Abstract: This paper presents a design of dynamic feedback
control based on observer for a class of large scale Lipschitz nonlinear
systems. The use of Differential Mean Value Theorem (DMVT) is to
introduce a general condition on the nonlinear functions. To ensure
asymptotic stability, sufficient conditions are expressed in terms of
linear matrix inequalities (LMIs). High performances are shown
through real time implementation with ARDUINO Duemilanove
board to the one-link flexible joint robot.
Abstract: This paper presents a tracking control strategy based on Lyapunov approach for nonholonomic wheeled mobile robot. This control strategy consists of two levels. First, a kinematic controller is developed to adjust the right and left wheel velocities. Using this velocity control law, the stability of the tracking error is guaranteed using Lyapunov approach. This kinematic controller cannot be generated directly by the motors. To overcome this problem, the second level of the controllers, dynamic control, is designed. This dynamic control law is developed based on Lyapunov theory in order to track the desired trajectories of the mobile robot. The stability of the tracking error is proved using Lupunov and Barbalat approaches. Simulation results on a nonholonomic wheeled mobile robot are given to demonstrate the feasibility and effectiveness of the presented approach.
Abstract: The paper describes the use of subspace based
identification methods for auto tuning of a state space control system.
The plant is an unstable but self balancing transport robot. Because
of the unstable character of the process it has to be identified
from closed loop input-output data. Based on the identified model
a state space controller combined with an observer is calculated. The
subspace identification algorithm and the controller design procedure
is combined to a auto tuning method. The capability of the approach
was verified in a simulation experiments under different process
conditions.
Abstract: A Fourier series based learning control (FSBLC)
algorithm for tracking trajectories of mechanical systems with
unknown nonlinearities is presented. Two processes are introduced to
which the FSBLC with PD controller is applied. One is a simplified
service robot capable of climbing stairs due to special wheels and
the other is a propeller driven pendulum with nearly the same
requirements on control. Additionally to the investigation of learning
the feed forward for the desired trajectories some considerations on
the implementation of such an algorithm on low cost microcontroller
hardware are made. Simulations of the service robot as well as
practical experiments on the pendulum show the capability of the used
FSBLC algorithm to perform the task of improving control behavior
for repetitive task of such mechanical systems.
Abstract: This paper describes the design process of a 200 MHz Ground Penetrating Radar (GPR) and a battery powered concrete vertical concrete surface climbing mobile robot. The key design feature is a miniaturized 200 MHz dipole antenna using additional radiating arms and procedure records a reduction of 40% in length compared to a conventional antenna. The antenna set is mounted in front of the robot using a servo mechanism for folding and unfolding purposes. The robot’s adhesion mechanism to climb the reinforced concrete wall is based on neodymium permanent magnets arranged in a unique combination to concentrate and maximize the magnetic flux to provide sufficient adhesion force for GPR installation. The experiments demonstrated the robot’s capability of climbing reinforced concrete wall carrying the attached prototype GPR system and perform floor-to-wall transition and vice versa. The developed GPR’s performance is validated by its capability of detecting and localizing an aluminium sheet and a reinforcement bar (rebar) of 12 mm diameter buried under a test rig built of wood to mimic the concrete structure environment. The present robotic GPR system proves the concept of feasibility of undertaking inspection procedure on large concrete structures in hazardous environments that may not be accessible to human inspectors.
Abstract: With the aging of the world population and the
continuous growth in technology, service robots are more and more
explored nowadays as alternatives to healthcare givers or personal
assistants for the elderly or disabled people. Any service robot
should be capable of interacting with the human companion, receive
commands, navigate through the environment, either known or
unknown, and recognize objects. This paper proposes an approach
for object recognition based on the use of depth information and
color images for a service robot. We present a study on two of the
most used methods for object detection, where 3D data is used to
detect the position of objects to classify that are found on horizontal
surfaces. Since most of the objects of interest accessible for service
robots are on these surfaces, the proposed 3D segmentation reduces
the processing time and simplifies the scene for object recognition.
The first approach for object recognition is based on color histograms,
while the second is based on the use of the SIFT and SURF feature
descriptors. We present comparative experimental results obtained
with a real service robot.
Abstract: Centrifugal-casting machine is used in manufacturing
special machine components like multi-layer journal bearing used in
all internal combustion engine, steam, gas turbine and air craft turboengine
where isotropic properties and high precisions are desired.
Moreover, this machine can be used in manufacturing thin wall hightech
machine components like cylinder liners and piston rings of IC
engine and other machine parts like sleeves, and bushes. Heavy-duty
machine component like railway wheel can also be prepared by
centrifugal casting. A lot of technological developments are required
in casting process for production of good casted machine body and
machine parts. Usually defects like blowholes, surface roughness,
chilled surface etc. are found in sand casted machine parts. But these
can be removed by centrifugal casting machine using rotating
metallic die. Moreover, die rotation, its temperature control, and good
pouring practice can contribute to the quality of casting because of
the fact that the soundness of a casting in large part depends upon
how the metal enters into the mold or dies and solidifies. Poor
pouring practice leads to variety of casting defects such as
temperature loss, low quality casting, excessive turbulence, over
pouring etc. Besides these, handling of molten metal is very
unsecured and dangerous for the workers. In order to get rid of all
these problems, the need of an automatic pouring device arises. In
this research work, a robot assisted pouring device and a centrifugal
casting machine are designed, developed constructed and tested
experimentally which are found to work satisfactorily. The robot
assisted pouring device is further modified and developed for using it
in actual metal casting process. Lot of settings and tests are required
to control the system and ultimately it can be used in automation of
centrifugal casting machine to produce high-tech machine parts with
desired precision.
Abstract: Recently attention has been focused on incomplete
spinal cord injuries (SCI) to the central spine caused by pressure on
parts of the white matter conduction pathway, such as the pyramidal
tract. In this paper, we focus on a training robot designed to assist with
primary walking-pattern training. The target patient for this training
robot is relearning the basic functions of the usual walking pattern; it is
meant especially for those with incomplete-type SCI to the central
spine, who are capable of standing by themselves but not of
performing walking motions. From the perspective of human
engineering, we monitored the operator’s actions to the robot and
investigated the movement of joints of the lower extremities, the
circumference of the lower extremities, and exercise intensity with the
machine. The concept of the device was to provide mild training
without any sudden changes in heart rate or blood pressure, which will
be particularly useful for the elderly and disabled. The mechanism of
the robot is modified to be simple and lightweight with the expectation
that it will be used at home.
Abstract: This paper presents modeling and simulation of
flexible robot in an underwater environment. The underwater
environment completely contrasts with ground or space environment.
The robot in an underwater situation is subjected to various dynamic
forces like buoyancy forces, hydrostatic and hydrodynamic forces.
The underwater robot is modeled as Rayleigh beam. The developed
model further allows estimating the deflection of tip in two
directions. The complete dynamics of the underwater robot is
analyzed, which is the main focus of this investigation. The control of
robot trajectory is not discussed in this paper. Simulation is
performed using Symbol Shakti software.
Abstract: This paper investigates simple implicit force control
algorithms realizable with industrial robots. A lot of approaches
already published are difficult to implement in commercial robot
controllers, because the access to the robot joint torques is necessary
or the complete dynamic model of the manipulator is used. In
the past we already deal with explicit force control of a position
controlled robot. Well known schemes of implicit force control are
stiffness control, damping control and impedance control. Using such
algorithms the contact force cannot be set directly. It is further
the result of controller impedance, environment impedance and
the commanded robot motion/position. The relationships of these
properties are worked out in this paper in detail for the chosen
implicit approaches. They have been adapted to be implementable
on a position controlled robot. The behaviors of stiffness control
and damping control are verified by practical experiments. For this
purpose a suitable test bed was configured. Using the full mechanical
impedance within the controller structure will not be practical in the
case when the robot is in physical contact with the environment. This
fact will be verified by simulation.
Abstract: In this paper we propose a discrete tracking control of
nonholonomic mobile robots with two degrees of freedom. The
electromechanical model of a mobile robot moving on a horizontal
surface without slipping, with two rear wheels controlled by two
independent DC electric, and one front roal wheel is considered. We
present backstepping design based on the Euler approximate discretetime
model of a continuous-time plant. Theoretical considerations are
verified by numerical simulation.
Abstract: In this paper, we discuss the performance of applying
hybrid spiral dynamic bacterial chemotaxis (HSDBC) optimisation
algorithm on an intelligent controller for a differential drive robot. A
unicycle class of differential drive robot is utilised to serve as a basis
application to evaluate the performance of the HSDBC algorithm. A
hybrid fuzzy logic controller is developed and implemented for the
unicycle robot to follow a predefined trajectory. Trajectories of
various frictional profiles and levels were simulated to evaluate the
performance of the robot at different operating conditions. Controller
gains and scaling factors were optimised using HSDBC and the
performance is evaluated in comparison to previously adopted
optimisation algorithms. The HSDBC has proven its feasibility in
achieving a faster convergence toward the optimal gains and resulted
in a superior performance.
Abstract: Robotic surgery is used to enhance minimally invasive
surgical procedure. It provides greater degree of freedom for surgical
tools but lacks of haptic feedback system to provide sense of touch to
the surgeon. Surgical robots work on master-slave operation, where
user is a master and robotic arms are the slaves. Current, surgical
robots provide precise control of the surgical tools, but heavily rely
on visual feedback, which sometimes cause damage to the inner
organs. The goal of this research was to design and develop a realtime
Simulink based robotic system to study force feedback
mechanism during instrument-object interaction. Setup includes three
VelmexXSlide assembly (XYZ Stage) for three dimensional
movement, an end effector assembly for forceps, electronic circuit for
four strain gages, two Novint Falcon 3D gaming controllers,
microcontroller board with linear actuators, MATLAB and Simulink
toolboxes. Strain gages were calibrated using Imada Digital Force
Gauge device and tested with a hard-core wire to measure
instrument-object interaction in the range of 0-35N. Designed
Simulink model successfully acquires 3D coordinates from two
Novint Falcon controllers and transfer coordinates to the XYZ stage
and forceps. Simulink model also reads strain gages signal through
10-bit analog to digital converter resolution of a microcontroller
assembly in real time, converts voltage into force and feedback the
output signals to the Novint Falcon controller for force feedback
mechanism. Experimental setup allows user to change forward
kinematics algorithms to achieve the best-desired movement of the
XYZ stage and forceps. This project combines haptic technology
with surgical robot to provide sense of touch to the user controlling
forceps through machine-computer interface.
Abstract: This paper addresses the issue of the autonomous
mobile robot (AMR) navigation task based on the hybrid control
modes. The novel hybrid control mode, based on multi-sensors
information by using the fuzzy approach, has been presented in this
research. The system operates in real time, is robust, enables the robot
to operate with imprecise knowledge, and takes into account the
physical limitations of the environment in which the robot moves,
obtaining satisfactory responses for a large number of different
situations. An experiment is simulated and carried out with a pioneer
mobile robot. From the experimental results, the effectiveness and
usefulness of the proposed AMR obstacle avoidance and navigation
scheme are confirmed. The experimental results show the feasibility,
and the control system has improved the navigation accuracy. The
implementation of the controller is robust, has a low execution time,
and allows an easy design and tuning of the fuzzy knowledge base.
Abstract: This paper presents the hardware implemented and
validation for a special system to assist the unprofessional users of
car with back trailers. The system consists of two platforms; the front
car platform (C) and the trailer platform (T). The main objective is to
control the Trailer platform using the actuators found in the front
platform (c). The mobility of the platform (C) is investigated and
inverse and forward kinematics model is obtained for both platforms
(C) and (T).The system is simulated using Matlab M-file and the
simulation examples results illustrated the system performance. The
system is constructed with a hardware setup for the front and trailer
platform. The hardware experimental results and the simulated
examples outputs showed the validation of the hardware setup.
Abstract: This paper presents a hybrid fuzzy logic control
strategy for a unicycle trajectory following robot on irregular terrains.
In literature, researchers have presented the design of path tracking
controllers of mobile robots on non-frictional surface. In this work,
the robot is simulated to drive on irregular terrains with contrasting
frictional profiles of peat and rough gravel. A hybrid fuzzy logic
controller is utilised to stabilise and drive the robot precisely with the
predefined trajectory and overcome the frictional impact. The
controller gains and scaling factors were optimised using spiral
dynamics optimisation algorithm to minimise the mean square error
of the linear and angular velocities of the unicycle robot. The robot
was simulated on various frictional surfaces and terrains and the
controller was able to stabilise the robot with a superior performance
that is shown via simulation results.
Abstract: The aim of this research is to design and implement line-tracking mobile robot. The robot must follow a line drawn on the floor with different color, avoids hitting moving object like another moving robot or walking people and achieves color sensing. The control system reacts by controlling each of the motors to keep the tracking sensor over the middle of the line. Proximity sensors used to avoid hitting moving objects that may pass in front of the robot. The programs have been written using micro c instructions, then converted into PIC16F887 ATmega48/88/168 microcontrollers counterparts. Practical simulations show that the walking robot accurately achieves line following action and exactly recognizes the colors and avoids any obstacle in front of it.
Abstract: Localization of mobile robots are important tasks for
developing autonomous mobile robots. This paper proposes a method
to estimate positions of a mobile robot using a omnidirectional
camera on the robot. Landmarks for points of references are set
up on a field where the robot works. The omnidirectional camera
which can obtain 360 [deg] around images takes photographs of
these landmarks. The positions of the robots are estimated from
directions of these landmarks that are extracted from the images
by image processing. This method can obtain the robot positions
without accumulative position errors. Accuracy of the estimated
robot positions by the proposed method are evaluated through some
experiments. The results show that it can obtain the positions with
small standard deviations. Therefore the method has possibilities of
more accurate localization by tuning of appropriate offset parameters.
Abstract: In this paper we deal with using Lego Mindstorms in
simulation of robotic systems with respect to cost reduction. Lego
Mindstorms kit contains broad variety of hardware components
which are required to simulate, program and test the robotics systems
in practice. Algorithm programming went in development
environment supplied together with Lego kit as in programming
language C# as well. Algorithm following the line, which we dealt
with in this paper, uses theoretical findings from area of controlling
circuits. PID controller has been chosen as controlling circuit whose
individual components were experimentally adjusted for optimal
motion of robot tracking the line. Data which are determined to
process by algorithm are collected by sensors which scan the
interface between black and white surfaces followed by robot. Based
on discovered facts Lego Mindstorms can be considered for low-cost
and capable kit to simulate real robotics systems.
Abstract: Methods for measuring or estimating ground shape by a laser range finder and a vision sensor (Exteroceptive sensors) have critical weaknesses in terms that these methods need a prior database built to distinguish acquired data as unique surface conditions for driving. Also, ground information by Exteroceptive sensors does not reflect the deflection of ground surface caused by the movement of UGVs. Therefore, this paper proposes a method of recognizing exact and precise ground shape using an Inertial Measurement Unit (IMU) as a proprioceptive sensor. In this paper, firstly this method recognizes the attitude of a robot in real-time using IMU and compensates attitude data of a robot with angle errors through analysis of vehicle dynamics. This method is verified by outdoor driving experiments of a real mobile robot.