Abstract: Thin-walled elements with a matrix set on a base of
high-valuable Portland cement with dispersed reinforcement from
alkali-resistant glass fibres are used in a range of applications as
claddings of buildings and infrastructure constructions as well as
various architectural elements of residential buildings.
Even though their elementary thickness and therefore total weight
is quite low, architects and building companies demand on even
further decreasing of the bulk density of these fibre-cement elements
for the reason of loading elimination of connected superstructures
and easier assembling in demand conditions.
By the means of various kinds of light-weight aggregates it is
possible to achieve light-weighing of these composite elements.
From the range of possible fillers with different material properties
granulated expanded glass worked the best.
By the means of laboratory testing an effect of two fillers based on
expanded glass on the fibre reinforced cement composite was
verified.
Practical applicability was tested in the production of commonly
manufactured glass fibre reinforced concrete elements, such as
channels for electrical cable deposition, products for urban equipment
and especially various cladding elements.
Even though these are not structural elements, it is necessary to
evaluate also strength characteristics and resistance to environment
for their durability in certain applications.
Abstract: Hurling a successful Construction and Demolition
Waste (C&DW) recycling operation around the globe is a challenge
today, predominantly because secondary materials markets are yet to
be integrated. Reducing, Reusing and recycling of (C&DW) have
been employed over the years, and various techniques have been
investigated. However, the economic and environmental viability of
its application seems limited. This paper discusses the costs and
benefits in using secondary materials and focus on investigating reuse
and recycling process for five major types of construction materials:
concrete, metal, wood, cardboard/paper and plasterboard. Data
obtained from demolition specialists and contractors are considered
and evaluated. The research paper found that construction material
recovery process fully incorporate a 3R’s principle contributing to
saving energy and natural resources. This scrutiny leads to the
empathy of grand challenges in construction material recovery
process. Recommendations to deepen material recovery process are
also discussed.
Abstract: The composite pavement system considered in this
paper is composed of a functional surface layer, a fiber reinforced
asphalt middle layer and a fiber reinforced lean concrete base layer.
The mix design of the fiber reinforced lean concrete corresponds to the
mix composition of conventional lean concrete but reinforced by
fibers. The quasi-absence of research on the durability or long-term
performances (fatigue, creep, etc.) of such mix design stresses the
necessity to evaluate experimentally the long-term characteristics of
this layer composition. This study tests the creep characteristics as one
of the long-term characteristics of the fiber reinforced lean concrete
layer for composite pavement using a new creep device. The test
results reveal that the lean concrete mixed with fiber reinforcement
and fly ash develops smaller creep than the conventional lean
concrete. The results of the application of the CEB-FIP prediction
equation indicate that a modified creep prediction equation should be
developed to fit with the new mix design of the layer.
Abstract: In this paper, the author studied the possibilities of
using Rice Husk Ash (RHA) available in India; to produce concrete.
Experiments conducted with RHA obtained from West Bengal, India;
to replace cement partially to produce concrete of grade M10, M15,
M20, M25 and M30. The concrete produced in the laboratory by
replacing cement by 5%, 10%, 15%, 20%, 25% and 30% RHA.
Compressive strength tests carried out to determine the strength of
concrete. Cost analysis and comparison done to show the cost
effectiveness of RHA Concrete. Traditional uses of Rice Husk in
India pointed out and the advantages of using RHA in making
concrete highlighted. Suggestion provided regarding prospective
application of RHA concrete in India; which in turn will definitely
reduce the cost of concrete and environmental friendly due to
utilization of waste and replacement of Cement.
Abstract: Concrete is found to undergo degradation when
subjected to elevated temperatures and loose substantial amount of its
strength. The loss of strength in concrete is mainly attributed to
decomposition of C-S-H and release of physically and chemically
bound water, which begins when the exposure temperature exceeds
100°C. When such a concrete comes in contact with moisture, the
cement paste is found rehydrate and considerable amount of strength
lost is found to recover. This paper presents results of an
experimental program carried out to investigate the effect of recuring
on strength gain of OPC concrete specimens subjected to elevated
temperatures from 200°C to 800°C, which were subjected to
retention time of two hours and four hours at the designated
temperature. Strength recoveries for concrete subjected to 7
designated elevated temperatures are compared. It is found that the
efficacy of recuring as a measure of strength recovery reduces with
increase in exposure temperature.
Abstract: The decision-making process is theoretically clearly
defined. Generally, it includes the problem identification and
analysis, data gathering, goals and criteria setting, alternatives
development and optimal alternative choice and its implementation.
In practice however, various modifications of the theoretical
decision-making process can occur. The managers can consider some
of the phases to be too complicated or unfeasible and thus they do not
carry them out and conversely some of the steps can be
overestimated.
The aim of the paper is to reveal and characterize the perception of
the individual phases of decision-making process by the managers.
The research is concerned with managers in the military environment
– commanders. Quantitative survey is focused cross-sectionally in the
individual levels of management of the Ministry of Defence of the
Czech Republic. On the total number of 135 respondents the analysis
focuses on which of the decision-making process phases are
problematic or not carried out in practice and which are again
perceived to be the easiest. Then it is examined the reasons of the
findings.
Abstract: Cement concrete is a complex mixture of different
materials. Behaviour of concrete depends on its mix proportions and
constituents when it is subjected to elevated temperatures. Principal
effects due to elevated temperatures are loss in compressive strength,
loss in weight or mass, change in colour and spall of concrete. The
experimental results of normal concrete and high strength concrete
subjected elevated temperatures at 200°C, 400°C, 600°C, and 800°C
and different cooling regimes viz. air cooling, water quenching on
different grade of concrete are reported in this paper.
Abstract: This work reports the potential of using Palm Kernel
(PK) ash and shell as a partial substitute for Portland Cement (PC)
and coarse aggregate in the development of mortar and concrete. PK
ash and shell are agro-waste materials from palm oil mills, the
disposal of PK ash and shell is an environmental problem of concern.
The PK ash has pozzolanic properties that enables it as a partial
replacement for cement and also plays an important role in the
strength and durability of concrete, its use in concrete will alleviate
the increasing challenges of scarcity and high cost of cement. In order
to investigate the PC replacement potential of PK ash, three types of
PK ash were produced at varying temperature (350-750C) and they
were used to replace up to 50% PC. The PK shell was used to replace
up to 100% coarse aggregate in order to study its aggregate
replacement potential. The testing programme included material
characterisation, the determination of compressive strength, tensile
splitting strength and chemical durability in aggressive sulfatebearing
exposure conditions. The 90 day compressive results showed
a significant strength gain (up to 26.2 N/mm2). The Portland cement
and conventional coarse aggregate has significantly higher influence
in the strength gain compared to the equivalent PK ash and PK shell.
The chemical durability results demonstrated that after a prolonged
period of exposure, significant strength losses in all the concretes
were observed. This phenomenon is explained, due to lower change
in concrete morphology and inhibition of reaction species and the
final disruption of the aggregate cement paste matrix.
Abstract: Environmental impact assessment techniques have
been developed as a result of the worldwide efforts to reduce the
environmental impact of global warming. By using the quantification
method in the construction industry, it is now possible to manage the
greenhouse gas is to systematically evaluate the impact on the
environment over the entire construction process. In particular, the
proportion of greenhouse gas emissions at the production stage of
construction material occupied is high, and efforts are needed in
particular in the construction field.
In this research, intended for concrete products for the construction
materials, by using the LCA method, we compared the results of
environmental impact assessment and carbon emissions of developing
products that have been applied low-carbon technologies compared to
existing products. As a results, by introducing a raw material of
industrial waste, showed carbon reduction. Through a comparison of
the carbon emission reduction effect of low carbon technologies, it is
intended to provide academic data for the evaluation of greenhouse
gases in the construction sector and the development of low carbon
technologies of the future.
Abstract: This study examines analytically the effect of tsunami loads on reinforced concrete (RC) frame buildings. The impact of tsunami wave loads and waterborne objects are analyzed using a typical substandard full-scale two-story RC frame building tested as part of the EU-funded Ecoleader project. The building was subjected to shake table tests in bare condition, and subsequently strengthened using Carbon Fiber Reinforced Polymers (CFRP) composites and retested. Numerical models of the building in both bare and CFRP-strengthened conditions are calibrated in DRAIN-3DX software to match the test results. To investigate the response of wave loads and impact forces, the numerical models are subjected to nonlinear dynamic analyses using force time-history input records. The analytical results are compared in terms of displacements at the floors and at the “impact point” of a boat. The results show that the roof displacement of the CFRP-strengthened building reduced by 63% when compared to the bare building. The results also indicate that strengthening only the mid-height of the impact column using CFRP is more effective at reducing damage when compared to strengthening other parts of the column. Alternative solutions to mitigate damage due to tsunami loads are suggested.
Abstract: The aim of this paper is to perform experimental
modal analysis (EMA) of reinforced concrete (RC) square slabs.
EMA is the process of determining the modal parameters (Natural
Frequencies, damping factors, modal vectors) of a structure from a
set of frequency response functions FRFs (curve fitting). Although,
experimental modal analysis (or modal testing) has grown steadily in
popularity since the advent of the digital FFT spectrum analyzer in
the early 1970’s, studying all types of members and materials using
such method have not yet been well documented. Therefore, in this
work, experimental tests were conducted on RC square slab
specimens of dimensions 600mm x 600mmx 40mm. Experimental
analysis was based on freely supported boundary condition.
Moreover, impact testing as a fast and economical means of finding
the modes of vibration of a structure was used during the
experiments. In addition, Pico Scope 6 device and MATLAB
software were used to acquire data, analyze and plot Frequency
Response Function (FRF). The experimental natural frequencies
which were extracted from measurements exhibit good agreement
with analytical predictions. It is showed that EMA method can be
usefully employed to investigate the dynamic behavior of RC slabs.
Abstract: Geometric and mechanical properties all influence the
resistance of RC structures and may, in certain combination of
property values, increase the risk of a brittle failure of the whole
system.
This paper presents a statistical and probabilistic investigation on
the resistance of RC beams designed according to Eurocodes 2 and 8,
and subjected to multiple failure modes, under both the natural
variation of material properties and the uncertainty associated with
cross-section and transverse reinforcement geometry. A full
probabilistic model based on JCSS Probabilistic Model Code is
derived. Different beams are studied through material nonlinear
analysis via Monte Carlo simulations. The resistance model is
consistent with Eurocode 2. Both a multivariate statistical evaluation
and the data clustering analysis of outcomes are then performed.
Results show that the ultimate load behaviour of RC beams
subjected to flexural and shear failure modes seems to be mainly
influenced by the combination of the mechanical properties of both
longitudinal reinforcement and stirrups, and the tensile strength of
concrete, of which the latter appears to affect the overall response of
the system in a nonlinear way. The model uncertainty of the
resistance model used in the analysis plays undoubtedly an important
role in interpreting results.
Abstract: Since columns are the most important elements of the
structures, failure of one column in a critical location can cause a
progressive collapse. In this respect, the repair and strengthening of
columns is a very important subject to reduce the building failure and
to keep the columns capacity. Twenty columns with different
parameters is tested and analysis. Eleven typical confined reinforced
concrete (RC) columns with different types of techniques are
assessment. And also, four confined concrete columns with plastic
tube (PVC) are tested with and with four paralleling tested of
unconfined plain concrete. The techniques of confined RC columns
are mortar strengthening, Steel rings strengthening, FRP
strengthening. Moreover, the technique of confined plain concrete
(PC) column is used PVC tubes. The columns are tested under
uniaxial compressive loads studied the effect of confinement on the
structural behavior of circular RC columns. Test results for each
column are presented in the form of crack patterns, stress-strain
curves. Test results show that confining of the RC columns using
different techniques of strengthening results significant improvement
of the general behavior of the columns and can used in construction.
And also, tested confined PC columns with PVC tubes results shown
that the confined PC with PVC tubes can be used in economical
building. The theoretical model for predicted column capacity is
founded with experimental factor depends on the confined techniques
used and the strain reduction.
Abstract: This study carried out comparative seismic
performance of reinforced concrete frames infilled by masonry walls
with different heights. Partial and fully infilled reinforced concrete
frames were modeled for the research objectives and the analysis
model for a bare reinforced concrete frame was also established for
comparison. Non–linear static analyses for the studied frames were
performed to investigate their structural behavior under extreme
seismic loads and to find out their collapse mechanism. It was
observed from analysis results that the strengths of the partial infilled
reinforced concrete frames are increased and their ductilities are
reduced, as infilled masonry walls are higher. Especially, reinforced
concrete frames with higher partial infilled masonry walls would
experience shear failures. Non–linear dynamic analyses using 10
earthquake records show that the bare and fully infilled reinforced
concrete frame present stable collapse mechanism while the reinforced
concrete frames with partially infilled masonry walls collapse in more
brittle manner due to short-column effects.
Abstract: In this paper, the effect of grades 32.4 and 42.5
Portland-limestone cements generally used for concrete production in
Nigeria on concrete compressive strength is investigated.
Investigation revealed that the compressive strength of concrete
produced with Portland-limestone cement grade 42.5 is generally
higher than that produced with cement grade 32.5. The percentage
difference between the compressive strengths of the concrete cubes
produced with Portland-limestone cement grades 42.5 and 32.5 is
inversely proportional to the richness of the concrete with the highest
and the least percentage difference associated with the 1:2:4 and
1:1:2 mix ratios respectively. It is recommended that cement grade
42.5 be preferred for construction in Nigeria as this will lead to the
construction of stronger concrete structures, which will reduce the
incidence of failure of building and other concrete structures at no
additional cost since the cost of both cement grades are the same.
Abstract: In this paper, a nonlinear Finite Element Analysis
(FEA) was carried out using ANSYS software to build a model able
of predicting the behavior of Reinforced Concrete (RC) beams with
unbonded reinforcement. The FEA model was compared to existing
experimental data by other researchers. The existing experimental
data consisted of 16 beams that varied from structurally sound beams
to beams with unbonded reinforcement with different unbonded
lengths and reinforcement ratios. The model was able to predict the
ultimate flexural strength, load-deflection curve, and crack pattern of
concrete beams with unbonded reinforcement. It was concluded that
when the when the unbonded length is less than 45% of the span,
there will be no decrease in the ultimate flexural strength due to the
loss of bond between the steel reinforcement and the surrounding
concrete regardless of the reinforcement ratio. Moreover, when the
reinforcement ratio is relatively low, there will be no decrease in
ultimate flexural strength regardless of the length of unbond.
Abstract: The main objective of this paper is study the influence
of carbon nano-tubes fibers and nano silica fibers on the
characteristic compressive strength and flexural strength on concrete
and cement mortar. Twelve tested specimens were tested with square
section its dimensions (4040 160) mm, divided into four groups.
The first and second group studied the effect of carbon nano-tubes
(CNTs) fibers with different percentage equal to 0.0, 0.11%, 0.22%,
and 0.33% by weight of cement and effect of nano-silica (nS) fibers
with different percentages equal to 0.0, 1.0%, 2.0%, and 3.0% by
weight of cement on the cement mortar. The third and fourth groups
studied the effect of CNTs fiber with different percentage equal to
0.0%, 0.11%, and 0.22% by weight of cement, and effect of nS fibers
with different percentages were equal to 0.0%, 1.0%, and 2.0% by
weight of cement on the concrete. The compressive strength and
flexural strength at 7, 28, and 90 days is determined. From analysis of
tested results concluded that the nano-fibers is more effective when
used with cement mortar more than used with concrete because of
increasing the surface area, decreasing the pore and the collection of
nano-fibers. And also by adding nano-fibers the improvement of
flexural strength of concrete and cement mortar is more than
improvement of compressive strength.
Abstract: Building loss estimation methodologies which have
been advanced considerably in recent decades are usually used to
estimate socio and economic impacts resulting from seismic structural
damage. In accordance with these methods, this paper presents the
evaluation of an annual loss probability of a reinforced concrete
moment resisting frame designed according to Korean Building Code.
The annual loss probability is defined by (1) a fragility curve obtained
from a capacity spectrum method which is similar to a method adopted
from HAZUS, and (2) a seismic hazard curve derived from annual
frequencies of exceedance per peak ground acceleration. Seismic
fragilities are computed to calculate the annual loss probability of a
certain structure using functions depending on structural capacity,
seismic demand, structural response and the probability of exceeding
damage state thresholds. This study carried out a nonlinear static
analysis to obtain the capacity of a RC moment resisting frame
selected as a prototype building. The analysis results show that the
probability of being extensive structural damage in the prototype
building is expected to 0.01% in a year.
Abstract: Company managers are always looking for more and
more opportunities to succeed in today's fiercely competitive market.
To maintain your place among the successful companies on the
market today or to come up with a revolutionary business idea is
much more difficult than before. Each new or improved method, tool,
or approach that can improve the functioning of business processes or
even of the entire system is worth checking and verification. The use
of simulation in the design of manufacturing systems and their
management in practice is one of the ways without increased risk,
which makes it possible to find the optimal parameters of
manufacturing processes and systems. The paper presents an example
of use of simulation for solution of the bottleneck problem in the
concrete company.
Abstract: At certain depths during large diameter displacement
pile driving, rebound well over 0.25 inches was experienced,
followed by a small permanent-set during each hammer blow. High
pile rebound (HPR) soils may stop the pile driving and results in a
limited pile capacity. In some cases, rebound leads to pile damage,
delaying the construction project, and the requiring foundations
redesign. HPR was evaluated at seven Florida sites, during driving of
square precast, prestressed concrete piles driven into saturated, fine
silty to clayey sands and sandy clays. Pile Driving Analyzer (PDA)
deflection versus time data recorded during installation, was used to
develop correlations between cone penetrometer (CPT) pore-water
pressures, pile displacements and rebound. At five sites where piles
experienced excessive HPR with minimal set, the pore pressure
yielded very high positive values of greater than 20 tsf. However, at
the site where the pile rebounded, followed by an acceptable
permanent-set, the measured pore pressure ranged between 5 and 20
tsf. The pore pressure exhibited values of less than 5 tsf at the site
where no rebound was noticed. In summary, direct correlations
between CPTu pore pressure and rebound were produced, allowing
identification of soils that produce HPR.