Abstract: Two geometrically nonlinear plate theories, based either on first- or third-order transverse shear deformation theory are used for finite element modeling and simulation of the transient response of smart structures incorporating piezoelectric layers. In particular the time histories of nonlinear vibrations and sensor voltage output of a thin beam with a piezoelectric patch bonded to the surface due to an applied step force are studied.
Abstract: The effect of autofrettage process in strain hardened
thick-walled pressure vessels has been investigated theoretically by
finite element modeling. Equivalent von Mises stress is used as yield
criterion to evaluate the optimum autofrettage pressure and the
optimum radius of elastic-plastic junction. It has been observed that
the optimum autofrettage pressure increases along with the working
pressure. For two different working pressures, the effect of the ratio
of outer to inner radius (b/a=k) value on the optimum autofrettage
pressure is also noticed. The Optimum autofrettage pressure solely
depends on K value rather than on the inner or outer radius.
Furthermore, percentage reduction of von Mises stresses is compared
for different working pressures and different k values. Maximum von
Mises stress developed at different autofrettage pressure is equated
for elastic perfectly plastic and elastic-plastic material with different
slope of strain hardening segment. Cylinder material having higher
slope of strain hardening segment provides better benedictions in the
autofrettage process.
Abstract: The human knee joint has a three dimensional
geometry with multiple body articulations that produce complex
mechanical responses under loads that occur in everyday life and
sports activities. To produce the necessary joint compliance and
stability for optimal daily function various menisci and ligaments are
present while muscle forces are used to this effect. Therefore,
knowledge of the complex mechanical interactions of these load
bearing structures is necessary when treatment of relevant diseases is
evaluated and assisting devices are designed.
Numerical tools such as finite element analysis are suitable for
modeling such joints in order to understand their physics. They have
been used in the current study to develop an accurate human knee
joint and model its mechanical behavior. To evaluate the efficacy of
this articulated model, static load cases were used for comparison
purposes with previous experimentally verified modeling works
drawn from literature.
Abstract: A three-dimensional finite element modeling for austenitic stainless steel AISI 304 annealed condition sheets of 1.0 mm thickness are developed using ABAQUS® software. This includes spot welded and weld bonded joints models. Both models undergo thermal heat caused by spot welding process and then are subjected to axial load up to the failure point. The properties of elastic and plastic regions, modulus of elasticity, fracture limit, nugget and heat affected zones are determined. Complete loaddisplacement curve for each joining model is obtained and compared with the experiment data and with the finite element models without including the effect of thermal process. In general, the results obtained for both spot welded and weld-bonded joints affected by thermal process showed an excellent agreement with the experimental data.
Abstract: Bone material is treated as heterogeneous and hierarchical in nature therefore appropriate size of bone specimen is required to analyze its tensile properties at a particular hierarchical level. Tensile properties of cortical bone are important to investigate the effect of drug treatment, disease and aging as well as for development of computational and analytical models. In the present study tensile properties of buffalo as well as goat femoral and tibiae cortical bone are analyzed using sub-size tensile specimens. Femoral cortical bone was found to be stronger in tension as compared to the tibiae cortical bone and the tensile properties obtained using sub-size specimens show close resemblance with the tensile properties of full-size cortical specimens. A two dimensional finite element (FE) modal was also applied to simulate the tensile behavior of sub-size specimens. Good agreement between experimental and FE model was obtained for sub-size tensile specimens of cortical bone.
Abstract: Organ motion, especially respiratory motion, is a technical challenge to radiation therapy planning and dosimetry. This motion induces displacements and deformation of the organ tissues within the irradiated region which need to be taken into account when simulating dose distribution during treatment. Finite element modeling (FEM) can provide a great insight into the mechanical behavior of the organs, since they are based on the biomechanical material properties, complex geometry of organs, and anatomical boundary conditions. In this paper we present an original approach that offers the possibility to combine image-based biomechanical models with particle transport simulations. We propose a new method to map material density information issued from CT images to deformable tetrahedral meshes. Based on the principle of mass conservation our method can correlate density variation of organ tissues with geometrical deformations during the different phases of the respiratory cycle. The first results are particularly encouraging, as local error quantification of density mapping on organ geometry and density variation with organ motion are performed to evaluate and validate our approach.
Abstract: Arc welding is an important joining process widely used in many industrial applications including production of automobile, ships structures and metal tanks. In welding process, the moving electrode causes highly non-uniform temperature distribution that leads to residual stresses and different deviations, especially buckling distortions in thin plates. In order to control the deviations and increase the quality of welded plates, a fixture can be used as a practical and low cost method with high efficiency. In this study, a coupled thermo-mechanical finite element model is coded in the software ANSYS to simulate the behavior of thin plates located by a 3-2-1 positioning system during the welding process. Computational results are compared with recent similar works to validate the finite element models. The agreement between the result of proposed model and other reported data proves that finite element modeling can accurately predict the behavior of welded thin plates.
Abstract: In construction of any structure, the aesthetic and utility values should be considered in such a way as to make the structure cost-effective. Most structures are composed of elements and joints which are very critical in any skeletal space structure because they majorly determine the performance of the structure. In early times, most space structures were constructed using rigid joints which had the advantage of better performing structures as compared to pin-jointed structures but with the disadvantage of requiring all the construction work to be done on site. The discovery of semi-rigid joints now enables connections to be prefabricated and quickly assembled on site while maintaining good performance. In this paper, cost-effective is discussed basing on strength of connectors at the joints, buckling of joints and overall structure, and the effect of initial geometrical imperfections. Several existing joints are reviewed by classifying them into categories and discussing where they are most suited and how they perform structurally. Also, finite element modeling using ABAQUS is done to determine the buckling behavior. It is observed that some joints are more economical than others. The rise to span ratio and imperfections are also found to affect the buckling of the structures. Based on these, general principles that guide the design of cost-effective joints and structures are discussed.
Abstract: Endovascular aneurysm repair is a new and minimally invasive repair for patients with abdominal aortic aneurysm (AAA). This method has potential advantages that are incomparable with other repair methods. However, the enlargement of aneurysm in the absence of endoleak, which is known as endotension, may occur as one of post-operative compliances of this method. Typically, endotension is mainly as a result of pressure transmitted to aneurysm sac by endovascular installed graft. After installation of graft the aneurysm sac reduces significantly but remains non-zero. There are some factors which affect this pressure transmitted. In this study, the geometry features of installed vascular graft have been considered. It is inferred that graft neck angle and iliac bifurcation angle are two factors which can affect the drag force on graft and consequently the pressure transmitted to aneurysm.
Abstract: In present work, prediction the effect of nose radius, rz (mm) on the equivalent strain (PEEQ) and surface finish during the machining of titanium alloy (Ti-6Al-4V) through orthogonal cutting process. The results were performed at several of the nose radiuses, rz (mm) while the cutting speed, vc (m/min), feed rate, f (mm/tooth) and depth of cut, d (mm) were remained constant. The equivalent plastic strain (PEEQ) was estimated by using finite element modeling (FEM) and applied through ABAQUS/EXPLICIT software. The simulation results led to conclude that the equivalent plastic strain (PEEQ) was increased and surface roughness (Ra) decreased when increasing nose radius, rz (mm) during the machining of titanium alloy (Ti–6Al–4V) in dry cutting conditions.
Abstract: During the last decade ultrafine grained (UFG) and nano-structured (NS) materials have experienced a rapid development. In this research work finite element analysis has been carried out to investigate the plastic strain distribution in equal channel angular process (ECAP). The magnitudes of Standard deviation (S. D.) and inhomogeneity index (Ci) were compared for different ECAP passes. Verification of a three-dimensional finite element model was performed with experimental tests. Finally the mechanical property including impact energy of ultrafine grained pure commercially pure Aluminum produced by severe plastic deformation method has been examined. For this aim, equal channel angular pressing die with the channel angle, outer corner angle and channel diameter of 90°, 20° and 20mm had been designed and manufactured. Commercial pure Aluminum billets were ECAPed up to four passes by route BC at the ambient temperature. The results indicated that there is a great improvement at the hardness measurement, yield strength and ultimate tensile strength after ECAP process. It is found that the magnitudes of HV reach 67HV from 21HV after the final stage of process. Also, about 330% and 285% enhancement at the YS and UTS values have been obtained after the fourth pass as compared to the as-received conditions, respectively. On the other hand, the elongation to failure and impact energy have been reduced by 23% and 50% after imposing four passes of ECAP process, respectively.
Abstract: The objective of this research is to examine the shear thinning behaviour of mixing flow of non-Newtonian fluid like toothpaste in the dissolution container with rotating stirrer. The problem under investigation is related to the chemical industry. Mixing of fluid is performed in a cylindrical container with rotating stirrer, where stirrer is eccentrically placed on the lid of the container. For the simulation purpose the associated motion of the fluid is considered as revolving of the container, with stick stirrer. For numerical prediction, a time-stepping finite element algorithm in a cylindrical polar coordinate system is adopted based on semi-implicit Taylor-Galerkin/pressure-correction scheme. Numerical solutions are obtained for non-Newtonian fluids employing power law model. Variations with power law index have been analysed, with respect to the flow structure and pressure drop.
Abstract: This paper deals with the analysis of active constrained layer damping (ACLD) of doubly curved laminated composite shells using active fiber composite (AFC) materials. The constraining layer of the ACLD treatment has been considered to be made of the AFC materials. A three dimensional energy based finite element model of the smart doubly curved laminated composite shell integrated with a patch of such ACLD treatment has been developed to demonstrate the performance of the patch on enhancing the damping characteristics of the doubly curved laminated composite shells. Particular emphasis has been placed on studying the effect of variation of piezoelectric fiber orientation angle in the constraining AFC layer on the control authority of the ACLD patch.
Abstract: Sandwich panels are widely used in the construction
industry for their ease of assembly, light weight and efficient thermal
performance. They are composed of two RC thin outer layers
separated by an insulating inner layer. In this research the inner
insulating layer is made of lightweight Autoclaved Aerated Concrete
(AAC) blocks which has good thermal insulation properties and yet
possess reasonable mechanical strength. The shear strength of the
AAC infill is relied upon to replace the traditionally used insulating
foam and to provide the shear capacity of the panel. A
comprehensive experimental program was conducted on full scale
sandwich panels subjected to bending. In this paper, detailed
numerical modeling of the tested sandwich panels is reported. Nonlinear
3-D finite element modeling of the composite action of the
sandwich panel is developed using ANSYS. Solid elements with
different crashing and cracking capabilities and different constitutive
laws were selected for the concrete and the AAC. Contact interface
elements are used in this research to adequately model the shear
transfer at the interface between the different layers. The numerical
results showed good correlation with the experimental ones
indicating the adequacy of the model in estimating the loading
capacity of panels.
Abstract: This paper presents the adaptive control scheme
with sliding mode compensator for vibration control problem
in the presence of disturbance. The dynamic model of the
flexible cantilever beam using finite element modeling is
derived. The adaptive control with sliding mode compensator
using output feedback for output tracking is developed to
reject the external disturbance, and to improve the tracking
performance. Satisfactory simulation results verify that the
effectiveness of adaptive control scheme with sliding mode
compensator.
Abstract: In the present work, behavior of inoxydable steel as
reinforcement bar in composite concrete is being investigated. The
bar-concrete adherence in reinforced concrete (RC) beam is studied
and focus is made on the tension stiffening parameter. This study
highlighted an approach to observe this interaction behavior in
bending test instead of direct tension as per reported in many
references. The approach resembles actual loading condition of the
structural RC beam. The tension stiffening properties are then
applied to numerical finite element analysis (FEA) to verify their
correlation with laboratory results. Comparison with laboratory
shows a good correlation between the two. The experimental settings
is able to determine tension stiffening parameters in RC beam and
the modeling strategies made in ABAQUS can closely represent the
actual condition. Tension stiffening model used can represent the
interaction properties between inoxydable steel and concrete.
Abstract: Human middle-ear is the key component of the
auditory system. Its function is to transfer the sound waves through
the ear canal to provide sufficient stimulus to the fluids of the inner
ear. Degradation of the ossicles that transmit these sound waves from
the eardrum to the inner ear leads to hearing loss. This problem can
be overcome by replacing one or more of these ossicles by middleear
prosthesis. Designing such prosthesis requires a comprehensive
knowledge of the biomechanics of the middle-ear. There are many
finite element modeling approaches developed to understand the
biomechanics of the middle ear. The available models in the
literature, involve high computation time. In this paper, we propose a
simplified model which provides a reasonably accurate result with
much less computational time. Simulation results indicate a
maximum sound pressure gain of 10 dB at 5500 Hz.
Abstract: Resistance spot welding process comprises of electric,
thermal and mechanical phenomenon, which makes this process
complex and highly non-linear and thus, it becomes difficult to model
it. In order to obtain good weld nugget during spot welding, hit and
trial welds are usually done which is very costly. Therefore the
numerical simulation research has been conducted to understand the
whole process. In this paper three different cases were analyzed by
varying the tip contact area and it was observed that, with the
variation of tip contact area the nugget formation at the faying
surface is affected. The tip contact area of the welding electrode
becomes large with long welding cycles. Therefore in order to
maintain consistency of nugget formation during the welding process,
the current compensation in control feedback is required. If the
contact area of the welding electrode tip is reduced, a large amount of
current flows through the faying surface, as a result of which
sputtering occurs.
Abstract: Reliable information about tool temperature
distribution is of central importance in metal cutting. In this study,
tool-chip interface temperature was determined in cutting of ST37
steel workpiece by applying HSS as the cutting tool in dry turning.
Two different approaches were implemented for temperature
measuring: an embedded thermocouple (RTD) in to the cutting tool
and infrared (IR) camera. Comparisons are made between
experimental data and results of MSC.SuperForm and FLUENT
software.
An investigation of heat generation in cutting tool was performed
by varying cutting parameters at the stable cutting tool geometry and
results were saved in a computer; then the diagrams of tool
temperature vs. various cutting parameters were obtained. The
experimental results reveal that the main factors of the increasing
cutting temperature are cutting speed (V ), feed rate ( S ) and depth
of cut ( h ), respectively. It was also determined that simultaneously
change in cutting speed and feed rate has the maximum effect on
increasing cutting temperature.
Abstract: In this paper, a new formulation for acoustics coupled with linear elasticity is presented. The primary objective of the work is to develop a three dimensional hp adaptive finite element method code destinated for modeling of acoustics of human head. The code will have numerous applications e.g. in designing hearing protection devices for individuals working in high noise environments. The presented work is in the preliminary stage. The variational formulation has been implemented and tested on a sequence of meshes with concentric multi-layer spheres, with material data representing the tissue (the brain), skull and the air. Thus, an efficient solver for coupled elasticity/acoustics problems has been developed, and tested on high contrast material data representing the human head.