Abstract: Experimental study of natural convection heat transfer
inside smooth and rough surfaces of vertical and inclined equilateral
triangular channels of different inclination angles with a uniformly
heated surface are performed. The inclination angle is changed from
15º to 90º. Smooth and rough surface of average roughness (0.02mm)
are used and their effect on the heat transfer characteristics are
studied. The local and average heat transfer coefficients and Nusselt
number are obtained for smooth and rough channels at different heat
flux values, different inclination angles and different Rayleigh
numbers (Ra) 6.48 × 105 ≤ Ra ≤ 4.78 × 106. The results show that
the local Nusselt number decreases with increase of axial distance
from the lower end of the triangular channel to a point near the upper
end of channel, and then, it slightly increases. Higher values of local
Nusselt number for rough channel along the axial distance compared
with the smooth channel. The average Nusselt number of rough
channel is higher than that of smooth channel by about 8.1% for
inclined case at θ = 45o and 10% for vertical case. The results
obtained are correlated using dimensionless groups for both rough
and smooth surfaces of the inclined and vertical triangular channels.
Abstract: In the current work, a three-dimensional geometry of a
75% stenosed blood vessel is analyzed. Large eddy simulation (LES)
with the help of a dynamic subgrid scale Smagorinsky model is
applied to model the turbulent pulsatile flow. The geometry, the
transmural pressure and the properties of the blood and the elastic
boundary were based on clinical measurement data. For the flexible
wall model, a thin solid region is constructed around the 75%
stenosed blood vessel. The deformation of this solid region was
modelled as a deforming boundary to reduce the computational cost
of the solid model. Fluid-structure interaction is realized via a twoway
coupling between the blood flow modelled via LES and the
deforming vessel. The information of the flow pressure and the wall
motion was exchanged continually during the cycle by an arbitrary
Lagrangian-Eulerian method. The boundary condition of current time
step depended on previous solutions. The fluctuation of the velocity
in the post-stenotic region was analyzed in the study. The axial
velocity at normalized position Z=0.5 shows a negative value near
the vessel wall. The displacement of the elastic boundary was
concerned in this study. In particular, the wall displacement at the
systole and the diastole were compared. The negative displacement at
the stenosis indicates a collapse at the maximum velocity and the
deceleration phase.
Abstract: Background - The TrendCare Patient Dependency
System is currently used by a large number of maternity Services
across Australia, New Zealand and Singapore. In 2012, 2013 and
2014 validation studies were initiated in all three countries to validate
the acuity tools used for women in labour, and postnatal mothers and
babies. This paper will present the findings of the validation study.
Aim - The aim of this study was to; identify if the care hours
provided by the TrendCare acuity system was an accurate reflection
of the care required by women and babies; obtain evidence of
changes required to acuity indicators and/or category timings to
ensure the TrendCare acuity system remains reliable and valid across
a range of maternity care models in three countries.
Method - A non-experimental action research methodology was
used across maternity services in four District Health Boards in New
Zealand, a large tertiary and a large secondary maternity service in
Singapore and a large public maternity service in Australia.
Standardised data collection forms and timing devices were used to
collect midwife contact times, with women and babies included in the
study. Rejection processes excluded samples when care was not
completed/rationed, and contact timing forms were incomplete. The
variances between actual timed midwife/mother/baby contact and the
TrendCare acuity category times were identified and investigated.
Results - Thirty two (88.9%) of the 36 TrendCare acuity category
timings, fell within the variance tolerance levels when compared to
the actual timings recorded for midwifery care. Four (11.1%)
TrendCare categories provided less minutes of care than the actual
timings and exceeded the variance tolerance level. These were all
night shift category timings. Nine postnatal categories were not able
to be compared as the sample size for these categories was
statistically insignificant. 100% of labour ward TrendCare categories
matched actual timings for midwifery care, all falling within the
variance tolerance levels.
The actual time provided by core midwifery staff to assist lead
maternity carer (LMC) midwives in New Zealand labour wards
showed a significant deviation to previous studies. The findings of
the study demonstrated the need for additional time allocations in
TrendCare to accommodate an increased level of assistance given to
LMC midwives.
Conclusion - The results demonstrated the importance of regularly
validating the TrendCare category timings with actual timings of the
care hours provided. It was evident from the findings that variances
to models of care and length of stay in maternity units have increased
midwifery workloads on the night shift. The level of assistance
provided by the core labour ward staff to the LMC midwife has
increased substantially.
Outcomes - As a consequence of this study, changes were made to
the night duty TrendCare maternity categories, additional acuity
indicators were developed and times for assisting LMC midwives in
labour ward increased. The updated TrendCare version was delivered
to maternity services in 2014.
Abstract: Employer branding is considered as a useful tool for
addressing the global-local problem facing complex organisations
that have operations scattered across the globe and face challenges of
dealing with the local environment alongside. Despite being an
established field of study within the Western developed world, there
is little empirical evidence concerning the relevance of employer
branding to global companies that operate in the under-developed
economies. This paper fills this gap by gaining rich insight into the
implementation of employer branding programs in a foreign
multinational operating in Pakistan dealing with the global-local
problem. The study is qualitative in nature and employs semistructured
and focus group interviews with senior/middle managers
and local frontline employees to deeply examine the phenomenon in
case organisation. Findings suggest that authenticity is required in
employer brands to enable them to respond to the local needs thereby
leading to the resolution of the global-local problem. However, the
role of signaling theory is key to the development of authentic
employer brands as it stresses on the need to establish an efficient and
effective signaling environment where in signals travel in both
directions (from signal designers to receivers and backwards) and
facilitate firms with the global-local problem. The paper also
identifies future avenues of research for the employer branding field.
Abstract: Predicting the collapse potential of a structure during
earthquakes is an important issue in earthquake engineering. Many
researchers proposed different methods to assess the collapse
potential of structures under the effect of strong ground motions.
However most of them did not consider degradation and softening
effect in hysteretic behavior. In this study, collapse potential of
SDOF systems caused by dynamic instability with stiffness and
strength degradation has been investigated. An equation was
proposed for the estimation of collapse period of SDOF system which
is a limit value of period for dynamic instability. If period of the
considered SDOF system is shorter than the collapse period then the
relevant system exhibits dynamic instability and collapse occurs.
Abstract: This article presents modeling studies of NiAl alloy
under solid-particle erosion and liquid-drop erosion. In the
solid-particle erosion simulation, attention is paid to the oxide scale
thickness variation on the alloy in high-temperature erosion
environments. The erosion damage is assumed to be deformation wear
and cutting wear mechanisms, incorporating the influence of the oxide
scale on the eroded surface; thus the instantaneous oxide thickness is
the result of synergetic effect of erosion and oxidation. For liquid-drop
erosion, special interest is in investigating the effects of drop velocity
and drop size on the damage of the target surface. The models of
impact stress wave, mean depth of penetration, and maximum depth of
erosion rate (Max DER) are employed to develop various maps for
NiAl alloy, including target thickness vs. drop size (diameter), rate of
mean depth of penetration (MDRP) vs. drop impact velocity, and
damage threshold velocity (DTV) vs. drop size.
Abstract: Air-cooled Blast Furnace Slag Aggregate (BFSA) is
usually referred to as a material providing for unique properties of
concrete. On the other hand, negative influences are also presented in
many aspects. The freeze-thaw resistance of concrete is dependent on
many factors, including regional specifics and when a concrete mix is
specified it is still difficult to tell its exact freeze-thaw resistance due
to the different components affecting it. An important consideration
in working with BFSA is the granularity and whether slag is sorted or
not. The experimental part of the article represents a comparative
testing of concrete using both the sorted and unsorted BFSA through
the freeze-thaw resistance as an indicator of durability. Unsorted
BFSA is able to be successfully used for concretes as they are
specified for exposure class XF4 with providing that the type of
cement is precisely selected.
Abstract: In general, classical methods such as maximum
likelihood (ML) and least squares (LS) estimation methods are used
to estimate the shape parameters of the Burr XII distribution.
However, these estimators are very sensitive to the outliers. To
overcome this problem we propose alternative robust estimators
based on the M-estimation method for the shape parameters of the
Burr XII distribution. We provide a small simulation study and a real
data example to illustrate the performance of the proposed estimators
over the ML and the LS estimators. The simulation results show that
the proposed robust estimators generally outperform the classical
estimators in terms of bias and root mean square errors when there
are outliers in data.
Abstract: In general, codes and regulations consider seismic
loads only for completed structures of the bridges while, evaluation
of incomplete structure of bridges, especially those constructed by
free cantilever method, under these loads is also of great importance.
Hence, this research tried to study the behavior of incomplete
structure of common bridge type (box girder bridge), in construction
phase under vertical seismic loads. Subsequently, the paper provided
suitable guidelines and solutions to resist this destructive
phenomenon. Research results proved that use of preventive methods
can significantly reduce the stresses resulted from vertical seismic
loads in box cross sections to an acceptable range recommended by
design codes.
Abstract: High performance turf reinforcement mat (HPTRM) is
one of the most advanced flexible armoring technologies for severe
erosion challenges. The effect of turbulence on the slope stability of
an earthen levee strengthened by high performance turf reinforcement
mat (HPTRM) is investigated in this study for combined storm surge
and wave overtopping conditions. The results show that turbulence
has strong influence on the slope stability during the combined storm
surge and wave overtopping conditions. Among the surge height,
peak wave force and turbulent force. The turbulent force has the
ability to stabilize the earthen levee at the large wave force the
turbulent force has strongest effect on the FS. The surge storm acts as
an independent force on the slope stability of the earthen levee. It just
adds to the effects of the turbulent force and wave force on the slope
stability of HPTRM strengthened levee.
Abstract: Poly bag and mulch films for agricultural field caused
pose environmental problem due to the non-degradable plastics
wastes upon disposal. Thus, a degradable poly bag was designed with
hybrid sago starch (SS) and polyvinyl alcohol (PVA). Two Different
blended compositions of SS and PVA hybrid have been compounded.
Then, the hybrids blended are mixed with linear line density
polyethylene (LLDPE) resin to fabricate poly bag film through
conventional film blowing process. Samples of LLDPE, SS and PVA
hybrid film were exposed to UV light and soil burial. The weight
losses were determined during degradation process. Hybrid film by
degradation of starch was found to hydrolyze and hydroxyl groups
decrease on esterification upon exposure to soil burial and uv
radiation. It was found out that, the hybrid film for 60% of SS
composition showed greatest degradation in soil and UV radiation.
Abstract: Freshly laid eggs from green turtles, Chelonia mydas,
were randomly collected from Ras Al-Hadd Reserve, Oman.
Eggshells taken from eggs and sand collected from the body chamber
were analyzed for eight heavy metals (Al, Br, Cd, Co, Cu, Fe, S, and
Zn) using inductively coupled plasma mass spectrometry (ICP).
Heavy metal concentrations varied significantly (P
Abstract: The objective of this work is to study the effect of two
key factors - external magnetic field and applied current density
during template-based electrodeposition of nickel nanowires using an
electrode distance of 20 mm. Morphology, length, crystallite size and
crystallographic characterization of the grown nickel nanowires at an
electrode distance of 20mm are presented. For this electrode distance
of 20 mm, these two key electrodeposition factors when coupled was
found to reduce crystallite size with a higher growth length and
preferred orientation of Ni crystals. These observed changes can be
inferred to be due to coupled interaction forces induced by the
intensity of applied electric field (current density) and external
magnetic field known as magnetohydrodynamic (MHD) effect during
the electrodeposition process.
Abstract: The paper deals with possibilities of interpretation of
iron ore reducibility tests. It presents a mathematical model
developed at Centre ENET, VŠB – Technical University of Ostrava,
Czech Republic for an evaluation of metallurgical material of blast
furnace feedstock such as iron ore, sinter or pellets. According to the
data from the test, the model predicts its usage in blast furnace
technology and its effects on production parameters of shaft
aggregate. At the beginning, the paper sums up the general concept
and experience in mathematical modelling of iron ore reduction. It
presents basic equation for the calculation and the main parts of the
developed model. In the experimental part, there is an example of
usage of the mathematical model. The paper describes the usage of
data for some predictive calculation. There are presented material,
method of carried test of iron ore reducibility. Then there are
graphically interpreted effects of used material on carbon
consumption, rate of direct reduction and the whole reduction
process.
Abstract: The problem of toughening in brittle materials
reinforced by fibers is complex, involving all of the mechanical
properties of fibers, matrix and the fiber/matrix interface, as well as
the geometry of the fiber. Development of new numerical methods
appropriate to toughening simulation and analysis is necessary. In
this work, we have performed simulations and analysis of toughening
in brittle matrix reinforced by randomly distributed fibers by means
of the discrete elements method. At first, we put forward a
mechanical model of toughening contributed by random fibers. Then
with a numerical program, we investigated the stress, damage and
bridging force in the composite material when a crack appeared in the
brittle matrix. From the results obtained, we conclude that: (i) fibers
of high strength and low elasticity modulus are beneficial to
toughening; (ii) fibers of relatively high elastic modulus compared to
the matrix may result in substantial matrix damage due to spalling
effect; (iii) employment of high-strength synthetic fibers is a good
option for toughening. We expect that the combination of the discrete
element method (DEM) with the finite element method (FEM) can
increase the versatility and efficiency of the software developed. The
present work can guide the design of ceramic composites of high
performance through the optimization of the parameters.
Abstract: The construction industry has been demonstrating
increased growth and importance in Brazil’s national economic
development. This study aims to evaluate the financial performance
of the leading companies in the construction sector in Brazil in the
period from 2009 to 2012. An analysis is made of the capital
structure, liquidity, and profitability of the six largest companies in
the construction sector in Brazil: Brookfield, Cyrela, Gafisa, MRV,
PDG and Rossi. The results are then compared with standard industry
ratios. It was found that among the companies analyzed, MRV and
Cyrela showed the best relative performance in the period under
consideration.
Abstract: This paper discusses the value theory in cultural
heritage and the value theory in environmental economics. Two
economic views of the value theory are compared, within the field of
cultural heritage maintenance and within the field of the environment.
The main aims are to find common features in these two differently
structured theories under the layer of differently defined terms as well
as really differing features of these two approaches; to clear the
confusion which stems from different terminology as in fact these
terms capture the same aspects of reality; and to show possible
inspiration these two perspectives can offer one another. Another aim
is to present these two value systems in one value framework. First,
important moments of the value theory from the economic
perspective are presented, leading to the marginal revolution of (not
only) the Austrian School. Then the theory of value within cultural
heritage and environmental economics are explored. Finally,
individual approaches are compared and their potential mutual
inspiration searched for.
Abstract: In this paper, we introduced a gradient-based inverse
solver to obtain the missing boundary conditions based on the
readings of internal thermocouples. The results show that the method
is very sensitive to measurement errors, and becomes unstable when
small time steps are used. The artificial neural networks are shown to
be capable of capturing the whole thermal history on the run-out
table, but are not very effective in restoring the detailed behavior of
the boundary conditions. Also, they behave poorly in nonlinear cases
and where the boundary condition profile is different.
GA and PSO are more effective in finding a detailed
representation of the time-varying boundary conditions, as well as in
nonlinear cases. However, their convergence takes longer. A
variation of the basic PSO, called CRPSO, showed the best
performance among the three versions. Also, PSO proved to be
effective in handling noisy data, especially when its performance
parameters were tuned. An increase in the self-confidence parameter
was also found to be effective, as it increased the global search
capabilities of the algorithm. RPSO was the most effective variation
in dealing with noise, closely followed by CRPSO. The latter
variation is recommended for inverse heat conduction problems, as it
combines the efficiency and effectiveness required by these
problems.
Abstract: In this paper, the problem of steady laminar boundary
layer flow and heat transfer over a permeable exponentially
stretching/shrinking sheet with generalized slip velocity is
considered. The similarity transformations are used to transform the
governing nonlinear partial differential equations to a system of
nonlinear ordinary differential equations. The transformed equations
are then solved numerically using the bvp4c function in MATLAB.
Dual solutions are found for a certain range of the suction and
stretching/shrinking parameters. The effects of the suction parameter,
stretching/shrinking parameter, velocity slip parameter, critical shear
rate and Prandtl number on the skin friction and heat transfer
coefficients as well as the velocity and temperature profiles are
presented and discussed.
Abstract: The convective heat and mass transfer in nanofluid
flow through a porous media due to a permeable stretching sheet with
magnetic field, viscous dissipation, chemical reaction and Soret
effects are numerically investigated. Two types of nanofluids, namely
Cu-water and Ag-water were studied. The governing boundary layer
equations are formulated and reduced to a set of ordinary differential
equations using similarity transformations and then solved
numerically using the Keller box method. Numerical results are
obtained for the skin friction coefficient, Nusselt number and
Sherwood number as well as for the velocity, temperature and
concentration profiles for selected values of the governing
parameters. Excellent validation of the present numerical results has
been achieved with the earlier linearly stretching sheet problems in
the literature.