Abstract: This paper proposes a power-controlled scheduling scheme for devices using a directional antenna in smart home. In the case of the home network using directional antenna, devices can concurrently transmit data in the same frequency band. Accordingly, the throughput increases compared to that of devices using omni-directional antenna in proportional to the number of concurrent transmissions. Also, the number of concurrent transmissions depends on the beamwidth of antenna, the number of devices operating in the network , transmission power, interference and so on. In particular, the less transmission power is used, the more concurrent transmissions occur due to small transmission range. In this paper, we considered sub-optimal scheduling scheme for throughput maximization and power consumption minimization. In the scheme, each device is equipped with a directional antenna. Various beamwidths, path loss components, and antenna radiation efficiencies are considered. Numerical results show that the proposed schemes outperform the scheduling scheme using directional antennas without power control.
Abstract: This paper discusses a genetic algorithm (GA) based optimal load shedding that can apply for electrical distribution networks with and without dispersed generators (DG). Also, the proposed method has the ability for considering constant and variable capacity deficiency caused by unscheduled outages in the bulked generation and transmission system of bulked power supply. The genetic algorithm (GA) is employed to search for the optimal load shedding strategy in distribution networks considering DGs in two cases of constant and variable modelling of bulked power supply of distribution networks. Electrical power distribution systems have a radial network and unidirectional power flows. With the advent of dispersed generations, the electrical distribution system has a locally looped network and bidirectional power flows. Therefore, installed DG in the electrical distribution systems can cause operational problems and impact on existing operational schemes. Introduction of DGs in electrical distribution systems has introduced many new issues in operational and planning level. Load shedding as one of operational issue has no exempt. The objective is to minimize the sum of curtailed load and also system losses within the frame-work of system operational and security constraints. The proposed method is tested on a radial distribution system with 33 load points for more practical applications.
Abstract: A complete CAD procedure to model a twisted-bladed
vertical-axis wind turbine (VAWT) is presented with the aim of
determining some practical guidelines to be used for the generation
of an easily-meshable CAD geometry to be adopted as the basis of
both CFD and FEM numerical simulations.
Abstract: Malting is usually carried out on intact barley seed,
while hull is still attached to it. In this study, oat grain with and
without hull was subjected to controlled germination to optimize its
enzymes activity, in such a way that lipase has the lowest and α-
amylase and proteinase the highest activities. Since pH has a great
impact on the activity of the enzymes, the pH of germination media
was set up to 3 to 8. In dehulled oats, lipase and α-amylase had the
lowest and highest activities in pHs 3 and 6, respectively whereas the
highest proteinase activity was evidenced at pH 7 and 4 in the oats
with and without hull respectively. While measurements indicated
that the effect of hull on the enzyme activities particularly in lipase
and amylase at each level of the pH are significantly different, the
best results were obtained in those samples in which their hull had
been removed. However, since the similar lipase activity in
germinated dehulled oat were recorded at the pHs 4 and 5, therefore
it was concluded that pH 5 in dehulled oat seed may provide the
optimum enzyme activity for all the enzymes.
Abstract: Maize and Indian mustard are significant crops in
semi-arid climate zones of India. Improved water management
requires precise scheduling of irrigation, which in turn requires an
accurate computation of daily crop evapotranspiration (ETc). Daily
crop evapotranspiration comes as a product of reference
evapotranspiration (ET0) and the growth stage specific crop
coefficients modified for daily variation. The first objective of
present study is to develop crop coefficients Kc for Maize and Indian
mustard. The estimated values of Kc for maize at the four crop
growth stages (initial, development, mid-season, and late season) are
0.55, 1.08, 1.25, and 0.75, respectively, and for Indian mustard the Kc
values at the four growth stages are 0.3, 0.6, 1.12, and 0.35,
respectively. The second objective of the study is to compute daily
crop evapotranspiration from ET0 and crop coefficients. Average
daily ETc of maize varied from about 2.5 mm/d in the early growing
period to > 6.5 mm/d at mid season. The peak ETc of maize is 8.3
mm/d and it occurred 64 days after sowing at the reproductive growth
stage when leaf area index was 4.54. In the case of Indian mustard,
average ETc is 1 mm/d at the initial stage, >1.8 mm/d at mid season
and achieves a peak value of 2.12 mm/d on 56 days after sowing.
Improved schedules of irrigation have been simulated based on daily
crop evapo-transpiration and field measured data. Simulation shows a
close match between modeled and field moisture status prevalent
during crop season.
Abstract: Anaerobic treatment has many advantages over other
biological method particularly when used to treat complex
wastewater such as petroleum refinery wastewater. In this study two
Up-flow Anaerobic Sludge Blanket (UASB) reactors were operated
in parallel to treat six volumetric organic loads (0.58, 1.21, 0.89,
2.34, 1.47 and 4.14 kg COD/m3·d) to evaluate the chemical oxygen
demand (COD) removal efficiency. The reactors were continuously
adapting to the changing of operation condition with increase in the
removal efficiency or slight decrease until the last load which was
more than two times the load, at which the reactor stressed and the
removal efficiency decreased to 75% with effluent concentration of
1746 mg COD/L. Other parameters were also monitored such as pH,
alkalinity, volatile fatty acid and gas production rate. The UASB
reactor was suitable to treat petroleum refinery wastewater and the
highest COD removal rate was 83% at 1215 kg/m3·d with COD
concentration about 356 mg/L in the effluent.
Abstract: The forest stand consisted of four layers. The species
composition between the third and the bottom layers was almost
similar, whereas it was almost exclusive between the top and the lower
three layers. The values of Shannon-s index H' and Pielou-s index
J ' tended to increase from the bottom layer upward, except for
H' -value of the top layer. The values of H' and J ' were 4.21 bit
and 0.73, respectively, for the total stand. High woody species
diversity of the forest depended on large trees in the upper layers,
which trend was different from a subtropical evergreen broadleaf
forest grown in silicate habitat in the northern part of Okinawa Island.
The spatial distribution of trees was overlapped between the third and
the bottom layers, whereas it was independent or slightly exclusive
between the top and the lower three layers. Mean tree weight of each
layer decreased from the top toward the bottom layer, whereas the
corresponding tree density increased from the top downward. This
relationship was analogous to the process of self-thinning plant
populations.
Abstract: Dextran is a D-glucose polymer which is produced by
Leuconostoc mesenteroides grown in a sucrose-rich media. The
organism was obtained from the Persian Type Culture Collection
(PTCC) and was transferred in MRS broth medium at 30°C and pH
6.8 for 24 h. After preparation of inoculums, organisms were
inoculated into five liquid fermentation media containing either
molasses or cheese whey or different combinations of cheese whey
and molasses. After certain fermentation period, the produced
dextran was separated and dried. Dextran yield was calculated and
significant differences in different media were observed.
Furthermore, FT-IR analysis was performed and the results showed
that there were no significant differences in the produced dextran
structures.
Abstract: This paper proposes an innovative methodology for
Acceptance Sampling by Variables, which is a particular category of
Statistical Quality Control dealing with the assurance of products
quality. Our contribution lies in the exploitation of machine learning
techniques to address the complexity and remedy the drawbacks of
existing approaches. More specifically, the proposed methodology
exploits Artificial Neural Networks (ANNs) to aid decision making
about the acceptance or rejection of an inspected sample. For any
type of inspection, ANNs are trained by data from corresponding
tables of a standard-s sampling plan schemes. Once trained, ANNs
can give closed-form solutions for any acceptance quality level and
sample size, thus leading to an automation of the reading of the
sampling plan tables, without any need of compromise with the
values of the specific standard chosen each time. The proposed
methodology provides enough flexibility to quality control engineers
during the inspection of their samples, allowing the consideration of
specific needs, while it also reduces the time and the cost required for
these inspections. Its applicability and advantages are demonstrated
through two numerical examples.
Abstract: Recently, the findings on the MEG iterative scheme has demonstrated to accelerate the convergence rate in solving any system of linear equations generated by using approximation equations of boundary value problems. Based on the same scheme, the aim of this paper is to investigate the capability of a family of four-point block iterative methods with a weighted parameter, ω such as the 4 Point-EGSOR, 4 Point-EDGSOR, and 4 Point-MEGSOR in solving two-dimensional elliptic partial differential equations by using the second-order finite difference approximation. In fact, the formulation and implementation of three four-point block iterative methods are also presented. Finally, the experimental results show that the Four Point MEGSOR iterative scheme is superior as compared with the existing four point block schemes.
Abstract: Quantitative precipitation forecast (QPF) from
atmospheric model as input to hydrological model in an integrated
hydro-meteorological flood forecasting system has been operational
in many countries worldwide. High-resolution numerical weather
prediction (NWP) models with grid cell sizes between 2 and 14 km
have great potential in contributing towards reasonably accurate QPF.
In this study the potential of two NWP models to forecast
precipitation for a flood-prone area in a tropical region is examined.
The precipitation forecasts produced from the Fifth Generation Penn
State/NCAR Mesoscale (MM5) and Weather Research and
Forecasting (WRF) models are statistically verified with the observed
rain in Kelantan River Basin, Malaysia. The statistical verification
indicates that the models have performed quite satisfactorily for low
and moderate rainfall but not very satisfactory for heavy rainfall.
Abstract: The incidences of dengue hemorrhagic disease (DHF)
over the long term exhibit a seasonal behavior. It has been
hypothesized that these behaviors are due to the seasonal climate
changes which in turn induce a seasonal variation in the incubation
period of the virus while it is developing the mosquito. The standard
dynamic analysis is applied for analysis the Susceptible-Exposed-
Infectious-Recovered (SEIR) model which includes an annual
variation in the length of the extrinsic incubation period (EIP). The
presence of both asymptomatic and symptomatic infections is
allowed in the present model. We found that dynamic behavior of the
endemic state changes as the influence of the seasonal variation of
the EIP becomes stronger. As the influence is further increased, the
trajectory exhibits sustained oscillations when it leaves the chaotic
region.
Abstract: The purpose of this paper is to highlight the
importance of the concept of competitiveness in the supply chain and
to present a conceptual framework for Supply Chain Competitiveness
(SCC). The framework is based on supply chain activities, which are
inputs, necessary for SCC and the benefits which are the outputs of
SCC. A literature review is conducted on key supply chain
competitiveness issues, its determinants, its various dimensions
followed by exploration for SCC. Based on the insights gained, a
conceptual framework for SCC is presented based on activities for
SCC, SCC environment and outcomes of SCC. The information flow
in the conceptual framework is bi-directional at all levels and the
activities are interrelated in a global competitive environment. The
activities include the activities of suppliers, manufacturers and
distributors, giving more emphasis on manufacturers- activities.
Further, implications of various factors such as economic, politicolegal,
technical, socio-cultural, competition, demographic etc. are
also highlighted. The SCC framework is an attempt to cover the
relatively less explored area of supply chain competitiveness. It is
expected that this work will further motivate researchers,
academicians and practitioners to work in this area and offers
conceptual help in providing a directions for supply chain
competitiveness which leads to improvement in the supply chain and
supply chain performance.
Abstract: Although there are many theories and discussion of leadership, the necessity of having a new leadership paradigm was emphasized. The existing leadership characteristic of instruction and control revealed its limitations. Market competition becomes fierce and economic recession never ends worldwide. Of the leadership theories, servant leadership was introduced recently and is in line with the environmental changes of the organization. Servant leadership is a combination of two words, 'servant' and 'leader' and can be defined as the role of the leader who focuses on doing voluntary work for others with altruistic ethics, makes members, customers, and local communities a priority, and makes a commitment to satisfying their needs. This leadership received attention as one field of leadership in the late 1990s and secured its legitimacy. This study discusses the existing research trends of leadership, the concept, behavior characteristics, and lower dimensions of servant leadership, compares servant leadership with the existing leadership researches and diagnoses if servant leadership is a useful concept for further leadership researches. Finally, this study criticizes the limitations in the existing researches on servant leadership.
Abstract: Three dimensional analysis of thermal model in laser
full penetration welding, Nd:YAG, by transparent mode DP600 alloy
steel 1.25mm of thickness and gap of 0.1mm. Three models studied
the influence of thermal dependent temperature properties, thermal
independent temperature and the effect of peak value of specific heat
at phase transformation temperature, AC1, on the transient
temperature. Another seven models studied the influence of
discretization, meshes on the temperature distribution in weld plate.
It is shown that for the effects of thermal properties, the errors less
4% of maximum temperature in FZ and HAZ have identified. The
minimum value of discretization are at least one third increment per
radius for temporal discretization and the spatial discretization
requires two elements per radius and four elements through thickness
of the assembled plate, which therefore represent the minimum
requirements of modeling for the laser welding in order to get
minimum errors less than 5% compared to the fine mesh.
Abstract: CONWIP (constant work-in-process) as a pull
production system have been widely studied by researchers to date.
The CONWIP pull production system is an alternative to pure push
and pure pull production systems. It lowers and controls inventory
levels which make the throughput better, reduces production lead
time, delivery reliability and utilization of work. In this article a
CONWIP pull production system was simulated. It was simulated
push and pull planning system. To compare these systems via a
production planning system (PPS) game were adjusted parameters of
each production planning system. The main target was to reduce the
total WIP and achieve throughput and delivery reliability to
minimum values. Data was recorded and evaluated. A future state
was made for real production of plastic components and the setup of
the two indicators with CONWIP pull production system which can
greatly help the company to be more competitive on the market.
Abstract: As the Textile Industry is the second largest industry
in Egypt and as small and medium-sized enterprises (SMEs) make up
a great portion of this industry therein it is essential to apply the
concept of Cleaner Production for the purpose of reducing pollution.
In order to achieve this goal, a case study concerned with ecofriendly
stone-washing of jeans-garments was investigated. A raw
material-substitution option was adopted whereby the toxic
potassium permanganate and sodium sulfide were replaced by the
environmentally compatible hydrogen peroxide and glucose
respectively where the concentrations of both replaced chemicals
together with the operating time were optimized. In addition, a
process-rationalization option involving four additional processes
was investigated. By means of criteria such as product quality,
effluent analysis, mass and heat balance; and cost analysis with the
aid of a statistical model, a process optimization treatment revealed
that the superior process optima were 50%, 0.15% and 50min for
H2O2 concentration, glucose concentration and time, respectively.
With these values the superior process ought to reduce the annual
cost by about EGP 105 relative to the currently used conventional
method.
Abstract: This paper presents a novel approach for representing
the spatio-temporal topology of the camera network with overlapping
and non-overlapping fields of view (FOVs). The topology is
determined by tracking moving objects and establishing object
correspondence across multiple cameras. To track people successfully
in multiple camera views, we used the Merge-Split (MS) approach for
object occlusion in a single camera and the grid-based approach for
extracting the accurate object feature. In addition, we considered the
appearance of people and the transition time between entry and exit
zones for tracking objects across blind regions of multiple cameras
with non-overlapping FOVs. The main contribution of this paper is to
estimate transition times between various entry and exit zones, and to
graphically represent the camera topology as an undirected weighted
graph using the transition probabilities.
Abstract: Wireless sensor networks (WSNs) consist of number
of tiny, low cost and low power sensor nodes to monitor some physical phenomenon. The major limitation in these networks is the use of non-rechargeable battery having limited power supply. The
main cause of energy consumption in such networks is
communication subsystem. This paper presents an energy efficient
Cluster Cooperative Caching at Sensor (C3S) based upon grid type clustering. Sensor nodes belonging to the same cluster/grid form a
cooperative cache system for the node since the cost for
communication with them is low both in terms of energy
consumption and message exchanges. The proposed scheme uses
cache admission control and utility based data replacement policy to
ensure that more useful data is retained in the local cache of a node.
Simulation results demonstrate that C3S scheme performs better in
various performance metrics than NICoCa which is existing
cooperative caching protocol for WSNs.
Abstract: Navigation is the processes of monitoring and
controlling the movement of an object from one place to another.
Currently, Global Positioning System (GPS) is the main navigation
system used all over the world for navigation applications. GPS
receiver receives signals from at least three satellites to locate and
display itself. Displayed positioning information is updated
continuously. Update rate is the number of times per second that a
display is illuminated. The speed of update is governed by receiver
update rate. A higher update rate decreases display lag time and
improves distance measurements and tracking especially when
moving on a curvy route. The majority of GPS receivers used
nowadays are updated every second continuously. This period is
considered reasonable for some applications while it is long relatively
for high speed applications. In this paper, the suitability and
feasibility of GPS receiver with different update rates will be
evaluated for various applications according to the level of speed and
update rate needed for particular applications.