Abstract: Al2(HPO4)3 was easily prepared and used as a solid
acid in acetalization of carbonyl compounds at room temperature and
under solvent-free conditions. The protection was done in short
reaction times and in good to high isolated yields. The cheapness and
availability of this reagent with easy procedure and work-up make
this method attractive for the organic synthesis.
Abstract: The discharge of dye in industrial effluents is of great concern because their presence and accumulation have a toxic or carcinogenic effect on living species. The removal of such compounds at such low levels is a difficult problem. The adsorption process is an effective and attractive proposition for the treatment of dye contaminated wastewater. Activated carbon adsorption in fixed beds is a very common technology in the treatment of water and especially in processes of decolouration. However, it is expensive and the powdered one is difficult to be separated from aquatic system when it becomes exhausted or the effluent reaches the maximum allowable discharge level. The regeneration of exhausted activated carbon by chemical and thermal procedure is also expensive and results in loss of the sorbent. The focus of this research was to evaluate the adsorption potential of the raw clay in removing rhodamine B from aqueous solutions using a laboratory fixed-bed column. The continuous sorption process was conducted in this study in order to simulate industrial conditions. The effect of process parameters, such as inlet flow rate, adsorbent bed height, and initial adsorbate concentration on the shape of breakthrough curves was investigated. A glass column with an internal diameter of 1.5 cm and height of 30 cm was used as a fixed-bed column. The pH of feed solution was set at 8.5. Experiments were carried out at different bed heights (5 - 20 cm), influent flow rates (1.6- 8 mL/min) and influent rhodamine B concentrations (20 - 80 mg/L). The obtained results showed that the adsorption capacity increases with the bed depth and the initial concentration and it decreases at higher flow rate. The column regeneration was possible for four adsorption–desorption cycles. The clay column study states the value of the excellent adsorption capacity for the removal of rhodamine B from aqueous solution. Uptake of rhodamine B through a fixed-bed column was dependent on the bed depth, influent rhodamine B concentration, and flow rate.
Abstract: Municipal Solid Waste (MSW) disposed in landfill sites decompose under anaerobic conditions and produce gases which mainly contain carbon dioxide (CO2) and methane (CH4). Methane has the potential of causing global warming 25 times more than CO2, and can potentially affect human life and environment. Thus, this research aims to determine MSW generation and the annual CH4 emissions from the generated waste in Oman over the years 1971-2030. The estimation of total waste generation was performed using existing models, while the CH4 emissions estimation was performed using the intergovernmental panel on climate change (IPCC) default method. It is found that total MSW generation in Oman might be reached 3,089 Gg in the year 2030, which approximately produced 85 Gg of CH4 emissions in the year 2030.
Abstract: This study attempts to consider the linkage between management and computer sciences in order to develop the software named “IntelSymb” as a demo application to prove data analysis of non-energy* fields’ diversification, which will positively influence on energy dependency mitigation of countries. Afterward, we analyzed 18 years of economic fields of development (5 sectors) of 13 countries by identifying which patterns mostly prevailed and which can be dominant in the near future. To make our analysis solid and plausible, as a future work, we suggest developing a gateway or interface, which will be connected to all available on-line data bases (WB, UN, OECD, U.S. EIA) for countries’ analysis by fields. Sample data consists of energy (TPES and energy import indicators) and non-energy industries’ (Main Science and Technology Indicator, Internet user index, and Sales and Production indicators) statistics from 13 OECD countries over 18 years (1995-2012). Our results show that the diversification of non-energy industries can have a positive effect on energy sector dependency (energy consumption and import dependence on crude oil) deceleration. These results can provide empirical and practical support for energy and non-energy industries diversification’ policies, such as the promoting of Information and Communication Technologies (ICTs), services and innovative technologies efficiency and management, in other OECD and non-OECD member states with similar energy utilization patterns and policies. Industries, including the ICT sector, generate around 4 percent of total GHG, but this is much higher — around 14 percent — if indirect energy use is included. The ICT sector itself (excluding the broadcasting sector) contributes approximately 2 percent of global GHG emissions, at just under 1 gigatonne of carbon dioxide equivalent (GtCO2eq). Ergo, this can be a good example and lesson for countries which are dependent and independent on energy, and mainly emerging oil-based economies, as well as to motivate non-energy industries diversification in order to be ready to energy crisis and to be able to face any economic crisis as well.
Abstract: Optimisation of the physical and mechanical properties of cold rolled thin strips is achieved by controlling the rolling parameters. In this paper, the factors affecting the asymmetrical cold rolling of thin low carbon steel strip have been studied at a speed ratio of 1.1 without lubricant applied. The effect of rolling parameters on the resulting microstructure was also investigated. It was found that under dry condition, work roll shifting and work roll cross angle can improve the strip profile, and the result is more significant with an increase of work roll cross angle rather than that of work roll shifting. However, there was no obvious change in microstructure. In addition, effects of rolling parameters on strip profile and microstructure have also been discussed.
Abstract: Measurement of the ultrasonic pulse velocity (UPV) is an important tool in diagnostic examination of concrete. In this method piezoelectric transducers are normally held in direct contact with the concrete surface. The current study aims to test the hypothesis that a preferential coupling effect might exist i.e. that the speed of sound measured depends on the couplant used. In this study, different coupling media of varying acoustic impedance were placed between the transducers and concrete samples made with constant aggregate content but with different compressive strengths. The preliminary results show that using coupling materials (both solid and a range of liquid substances) has an effect on the pulse velocity measured in a given concrete. The effect varies depending on the material used. The UPV measurements with solid coupling were higher than these from the liquid coupling at all strength levels. The tests using couplants generally recorded lower UPV values than the conventional test, except when carbon fiber composite was used, which retuned higher values. Analysis of variances (ANOVA) was performed to confirm that there are statistically significant differences between the measurements recorded using a conventional system and a coupled system.
Abstract: Following plants-barley (Hordeum sativum), alfalfa
(Medicago sativa), grass mixture (red fescue-75%, long-term
ryegrass - 20% Kentucky bluegrass - 10%), oilseed rape (Brassica
napus biennis), resistant to growth in the contaminated soil with oil
content of 15.8 g / kg 25.9 g / kg soil were used. Analysis of the
population showed that the oil pollution reduces the number of
bacteria in the rhizosphere and rhizoplane of plants and enhances the
amount of spore-forming bacteria and saprotrophic micromycetes. It
was shown that regardless of the plant, dominance of Pseudomonas
and Bacillus genera bacteria was typical for the rhizosphere and
rhizoplane of plants. The frequency of bacteria of these genera was
more than 60%. Oil pollution changes the ratio of occurrence of
various types of bacteria in the rhizosphere and rhizoplane of plants.
Besides the Pseudomonas and Bacillus genera, in the presence of
hydrocarbons in the root zone of plants dominant and most typical
were the representatives of the Mycobacterium and Rhodococcus
genera. Together the number was between 62% to 72%.
Abstract: Since the advent of the law 86/14 concerning the
exploitation of the national territory by foreign companies in
partnership with the Algerian oil and gas company, the problem of
hydrocarbons metering in the sharing production come out.
More generally, good management counting hydrocarbons can
provide data on the production wells, the field and the reservoir for
medium and long term planning, particularly in the context of the
management and field development.
In this work, we are interested in the transactional metering which
is a very delicate and crucial period in the current context of the new
hydrocarbon’s law characterized by assets system between the
various activities of Sonatrach and its foreign partners.
After a state of the art on hydrocarbons metering devices in
Algeria and elsewhere, we will decline the advantages and
disadvantages of each system, and then we describe the problem to
try to reach an optimal solution.
Abstract: Problem of food preservation is extremely important
for mankind. Viscous damage ("illness") of bread results from
development of Bacillus spp. bacteria. High temperature resistant
spores of this microorganism are steady against 120°C) and remain in
bread during pastries, potentially causing spoilage of the final
product. Scientists are interested in further characterization of bread
spoiling Bacillus spp. species. Our aim was to find weather yeast
Saccharomyces cerevisiae strains that are able to produce natural
antimicrobial killer factor can preserve bread illness. By diffusion
method, we showed yeast antagonistic activity against spore-forming
bacteria. Experimental technological parameters were the same as for
bakers' yeasts production on the industrial scale. Risograph test
during dough fermentation demonstrated gas production. The major
finding of the study was a clear indication of the presence of killer
yeast strain antagonistic activity against rope in bread causing
bacteria. After demonstrating antagonistic effect of S. cerevisiae on
bacteria using solid nutrient medium, we tested baked bread under
provocative conditions. We also measured formation of carbon
dioxide in the dough, dough-making duration and quality of the final
products, when using different strains of S. cerevisiae. It is
determined that the use of yeast S. cerevisiae RCAM 01730 killer
strain inhibits appearance of rope in bread. Thus, natural yeast
antimicrobial killer toxin, produced by some S. cerevisiae strains is
an anti-rope in bread protector.
Abstract: The combination of the properties of graphene oxide
(OG) and PVDF homopolymer makes their combined composite
materials as multifunctional systems with great potential. Knowledge
of the molecular structure is essential for better use. In this work, the
degradation of PVDF polymer exposed to gamma irradiation in
oxygen atmosphere in high dose rate has been studied and compared
to degradation of PVDF/OG composites. The samples were irradiated
with a Co-60 source at constant dose rate, with doses ranging from
100 kGy to 1,000 kGy. In FTIR data shown that the formation of
oxidation products was at the both samples with formation of
carbonyl and hydroxyl groups amongst the most prevalent products
in the pure PVDF samples. In the other hand, the composites samples
exhibit less presence of degradation products with predominant
formation of carbonyl groups, these results also seen in the UV-Vis
analysis. The results show that the samples of composites may have
greater resistance to the irradiation process, since they have less
degradation products than pure PVDF samples seen by spectroscopic
techniques.
Abstract: The layered structure LiNi1/3Co1/3Mn1/3-xAlxO2 (x = 0 ~
0.04) series cathode materials were synthesized by a carbonate
co-precipitation method, followed by a high temperature calcination
process. The influence of Al substitution on the microstructure and
electrochemical performances of the prepared materials was
investigated by X-Ray diffraction (XRD), scanning electron
microscopy (SEM), and galvanostatic charge/discharge test. The
results show that the LiNi1/3Co1/3Mn1/3-xAlxO2 has a well-ordered
hexagonal α-NaFeO2 structure. Although the discharge capacity of
Al-doped samples decreases as x increases,
LiNi1/3Co1/3Mn1/3-0.02Al0.02O2 exhibits superior capacity retention at
high voltage (4.6 V). Therefore, LiNi1/3Co1/3Mn1/3-0.02Al0.02O2 is a
promising material for “green” vehicles.
Abstract: The combination of multi–walled carbon nanotubes
(MWCNTs) with polymers offers an attractive route to reinforce the
macromolecular compounds as well as the introduction of new
properties based on morphological modifications or electronic
interactions between the two constituents. As they are only a few
nanometers in dimension, it offers ultra-large interfacial area per
volume between the nano-element and polymer matrix. Nevertheless,
the use of MWCNTs as a rough material in different applications has
been largely limited by their poor processability, insolubility, and
infusibility. Studies concerning the nanofiller reinforced polymer
composites are justified in an attempt to overcome these limitations.
This work presents one preliminary study of MWCNTs dispersion
into the PVDF homopolymer. For preparation, the composite
components were diluted in n,n-dimethylacetamide (DMAc) with
mechanical agitation assistance. After complete dilution, followed by
slow evaporation of the solvent at 60°C, the samples were dried.
Films of about 80 μm were obtained. FTIR and UV-Vis
spectroscopic techniques were used to characterize the
nanocomposites. The appearance of absorption bands in the FTIR
spectra of nanofilled samples, when compared to the spectrum of
pristine PVDF samples, are discussed and compared with the UV-Vis
measurements.
Abstract: A composite material with carbon fiber and polymer
matrix has been used as adherent for manufacturing adhesive joints.
In order to evaluate different fiber orientations on joint performance,
the adherents with the 0°, ±15°, ±30°, ±45° fiber orientations were
used in the single lap joint configuration. The joints with an overlap
length of 25 mm were prepared according to the ASTM 1002
specifications and subjected to tensile loadings. The structural
adhesive used was a two-part epoxy to be cured at 70°C for an hour.
First, mechanical behaviors of the adherents were measured using
three point bending test. In the test, considerations were given to
stress to failure and elastic modulus. The results were compared with
theoretical ones using rule of mixture. Then, the joints were
manufactured in a specially prepared jig, after a proper surface
preparation. Experimental results showed that the fiber orientations
of the adherents affected the joint performance considerably; the
joints with ±45° adherents experienced the worst shear strength, half
of those with 0° adherents, and in general, there was a great
relationship between the fiber orientations and failure mechanisms.
Delamination problems were observed for many joints, which were
thought to be due to peel effects at the ends of the overlap. It was
proved that the surface preparation applied to the adherent surface
was adequate. For further explanation of the results, a numerical
work should be carried out using a possible non-linear analysis.
Abstract: This paper investigates the application of metallic
coatings on high fiber volume fraction carbon/epoxy polymer matrix
composites. For the grip of the metallic layer, a method of modifying
the surface of the composite by introducing a mixture of copper and
steel powder (filler powders) which can reduce the impact of thermal
spray particles. The powder was introduced to the surface at the time
of the forming. Arc spray was used to project the zinc coating layer.
The substrate was grit blasted to avoid poor adherence. The porosity, microstructure, and morphology of layers are
characterized by optical microscopy, SEM and image analysis. The
samples were studied also in terms of hardness and erosion resistance.
This investigation did not reveal any visible evidence damage to the
substrates. The hardness of zinc layer was about 25.94 MPa and the
porosity was around (∼6.70%). The erosion test showed that the zinc
coating improves the resistance to erosion. Based on the results
obtained, we can conclude that thermal spraying allows the production
of protective coating on PMC. Zinc coating has been identified as a
compatible material with the substrate. The filler powders layer
protects the substrate from the impact of hot particles and allows
avoiding the rupture of brittle carbon fibers.
Abstract: The beginning of 21st century has witnessed new
advancements in the design and use of new materials for biosensing
applications, from nano to macro, protein to tissue. Traditional
analytical methods lack a complete toolset to describe the
complexities introduced by living systems, pathological relations,
discrete hierarchical materials, cross-phase interactions, and
structure-property dependencies. Materiomics – via systematic
molecular dynamics (MD) simulation – can provide structureprocess-
property relations by using a materials science approach
linking mechanisms across scales and enables oriented biosensor
design. With this approach, DNA biosensors can be utilized to detect
disease biomarkers present in individuals’ breath such as acetone for
diabetes. Our wireless sensor array based on single-stranded DNA
(ssDNA)-decorated single-walled carbon nanotubes (SWNT) has
successfully detected trace amount of various chemicals in vapor
differentiated by pattern recognition. Here, we present how MD
simulation can revolutionize the way of design and screening of DNA
aptamers for targeting biomarkers related to oral diseases and oral
health monitoring. It demonstrates great potential to be utilized to
build a library of DNDA sequences for reliable detection of several
biomarkers of one specific disease, and as well provides a new
methodology of creating, designing, and applying of biosensors.
Abstract: A combined heat and power (CHP) system is an efficient and clean way to generate power (electricity). Heat produced by the CHP system can be used for water and space heating. The CHP system which uses hydrogen as fuel produces zero carbon emission. Its’ efficiency can reach more than 80% whereas that of a traditional power station can only reach up to 50% because much of the thermal energy is wasted. The other advantages of CHP systems include that they can decentralize energy generation, improve energy security and sustainability, and significantly reduce the energy cost to the users. This paper presents the economic benefits of using a CHP system in the domestic environment. For this analysis, natural gas is considered as potential fuel as the hydrogen fuel cell based CHP systems are rarely used. UK government incentives for CHP systems are also considered as the added benefit. Results show that CHP requires a significant initial investment in returns it can reduce the annual energy bill significantly. Results show that an investment may be paid back in 7 years. After the back period, CHP can run for about 3 years as most of the CHP manufacturers provide 10 year warranty.
Abstract: Nanofibers are defined as fibers with diameters less
than 100 nanometers. In this study, behaviours of activated carbon
nanofiber (ACNF), carbon nanofiber (CNF), polyacrylonitrile/ carbon
nanotube (PAN/CNT), polyvinyl alcohol/nanosilver (PVA/Ag) in
proton exchange membrane (PEM) fuel cells are investigated
experimentally. This material was used as gas diffusion layer (GDL)
in PEM fuel cells. In this study, the electrical conductivities of
nanofiber and nanofiber/nanoparticles have been studied to
understand their effects on PEM fuel cell performance. According to
the experimental results, the maximum electrical conductivity
performance of the fuel cell with nanofiber was found to be at
PVA/Ag (at UConn condition). The electrical conductivities of CNF,
ACNF, PAN/CNT are lower for PEM. The resistance of cell with
PVA/Ag is lower than the resistance of cell with PAN/CNT, ACNF,
CNF.
Abstract: Biodiesel is widely investigated to solve the twin
problem of depletion of fossil fuel and environmental degradation.
The main objective of the present work is to compare performance,
emissions, and combustion characteristics of biodiesel derived from
cotton seed oil in a diesel engine with the baseline results of
petrodiesel fuel. Tests have been conducted on a single cylinder, four
stroke CIDI diesel engine with a speed of 1500 rpm and a fixed
compression ratio of 17.5 at different load conditions. The
performance parameters evaluated include brake thermal efficiency,
brake specific fuel consumption, brake power, indicated mean
effective pressure, mechanical efficiency, and exhaust gas
temperature. Regarding combustion study, cylinder pressure, rate of
pressure rise, net heat release rate, cumulative heat release, mean gas
temperature, mass fraction burned, and fuel line pressure were
evaluated. The emission parameters such as carbon monoxide, carbon
dioxide, un-burnt hydrocarbon, oxides of nitrogen, and smoke
opacity were also measured by a smoke meter and an exhaust gas
analyzer and compared with baseline results. The brake thermal
efficiency of cotton seed oil methyl ester (CSOME) was lower than
that of petrodiesel and brake specific fuel consumption was found to
be higher. However, biodiesel resulted in the reduction of carbon
dioxide, un-burnt hydrocarbon, and smoke opacity at the expense of
nitrogen oxides. Carbon monoxide emissions for biodiesel was higher
at maximum output power. It has been found that the combustion
characteristics of cotton seed oil methyl ester closely followed those
of standard petrodiesel. The experimental results suggested that
biodiesel derived from cotton seed oil could be used as a good
substitute to petrodiesel fuel in a conventional diesel without any
modification.
Abstract: Carbon dioxide is one of the major greenhouse gas
(GHG) contributors. It is an obligation of the industry to reduce the
amount of carbon dioxide emission to the acceptable limits.
Tremendous research and studies are reported in the past and still the
quest to find the suitable and economical solution of this problem
needed to be explored in order to develop the most plausible absorber
for carbon dioxide removal. Amino acids can be potential alternate
solvents for carbon dioxide capture from gaseous streams. This is due
to its ability to resist oxidative degradation, low volatility and its
ionic structure. In addition, the introduction of promoter-like
piperazine to amino acid helps to further enhance the solubility. In
this work, the effect of piperazine on thermo physical properties and
solubility of β-Alanine aqueous solutions were studied for various
concentrations. The measured physicochemical properties data was
correlated as a function of temperature using least-squares method
and the correlation parameters are reported together with it respective
standard deviations. The effect of activator piperazine on the CO2
loading performance of selected amino acid under high-pressure
conditions (1bar to 10bar) at temperature range of (30 to 60)oC was
also studied. Solubility of CO2 decreases with increasing temperature
and increases with increasing pressure. Quadratic representation of
solubility using Response Surface Methodology (RSM) shows that
the most important parameter to optimize solubility is system
pressure. The addition of promoter increases the solubility effect of
the solvent.
Abstract: Inspired by the Formula-1 competition, IMechE
(Institute of Mechanical Engineers) and Formula SAE (Society of
Mechanical Engineers) organize annual competitions for University
and College students worldwide to compete with a single-seat racecar
they have designed and built. Design of the chassis or the frame is a
key component of the competition because the weight and stiffness
properties are directly related with the performance of the car and the
safety of the driver. In addition, a reduced weight of the chassis has
direct influence on the design of other components in the car. Among
others, it improves the power to weight ratio and the aerodynamic
performance. As the power output of the engine or the battery
installed in the car is limited to 80 kW, increasing the power to
weight ratio demands reduction of the weight of the chassis, which
represents the major part of the weight of the car. In order to reduce
the weight of the car, ION Racing team from University of
Stavanger, Norway, opted for a monocoque design. To ensure
fulfilment of the competition requirements of the chassis, the
monocoque design should provide sufficient torsional stiffness and
absorb the impact energy in case of possible collision. The study reported in this article is based on the requirements for
Formula Student competition. As part of this study, diverse
mechanical tests were conducted to determine the mechanical
properties and performances of the monocoque design. Upon a
comprehensive theoretical study of the mechanical properties of
sandwich composite materials and the requirements of monocoque
design in the competition rules, diverse tests were conducted
including 3-point bending test, perimeter shear test and test for
absorbed energy. The test panels were homemade and prepared with
equivalent size of the side impact zone of the monocoque, i.e. 275
mm x 500 mm, so that the obtained results from the tests can be
representative. Different layups of the test panels with identical core
material and the same number of layers of carbon fibre were tested
and compared. Influence of the core material thickness was also
studied. Furthermore, analytical calculations and numerical analysis
were conducted to check compliance to the stated rules for Structural
Equivalency with steel grade SAE/AISI 1010. The test results were
also compared with calculated results with respect to bending and
torsional stiffness, energy absorption, buckling, etc. The obtained results demonstrate that the material composition
and strength of the composite material selected for the monocoque
design has equivalent structural properties as a welded frame and thus
comply with the competition requirements. The developed analytical
calculation algorithms and relations will be useful for future
monocoque designs with different lay-ups and compositions.