Abstract: Laura Island, which is located about 50 km away from
downtown, is a source of water supply in Majuro atoll, which is the
capital of the Republic of the Marshall Islands. Low and flat Majuro
atoll has neither river nor lake. It is very important for Majuro atoll to
ensure the conservation of its water resources. However, upconing,
which is the process of partial rising of the freshwater-saltwater
boundary near the water-supply well, was caused by the excess
pumping from it during the severe drought in 1998. Upconing will
make the water usage of the freshwater lens difficult. Thus,
appropriate water usage is required to prevent up coning in the
freshwater lens because there is no other water source during drought. Numerical simulation of water usage applying SEAWAT model
was conducted at the central part of Laura Island, including the water
supply well, which was affected by upconing. The freshwater lens was
created as a result of infiltration of consistent average rainfall. The lens
shape was almost the same as the one in 1985. 0 of monthly rainfall
and variable daily pump discharge were used to calculate the
sustainable pump discharge from the water supply well. Consequently,
the total amount of pump discharge was increased as the daily pump
discharge was increased, indicating that it needs more time to recover
from upconing. Thus, a pump standard to reduce the pump intensity is
being proposed, which is based on numerical simulation concerning
the occurrence of the up-coning phenomenon in Laura Island during
the drought.
Abstract: The Haussmannization plan of Cairo in 1867 formed a
regular network of roundabout spaces, though deteriorated at present.
The method of identifying the spatial structure of roundabout Cairo
for conservation matches the voronoi diagram with the space syntax
through their geometrical property of spatial convexity. In this
initiative, the primary convex hull of first-order voronoi adopts the
integral and control measurements of space syntax on Cairo’s
roundabout generators. The functional essence of royal palaces
optimizes the roundabout structure in terms of spatial measurements
and the symbolic voronoi projection of 'Tahrir Roundabout' over the
Giza Nile and Pyramids. Some roundabouts of major public and
commercial landmarks surround the pole of 'Ezbekia Garden' with a
higher control than integral measurements, which filter the new
spatial structure from the adjacent traditional town. Nevertheless, the
least integral and control measures correspond to the voronoi
contents of pollutant workshops and the plateau of old Cairo Citadel
with the visual compensation of new royal landmarks on top.
Meanwhile, the extended suburbs of infinite voronoi polygons
arrange high control generators of chateaux housing in 'garden city'
environs. The point pattern of roundabouts determines the
geometrical characteristics of voronoi polygons. The measured
lengths of voronoi edges alternate between the zoned short range at
the new poles of Cairo and the distributed structure of longer range.
Nevertheless, the shortest range of generator-vertex geometry
concentrates at 'Ezbekia Garden' where the crossways of vast Cairo
intersect, which maximizes the variety of choice at different spatial
resolutions. However, the symbolic 'Hippodrome' which is the largest
public landmark forms exclusive geometrical measurements, while
structuring a most integrative roundabout to parallel the royal syntax.
Overview of the symbolic convex hull of voronoi with space syntax
interconnects Parisian Cairo with the spatial chronology of scattered
monuments to conceive one universal Cairo structure. Accordingly,
the approached methodology of 'voronoi-syntax' prospects the future
conservation of roundabout Cairo at the inferred city-level concept.
Abstract: Coal fly ash, an industrial by product of coal
combustion thermal power plants is considered as a hazardous
material and its improper disposal has become an environmental
issue. On the other hand, manufacturing conventional clay bricks
involves on consumption of large amount of clay and leads
substantial depletion of topsoil. This paper unveils the possibility of
using fly ash as a partial replacement of clay for brick manufacturing
considering the local technology practiced in Bangladesh. The effect
of fly ash with different replacing ratio (0%, 20%, 30%, 40%, and
50% by volume) of clay on properties of bricks was studied. Bricks
were made in the field parallel to ordinary bricks marked with
specific number for different percentage to identify them at time of
testing. No physical distortion is observed in fly ash brick after
burning in the kiln. Results from laboratory test show that
compressive strength of brick is decreased with the increase of fly
ash and maximum compressive strength is found to be 19.6 MPa at
20% of fly ash. In addition, water absorption of fly ash brick is
increased with the increase of fly ash. The abrasion value and
Specific gravity of coarse aggregate prepared from brick with fly ash
also studied and the results of this study suggests that 20% fly ash
can be considered as the optimum fly ash content for producing good
quality bricks utilizing present practiced technology.
Abstract: Mechanical behavior of 6082T6 aluminum is
investigated at different temperatures. The strain rate sensitivity is
investigated at different temperatures on the grain size variants. The
sensitivity of the measured grain size variants on 3-D grain is
discussed. It is shown that the strain rate sensitivities are negative for
the grain size variants during the deformation of nanostructured
materials. It is also observed that the strain rate sensitivities vary in
different ways with the equivalent radius, semi minor axis radius,
semi major axis radius and major axis radius. From the obtained
results, it is shown that the variation of strain rate sensitivity with
temperature suggests that the strain rate sensitivity at the low and the
high temperature ends of the 6082T6 aluminum range is different.
The obtained results revealed transition at different temperature from
negative strain rate sensitivity as temperature increased on the grain
size variants.
Abstract: The ASEAN Economic Community (AEC) is the goal
of regional economic integration by 2015. In the region, tourism is an
activity that is important, especially as a source of foreign currency, a
source of employment creation and a source of income bringing to the
region. Given the complexity of the issues entailing the concept of
sustainable tourism, this paper tries to assess tourism sustainability
with the ASEAN, based on a number of quantitative indicators for all
the ten economies, Thailand, Myanmar, Laos, Vietnam, Malaysia,
Singapore, Indonesia, Philippines, Cambodia, and Brunei. The
methodological framework will provide a number of benchmarks of
tourism activities in these countries. They include identification of the
dimensions; for example, economic, socio-ecologic, infrastructure
and indicators, method of scaling, chart representation and evaluation
on Asian countries. This specification shows that a similar level of
tourism activity might introduce different implementation in the
tourism activity and might have different consequences for the socioecological
environment and sustainability. The heterogeneity of
developing countries exposed briefly here would be useful to detect
and prepare for coping with the main problems of each country in
their tourism activities, as well as competitiveness and value creation
of tourism for ASEAN economic community, and will compare with
other parts of the world.
Abstract: Ensuring of continuity of business is basic strategy of
every company. Continuity of organization activities includes
comprehensive procedures that help in solving unexpected situations
of natural and anthropogenic character (for example flood, blaze,
economic situations). Planning of continuity operations is a process
that helps identify critical processes and implement plans for the
security and recovery of key processes. The aim of this article is to
demonstrate application of system approach to managing business
continuity called business continuity management systems in military
issues. This article describes the life cycle of business continuity
management which is based on the established cycle PDCA (Plan-
Do-Check-Act). After this is carried out by activities which are
making by University of Defence during activation of forces and
means of the integrated rescue system in case of emergencies -
accidents at a nuclear power plant in Czech Republic. Activities of
various stages of deployment earmarked forces and resources are
managed and evaluated by using MCMS application (Military
Continuity Management System).
Abstract: The myocardium is composed of specialized muscle
which relies mainly on fatty acid and sugar metabolism and it is
widely contribute to the heart functioning. The changes of the cardiac
energy-producing system during heart failure have been proved using
autoradiography techniques. This study focused on evaluating sugar
and fatty acid metabolism in myocardium as cardiac energy getting
system using heart-accumulated radiopharmaceuticals. Two sets of
autoradiographs of heart cross sections of Lewis male rats were
analyzed and the time- accumulation curve obtained with use of the
MATLAB image processing software to evaluate fatty acid and sugar
metabolic functions.
Abstract: Over the past few decades, manufacturing has evolved
from a more labor-intensive set of mechanical processes to a
sophisticated set of information based technology processes. With the
existence of various advanced manufacturing technologies (AMTs),
more and more functions or jobs are performed by these machines
instead of human labour. This study was undertaken in order to
research the extent of AMTs adoption in manufacturing companies in
Kenya. In order to investigate a survey was conducted via
questionnaires that were sent to 183 selected AMT manufacturing
companies in Kenya. 92 companies responded positively. All the
surveyed companies were found to have a measure of investment in
at least two of the 14 types of AMTs investigated. In general the
company surveyed showed that the level of AMT adoption in Kenya
is very low with investments levels at a mean of 2.057 and
integration levels at a mean of 1.639 in a scale of 1-5.
Abstract: We regard forecasting of energy consumption by
private production areas of a large industrial facility as well as by the
facility itself. As for production areas, the forecast is made based on
empirical dependencies of the specific energy consumption and the
production output. As for the facility itself, implementation of the
task to minimize the energy consumption forecasting error is based
on adjustment of the facility’s actual energy consumption values
evaluated with the metering device and the total design energy
consumption of separate production areas of the facility. The
suggested procedure of optimal energy consumption was tested based
on the actual data of core product output and energy consumption by
a group of workshops and power plants of the large iron and steel
facility. Test results show that implementation of this procedure gives
the mean accuracy of energy consumption forecasting for winter
2014 of 0.11% for the group of workshops and 0.137% for the power
plants.
Abstract: Gladiolus is an important cash crop and is grown
mainly for its elegant spikes. Traditionally the gladiolus corms are
planted manually which is very tedious, time consuming and labor
intensive operation. So far, there is no planter available for planting
of gladiolus corms. With a view to mechanize the planting operation
of this horticultural crop, a prototype of 4-row gladiolus planter was
developed and its performance was evaluated in-situ condition. Cupchain
type metering device was used to place each single gladiolus
corm in furrow at required spacing while planting. Three levels of
corm spacing viz 15, 20 and 25 cm and four levels of forward speed
viz 1.0, 1.5, 2.0 and 2.5 km/h was taken as evaluation parameter for
the planter. The performance indicators namely corm spacing in each
row, coefficient of uniformity, missing index, multiple index, quality
of feed index, number of corms per meter length, mechanical damage
to the corms etc. were determined during the field test. The data was
statistically analyzed using Completely Randomized Design (CRD)
for testing the significance of the parameters. The result indicated
that planter was able to drop the corms at required nominal spacing
with minor variations. The highest deviation from the mean corm
spacing was observed as 3.53 cm with maximum coefficient of
variation as 13.88%. The highest missing and quality of feed indexes
were observed as 6.33% and 97.45% respectively with no multiples.
The performance of the planter was observed better at lower forward
speed and wider corm spacing. The field capacity of the planter was
found as 0.103 ha/h with an observed field efficiency of 76.57%.
Abstract: This paper introduces a signal monitoring program
developed with a view to helping electrical engineering students get
familiar with sensors with digital output. Because the output of digital
sensors cannot be simply monitored by a measuring instrument such as
an oscilloscope, students tend to have a hard time dealing with digital
sensors. The monitoring program runs on a PC and communicates with
an MCU that reads the output of digital sensors via an asynchronous
communication interface. Receiving the sensor data from the MCU,
the monitoring program shows time and/or frequency domain plots of
the data in real time. In addition, the monitoring program provides a
serial terminal that enables the user to exchange text information with
the MCU while the received data is plotted. The user can easily
observe the output of digital sensors and configure the digital sensors
in real time, which helps students who do not have enough experiences
with digital sensors. Though the monitoring program was programmed
in the Matlab programming language, it runs without the Matlab since
it was compiled as a standalone executable.
Abstract: The use of Computer Aided Design (CAD)
technologies has become pervasive in the Architecture, Engineering
and Construction (AEC) industry. This has led to its inclusion as an
important part of the training module in the curriculum for
Architecture Schools in Nigeria. This paper examines the ethical
questions that arise in the implementation of Computer Aided Design
(CAD) Content of the curriculum for Architectural education. Using
existing literature, it begins this scrutiny from the propriety of
inclusion of CAD into the education of the architect and the
obligations of the different stakeholders in the implementation
process. It also examines the questions raised by the negative use of
computing technologies as well as perceived negative influence of
the use of CAD on design creativity. Survey methodology was
employed to gather data from the Department of Architecture,
Chukwuemeka Odumegwu Ojukwu University Uli, which has been
used as a case study on how the issues raised are being addressed.
The paper draws conclusions on what will make for successful ethical
implementation.
Abstract: Considering the challenges of short product life cycles
and growing variant diversity, cost minimization and manufacturing
flexibility increasingly gain importance to maintain a competitive
edge in today’s global and dynamic markets. In this context, an
aerodynamic part feeding system for high-speed industrial assembly
applications has been developed at the Institute of Production
Systems and Logistics (IFA), Leibniz Universitaet Hannover. The
aerodynamic part feeding system outperforms conventional systems
with respect to its process safety, reliability, and operating speed. In
this paper, a multi-objective optimisation of the aerodynamic feeding
system regarding the orientation rate, the feeding velocity, and the
required nozzle pressure is presented.
Abstract: A model to predict the plastic zone size for material
under plane stress condition has been developed and verified
experimentally. The developed model is a function of crack size,
crack angle and material property (dislocation density). Simulation
and validation results show that the model developed show good
agreement with experimental results. Samples of low carbon steel
(0.035%C) with included surface crack angles of 45o, 50o, 60o, 70o
and 90o and crack depths of 2mm and 4mm were subjected to low
strain rate between 0.48 x 10-3 s-1 – 2.38 x 10-3 s-1. The mechanical
properties studied were ductility, tensile strength, modulus of
elasticity, yield strength, yield strain, stress at fracture and fracture
toughness. The experimental study shows that strain rate has no
appreciable effect on the size of plastic zone while crack depth and
crack angle plays an imperative role in determining the size of the
plastic zone of mild steel materials.
Abstract: We have studied the temporal characteristics of
bistable perception of the stimuli of two types: one involves
alterations in a perceived depth and another one has an ambiguous
content. We used the Necker lattice and lines of shadowed circles
ambiguously perceived either as spheres or holes as stimuli of the
first type. The Winson figure (the Eskimo/Indian picture) was a
stimulus of the second type. We have analyzed how often the
reversals occurred (reversal rate) and for how long each of the two
interpretations, or percepts, was observed during one presentation
(stability durations). For all three ambiguous images the reversal rate
and the stability durations had similar values, which provide another
evidence for a significant role of top-down processes in multistable
perception.
Abstract: Concurrent planning of project scheduling and
material ordering has been increasingly addressed within last decades
as an approach to improve the project execution costs. Therefore, we
have taken the problem into consideration in this paper, aiming to
maximize schedules quality robustness, in addition to minimize the
relevant costs. In this regard, a bi-objective mathematical model is
developed to formulate the problem. Moreover, it is possible to
utilize the all-unit discount for materials purchasing. The problem is
then solved by the E-constraint method, and the Pareto front is
obtained for a variety of robustness values. The applicability and
efficiency of the proposed model is tested by different numerical
instances, finally.
Abstract: The modelling of physical phenomena, such as the
earth’s free oscillations, the vibration of strings, the interaction of
atomic particles, or the steady state flow in a bar give rise to Sturm-
Liouville (SL) eigenvalue problems. The boundary applications of
some systems like the convection-diffusion equation, electromagnetic
and heat transfer problems requires the combination of Dirichlet and
Neumann boundary conditions. Hence, the incorporation of Robin
boundary condition in the analyses of Sturm-Liouville problem. This
paper deals with the computation of the eigenvalues and
eigenfunction of generalized Sturm-Liouville problems with Robin
boundary condition using the finite element method. Numerical
solution of classical Sturm–Liouville problem is presented. The
results show an agreement with the exact solution. High results
precision is achieved with higher number of elements.
Abstract: Global economy today is full of sophistication. All
over the world, business and marketing practices are undergoing
unprecedented transformation. In realization of this fact, the federal
government of Nigeria has put in place a robust transformation
agenda in order to put Nigeria in a better position to be a competitive
player and in the process transform all sectors of its economy. New
technologies, especially the Internet, are the driving force behind this
transformation. However, technology has inadvertently affected the
way businesses are done thus necessitating the acquisition of new
skills. In developing countries like Nigeria, citizens are still battling
with effective application of those technologies. Obviously, students
of business education need to acquire relevant business knowledge to
be able to transit into the world of work on graduation from school
and compete favorably in the labor market. Therefore, effective
utilization of social media by both teachers and students can help
extensively in empowering students with the needed skills. Social
media which is a group of Internet-based applications built on the
ideological foundations of Web 2.0, that allow the creation and
exchange of user generated content, and if incorporated into the
classroom experience may be the needed answer to unemployment
and poverty in Nigeria as beneficiaries can easily connect with
existing and potential enterprises and customers, engage with them
and reinforce mutual business benefits. Challenges and benefits of
social media use in education in Nigeria universities were revealed in
this study.
Abstract: This research was made during the 2015 growing
periods in the trial filed of "Research Station for Department of Field
Crops, Agricultural Faculty, Selcuk University" according to
“Randomized Blocks Design” with 3 replications. Research material
was the following pea lines; PS16, PS18, PS21, PS23, PS24, PS25,
PS36, PS47, PS49, PS51, PS54, PS58, PS67, PS69, PS71, PS73,
PS83, PS84, PS87 and PSKY and three cultivars and other 2
commercial varieties named as Bolero, Rondo and Ultrello. Some
agronomical characteristics such as plant height (cm) number of pod
per plant number of seed per pod number of seed per plant 100 seed
weight (g) and seed yield (kg ha-1) were determined. The highest seed
yield was obtained 2727.0 kg ha-1 in the PS71 line and the lowest
value was obtained 1238.0 kg ha-1 in the commercial variety of
Bolero. Results of the research implicated that the new developed
lines were superior compared with the control (commercial) varieties
by means of most of the characteristics. Nevertheless, similar
researches should be continued in different locations and years.
Abstract: This research work presents the surface
thermodynamics approach to M-TB/HIV-Human sputum
interactions. This involved the use of the Hamaker coefficient
concept as a surface energetics tool in determining the interaction
processes, with the surface interfacial energies explained using van
der Waals concept of particle interactions. The Lifshitz derivation for
van der Waals forces was applied as an alternative to the contact
angle approach which has been widely used in other biological
systems. The methodology involved taking sputum samples from
twenty infected persons and from twenty uninfected persons for
absorbance measurement using a digital Ultraviolet visible
Spectrophotometer. The variables required for the computations with
the Lifshitz formula were derived from the absorbance data. The
Matlab software tools were used in the mathematical analysis of the
data produced from the experiments (absorbance values). The
Hamaker constants and the combined Hamaker coefficients were
obtained using the values of the dielectric constant together with the
Lifshitz Equation. The absolute combined Hamaker coefficients
A132abs and A131abs on both infected and uninfected sputum samples
gave the values of A132abs = 0.21631x10-21Joule for M-TB infected
sputum and Ã132abs = 0.18825x10-21Joule for M-TB/HIV infected
sputum. The significance of this result is the positive value of the
absolute combined Hamaker coefficient which suggests the existence
of net positive van der waals forces demonstrating an attraction
between the bacteria and the macrophage. This however, implies that
infection can occur. It was also shown that in the presence of HIV,
the interaction energy is reduced by 13% conforming adverse effects
observed in HIV patients suffering from tuberculosis.