discussed in the paper.
Abstract: A lot of computer-based methods have been developed
to assess the evacuation capability (EC) of high-rise buildings.
Because softwares are time-consuming and not proper for on scene
applications, we adopted two methods, fuzzy analytic hierarchy
process (FAHP) and technique for order preference by similarity to an
ideal solution (TOPSIS), for EC assessment of a high-rise building in
Jinan. The EC scores obtained with the two methods and the
evacuation time acquired with Pathfinder 2009 for floors 47-60 of the
building were compared with each other. The results show that FAHP
performs better than TOPSIS for EC assessment of high-rise buildings,
especially in the aspect of dealing with the effect of occupant type and
distance to exit on EC, tackling complex problem with multi-level
structure of criteria, and requiring less amount of computation.
However, both FAHP and TOPSIS failed to appropriately handle the
situation where the exit width changes while occupants are few.
Abstract: Distributed Computing Systems are usually considered the most suitable model for practical solutions of many parallel algorithms. In this paper an enhanced distributed system is presented to improve the time complexity of Binary Indexed Trees (BIT). The proposed system uses multi-uniform processors with identical architectures and a specially designed distributed memory system. The analysis of this system has shown that it has reduced the time complexity of the read query to O(Log(Log(N))), and the update query to constant complexity, while the naive solution has a time complexity of O(Log(N)) for both queries. The system was implemented and simulated using VHDL and Verilog Hardware Description Languages, with xilinx ISE 10.1, as the development environment and ModelSim 6.1c, similarly as the simulation tool. The simulation has shown that the overhead resulting by the wiring and communication between the system fragments could be fairly neglected, which makes it applicable to practically reach the maximum speed up offered by the proposed model.
Abstract: Residual dye contents in textile dyeing wastewater have complex aromatic structures that are resistant to degrade in biological wastewater treatment. The objectives of this study were to determine the effectiveness of nanoscale zerovalent iron (NZVI) to decolorize Reactive Black 5 (RB5) and Reactive Red 198 (RR198) in synthesized wastewater and to investigate the effects of the iron particle size, iron dosage and solution pHs on the destruction of RB5 and RR198. Synthesized NZVI was confirmed by transmission electron microscopy (TEM), X-ray diffraction (XRD), and X-ray photoelectron spectroscopy (XPS). The removal kinetic rates (kobs) of RB5 (0.0109 min-1) and RR198 (0.0111 min-1) by 0.5% NZVI were many times higher than those of microscale zerovalent iron (ZVI) (0.0007 min-1 and 0.0008 min-1, respectively). The iron dosage increment exponentially increased the removal efficiencies of both RB5 and RR198. Additionally, lowering pH from 9 to 5 increased the decolorization kinetic rates of both RB5 and RR198 by NZVI. The destruction of azo bond (N=N) in the chromophore of both reactive dyes led to decolorization of dye solutions.
Abstract: The main objective of our study is to collect data
about the profile of the asthmatic patients in Assam and thereby have
a comprehensive knowledge of the factors influencing the asthmatic
patients of the state and their medication pattern. We developed a
search strategy to find any publication about the community based
survey asthma related and used. These to search the MEDLINE
(1996 to current literature) CINAHL DOAJ pubmed databases using
the key phrases, Asthma, Respiratory disorders, Drug therapy of
Asthma, database decision support system and asthma. The
appropriate literature was printed out from the online source and
library (Journal) source. The study was conducted through a set of
structured and non-structured questionnaires targeted on the
asthmatic patients belonging to the rural and urban areas of Assam,
during the month of Dec 2006 to July 2007, 138 cases were studied
in Gauwathi Medical College & Hospital located in Bhangagarh,
Assam in India. The demographic characteristics a factor in 138
patients with asthma with allergic rhinitis (cases) gives the detail
profile of asthmatic patient-s distribution of Assam as classified on
the basis of age and sex. It is evident from the study that male
populations (66%) are more prone to asthma as compared to the
females (34%).Another striking features that emerged from this
survey is the maximum prevalence of asthma in the age group of 20-
30 years followed by infants belonging to the age group of 7 (0.05%)
0-10years among both male and female populations of Assam. The
high incidence of asthma in the age group of 20-30 years may
probably be due to the allergy arising out of sudden exposure to dust
and pollen which the children face while playing and going to the
school. The rural females in the age group of 30-40 years are more
prone to asthma than urban females in the same age group may be
due to sex differentiation among the tribal population of the state.
Pharmacists should educate the asthmatics how to use inhalers
considering growing menace of asthma in the state. Safer drugs
should be produced in the form of aerosol so that easy administration
by the asthmatic patients and physicians of the state is possible for
curing asthma. The health centers should be more equipped with the
medicines to cure asthma in the state like Assam.
Abstract: The emergence of person-centred discourse based
around notions of 'personal development planning- and 'work'life
balance' has taken hold in education and the workplace in recent
years. This paper examines this discourse with regard to recent
developments in higher education as well as the inter-related issue of
work-life balance in occupational careers. In both cases there have
been national and trans-national policy initiatives directed towards
improving both personal opportunities and competitive advantage in
a global knowledge-based economy. However, despite an increasing
concern with looking outward at this globalised educational and
employment marketplace, there is something of a paradox in
encouraging people to look inward at themselves in order to become
more self-determined. This apparent paradox is considered from a
discourse analytic perspective in terms of the ideological effects of an
increasing concern with the personal world. Specifically, it is argued
that there are tensions that emerge from a concern with an innerdirected
process of self-reflection that dissolve any engagement with
wider political issues that impact upon educational and career
development.
Abstract: The present paper deals with the experimental and
computational study of axial collapse of the aluminum metallic shells
having combined tube-frusta geometry between two parallel plates.
Shells were having bottom two third lengths as frusta and remaining
top one third lengths as tube. Shells were compressed to recognize
their modes of collapse and associated energy absorption capability.
An axisymmetric Finite Element computational model of collapse
process is presented and analysed, using a non-linear FE code
FORGE2. Six noded isoparametric triangular elements were used to
discretize the deforming shell. The material of the shells was
idealized as rigid visco-plastic. To validate the computational model
experimental and computed results of the deformed shapes and their
corresponding load-compression and energy-compression curves
were compared. With the help of the obtained results progress of the
axisymmetric mode of collapse has been presented, analysed and
discussed.