Abstract: In this paper, the effects of radiation, chemical
reaction and double dispersion on mixed convection heat and mass
transfer along a semi vertical plate are considered. The plate is
embedded in a Newtonian fluid saturated non - Darcy (Forchheimer
flow model) porous medium. The Forchheimer extension and first
order chemical reaction are considered in the flow equations. The
governing sets of partial differential equations are nondimensionalized
and reduced to a set of ordinary differential
equations which are then solved numerically by Fourth order Runge–
Kutta method. Numerical results for the detail of the velocity,
temperature, and concentration profiles as well as heat transfer rates
(Nusselt number) and mass transfer rates (Sherwood number) against
various parameters are presented in graphs. The obtained results are
checked against previously published work for special cases of the
problem and are found to be in good agreement.
Abstract: One of the main problems of suspended cable structures is initial shape change under the action of non uniform load. The problem can be solved by increasing of weight of construction or by using of prestressing. But this methods cause increasing of materials consumption of suspended cable structure. The cable truss usage is another way how the problem of shape change under the action of non uniform load can be fixed. The cable trusses with the vertical and inclined suspensions, cross web and single cable were analyzed as the main load-bearing structures of suspension bridge. It was shown, that usage of cable truss allows to reduce the vertical displacements up to 32% in comparison with the single cable in case of non uniformly distributed load. In case of uniformly distributed load single cable is preferable.
Abstract: The substrate heater designed for this investigation is a front side substrate heating system. It consists of 10 conventional tungsten halogen lamps and an aluminum reflector, total input electrical power of 5 kW. The substrate is heated by means of a radiation from conventional tungsten halogen lamps directed to the substrate through a glass window. This design allows easy replacement of the lamps and maintenance of the system. Within 2 to 6 minutes the substrate temperature reaches 500 to 830 C by varying the vertical distance between the glass window and the substrate holder. Moreover, the substrate temperature can be easily controlled by controlling the input power to the system. This design gives excellent opportunity to deposit many deferent films at deferent temperatures in the same deposition time. This substrate heater was successfully used for Chemical Vapor Deposition (CVD) of many thin films, such as Silicon, iron, etc.
Abstract: In mechanical and environmental engineering, mixed
convection is a frequently encountered thermal fluid phenomenon
which exists in atmospheric environment, urban canopy flows, ocean
currents, gas turbines, heat exchangers, and computer chip cooling
systems etc... . This paper deals with a numerical investigation of
mixed convection in a vertical heated channel. This flow results from
the mixing of the up-going fluid along walls of the channel with the
one issued from a flat nozzle located in its entry section. The fluiddynamic
and heat-transfer characteristics of vented vertical channels
are investigated for constant heat-flux boundary conditions, a
Rayleigh number equal to 2.57 1010, for two jet Reynolds number
Re=3 103 and 2104 and the aspect ratio in the 8-20 range. The system
of governing equations is solved with a finite volumes method and an
implicit scheme. The obtained results show that the turbulence and
the jet-wall interaction activate the heat transfer, as does the drive of
ambient air by the jet. For low Reynolds number Re=3 103, the
increase of the aspect Ratio enhances the heat transfer of about 3%,
however; for Re=2 104, the heat transfer enhancement is of about
12%. The numerical velocity, pressure and temperature fields are
post-processed to compute the quantities of engineering interest such
as the induced mass flow rate, and average Nusselt number, in terms
of Rayleigh, Reynolds numbers and dimensionless geometric
parameters are presented.
Abstract: In this experimental investigation shake table tests
were conducted on two reduced models that represent normal single
room building constructed by Compressed Stabilized Earth Block
(CSEB) from locally available soil. One model was constructed with
earthquake resisting features (EQRF) having sill band, lintel band and
vertical bands to control the building vibration and another one was
without Earthquake Resisting Features. To examine the seismic
capacity of the models particularly when it is subjected to long-period
ground motion by large amplitude by many cycles of repeated
loading, the test specimen was shaken repeatedly until the failure.
The test results from Hi-end Data Acquisition system show that
model with EQRF behave better than without EQRF. This modified
masonry model with new material combined with new bands is used
to improve the behavior of masonry building.
Abstract: Hidden Markov Model (HMM) is a stochastic method
which has been used in various signal processing and character
recognition. This study proposes to use HMM to recognize Javanese
characters from a number of different handwritings, whereby HMM
is used to optimize the number of state and feature extraction. An
85.7 % accuracy is obtained as the best result in 16-stated vertical
model using pure HMM. This initial result is satisfactory for
prompting further research.
Abstract: In this work a dynamic model of a new quadrotor aerial
vehicle that is equipped with a tilt-wing mechanism is presented.
The vehicle has the capabilities of vertical take-off/landing (VTOL)
like a helicopter and flying horizontal like an airplane. Dynamic
model of the vehicle is derived both for vertical and horizontal flight
modes using Newton-Euler formulation. An LQR controller for the
vertical flight mode has also been developed and its performance
has been tested with several simulations.
Abstract: In this paper, two centrifugal model tests (case 1: raft
foundation, case 2: 2x2 piled raft foundation) were conducted in
order to evaluate the effect of ground subsidence on load sharing
among piles and raft and settlement of raft and piled raft
foundations. For each case, two conditions consisting of undrained
(without groundwater pumping) and drained (with groundwater
pumping) conditions were considered. Vertical loads were applied
to the models after the foundations were completely consolidated by
selfweight at 50g. The results show that load sharing by the piles in
piled raft foundation (piled load share) for drained condition
decreases faster than that for undrained condition. Settlement of
both raft and piled raft foundations for drained condition increases
more quickly than that for undrained condition. In addition, the
settlement of raft foundation increases more largely than the
settlement of piled raft foundation for drained condition.
Abstract: The machining performance is determined by the
frequency characteristics of the machine-tool structure and the
dynamics of the cutting process. Therefore, the prediction of dynamic
vibration behavior of spindle tool system is of great importance for the
design of a machine tool capable of high-precision and high-speed
machining. The aim of this study is to develop a finite element model
to predict the dynamic characteristics of milling machine tool and
hence evaluate the influence of the preload of the spindle bearings. To
this purpose, a three dimensional spindle bearing model of a high
speed engraving spindle tool was created. In this model, the rolling
interfaces with contact stiffness defined by Harris model were used to
simulate the spindle bearing components. Then a full finite element
model of a vertical milling machine was established by coupling the
spindle tool unit with the machine frame structure. Using this model,
the vibration mode that had a dominant influence on the dynamic
stiffness was determined. The results of the finite element simulations
reveal that spindle bearing with different preloads greatly affect the
dynamic behavior of the spindle tool unit and hence the dynamic
responses of the vertical column milling system. These results were
validated by performing vibration on the individual spindle tool unit
and the milling machine prototype, respectively. We conclude that
preload of the spindle bearings is an important component affecting
the dynamic characteristics and machining performance of the entire
vertical column structure of the milling machine.
Abstract: The boundary layer flow and heat transfer on a
stretched surface moving with prescribed skin friction is studied for
permeable surface. The surface temperature is assumed to vary
inversely with the vertical direction x for n = -1. The skin friction at
the surface scales as (x-1/2) at m = 0. The constants m and n are the
indices of the power law velocity and temperature exponent
respectively. Similarity solutions are obtained for the boundary layer
equations subject to power law temperature and velocity variation.
The effect of various governing parameters, such as the buoyancy
parameter λ and the suction/injection parameter fw for air (Pr = 0.72)
are studied. The choice of n and m ensures that the used similarity
solutions are x independent. The results show that, assisting flow (λ >
0) enhancing the heat transfer coefficient along the surface for any
constant value of fw. Furthermore, injection increases the heat
transfer coefficient but suction reduces it at constant λ.
Abstract: In this paper, the feasibility study of using a hybrid
system of ground heat exchangers (GHE) and direct evaporative
cooling system in arid weather condition has been performed. The
model is applied for Yazd and Kerman, two cities with arid weather
condition in Iran. The system composed of three sections: Ground-
Coupled-Circuit (GCC), Direct Evaporative Cooler (DEC) and
Cooling Coil Unite (CCU). The GCC provides the necessary precooling
for DEC. The GCC includes four vertical GHE which are
designed in series configuration. Simulation results show that
hybridization of GCC and DEC could provide comfort condition
whereas DEC alone did not. Based on the results the cooling
effectiveness of a hybrid system is more than unity. Thus, this novel
hybrid system could decrease the air temperature below the ambient
wet-bulb temperature. This environmentally clean and energy
efficient system can be considered as an alternative to the mechanical
vapor compression systems.
Abstract: The main purpose of this paper is to research on the
methodologies of BYD to implement the opportune innovation. BYD
is a Chinese company which has the IT component manufacture, the
rechargeable battery and the automobile businesses. The paper deals
with the innovation methodology as the same as the IPR management
BYD implements in order to obtain the rapid growth of technology
development with the reasonable cost of money and time.
Abstract: Investigation of sandy clay behavior is important since
urban development demands mean that sandy clay areas are
increasingly encountered, especially for transportation
infrastructures. This paper presents the results of the finite element
analysis of the direct shear test (under three vertical loading 44, 96
and 192 kPa) and discusses the effects of different parameters such as
cohesion, friction angle and Young's modulus on the shear strength of
sandy clay. The numerical model was calibrated against the
experimental results of large-scale direct shear tests. The results have
shown that the shear strength was increased with increase in friction
angle and cohesion. However, the shear strength was not influenced
by raising the friction angle at normal stress of 44 kPa. Also, the
effect of different young's modulus factors on stress-strain curve was
investigated.
Abstract: Steady state experiments have been conducted for
natural and mixed convection heat transfer, from five different sized
protruding discrete heat sources, placed at the bottom position on a
PCB and mounted on a vertical channel. The characteristic length (
Lh ) of heat sources vary from 0.005 to 0.011 m. The study has been
done for different range of Reynolds number and modified Grashof
number. From the experiment, the surface temperature distribution
and the Nusselt number of discrete heat sources have been obtained
and the effects of Reynold number and Richardson number on them
have been discussed. The objective is to find the rate of heat
dissipation from heat sources, by placing them at the bottom position
on a PCB and to compare both modes of cooling of heat sources.
Abstract: Seasonal variability of nutrients concentration in the Baltic Sea using the 3D ecosystem numerical model 3D-CEMBS has been investigated. Additionally this study shows horizontal and vertical distribution of nutrients in the Baltic Sea. Model domain is an extended Baltic Sea area divided into 600x640 horizontal grid cells. Aside from standard hydrodynamic parameters 3D-CEMBS produces modeled ecological variables such as: three types of phytoplankton, two detrital classes, dissolved oxygen and the nutrients (nitrate, ammonium, phosphate and silicate). The presented model allows prediction of parameters that describe distribution of nutrients concentration and phytoplankton biomass. 3D-CEMBS can be used to study the effect of different hydrodynamic and biogeochemical processes on distributions of these variables in a larger scale.
Abstract: Unsteady natural convection and heat transfer in a square cavity partially filled with porous media using a thermal
non-equilibrium model is studied in this paper. The left vertical wall is
maintained at a constant hot temperature Th and the right vertical wall
is maintained at a constant cold temperature Tc, while the horizontal
walls are adiabatic. The governing equations are obtained by applying
the Darcy model and Boussinesq approximation. COMSOL’s finite
element method is used to solve the non-dimensional governing
equations together with specified boundary conditions. The governing
parameters of this study are the Rayleigh number (Ra = 10^5, and Ra = 10^6 ), Darcy namber (Da = 10^−2, and Da = 10^−3),
the modified thermal conductivity ratio (10^−1 ≤ γ ≤ 10^4), the inter-phase heat transfer coefficien (10^−1 ≤ H ≤ 10^3) and the
time dependent (0.001 ≤ τ ≤ 0.2). The results presented for
values of the governing parameters in terms of streamlines in both
fluid/porous-layer, isotherms of fluid in fluid/porous-layer, isotherms
of solid in porous layer, and average Nusselt number.
Abstract: A facile vapour deposition method of synthesis of vertically aligned ZnO nanowires on carbon seed layer was developed. The received samples were investigated on electronic microscope JSM-6490 LA JEOL and x-ray diffractometer X, pert MPD PRO. The photoluminescence spectra (PL) of obtained ZnO samples at a room temperature were studied using He-Cd laser (325 nm line) as excitation source.
Abstract: The purpose of this study was to measure the maximal
isometric strength and to investigate the effects of different handleheights
and elbow angles with respect to Mid. sagittal plane on the
pushing and pulling strength in vertical direction. Eight male subjects
performed a series of static strength measurement for each subject.
The highest isometric strength was found in pulling at shoulder
height (S.H.) (Mean = 60.29 lb., SD = 16.78 lb.) and the lowest
isometric strength was found also in pulling at elbow height (E.H.)
(Mean = 33.06 lb., SD = 6.56 lb.). Although the isometric strengths
were higher at S.H than at E.H. for both activities, the maximal
isometric strengths were compared statistically. ANOVA was
performed. The results of the experiment revealed that there was a
significant different between handle heights. However, there were no
significant different between angles and activities, also no correlation
between grip strength and activities.
Abstract: Understanding the number of people and the flow of
the persons is useful for efficient promotion of the institution
managements and company-s sales improvements. This paper
introduces an automated method for counting passerby using virtualvertical
measurement lines. The process of recognizing a passerby is
carried out using an image sequence obtained from the USB camera.
Space-time image is representing the human regions which are
treated using the segmentation process. To handle the problem of
mismatching, different color space are used to perform the template
matching which chose automatically the best matching to determine
passerby direction and speed. A relation between passerby speed and
the human-pixel area is used to distinguish one or two passersby. In
the experiment, the camera is fixed at the entrance door of the hall in
a side viewing position. Finally, experimental results verify the
effectiveness of the presented method by correctly detecting and
successfully counting them in order to direction with accuracy of
97%.
Abstract: Radio wave propagation on the road surface is a major
problem on wireless sensor network for traffic monitoring. In this
paper, we compare receiving signal strength on two scenarios 1) an
empty road and 2) a road with a vehicle. We investigate the effect of
antenna polarization and antenna height to the receiving signal
strength. The transmitting antenna is installed on the road surface.
The receiving signal is measured 360 degrees around the transmitting
antenna with the radius of 2.5 meters. Measurement results show the
receiving signal fluctuation around the transmitting antenna in both
scenarios. Receiving signal with vertical polarization antenna results
in higher signal strength than horizontal polarization antenna. The
optimum antenna elevation is 1 meter for both horizon and vertical
polarizations with the vehicle on the road. In the empty road, the
receiving signal level is unvarying with the elevation when the
elevation is greater than 1.5 meters.