Abstract: Under active stress conditions, a rigid cantilever
retaining wall tends to rotate about a pivot point located within the
embedded depth of the wall. For purely granular and cohesive soils, a
methodology was previously reported called minimization of moment
ratio to determine the location of the pivot point of rotation. The
usage of this new methodology is to estimate the rotational stability
safety factor. Moreover, the degree of improvement required in a
backfill to get a desired safety factor can be estimated by the concept
of the shear strength demand. In this article, the accuracy of this
method for another type of cantilever walls called Contiguous Bored
Pile (CBP) retaining wall is evaluated by using physical modeling
technique. Based on observations, the results of moment ratio
minimization method are in good agreement with the results of the
carried out physical modeling.
Abstract: In this work, the Ictalurus punctatus species estimated
available physical habitat is compared with the estimated physical
habitat for the same but modified river reach, with the aim of creating
a linear park, along a length of 5 500 m.
To determine the effect of ecological park construction, on
physical habitat of the Lerma river stretch of study, first, the available
habitat for the Ictalurus punctatus species was estimated through the
simulation of the physical habitat, by using surveying, hydraulics,
and habitat information gotten at the river reach in its actual situation.
Second, it was estimated the available habitat for the above species,
upon the simulation of the physical habitat through the proposed
modification for the ecological park creation. Third, it is presented a
comparison between both scenarios in terms of available habitat
estimated for Ictalurus punctatus species, concluding that in cases of
adult and spawning life stages, changes in the channel to create an
ecological park would produce a considerable loss of potentially
usable habitat (PUH), while in the case of the juvenile life stage PUH
remains virtually unchanged, and in the case of life stage fry the PUH
would increase due to the presence of velocities and depths of lesser
magnitude, due to the presence of minor flow rates and lower volume
of the wet channel.
It is expected that habitat modification for linear park construction
may produce the lack of Ictalurus punktatus species conservation at
the river reach of the study.
Abstract: This paper reports the development and application of a 2D1 depth-averaged model. The main goal of this contribution is to apply the depth averaged equations to a wind park model in which the treatment of the geometry, introduced on the mathematical model by the mass and momentum source terms. The depth-averaged model will be used in future to find the optimal position of wind turbines in the wind park. κ − ε and 2D LES turbulence models were consider in this article. 2D CFD2 simulations for one hill was done to check the depth-averaged model in practise.
Abstract: This study was aimed to investigate the machining
stability of a spindle tool with different preloaded amount. To this end,
the vibration tests were conducted on the spindle unit with different
preload to assess the dynamic characteristics and machining stability
of the milling machine. Current results demonstrate that the tool tip
frequency response characteristics and the machining stabilities in X
and Y direction are affected to change due to the different preload of
spindle bearings. As found from the results, a high preloaded spindle
tool shows higher limited cutting depth at mid position, while a spindle
with low preload shows a higher limited depth. This indicates that the
machining stability of a milling machine is affected to vary by the
spindle unit when it was assembled with different bearing preload.
Abstract: There are many perceived advantages of microwave
ablation have driven researchers to develop innovative antennas to
effectively treat deep-seated, non-resectable hepatic tumors. In this
paper a coaxial antenna with a miniaturized sleeve choke has been
discussed for microwave interstitial ablation therapy, in order to
reduce backward heating effects irrespective of the insertion depth
into the tissue. Two dimensional Finite Element Method (FEM) is
used to simulate and measure the results of miniaturized sleeve choke
antenna. This paper emphasizes the importance of factors that can
affect simulation accuracy, which include mesh resolution, surface
heating and reflection coefficient. Quarter wavelength choke
effectiveness has been discussed by comparing it with the unchoked
antenna with same dimensions.
Abstract: Experimental studies to investigate the depth of the
scour conducted at a side-weir intersection located at the 1800 curved
flume which located Hydraulic Laboratory of Yıldız Technical
University, Istanbul, Turkey. Side weirs were located at the middle of
the straight part of the main channel. Three different lengths (25, 40
and 50 cm) and three different weir crest height (7, 10 and 12 cm) of
the side weir placed on the side weir station. There is no scour when
the material is only kaolin. Therefore, the cohesive bed was prepared
by properly mixing clay material (kaolin) with 31% sand in all
experiments. Following 24h consolidation time, in order to observe
the effect of flow intensity on the scour depth, experiments were
carried out for five different upstream Froude numbers in the range of
0.33-0.81.
As a result of this study the relation between scour depth and
upstream flow intensity as a function of time have been established.
The longitudinal velocities decreased along the side weir; towards the
downstream due to overflow over the side-weirs. At the beginning,
the scour depth increases rapidly with time and then asymptotically
approached constant values in all experiments for all side weir
dimensions as in non-cohesive sediment. Thus, the scour depth
reached equilibrium conditions. Time to equilibrium depends on the
approach flow intensity and the dimensions of side weirs. For
different heights of the weir crest, dimensionless scour depths
increased with increasing upstream Froude number. Equilibrium
scour depths which formed 7 cm side-weir crest height were obtained
higher than that of the 12 cm side-weir crest height. This means when
side-weir crest height increased equilibrium scour depths decreased.
Although the upstream side of the scour hole is almost vertical, the
downstream side of the hole is inclined.
Abstract: Purpose: The study aimed to assess the depressant or
antidepressant effects of several Nonsteroidal Anti-Inflammatory
Drugs (NSAIDs) in mice: the selective cyclooxygenase-2 (COX-2)
inhibitor meloxicam, and the non-selective COX-1 and COX-2
inhibitors lornoxicam, sodium metamizole, and ketorolac. The
current literature data regarding such effects of these agents are
scarce.
Materials and methods: The study was carried out on NMRI mice
weighing 20-35 g, kept in a standard laboratory environment. The
study was approved by the Ethics Committee of the University of
Medicine and Pharmacy „Carol Davila”, Bucharest. The study agents
were injected intraperitoneally, 10 mL/kg body weight (bw) 1 hour
before the assessment of the locomotor activity by cage testing (n=10
mice/ group) and 2 hours before the forced swimming tests (n=15).
The study agents were dissolved in normal saline (meloxicam,
sodium metamizole), ethanol 11.8% v/v in normal saline (ketorolac),
or water (lornoxicam), respectively. Negative and positive control
agents were also given (amitryptilline in the forced swimming test).
The cage floor used in the locomotor activity assessment was divided
into 20 equal 10 cm squares. The forced swimming test involved
partial immersion of the mice in cylinders (15/9cm height/diameter)
filled with water (10 cm depth at 28C), where they were left for 6
minutes. The cage endpoint used in the locomotor activity assessment
was the number of treaded squares. Four endpoints were used in the
forced swimming test (immobility latency for the entire 6 minutes,
and immobility, swimming, and climbing scores for the final 4
minutes of the swimming session), recorded by an observer that was
„blinded” to the experimental design. The statistical analysis used the
Levene test for variance homogeneity, ANOVA and post-hoc
analysis as appropriate, Tukey or Tamhane tests.
Results: No statistically significant increase or decrease in the
number of treaded squares was seen in the locomotor activity
assessment of any mice group. In the forced swimming test,
amitryptilline showed an antidepressant effect in each experiment, at
the 10 mg/kg bw dosage. Sodium metamizole was depressant at 100
mg/kg bw (increased the immobility score, p=0.049, Tamhane test),
but not in lower dosages as well (25 and 50 mg/kg bw). Ketorolac
showed an antidepressant effect at the intermediate dosage of 5
mg/kg bw, but not so in the dosages of 2.5 and 10 mg/kg bw,
respectively (increased the swimming score, p=0.012, Tamhane test).
Meloxicam and lornoxicam did not alter the forced swimming
endpoints at any dosage level.
Discussion: 1) Certain NSAIDs caused changes in the forced
swimming patterns without interfering with locomotion. 2) Sodium
metamizole showed a depressant effect, whereas ketorolac proved
antidepressant. Conclusion: NSAID-induced mood changes are not
class effects of these agents and apparently are independent of the
type of inhibited cyclooxygenase (COX-1 or COX-2).
Disclosure: This paper was co-financed from the European Social
Fund, through the Sectorial Operational Programme Human Resources Development 2007-2013, project number POSDRU /159
/1.5 /S /138907 "Excellence in scientific interdisciplinary research,
doctoral and postdoctoral, in the economic, social and medical fields
-EXCELIS", coordinator The Bucharest University of Economic
Studies.
Abstract: The aim of this exploratory research is to understand
further how organisations can evaluate their activities, which
generate knowledge creation, to meet changing stakeholder
expectations. A Scale of Knowledge (SoK) Framework is proposed
which links knowledge management and organisational activities to
changing stakeholder expectations. The framework was informed by
the knowledge management literature, as well as empirical work
conducted via a single case study of a multi-site hospital organisation
in Saudi Arabia. Eight in-depth semi-structured interviews were
conducted with managers from across the organisation regarding
current and future stakeholder expectations, organisational
strategy/activities and knowledge management. Data were analysed
using thematic analysis and a hierarchical value map technique to
identify activities that can produce further knowledge and
consequently impact on how stakeholder expectations are met.
The SoK Framework developed may be useful to practitioners as
an analytical aid to determine if current organisational activities
produce organisational knowledge which helps them meet
(increasingly higher levels of) stakeholder expectations. The
limitations of the research and avenues for future development of the
proposed framework are discussed.
Abstract: The objective of present research paper is to highlight
the importance of measuring advertisement effectiveness in print
media and to develop a conceptual model for advertisement
effectiveness. The developed model is based on dimensions on which
advertisement effectiveness depends and on the dimensions which are
used to measure the effectiveness. An in-depth and extensive
literature review is carried out to understand the concept of
advertisement effectiveness and its various determinants in context of
print media. Based on the insights gained, a conceptual framework
for advertisement effectiveness is presented. The model is an attempt
to uncover the relatively less explored area of advertisement
effectiveness in Indian advertising scenario. It is believed that present
work will encourage scholars and academicians to further explore the
area and will offer conceptual assistance and a fresh direction in the
domain of advertisement effectiveness.
Abstract: In this study, ultrasonic assisted machining (UAM) technique is applied in side-surface milling experiment for glass-ceramic workpiece material. The tungsten carbide cutting-tool with diamond coating is used in conjunction with two kinds of cooling/lubrication mediums such as water-soluble (WS) cutting fluid and minimum quantity lubricant (MQL). Full factorial process parameter combinations on the milling experiments are planned to investigate the effect of process parameters on cutting performance. From the experimental results, it tries to search for the better process parameter combination which the edge-indentation and the surface roughness are acceptable. In the machining experiments, ultrasonic oscillator was used to excite a cutting-tool along the radial direction producing a very small amplitude of vibration frequency of 20KHz to assist the machining process. After processing, toolmaker microscope was used to detect the side-surface morphology, edge-indentation and cutting tool wear under different combination of cutting parameters, and analysis and discussion were also conducted for experimental results. The results show that the main leading parameters to edge-indentation of glass ceramic are cutting depth and feed rate. In order to reduce edge-indentation, it needs to use lower cutting depth and feed rate. Water-soluble cutting fluid provides a better cooling effect in the primary cutting area; it may effectively reduce the edge-indentation and improve the surface morphology of the glass ceramic. The use of ultrasonic assisted technique can effectively enhance the surface finish cleanness and reduce cutting tool wear and edge-indentation.
Abstract: The distribution of a single global clock across a chip
has become the major design bottleneck for high performance VLSI
systems owing to the power dissipation, process variability and multicycle
cross-chip signaling. A Network-on-Chip (NoC) architecture
partitioned into several synchronous blocks has become a promising
approach for attaining fine-grain power management at the system
level. In a NoC architecture the communication between the blocks is
handled asynchronously. To interface these blocks on a chip
operating at different frequencies, an asynchronous FIFO interface is
inevitable. However, these asynchronous FIFOs are not required if
adjacent blocks belong to the same clock domain. In this paper, we
have designed and analyzed a 16-bit asynchronous micropipelined
FIFO of depth four, with the awareness of place and route on an
FPGA device. We have used a commercially available Spartan 3
device and designed a high speed implementation of the
asynchronous 4-phase micropipeline. The asynchronous FIFO
implemented on the FPGA device shows 76 Mb/s throughput and a
handshake cycle of 109 ns for write and 101.3 ns for read at the
simulation under the worst case operating conditions (voltage =
0.95V) on a working chip at the room temperature.
Abstract: This paper presents a study the effect of nose radius
(Rz-mm) on cutting force components and temperatures during the
machining simulation in an orthogonal cutting process for titanium
alloy (Ti-6Al-4V). The cutting process was performed at various
nose radiuses (Rz-mm) while the depth of cut (d-mm), feed rate (fmm/
tooth) and cutting speed (vc-m/ min) were remained constant.
The main cutting force (Fc), feed cutting force (Ft) and temperatures
were estimated by using finite element modeling (FEM) through
ABAQUS/EXPLICIT software and the simulation was developed the
two-dimension via an orthogonal cutting process during machining
titanium alloy (Ti-6Al-4V). The results led to the conclusion that the
nose radius (Rz-mm) has affected directly on the cutting force
components. However, temperature gave no indication or has no
significant relation with nose radius during machining titanium alloy
(Ti-6Al-4V). Hence, any increase or decrease in the nose radius (Rzmm)
during machining operation led to effect on the cutting forces
and thus it will be effective on surface finish, quality, and quantity of
products.
Abstract: This article presents modeling studies of NiAl alloy
under solid-particle erosion and liquid-drop erosion. In the
solid-particle erosion simulation, attention is paid to the oxide scale
thickness variation on the alloy in high-temperature erosion
environments. The erosion damage is assumed to be deformation wear
and cutting wear mechanisms, incorporating the influence of the oxide
scale on the eroded surface; thus the instantaneous oxide thickness is
the result of synergetic effect of erosion and oxidation. For liquid-drop
erosion, special interest is in investigating the effects of drop velocity
and drop size on the damage of the target surface. The models of
impact stress wave, mean depth of penetration, and maximum depth of
erosion rate (Max DER) are employed to develop various maps for
NiAl alloy, including target thickness vs. drop size (diameter), rate of
mean depth of penetration (MDRP) vs. drop impact velocity, and
damage threshold velocity (DTV) vs. drop size.
Abstract: This paper describes the issues relating to the role of
the flash flood early warning system provided by the Malaysian
Government to the communities in Malaysia, specifically during the
flash flood disaster in the Cameron Highlands, Malaysia. Normally,
flash flood disasters can occur as a result of heavy rainfall in an area,
and that water may possibly cause flooding via streams or narrow
channels. The focus of this study is the flash flood disaster which
occurred on 23 October 2013 in the Cameron Highlands, and as a
result the Sungai Bertam overflowed after the release of water from
the Sultan Abu Bakar Dam. This release of water from the dam
caused flash flooding which led to damage to properties and also the
death of residents and livestock in the area. Therefore, the effort of
this study is to identify the perceptions of the flash flood victims on
the role of the flash flood early warning system. For the purposes of
this study, data were gathered through face-to-face interviews from
those flood victims who were willing to participate in this study. This
approach helped the researcher to glean in-depth information about
their feelings and perceptions of the role of the flash flood early
warning system offered by the government. The data were analysed
descriptively and the findings show that the respondents of 22 flood
victims believe strongly that the flash flood early warning system was
confusing and dysfunctional, and communities had failed to response
positively to it. Therefore, most of the communities were not well
prepared for the releasing of water from the dam which caused
property damage, and 3 people were killed in the Cameron Highland
flash flood disaster.
Abstract: Machining of hard materials is a recent technology for
direct production of work-pieces. The primary challenge in
machining these materials is selection of cutting tool inserts which
facilitates an extended tool life and high-precision machining of the
component. These materials are widely for making precision parts for
the aerospace industry. Nickel-based alloys are typically used in
extreme environment applications where a combination of strength,
corrosion resistance and oxidation resistance material characteristics
are required. The present paper reports the theoretical and
experimental investigations carried out to understand the influence of
machining parameters on the response parameters. Considering the
basic machining parameters (speed, feed and depth of cut) a study has
been conducted to observe their influence on material removal rate,
surface roughness, cutting forces and corresponding tool wear.
Experiments are designed and conducted with the help of Central
Composite Rotatable Design technique. The results reveals that for a
given range of process parameters, material removal rate is favorable
for higher depths of cut and low feed rate for cutting forces. Low feed
rates and high values of rotational speeds are suitable for better finish
and higher tool life.
Abstract: This study aimed to examine the management and
development of forest tourism Kamchanoad. Ban Dung, Udon Thani
sustainability. Data were collected by means of qualitative research
including in-depth interviews, semi- structured, and then the data
were summarized and discussed in accordance with the objectives.
And make a presentation in the form of lectures. The target
population for the study consisted of 16 people, including
representatives from government agencies, community leaders and
the community. The results showed that Guidelines for the
Management and Development of Forest Tourism Kamchanoad
include management of buildings and infrastructure such as roads,
water, electricity, toilets. Other developments are the establishment
of a service center that provides information and resources to
facilitate tourists.; nature trails and informative signage to educate
visitors on the path to the jungle Kamchanoad; forest activities for
tourists who are interested only in occasional educational activities
such as vegetation, etc.; disseminating information on various aspects
of tourism through various channels in both Thailand and English, as
well as a web site to encourage community involvement in the
planning and management of tourism together with the care and
preservation of natural resources and preserving the local cultural
tourist area of Kamchanoad.
Abstract: Over the past four decades, the fatigue behavior of
nickel-based alloys has been widely studied. However, in recent
years, significant advances in the fabrication process leading to grain
size reduction have been made in order to improve fatigue properties
of aircraft turbine discs. Indeed, a change in particle size affects the
initiation mode of fatigue cracks as well as the fatigue life of the
material. The present study aims to investigate the fatigue behavior of
a newly developed nickel-based superalloy under biaxial-planar
loading. Low Cycle Fatigue (LCF) tests are performed at different
stress ratios so as to study the influence of the multiaxial stress state
on the fatigue life of the material. Full-field displacement and strain
measurements as well as crack initiation detection are obtained using
Digital Image Correlation (DIC) techniques. The aim of this
presentation is first to provide an in-depth description of both the
experimental set-up and protocol: the multiaxial testing machine, the
specific design of the cruciform specimen and performances of the
DIC code are introduced. Second, results for sixteen specimens
related to different load ratios are presented. Crack detection, strain
amplitude and number of cycles to crack initiation vs. triaxial stress
ratio for each loading case are given. Third, from fractographic
investigations by scanning electron microscopy it is found that the
mechanism of fatigue crack initiation does not depend on the triaxial
stress ratio and that most fatigue cracks initiate from subsurface
carbides.
Abstract: In this study, several crossplots of the P-impedance
with the lithology logs (gamma ray, neutron porosity, deep resistivity,
water saturation and Vp/Vs curves) were made in three available
wells, which were drilled in central part of the Blue Nile basin in
depths varies from 1460m to 1600m. These crossplots were
successful to discriminate between sand and shale when using PImpedance
values, and between the wet sand and the pay sand when
using both P-impedance and Vp/Vs together. Also some impedance
sections were converted to porosity sections using linear formula to
characterize the reservoir in terms of porosity. The used crossplots
were created on log resolution, while the seismic resolution can
identify only the reservoir, unless a 3D seismic angle stacks were
available; then it would be easier to identify the pay sand with great
confidence; through high resolution seismic inversion and
geostatistical approach when using P-impedance and Vp/Vs volumes.
Abstract: Natural hydrocarbon seepage has helped petroleum
exploration as a direct indicator of gas and/or oil subsurface
accumulations. Surface macro-seeps are generally an indication of a
fault in an active Petroleum Seepage System belonging to a Total
Petroleum System. This paper describes a case study in which
multiple analytical techniques were used to identify and characterize
trace petroleum-related hydrocarbons and other volatile organic
compounds in groundwater samples collected from Sousse aquifer
(Central Tunisia). The analytical techniques used for analyses of
water samples included gas chromatography-mass spectrometry (GCMS),
capillary GC with flame-ionization detection, Compound
Specific Isotope Analysis, Rock Eval Pyrolysis. The objective of the
study was to confirm the presence of gasoline and other petroleum
products or other volatile organic pollutants in those samples in order
to assess the respective implication of each of the potentially
responsible parties to the contamination of the aquifer. In addition,
the degree of contamination at different depths in the aquifer was also
of interest. The oil and gas seeps have been investigated using
biomarker and stable carbon isotope analyses to perform oil-oil and
oil-source rock correlations. The seepage gases are characterized by
high CH4 content, very low δ13CCH4 values (-71,9 ‰) and high
C1/C1–5 ratios (0.95–1.0), light deuterium–hydrogen isotope ratios (-
198 ‰) and light δ13CC2 and δ13CCO2 values (-23,8‰ and-23,8‰
respectively) indicating a thermogenic origin with the contribution of
the biogenic gas. An organic geochemistry study was carried out on
the more ten oil seep samples. This study includes light hydrocarbon
and biomarkers analyses (hopanes, steranes, n-alkanes, acyclic
isoprenoids, and aromatic steroids) using GC and GC-MS. The
studied samples show at least two distinct families, suggesting two
different types of crude oil origins: the first oil seeps appears to be
highly mature, showing evidence of chemical and/or biological
degradation and was derived from a clay-rich source rock deposited
in suboxic conditions. It has been sourced mainly by the lower
Fahdene (Albian) source rocks. The second oil seeps was derived
from a carbonate-rich source rock deposited in anoxic conditions,
well correlated with the Bahloul (Cenomanian-Turonian) source rock.
Abstract: The present work analyses different parameters of end
milling to minimize the surface roughness for AISI D2 steel. D2 Steel
is generally used for stamping or forming dies, punches, forming
rolls, knives, slitters, shear blades, tools, scrap choppers, tyre
shredders etc. Surface roughness is one of the main indices that
determines the quality of machined products and is influenced by
various cutting parameters. In machining operations, achieving
desired surface quality by optimization of machining parameters, is a
challenging job. In case of mating components the surface roughness
become more essential and is influenced by the cutting parameters,
because, these quality structures are highly correlated and are
expected to be influenced directly or indirectly by the direct effect of
process parameters or their interactive effects (i.e. on process
environment). In this work, the effects of selected process parameters
on surface roughness and subsequent setting of parameters with the
levels have been accomplished by Taguchi’s parameter design
approach. The experiments have been performed as per the
combination of levels of different process parameters suggested by
L9 orthogonal array. Experimental investigation of the end milling of
AISI D2 steel with carbide tool by varying feed, speed and depth of
cut and the surface roughness has been measured using surface
roughness tester. Analyses of variance have been performed for mean
and signal-to-noise ratio to estimate the contribution of the different
process parameters on the process.