Abstract: A known iterative computational procedure is used for
internal normal ball loads calculation in statically loaded single-row,
angular-contact ball bearings, subjected to a known thrust load,
which is applied in the inner ring at the geometric bearing center line.
Numerical aspects of the iterative procedure are discussed.
Numerical examples results for a 218 angular-contact ball bearing
have been compared with those from the literature. Twenty figures
are presented showing the geometrical features, the behavior of the
convergence variables and the following parameters as functions of
the thrust load: normal ball loads, contact angle, distance between
curvature centers, and normal ball and axial deflections between the
raceways.
Abstract: In this paper, we studied some properties of geodesic on some open surfaces: Hyperboloid, Paraboloid and Funnel Surface. Geodesic equation in the v-Clairaut parameterization was calculated and reduced to definite integral. Some geodesics on some open surfaces as mention above were classified by Clairaut's relation.
Abstract: Nowadays, the focus on renewable energy and alternative fuels has increased due to increasing oil prices, environment pollution, and also concern on preserving the nature. Biodiesel has been known as an attractive alternative fuel although biodiesel produced from edible oil is very expensive than conventional diesel. Therefore, the uses of biodiesel produced from non-edible oils are much better option. Currently Jatropha biodiesel (JBD) is receiving attention as an alternative fuel for diesel engine. Biodiesel is non-toxic, biodegradable, high lubricant ability, highly renewable, and its use therefore produces real reduction in petroleum consumption and carbon dioxide (CO2) emissions. Although biodiesel has many advantages, but it still has several properties need to improve, such as lower calorific value, lower effective engine power, higher emission of nitrogen oxides (NOX) and greater sensitivity to low temperature. Exhaust gas recirculation (EGR) is effective technique to reduce NOX emission from diesel engines because it enables lower flame temperature and oxygen concentration in the combustion chamber. Some studies succeeded to reduce the NOX emission from biodiesel by EGR but they observed increasing soot emission. The aim of this study was to investigate the engine performance and soot emission by using blended Jatropha biodiesel with different EGR rates. A CI engine that is water-cooled, turbocharged, using indirect injection system was used for the investigation. Soot emission, NOX, CO2, carbon monoxide (CO) were recorded and various engine performance parameters were also evaluated.
Abstract: Existing proceeding-models for the development of mechatronic systems provide a largely parallel action in the detailed development. This parallel approach is to take place also largely independent of one another in the various disciplines involved. An approach for a new proceeding-model provides a further development of existing models to use for the development of Adaptronic Systems. This approach is based on an intermediate integration and an abstract modeling of the adaptronic system. Based on this system-model a simulation of the global system behavior, due to external and internal factors or Forces is developed. For the intermediate integration a special data management system is used. According to the presented approach this data management system has a number of functions that are not part of the "normal" PDM functionality. Therefore a concept for a new data management system for the development of Adaptive system is presented in this paper. This concept divides the functions into six layers. In the first layer a system model is created, which divides the adaptronic system based on its components and the various technical disciplines. Moreover, the parameters and properties of the system are modeled and linked together with the requirements and the system model. The modeled parameters and properties result in a network which is analyzed in the second layer. From this analysis necessary adjustments to individual components for specific manipulation of the system behavior can be determined. The third layer contains an automatic abstract simulation of the system behavior. This simulation is a precursor for network analysis and serves as a filter. By the network analysis and simulation changes to system components are examined and necessary adjustments to other components are calculated. The other layers of the concept treat the automatic calculation of system reliability, the "normal" PDM-functionality and the integration of discipline-specific data into the system model. A prototypical implementation of an appropriate data management with the addition of an automatic system development is being implemented using the data management system ENOVIA SmarTeam V5 and the simulation system MATLAB.
Abstract: In this paper, the wear of high speed steel hobs during
hobbing has been studied. The wear mechanisms are strongly
influenced by the choice of cutting speed. At moderate and high
cutting speeds three major wear mechanisms were identified:
abrasion, mild adhesive and severe adhesive. The microstructure and
wear behavior of two high speed steel grades (M2 and ASP30) has
been compared. In contrast, a variation in chemical composition or
microstructure of HSS tool material generally did not change the
dominant wear mechanism. However, the tool material properties
determine the resistance against the operating wear mechanism and
consequently the tool life. The metallographic analysis and wear
measurement at the tip of hob teeth included scanning electron
microscopy and stereoscope microscopy. Roughness profilometery is
used for measuring the gear surface roughness.
Abstract: In this paper the gradient based iterative algorithms are presented to solve the following four types linear matrix equations: (a) AXB = F; (b) AXB = F, CXD = G; (c) AXB = F s. t. X = XT ; (d) AXB+CYD = F, where X and Y are unknown matrices, A,B,C,D, F,G are the given constant matrices. It is proved that if the equation considered has a solution, then the unique minimum norm solution can be obtained by choosing a special kind of initial matrices. The numerical results show that the proposed method is reliable and attractive.
Abstract: In the present study, a numerical analysis is carried
out to investigate unsteady MHD (magneto-hydrodynamic) flow and
heat transfer of a non-Newtonian second grade viscoelastic fluid
over an oscillatory stretching sheet. The flow is induced due to an
infinite elastic sheet which is stretched oscillatory (back and forth) in
its own plane. Effect of viscous dissipation and joule heating are
taken into account. The non-linear differential equations governing
the problem are transformed into system of non-dimensional
differential equations using similarity transformations. A newly
developed meshfree numerical technique Element free Galerkin
method (EFGM) is employed to solve the coupled non linear
differential equations. The results illustrating the effect of various
parameters like viscoelastic parameter, Hartman number, relative
frequency amplitude of the oscillatory sheet to the stretching rate and
Eckert number on velocity and temperature field are reported in
terms of graphs and tables. The present model finds its application in
polymer extrusion, drawing of plastic films and wires, glass, fiber
and paper production etc.
Abstract: Steroidal hormones with the efficient changes on the epiphyseal growth plate may influence tissue structure properties. Presents paper to investigate the effects of gonadectomy in the pattern distribution of the epiphyseal structure. Fifteen adult female New Zealand white rabbits were separated into three groups. One group was intact and others groups were selected for surgical operation. From these two groups, one group carried out steroidal administration. The results obtained showed that there is no statistically difference in the mean diameter of the growth plate cells between all three groups. The maximum value of the cartilage cells were allocated to the gonadectomized group and the minimum number were observed in Hormonal induced group significantly. Growth plate height was significantly greater in gonadectomized group than in two other groups.
Abstract: The possibility of producing drinking water from
brackish ground water using Vacuum membrane distillation (VMD)
process was studied. It is a rising technology for seawater or brine
desalination process. The process simply consists of a flat sheet
hydrophobic micro porous PTFE membrane and diaphragm vacuum
pump without a condenser for the water recovery or trap. In this
work, VMD performance was investigated for aqueous NaCl solution
and natural ground water. The influence of operational parameters
such as feed flow rate (30 to 55 l/h), feed temperature (313 to 333 K),
feed salt concentration (5000 to 7000 mg/l) and permeate pressure
(1.5 to 6 kPa) on the membrane distillation (MD) permeation flux
have been investigated. The maximum flux reached to 28.34 kg/m2 h
at feed temperature, 333 K; vacuum pressure, 1.5 kPa; feed flow rate,
55 l/h and feed salt concentration, 7000 mg/l. The negligible effects
in the reduction of permeate flux found over 150 h experimental run
for salt water. But for the natural ground water application over 75 h,
scale deposits observed on the membrane surface and 29% reduction
in the permeate flux over 75 h. This reduction can be eliminated by
acidification of feed water. Hence, promote the research attention in
apply of VMD for the ground water purification over today-s
conventional RO operation.
Abstract: Optimal cultural site selection is one of the ways that
can lead to the promotion of citizenship culture in addition to
ensuring the health and leisure of city residents. This study examines
the social and cultural needs of the community and optimal cultural
site allocation and after identifying the problems and shortcomings,
provides a suitable model for finding the best location for these
centers where there is the greatest impact on the promotion of
citizenship culture. On the other hand, non-scientific methods cause
irreversible impacts to the urban environment and citizens. But
modern efficient methods can reduce these impacts. One of these
methods is using geographical information systems (GIS). In this
study, Analytical Hierarchy Process (AHP) method was used to
locate the optimal cultural site. In AHP, three principles
(decomposition), (comparative analysis), and (combining
preferences) are used. The objectives of this research include
providing optimal contexts for passing time and performing cultural
activities by Shiraz residents and also proposing construction of some
cultural sites in different areas of the city. The results of this study
show the correct positioning of cultural sites based on social needs of
citizens. Thus, considering the population parameters and radii
access, GIS and AHP model for locating cultural centers can meet
social needs of citizens.
Abstract: Eigenvector methods are gaining increasing acceptance in the area of spectrum estimation. This paper presents a successful attempt at testing and evaluating the performance of two of the most popular types of subspace techniques in determining the parameters of multiexponential signals with real decay constants buried in noise. In particular, MUSIC (Multiple Signal Classification) and minimum-norm techniques are examined. It is shown that these methods perform almost equally well on multiexponential signals with MUSIC displaying better defined peaks.
Abstract: A novel calibration approach that aims to reduce
ASM2d parameter subsets and decrease the model complexity is
presented. This approach does not require high computational
demand and reduces the number of modeling parameters required to
achieve the ASMs calibration by employing a sensitivity and iteration
methodology. Parameter sensitivity is a crucial factor and the
iteration methodology enables refinement of the simulation parameter
values. When completing the iteration process, parameters values are
determined in descending order of their sensitivities. The number of
iterations required is equal to the number of model parameters of the
parameter significance ranking. This approach was used for the
ASM2d model to the evaluated EBPR phosphorus removal and it was
successful. Results of the simulation provide calibration parameters.
These included YPAO, YPO4, YPHA, qPHA, qPP, μPAO, bPAO, bPP, bPHA,
KPS, YA, μAUT, bAUT, KO2 AUT, and KNH4 AUT. Those parameters were
corresponding to the experimental data available.
Abstract: As it is known, buoyancy and drag forces rule bubble's rise velocity in a liquid column. These forces are strongly dependent on fluid properties, gravity as well as equivalent's diameter. This study reports a set of bubble rising velocity experiments in a liquid column using water or glycerol. Several records of terminal velocity were obtained. The results show that bubble's rise terminal velocity is strongly dependent on dynamic viscosity effect. The data set allowed to have some terminal velocities data interval of 8.0 ? 32.9 cm/s with Reynolds number interval 1.3 -7490. The bubble's movement was recorded with a video camera. The main goal is to present an original set data and results that will be discussed based on two-phase flow's theory. It will also discussed, the prediction of terminal velocity of a single bubble in liquid, as well as the range of its applicability. In conclusion, this study presents general expressions for the determination of the terminal velocity of isolated gas bubbles of a Reynolds number range, when the fluid proprieties are known.
Abstract: This paper presents a numerical study on surface heat
transfer characteristics of laminar air flows in parallel-plate dimpled
channels. The two-dimensional numerical model is provided by
commercial code FLUENT and the results are obtained for channels
with symmetrically opposing hemi-cylindrical cavities onto both
walls for Reynolds number ranging from 1000 to 2500. The influence
of variations in relative depth of dimples (the ratio of cavity depth to
the cavity curvature diameter), the number of them and the thermophysical
properties of channel walls on heat transfer enhancement is
studied. The results are evident for existence of an optimum value for
the relative depth of dimples in which the largest wall heat flux and
average Nusselt number can be achieved. In addition, the results of
conjugation simulation indicate that the overall influence of the ratio
of wall thermal conductivity to the one of the fluid on heat transfer
rate is not much significant and can be ignored.
Abstract: In this paper we consider the problem of distributed adaptive estimation in wireless sensor networks for two different observation noise conditions. In the first case, we assume that there are some sensors with high observation noise variance (noisy sensors) in the network. In the second case, different variance for observation noise is assumed among the sensors which is more close to real scenario. In both cases, an initial estimate of each sensor-s observation noise is obtained. For the first case, we show that when there are such sensors in the network, the performance of conventional distributed adaptive estimation algorithms such as incremental distributed least mean square (IDLMS) algorithm drastically decreases. In addition, detecting and ignoring these sensors leads to a better performance in a sense of estimation. In the next step, we propose a simple algorithm to detect theses noisy sensors and modify the IDLMS algorithm to deal with noisy sensors. For the second case, we propose a new algorithm in which the step-size parameter is adjusted for each sensor according to its observation noise variance. As the simulation results show, the proposed methods outperforms the IDLMS algorithm in the same condition.
Abstract: This article presents a numerical study of the doublediffusive
mixed convection in a vertical channel filled with porous
medium by using non-equilibrium model. The flow is assumed
fully developed, uni-directional and steady state. The controlling
parameters are thermal Rayleigh number (RaT ), Darcy number (Da),
Forchheimer number (F), buoyancy ratio (N), inter phase heat transfer
coefficient (H), and porosity scaled thermal conductivity ratio
(γ). The Brinkman-extended non-Darcy model is considered. The
governing equations are solved by spectral collocation method. The
main emphasize is given on flow profiles as well as heat and solute
transfer rates, when two diffusive components in terms of buoyancy
ratio are in favor (against) of each other and solid matrix and fluid
are thermally non-equilibrium. The results show that, for aiding flow
(RaT = 1000), the heat transfer rate of fluid (Nuf ) increases upto a
certain value of H, beyond that decreases smoothly and converges
to a constant, whereas in case of opposing flow (RaT = -1000),
the result is same for N = 0 and 1. The variation of Nuf in (N,
Nuf )-plane shows sinusoidal pattern for RaT = -1000. For both cases
(aiding and opposing) the flow destabilize on increasing N by inviting
point of inflection or flow separation on the velocity profile. Overall,
the buoyancy force have significant impact on the non-Darcy mixed
convection under LTNE conditions.
Abstract: A multiple-option analytical model for the evaluation of the energy performance and distribution of aerodynamic forces acting on a vertical-axis Darrieus wind turbine depending on both rotor architecture and operating conditions is presented. For this purpose, a numerical algorithm, capable of generating the desired rotor conformation depending on design geometric parameters, is coupled to a Single/Double-Disk Multiple-Streamtube Blade Element – Momentum code. Both single and double-disk configurations are analyzed and model predictions are compared to literature experimental data in order to test the capability of the code for predicting rotor performance. Effective airfoil characteristics based on local blade Reynolds number are obtained through interpolation of literature low-Reynolds airfoil databases. Some corrections are introduced inside the original model with the aim of simulating also the effects of blade dynamic stall, rotor streamtube expansion and blade finite aspect ratio, for which a new empirical relationship to better fit the experimental data is proposed. In order to predict also open field rotor operation, a freestream wind shear profile is implemented, reproducing the effect of atmospheric boundary layer.
Abstract: Cobalt was acid nitric leached from a mixed cobaltcopper
oxide with variable acid concentration. Resulting
experimental data were used to analyze effects of increase in acid
concentration, based on a shrinking core model of the process. The
mathematical simulation demonstrated that the time rate of the
dissolution mechanism is an increasing function of acid
concentration. It was also shown that the magnitude of the acid
concentration effect is time dependent and the increase in acid
concentration is more effective at earlier stage of the dissolution than
at later stage. The remaining process parameters are comprehensively
affected by acid concentration and their interaction is synergetic.
Abstract: Data rate, tolerable bit error rate or frame error rate
and range & coverage are the key performance requirement of a
communication link. In this paper performance of MFSK link is
analyzed in terms of bit error rate, number of errors and total number
of data processed. In the communication link model proposed, which
is implemented using MATLAB block set, an improvement in BER
is observed. Different parameters which effects and enables to keep
BER low in M-ary communication system are also identified.
Abstract: In this paper multi-objective genetic algorithms are
employed for Pareto approach optimization of ideal Turboshaft
engines. In the multi-objective optimization a number of conflicting
objective functions are to be optimized simultaneously. The
important objective functions that have been considered for
optimization are specific thrust (F/m& 0), specific fuel consumption
( P S ), output shaft power 0 (& /&) shaft W m and overall efficiency( ) O
η .
These objectives are usually conflicting with each other. The design
variables consist of thermodynamic parameters (compressor pressure
ratio, turbine temperature ratio and Mach number).
At the first stage single objective optimization has been
investigated and the method of NSGA-II has been used for multiobjective
optimization. Optimization procedures are performed for
two and four objective functions and the results are compared for
ideal Turboshaft engine. In order to investigate the optimal
thermodynamic behavior of two objectives, different set, each
including two objectives of output parameters, are considered
individually. For each set Pareto front are depicted. The sets of
selected decision variables based on this Pareto front, will cause the
best possible combination of corresponding objective functions.
There is no superiority for the points on the Pareto front figure,
but they are superior to any other point. In the case of four objective
optimization the results are given in tables.