Abstract: Knowledge sharing culture contributes to a positive
working environment. Currently, there is no platform for the Faculty
of Industrial Information Technology (FIIT), Unisel academic staff to
share knowledge among them. As it is done manually, the sharing
process is through common meeting or by any offline discussions.
There is no repository for future retrieval. However, with open
source solution the development of knowledge based application may
reduce the cost tremendously. In this paper we discuss about the
domain on which this knowledge portal is being developed and also
the deployment of open source tools such as JOOMLA, PHP
programming language and MySQL. This knowledge portal is
evidence that open source tools also reliable in developing
knowledge based portal. These recommendations will be useful to
the open source community to produce more open source products in
future.
Abstract: Particle damping is a technique to reduce the
structural vibrations by means of placing small metallic particles
inside a cavity that is attached to the structure at location of high
vibration amplitudes. In this paper, we have presented an analytical
model to simulate the particle damping of two dimensional transient
vibrations in structure operating under high centrifugal loads. The
simulation results show that this technique remains effective as long
as the ratio of the dynamic acceleration of the structure to the applied
centrifugal load is more than 0.1. Particle damping increases with the
increase of particle to structure mass ratio. However, unlike to the
case of particle damping in the absence of centrifugal loads where
the damping efficiency strongly depends upon the size of the cavity,
here this dependence becomes very weak. Despite the simplicity of
the model, the simulation results are considerably in good agreement
with the very scarce experimental data available in the literature for
particle damping under centrifugal loads.
Abstract: Calcium oxide (CaO) as carbon dioxide (CO2)
adsorbent at the elevated temperature has been very well-received
thus far. The CaO can be synthesized from natural calcium carbonate
(CaCO3) sources through the reversible calcination-carbonation
process. In the study, cockle shell has been selected as CaO
precursors. The objectives of the study are to investigate the
performance of calcination and carbonation with respect to different
temperature, heating rate, particle size and the duration time. Overall,
better performance is shown at the calcination temperature of 850oC
for 40 minutes, heating rate of 20oC/min, particle size of < 0.125mm
and the carbonation temperature is at 650oC. The synthesized
materials have been characterized by nitrogen physisorption and
surface morphology analysis. The effectiveness of the synthesized
cockle shell in capturing CO2 (0.72 kg CO2/kg adsorbent) which is
comparable to the commercialized adsorbent (0.60 kg CO2/kg
adsorbent) makes them as the most promising materials for CO2
capture.
Abstract: The aim of this research was to calculate the
mechanical properties of Pd3Rh and PdRh3 ordered alloys. The
molecular dynamics (MD) simulation technique was used to obtain
temperature dependence of the energy, the Yong modulus, the shear
modulus, the bulk modulus, Poisson-s ratio and the elastic stiffness
constants at the isobaric-isothermal (NPT) ensemble in the range of
100-325 K. The interatomic potential energy and force on atoms were
calculated by Quantum Sutton-Chen (Q-SC) many body potential.
Our MD simulation results show the effect of temperature on the
cohesive energy and mechanical properties of Pd3Rh as well as
PdRh3 alloys. Our computed results show good agreement with the
experimental results where they have been available.
Abstract: An electric utility-s main concern is to plan, design, operate and maintain its power supply to provide an acceptable level of reliability to its users. This clearly requires that standards of reliability be specified and used in all three sectors of the power system, i.e., generation, transmission and distribution. That is why reliability of a power system is always a major concern to power system planners. This paper presents the reliability analysis of Bangladesh Power System (BPS). Reliability index, loss of load probability (LOLP) of BPS is evaluated using recursive algorithm and considering no de-rated states of generators. BPS has sixty one generators and a total installed capacity of 5275 MW. The maximum demand of BPS is about 5000 MW. The relevant data of the generators and hourly load profiles are collected from the National Load Dispatch Center (NLDC) of Bangladesh and reliability index 'LOLP' is assessed for the period of last ten years.
Abstract: In this paper, we present a non-blind technique of
adding the watermark to the Fourier spectral components of audio
signal in a way such that the modified amplitude does not exceed the
maximum amplitude spread (MAS). This MAS is due to individual
Discrete fourier transform (DFT) coefficients in that particular frame,
which is derived from the Energy Spreading function given by
Schroeder. Using this technique one can store double the information
within a given frame length i.e. overriding the watermark on the
host of equal length with least perceptual distortion. The watermark
is uniformly floating on the DFT components of original signal.
This helps in detecting any intentional manipulations done on the
watermarked audio. Also, the scheme is found robust to various signal
processing attacks like presence of multiple watermarks, Additive
white gaussian noise (AWGN) and mp3 compression.
Abstract: We investigate sonic cues for binaural sound localization within classrooms and present a structural model for the same. Two of the primary cues for localization, interaural time difference (ITD) and interaural level difference (ILD) created between the two ears by sounds from a particular point in space, are used. Although these cues do not lend any information about the elevation of a sound source, the torso, head, and outer ear carry out elevation dependent spectral filtering of sounds before they reach the inner ear. This effect is commonly captured in head related transfer function (HRTF) which aids in resolving the ambiguity from the ITDs and ILDs alone and helps localize sounds in free space. The proposed structural model of HRTF produces well controlled horizontal as well as vertical effects. The implemented HRTF is a signal processing model which tries to mimic the physical effects of the sounds interacting with different parts of the body. The effectiveness of the method is tested by synthesizing spatial audio, in MATLAB, for use in listening tests with human subjects and is found to yield satisfactory results in comparison with existing models.
Abstract: Overhead electrical insulators form an important link in an electric power system. Along with the traditional insulators (i.e. glass and porcelain, etc) presently the polymeric insulators are also used world widely. These polymeric insulators are very sensitive to various environmental parameters such temperature, environmental pollution, UV-radiations, etc. which seriously effect their electrical, chemical and hydrophobic properties. The UV radiation level in the central region of Saudi Arabia is high as compared to the IEC standard for the accelerated aging of the composite insulators. Commonly used suspension type of composite EPDM (Ethylene Propylene Diene Monomer) insulator was subjected to accelerated stress aging as per modified IEC standard simulating the inland arid deserts atmospheric condition and also as per IEC-61109 standard. The hydrophobic characteristics were studied by measuring the contact angle along the insulator surface before and after the accelerated aging of the samples. It was found that EPDM insulator loses it hydrophobic properties proportional to the intensity of UV irradiations and its rate of recovery is also very low as compared to Silicone Rubber insulator.KeywordsEPDM, composite insulators, accelerated aging, hydrophobicity, contact angle.
Abstract: Natural fibres have emerged as the potential reinforcement material for composites and thus gain attraction by many researchers. This is mainly due to their applicable benefits as they offer low density, low cost, renewable, biodegradability and environmentally harmless and also comparable mechanical properties with synthetic fibre composites. The properties of hybrid composites highly depends on several factors, including the interaction of fillers with the polymeric matrix, shape and size (aspect ratio), and orientation of fillers [1]. In this study, natural fibre kenaf composites and kenaf/fibreglass hybrid composites were fabricated by a combination of hand lay-up method and cold-press method. The effect of different fibre types (powder, short and long) on the tensile properties of composites is investigated. The kenaf composites with and without the addition of fibreglass were then characterized by tensile testing and scanning electron microscopy. A significant improvement in tensile strength and modulus were indicated by the introduction of long kenaf/woven fibreglass hybrid composite. However, the opposite trends are observed in kenaf powder composite. Fractographic observation shows that fibre/matrix debonding causes the fibres pull out. This phenomenon results in the fibre and matrix fracture.
Abstract: IP networks are evolving from data communication
infrastructure into many real-time applications such as video
conferencing, IP telephony and require stringent Quality of Service
(QoS) requirements. A rudimentary issue in QoS routing is to find a
path between a source-destination pair that satisfies two or more endto-
end constraints and termed to be NP hard or complete. In this
context, we present an algorithm Multi Constraint Path Problem
Version 3 (MCPv3), where all constraints are approximated and
return a feasible path in much quicker time. We present another
algorithm namely Delay Coerced Multi Constrained Routing
(DCMCR) where coerce one constraint and approximate the
remaining constraints. Our algorithm returns a feasible path, if exists,
in polynomial time between a source-destination pair whose first
weight satisfied by the first constraint and every other weight is
bounded by remaining constraints by a predefined approximation
factor (a). We present our experimental results with different
topologies and network conditions.
Abstract: A Space Vector based Pulse Width Modulation
control technique for the three-phase PWM converter is proposed in
this paper. The proposed control scheme is based on a synchronous
reference frame model. High performance and efficiency is obtained
with regards to the DC bus voltage and the power factor
considerations of the PWM rectifier thus leading to low losses.
MATLAB/SIMULINK are used as a platform for the simulations and
a SIMULINK model is presented in the paper. The results show that
the proposed model demonstrates better performance and properties
compared to the traditional SPWM method and the method improves
the dynamic performance of the closed loop drastically.
For the Space Vector based Pulse Width Modulation, Sine signal
is the reference waveform and triangle waveform is the carrier
waveform. When the value sine signal is large than triangle signal,
the pulse will start produce to high. And then when the triangular
signals higher than sine signal, the pulse will come to low. SPWM
output will changed by changing the value of the modulation index
and frequency used in this system to produce more pulse width. The
more pulse width produced, the output voltage will have lower
harmonics contents and the resolution increase.
Abstract: Any use of energy in industrial productive activities is combined with various environment impacts. Withintransportation,
this fact was not only found among land transport, railways and maritime transport, but also in the air transport industry. An effective climate protection requires strategies and measures for reducing all
greenhouses gas emissions, in particular carbon dioxide, and must
take into account the economic, ecologic and social aspects. It seem simperative now to develop and manufacture environmentally
friendly products and systems, to reduce consumption and use less
resource, and to save energy and power. Today-sproducts could
better serve these requirements taking into account the integration of
a power management system into the electrical power system.This
paper gives an overview of an approach ofpower management with
load prioritization in modernaircraft. Load dimensioning and load
management strategies on current civil aircraft will be presented and
used as a basis for the proposed approach.
Abstract: This paper presents design and implements a voltage
source inverter type space vector pulse width modulation (SVPWM)
for control a speed of induction motor. This scheme leads to be able
to adjust the speed of the motor by control the frequency and
amplitude of the stator voltage, the ratio of stator voltage to
frequency should be kept constant. The fuzzy logic controller is also
introduced to the system for keeping the motor speed to be constant
when the load varies. The experimental results in testing the 0.22 kW
induction motor from no-load condition to rated condition show the
effectiveness of the proposed control scheme.
Abstract: This paper investigates the encryption efficiency of RC6 block cipher application to digital images, providing a new mathematical measure for encryption efficiency, which we will call the encryption quality instead of visual inspection, The encryption quality of RC6 block cipher is investigated among its several design parameters such as word size, number of rounds, and secret key length and the optimal choices for the best values of such design parameters are given. Also, the security analysis of RC6 block cipher for digital images is investigated from strict cryptographic viewpoint. The security estimations of RC6 block cipher for digital images against brute-force, statistical, and differential attacks are explored. Experiments are made to test the security of RC6 block cipher for digital images against all aforementioned types of attacks. Experiments and results verify and prove that RC6 block cipher is highly secure for real-time image encryption from cryptographic viewpoint. Thorough experimental tests are carried out with detailed analysis, demonstrating the high security of RC6 block cipher algorithm. So, RC6 block cipher can be considered to be a real-time secure symmetric encryption for digital images.
Abstract: L-asparaginase was extracted from pathogenic
Escherichia coli which was isolated from urinary tract infection
patients. L-asparaginase was purified 96-fold by ultrafiltration, ion
exchange and gel filtration giving 39.19% yield with final specific
activity of 178.57 IU/mg. L-asparaginase showed 138,356±1,000
Dalton molecular weight with 31024±100 Dalton molecular mass.
Kinetic properties of enzyme resulting 1.25×10-5 mM Km and
2.5×10-3 M/min Vmax. L-asparaginase showed a maximum activity
at pH 7.5 when incubated at 37 ºC for 30 min and illustrated its full
activity (100%) after 15 min incubation at 20-37 ºC, while 70% of its
activity was lost when incubated at 60 ºC. L-asparaginase showed
cytotoxicity to U937 cell line with IC50 0.5±0.19 IU/ml, and
selectivity index (SI=7.6) about 8 time higher selectivity over the
lymphocyte cells. Therefore, the local pathogenic E. coli strains may
be used as a source of high yield of L-asparaginase to produce anti
cancer agent with high selectivity.
Abstract: The aim of this paper is to identify an optimum
control strategy of three-phase shunt active filters to minimize the total harmonic distortion factor of the supply current. A classical PIPI cascade control solution of the output current of the active filterand the voltage across the DC capacitor based on Modulus–Optimum
criterion is taken into consideration. The control system operation
has been simulated using Matlab-Simulink environment and the results agree with the theoretical expectation. It is shown that there is
an optimum value of the DC-bus voltage which minimizes the supply current harmonic distortion factor. It corresponds to the equality of the apparent power at the output of the active filter and the apparent power across the capacitor. Finally, predicted results are verified experimentally on a MaxSine active power filter.
Abstract: In the 1980s, companies began to feel the effect of three major influences on their product development: newer and innovative technologies, increasing product complexity and larger organizations. And therefore companies were forced to look for new product development methods. This paper tries to focus on the two of new product development methods (DFM and CE). The aim of this paper is to see and analyze different product development methods specifically on Design for Manufacturability and Concurrent Engineering. Companies can achieve and be benefited by minimizing product life cycle, cost and meeting delivery schedule. This paper also presents simplified models that can be modified and used by different companies based on the companies- objective and requirements. Methodologies that are followed to do this research are case studies. Two companies were taken and analysed on the product development process. Historical data, interview were conducted on these companies in addition to that, Survey of literatures and previous research works on similar topics has been done during this research. This paper also tries to show the implementation cost benefit analysis and tries to calculate the implementation time. From this research, it has been found that the two companies did not achieve the delivery time to the customer. Some of most frequently coming products are analyzed and 50% to 80 % of their products are not delivered on time to the customers. The companies are following the traditional way of product development that is sequentially design and production method, which highly affect time to market. In the case study it is found that by implementing these new methods and by forming multi disciplinary team in designing and quality inspection; the company can reduce the workflow steps from 40 to 30.
Abstract: The goal of a network-based intrusion detection
system is to classify activities of network traffics into two major
categories: normal and attack (intrusive) activities. Nowadays, data
mining and machine learning plays an important role in many
sciences; including intrusion detection system (IDS) using both
supervised and unsupervised techniques. However, one of the
essential steps of data mining is feature selection that helps in
improving the efficiency, performance and prediction rate of
proposed approach. This paper applies unsupervised K-means
clustering algorithm with information gain (IG) for feature selection
and reduction to build a network intrusion detection system. For our
experimental analysis, we have used the new NSL-KDD dataset,
which is a modified dataset for KDDCup 1999 intrusion detection
benchmark dataset. With a split of 60.0% for the training set and the
remainder for the testing set, a 2 class classifications have been
implemented (Normal, Attack). Weka framework which is a java
based open source software consists of a collection of machine
learning algorithms for data mining tasks has been used in the testing
process. The experimental results show that the proposed approach is
very accurate with low false positive rate and high true positive rate
and it takes less learning time in comparison with using the full
features of the dataset with the same algorithm.
Abstract: Mostly transforms are used for speech data
compressions which are lossy algorithms. Such algorithms are
tolerable for speech data compression since the loss in quality is not
perceived by the human ear. However the vector quantization (VQ)
has a potential to give more data compression maintaining the same
quality. In this paper we propose speech data compression algorithm
using vector quantization technique. We have used VQ algorithms
LBG, KPE and FCG. The results table shows computational
complexity of these three algorithms. Here we have introduced a new
performance parameter Average Fractional Change in Speech
Sample (AFCSS). Our FCG algorithm gives far better performance
considering mean absolute error, AFCSS and complexity as
compared to others.
Abstract: Artificial neural networks (ANN) have the ability to model input-output relationships from processing raw data. This characteristic makes them invaluable in industry domains where such knowledge is scarce at best. In the recent decades, in order to overcome the black-box characteristic of ANNs, researchers have attempted to extract the knowledge embedded within ANNs in the form of rules that can be used in inference systems. This paper presents a new technique that is able to extract a small set of rules from a two-layer ANN. The extracted rules yield high classification accuracy when implemented within a fuzzy inference system. The technique targets industry domains that possess less complex problems for which no expert knowledge exists and for which a simpler solution is preferred to a complex one. The proposed technique is more efficient, simple, and applicable than most of the previously proposed techniques.