Abstract: White concrete facade elements are widely used in
construction industry. It is challenging to achieve the desired
workability in casting of white concrete elements. Particle Matrix
model was used for proportioning the self-compacting white concrete
(SCWC) to control segregation and bleeding and to improve
workability. The paper presents how to reach the target slump flow
while controlling bleeding and segregation in SCWC. The amount of
aggregates, binders and mixing water, as well as type and dosage of
superplasticizer (SP) to be used are the major factors influencing the
properties of SCWC. Slump flow and compressive strength tests were
carried out to examine the performance of SCWC, and the results
indicate that the particle matrix model could produce successfully
SCWC controlling segregation and bleeding.
Abstract: Sol-enhanced Zn-Ni-Al2O3 nanocomposite coatings
were electroplated on mild steel by our newly developed solenhanced
electroplating method. In this method, transparent Al2O3 sol
was added into the acidic Zn-Ni bath to produced Zn-Ni-Al2O3nanocomposite
coatings. The chemical composition, microstructure and
mechanical properties of the composite and alloy coatings deposited
at two different agitation speed were investigated. The structure of all
coatings was single γ-Ni5Zn21 phase. The composite coatings possess
refined crystals with higher microhardness compared to Zn-Ni alloy
coatings. The wear resistance of Zn-Ni coatings was improved
significantly by incorporation of alumina nano particles into the
coatings. Higher agitation speed provided more uniform coatings
with smaller grain sized and slightly higher microhardness.
Considering composite coatings, high agitation speeds may facilitate
co-deposition of alumina in the coatings.
Abstract: Transportation of long turbine blades from one place
to another is a difficult process. Hence a feasibility study of
modularization of wind turbine blade was taken from structural
standpoint through finite element analysis. Initially, a non-segmented
blade is modeled and its structural behavior is evaluated to serve as
reference. The resonant, static bending and fatigue tests are simulated
in accordance with IEC61400-23 standard for comparison purpose.
The non-segmented test blade is separated at suitable location based
on trade off studies and the segments are joined with an innovative
double strap bonded joint configuration. The adhesive joint is
modeled by adopting cohesive zone modeling approach in ANSYS.
The developed blade model is analyzed for its structural response
through simulation. Performances of both the blades are found to be
similar, which indicates that, efficient segmentation of the long blade
is possible which facilitates easy transportation of the blades and on
site reassembling. The location selected for segmentation and
adopted joint configuration has resulted in an efficient segmented
blade model which proves the methodology adopted for segmentation
was quite effective. The developed segmented blade appears to be the
viable alternative considering its structural response specifically in
fatigue within considered assumptions.
Abstract: Aim of this work is to determine the theoretical and
experimental properties of filament wound glass fiber/epoxy resin
composite pipes with different winding design subjected under
bending. For determination of bending strength of composite samples
three point bending tests were conducted. Good correlation between
theoretical and experimental results has been obtained, where sample
No4 has shown the highest value of bending strength. All samples
have demonstrated matrix cracking and fiber failure followed by
layers delamination during testing. Also, it was found that smaller
winding angles lead to an increase in bending stress. From presented
results good merger between glass fibers and epoxy resin was
confirmed by SEM analysis.
Abstract: Background: Worldwide, at least 2.8 million people
die each year as a result of being overweight or obese, and 35.8
million (2.3%) of global DALYs are caused by overweight or
obesity. Obesity is acknowledged as one of the burning public
health problems reducing life expectancy and quality of life. The
body composition analysis of the university population is essential
in assessing the nutritional status, as well as the risk of developing
diseases associated with abnormal body fat content so as to make
nutritional recommendations. Objectives: The main aim was to
determine the prevalence of obesity and overweight in University
students using Anthropometric analysis and BIA methods. Material
and Methods: In this cross-sectional study, 283 university students
participated. The body composition analysis was undertaken by
using mainly: i) Anthropometric Measurement: Height, Weight,
BMI, waist circumference, hip circumference and skin fold
thickness, ii) Bio-electrical impedance was used for analysis of
body fat mass, fat percent and visceral fat which was measured by
Tanita SC-330P Professional Body Composition Analyzer. The
data so collected were compiled in MS Excel and analyzed for
males and females using SPSS 16. Results and Discussion: The
mean age of the male (n= 153) studied subjects was 25.37 ±2.39
years and females (n=130) was 22.53 ±2.31. The data of BIA
revealed very high mean fat per cent of the female subjects i.e.
30.3±6.5 per cent whereas mean fat per cent of the male subjects
was 15.60±6.02 per cent indicating a normal body fat range. The
findings showed high visceral fat of both males (12.92±3.02) and
females (16.86±4.98). BMI, BF% and WHR were higher among
females, and BMI was higher among males. The most evident
correlation was verified between BF% and WHR for female
students (r=0.902; p
Abstract: Family is a basic unit of the society and the main
source of human development. The initial aim of the family is
psychological and social support of its members and has special
developmental stages. Researches show the families who have less
cohesion, have more conflicts and maladjustments and the members
of such families are not able to communicate effectively. Family is a
system in which any inter communication is related to child rearing
patterns and can affect it. Even the child rearing styles in childhood
can determine the family communications in adulthood. Therefore,
the aim of the present research was to examine the relationship
between child-rearing styles including authoritative, authoritarian and
permissive with dimensions of family communication patterns
including the conversation and conformity. The research design was a
correlational and the population consisted of the psychology students
of Roudehen Islamic Azad University who were studying in
academic year 2013-2014. A sample of 324 students was selected
randomly from the population. The research tools were the Baumrind
Child-rearing Questionnaires and Family Communication
Patterns Inventory, The Revised Scale of Koerner and Fitzpatrick.
The result was as below: (a) there was a positive and significant
relationship between conversation orientation and authoritative style.
(b) There was no significant relationship between conversation
orientation and other child-rearing styles. (c) There was a negative
significant relationship between conformity orientation and
authoritative style. (d) There was a positive significant relationship
between conformity orientation with authoritarian and permissive
styles. (e) There was a significant relationship between 3 dimensions
of child-rearing and communication patterns.
Abstract: The paper presents new results concerning selection of
optimal information fusion formula for ensembles of C-OTDR
channels. The goal of information fusion is to create an integral
classificator designed for effective classification of seismoacoustic
target events. The LPBoost (LP-β and LP-B variants), the Multiple
Kernel Learning, and Weighing of Inversely as Lipschitz Constants
(WILC) approaches were compared. The WILC is a brand new
approach to optimal fusion of Lipschitz Classifiers Ensembles.
Results of practical usage are presented.
Abstract: Experimental studies to investigate the depth of the
scour conducted at a side-weir intersection located at the 1800 curved
flume which located Hydraulic Laboratory of Yıldız Technical
University, Istanbul, Turkey. Side weirs were located at the middle of
the straight part of the main channel. Three different lengths (25, 40
and 50 cm) and three different weir crest height (7, 10 and 12 cm) of
the side weir placed on the side weir station. There is no scour when
the material is only kaolin. Therefore, the cohesive bed was prepared
by properly mixing clay material (kaolin) with 31% sand in all
experiments. Following 24h consolidation time, in order to observe
the effect of flow intensity on the scour depth, experiments were
carried out for five different upstream Froude numbers in the range of
0.33-0.81.
As a result of this study the relation between scour depth and
upstream flow intensity as a function of time have been established.
The longitudinal velocities decreased along the side weir; towards the
downstream due to overflow over the side-weirs. At the beginning,
the scour depth increases rapidly with time and then asymptotically
approached constant values in all experiments for all side weir
dimensions as in non-cohesive sediment. Thus, the scour depth
reached equilibrium conditions. Time to equilibrium depends on the
approach flow intensity and the dimensions of side weirs. For
different heights of the weir crest, dimensionless scour depths
increased with increasing upstream Froude number. Equilibrium
scour depths which formed 7 cm side-weir crest height were obtained
higher than that of the 12 cm side-weir crest height. This means when
side-weir crest height increased equilibrium scour depths decreased.
Although the upstream side of the scour hole is almost vertical, the
downstream side of the hole is inclined.
Abstract: This study aimed to investigate the magnetic resonance
(MR) signal enhancement ratio (ER) of contrast-enhanced MR
angiography (CE-MRA) in normal rats with gadobenate dimeglumine
(Gd-BOPTA) using a clinical 3T scanner and an extremity coil. The
relaxivities of Gd-BOPTA with saline only and with 4.5% human
serum albumin (HSA) were also measured. Compared with
Gadolinium diethylenetriaminepentaacetic acid (Gd-DTPA),
Gd-BOPTA had higher relaxivities. The maximum ER of aorta (ERa),
kidney, liver and muscle with Gd-BOPTA were higher than those with
Gd-DTPA. The maximum ERa appeared at 1.2 min and decayed to half
at 10 min after Gd-BOPTA injection. This information is helpful for
the design of CE-MRA study of rats.
Abstract: Plasmin plays an important role in the human
circulatory system owing to its catalytic ability of fibrinolysis. The
immediate injection of plasmin in patients of strokes has intrigued
many scientists to design vectors that can transport plasmin to the
desired location in human body. Here we predict the structure of
human plasmin and investigate the interaction of plasmin with the
gold-nanoparticle.
Because the crystal structure of plasminogen has been solved, we
deleted N-terminal domain (Pan-apple domain) of plasminogen and
generate a mimic of the active form of this enzyme (plasmin). We
conducted a simulated annealing process on plasmin and discovered a
very large conformation occurs. Kringle domains 1, 4 and 5 had been
observed to leave its original location relative to the main body of the
enzyme and the original doughnut shape of this enzyme has been
transformed to a V-shaped by opening its two arms. This observation
of conformational change is consistent with the experimental results of
neutron scattering and centrifugation.
We subsequently docked the plasmin on the simulated gold surface
to predict their interaction. The V-shaped plasmin could utilize its
Kringle domain and catalytic domain to contact the gold surface.
Our findings not only reveal the flexibility of plasmin structure but
also provide a guide for the design of a plasmin-gold nanoparticle.
Abstract: Al6061 alloy base matrix, reinforced with particles of
silicon carbide (10 wt %) and Graphite powder (1wt%), known as
hybrid composites have been fabricated by liquid metallurgy route
(stir casting technique) and optimized at different parameters like
applied load, sliding speed and sliding distance by taguchi method. A
plan of experiment generated through taguchi technique was used to
perform experiments based on L27 orthogonal array. The developed
ANOVA and regression equations are used to find the optimum
coefficient of friction and wear under the influence of applied load,
sliding speed and sliding distance. On the basis of “smaller the best”
the dry sliding wear resistance was analysed and finally confirmation
tests were carried out to verify the experimental results.
Abstract: This research paper presents highly optimized barrel
shifter at 22nm Hi K metal gate strained Si technology node. This
barrel shifter is having a unique combination of static and dynamic
body bias which gives lowest power delay product. This power delay
product is compared with the same circuit at same technology node
with static forward biasing at ‘supply/2’ and also with normal reverse
substrate biasing and still found to be the lowest. The power delay
product of this barrel sifter is .39362X10-17J and is lowered by
approximately 78% to reference proposed barrel shifter at 32nm bulk
CMOS technology. Power delay product of barrel shifter at 22nm Hi
K Metal gate technology with normal reverse substrate bias is
2.97186933X10-17J and can be compared with this design’s PDP of
.39362X10-17J. This design uses both static and dynamic substrate
biasing and also has approximately 96% lower power delay product
compared to only forward body biased at half of supply voltage. The
NMOS model used are predictive technology models of Arizona state
university and the simulations to be carried out using HSPICE
simulator.
Abstract: This paper investigates and compares the community
support for tourism development between two groups of minority
ethnic descendants in Malacca, Malaysia, namely the Baba-Nyonya
and Portuguese. A descriptive research design using a quantitative
method with self-reported and self-administered questionnaires
through across-sectional approach was applied. Through the
descriptive and inferential statistics, some significantly useful
insights pertaining to the issue investigated were obtained. The
research outcomes indicate that the sense of community is somewhat
more effective in small communities in terms of togetherness,
closeness and a sense of belonging compared to the slightly bigger
minority group. In addition, the sense of community attributes
through membership, influence, integration and shared emotional
connections contributes to community participation in tourism
development regardless of which ethnic group one belongs to.
Abstract: Mass media campaigns against obesity are often
designed to impact large audiences. This usually means that their
audience is defined based on general demographic characteristics like
age, gender, occupation etc., not taking into account psychographics
like behavior, motivations, wants, etc. Using psychographics, as the
base for the audience segmentation, is a common practice in case of
successful campaigns, as it allows developing more relevant
messages. It also serves a purpose of identifying key segments, those
that generate the best return on investment. For a health campaign,
that would be segments that have the best chance of being converted
into healthy lifestyle at the lowest cost. This paper presents the
limitations of the demographic targeting, based on the findings from
the reception study of IMSS (Mexican Social Security Institute) antiobesity
TV commercials and proposes mothers as the first level of
segmentation, in the process of identifying the key segment for these
campaigns.
Abstract: Purpose: The study aimed to assess the depressant or
antidepressant effects of several Nonsteroidal Anti-Inflammatory
Drugs (NSAIDs) in mice: the selective cyclooxygenase-2 (COX-2)
inhibitor meloxicam, and the non-selective COX-1 and COX-2
inhibitors lornoxicam, sodium metamizole, and ketorolac. The
current literature data regarding such effects of these agents are
scarce.
Materials and methods: The study was carried out on NMRI mice
weighing 20-35 g, kept in a standard laboratory environment. The
study was approved by the Ethics Committee of the University of
Medicine and Pharmacy „Carol Davila”, Bucharest. The study agents
were injected intraperitoneally, 10 mL/kg body weight (bw) 1 hour
before the assessment of the locomotor activity by cage testing (n=10
mice/ group) and 2 hours before the forced swimming tests (n=15).
The study agents were dissolved in normal saline (meloxicam,
sodium metamizole), ethanol 11.8% v/v in normal saline (ketorolac),
or water (lornoxicam), respectively. Negative and positive control
agents were also given (amitryptilline in the forced swimming test).
The cage floor used in the locomotor activity assessment was divided
into 20 equal 10 cm squares. The forced swimming test involved
partial immersion of the mice in cylinders (15/9cm height/diameter)
filled with water (10 cm depth at 28C), where they were left for 6
minutes. The cage endpoint used in the locomotor activity assessment
was the number of treaded squares. Four endpoints were used in the
forced swimming test (immobility latency for the entire 6 minutes,
and immobility, swimming, and climbing scores for the final 4
minutes of the swimming session), recorded by an observer that was
„blinded” to the experimental design. The statistical analysis used the
Levene test for variance homogeneity, ANOVA and post-hoc
analysis as appropriate, Tukey or Tamhane tests.
Results: No statistically significant increase or decrease in the
number of treaded squares was seen in the locomotor activity
assessment of any mice group. In the forced swimming test,
amitryptilline showed an antidepressant effect in each experiment, at
the 10 mg/kg bw dosage. Sodium metamizole was depressant at 100
mg/kg bw (increased the immobility score, p=0.049, Tamhane test),
but not in lower dosages as well (25 and 50 mg/kg bw). Ketorolac
showed an antidepressant effect at the intermediate dosage of 5
mg/kg bw, but not so in the dosages of 2.5 and 10 mg/kg bw,
respectively (increased the swimming score, p=0.012, Tamhane test).
Meloxicam and lornoxicam did not alter the forced swimming
endpoints at any dosage level.
Discussion: 1) Certain NSAIDs caused changes in the forced
swimming patterns without interfering with locomotion. 2) Sodium
metamizole showed a depressant effect, whereas ketorolac proved
antidepressant. Conclusion: NSAID-induced mood changes are not
class effects of these agents and apparently are independent of the
type of inhibited cyclooxygenase (COX-1 or COX-2).
Disclosure: This paper was co-financed from the European Social
Fund, through the Sectorial Operational Programme Human Resources Development 2007-2013, project number POSDRU /159
/1.5 /S /138907 "Excellence in scientific interdisciplinary research,
doctoral and postdoctoral, in the economic, social and medical fields
-EXCELIS", coordinator The Bucharest University of Economic
Studies.
Abstract: Advanced treatments such as forward osmosis (FO)
can be used to separate or reject nutrients from secondary treated
effluents. Forward osmosis uses the chemical potential across the
membrane, which is the osmotic pressure gradient, to induce water to
flow through the membrane from a feed solution (FS) into a draw
solution (DS). The performance of FO is affected by the membrane
characteristics, composition of the FS and DS, and operating
conditions. The aim of this study was to investigate the optimum
velocity and temperature for nutrient rejection and water flux
performance in FO treatments. MgCl2 was used as the DS in the FO
process. The results showed that higher cross flow velocities yielded
higher water fluxes. High rejection of nutrients was achieved by using
a moderate cross flow velocity at 0.25 m/s. Nutrient rejection was
insensitive to temperature variation, whereas water flux was
significantly impacted by it. A temperature of 25°C was found to be
good for nutrient rejection.
Abstract: Brass terminal, one of the several crude oil and
petroleum products storage/handling facilities in the Niger Delta was
built in the 1980s. Activities at this site, over the years, released
crude oil into this 3 m-deep, 1500 m-long canal lying adjacent to the
terminal with oil floating on it and its sediment heavily polluted. To
ensure effective clean-up, three major activities were planned: site
characterization, bioremediation pilot plant construction and testing
and full-scale bioremediation of contaminated sediment / bank soil by
land farming. The canal was delineated into 12 lots and each
characterized, with reference to the floating oily phase, contaminated
sediment and canal bank soil. As a result of site characterization, a
pilot plant for on-site bioremediation was designed and a treatment
basin constructed for carrying out pilot bioremediation test.
Following a designed sampling protocol, samples from this pilot
plant were collected for analysis at two laboratories as a quality
assurance / quality control check. Results showed that Brass Canal
upstream is contaminated with dark, thick and viscous oily film with
characteristic hydrocarbon smell while downstream, thin oily film
interspersed with water was observed. Sediments were observed to be
dark with mixture of brownish sandy soil with TPH ranging from
17,800 mg/kg in Lot 1 to 88,500 mg/kg in Lot 12 samples. Brass
Canal bank soil was observed to be sandy from ground surface to 3m,
below ground surface (bgs) it was silty-sandy and brownish while
subsurface soil (4-10m bgs) was sandy-clayey and whitish/grayish
with typical hydrocarbon smell. Preliminary results obtained so far
have been very promising but were proprietary. This project is
considered, to the best of technical literature knowledge, the first
large-scale on-site bioremediation project in the Niger Delta region,
Nigeria.
Abstract: In this paper, we propose a system for preventing gas
risks through the use of wireless communication modules and
intelligent gas safety appliances. Our system configuration consists of
an automatic extinguishing system, detectors, a wall-pad, and a
microcomputer controlled micom gas meter to monitor gas flow and
pressure as well as the occurrence of earthquakes. The automatic fire
extinguishing system checks for both combustible gaseous leaks and
monitors the environmental temperature, while the detector array
measures smoke and CO gas concentrations. Depending on detected
conditions, the micom gas meter cuts off an inner valve and generates
a warning, the automatic fire-extinguishing system cuts off an external
valve and sprays extinguishing materials, or the sensors generate
signals and take further action when smoke or CO are detected.
Information on intelligent measures taken by the gas safety appliances
and sensors are transmitted to the wall-pad, which in turn relays this as
real time data to a server that can be monitored via an external network
(BcN) connection to a web or mobile application for the management
of gas safety. To validate this smart-home gas management system, we
field-tested its suitability for use in Korean apartments under several
scenarios.
Abstract: Dielectric ceramic samples in the BaO-Re2O3-TiO2
ternary system were synthesized with structural formula Ba2-
xRe4+2x/3Ti8O24 where Re= rare earth metal and Re= Sm and La where
x varies from 0.0 to 0.6 with step size 0.1. Polycrystalline samples
were prepared by the conventional solid state reaction technique. The
dielectric, electrical and impedance analysis of all the samples in the
frequency range 1KHz- 1MHz at room temperature (25°C) have been
done to get the understanding of electrical conduction and dielectric
relaxation and their correlation. Dielectric response of the samples at
lower frequencies shows dielectric dispersion while at higher
frequencies it shows dielectric relaxation. The ac conductivity is well
fitted by the Jonscher law. The spectroscopic data in the impedance
plane confirms the existence of grain contribution to the relaxation.
All the properties are found out to be function of frequency as well as
the amount of substitution.
Abstract: This paper presents a rank correlation curve. The
traditional correlation coefficient is valid for both continuous
variables and for integer variables using rank statistics. Since
the correlation coefficient has already been established in rank
statistics by Spearman, such a calculation can be extended to
the correlation curve.
This paper presents two survey questions. The survey
collected non-continuous variables. We will show weak to
moderate correlation. Obviously, one question has a negative
effect on the other. A review of the qualitative literature
can answer which question and why. The rank correlation
curve shows which collection of responses has a positive
slope and which collection of responses has a negative slope.
Such information is unavailable from the flat, ”first-glance”
correlation statistics.