Abstract: In power systems, protective relays must filter their
inputs to remove undesirable quantities and retain signal quantities of
interest. This job must be performed accurate and fast. A new
method for filtering the undesirable components such as DC and
harmonic components associated with the fundamental system
signals. The method is s based on a dynamic filtering algorithm. The
filtering algorithm has many advantages over some other classical
methods. It can be used as dynamic on-line filter without the need of
parameters readjusting as in the case of classic filters. The proposed
filter is tested using different signals. Effects of number of samples
and sampling window size are discussed. Results obtained are
presented and discussed to show the algorithm capabilities.
Abstract: An evaluation of the PCBs residues in the surface soils from Bacninh, Vietnam was carried out. Sixty representative soil samples were collected from the centre of Bacninh and three surrounding districts. The analyzed results indicated the wide extent of contamination of total PCBs in Bacninh. In industrial and urban zones, total PCBs concentrations ranged from ranged from
Abstract: Process control and energy conservation are the two
primary reasons for using an adjustable speed drive. However,
voltage sags are the most important power quality problems facing
many commercial and industrial customers. The development of
boost converters has raised much excitement and speculation
throughout the electric industry. Now utilities are looking to these
devices for performance improvement and reliability in a variety of
areas. Examples of these include sags, spikes, or transients in supply
voltage as well as unbalanced voltages, poor electrical system
grounding, and harmonics. In this paper, simulations results are
presented for the verification of the proposed boost converter
topology. Boost converter provides ride through capability during
sag and swell. Further, input currents are near sinusoidal. This
eliminates the need of braking resistor also.
Abstract: This experiment was conducted to investigate the
effect of dietary supplementation of different levels of black seed
(Nigella sativa L.) on the performance and immune response of broiler chicks. A total 240 day-old broiler chicks were used and
randomly allotted equally into six experimental groups designated as 1, 2, 3, 4, 5 and 6 having black seed at the rate of 0, 2, 4, 6, 8 and
10 g /kg diet respectively. The study was lasted for 42 days. Average body weight, weight gain, relative growth rate, feed
conversion, antibody titer against Newcastle disease, phagocytic activity and phagocytic index, some blood parameters(GOT, GPT,
Glucose, Cholesterol, Triglyceride, Total protein, Albumen, WBCs,
RBCs, Hb and PCV), dressing percentage, weight of different body
organs, abdominal fat weight, were determined. It was found that, N. Sativa significantly improved final body weight, total body gain
and feed conversion ratio of groups 2 and 3 when compared with the control group. Higher levels of N. Sativa did not improve
growth performance of the chicks. Non significant differences were
observed for antibody titer against Newcastle virus, WBCs count,
serum GOT, glucose level, dressing %, relative liver, spleen, heart and head percentages. Lymphoid organs (Bursa and Thymus)
improved significantly with increasing N. Sativa level in all supplemented groups. Serum cholesterol, triglyceride and visible fat
% significantly decreased with Nigella sativa supplementation while
serum GPT level significantly increased with nigella sativa
supplementation.
Abstract: In this paper, we present parallel alternating two-stage
methods for solving linear system Ax=b, where A is a symmetric
positive definite matrix. And we give some convergence results of
these methods for nonsingular linear system.
Abstract: In order to derive important parameters concerning
mobile subscriber MS with ongoing calls in Low Earth Orbit Mobile
Satellite Systems LEO MSSs, a positioning system had to be
integrated into MSS in order to localize mobile subscribers MSs and
track them during the connection. Such integration is regarded as a
complex implementation.
We propose in this paper a novel method based on advantages of
mobility model of Low Earth Orbit Mobile Satellite System LEO
MSS called Evaluation Parameters Method EPM which allows for
such systems the evaluation of different information concerning a
MS with a call in progress even if its location is unknown.
Abstract: This paper is a numerical investigation of a laminar
isothermal plane two dimensional wall jet. Special attention has been
paid to the effect of the inlet conditions at the nozzle exit on the
hydrodynamic and thermal characteristics of the flow. The
behaviour of various fluids evolving in both forced and mixed
convection regimes near a vertical plate plane is carried out. The
system of governing equations is solved with an implicit finite
difference scheme. For numerical stability we use a staggered non
uniform grid. The obtained results show that the effect of the Prandtl
number is significant in the plume region in which the jet flow is
governed by buoyant forces. Further for ascending X values, the
buoyancy forces become dominating, and a certain agreement
between the temperature profiles are observed, which shows that the
velocity profile has no longer influence on the wall temperature
evolution in this region. Fluids with low Prandtl number warm up
more importantly, because for such fluids the effect of heat diffusion
is higher.
Abstract: This paper present an efficient and reliable technique of optimization which combined fuel cost economic optimization and emission dispatch using the Sigmoid Decreasing Inertia Weight Particle Swarm Optimization algorithm (PSO) to reduce the cost of fuel and pollutants resulting from fuel combustion by keeping the output of generators, bus voltages, shunt capacitors and transformer tap settings within the security boundary. The performance of the proposed algorithm has been demonstrated on IEEE 30-bus system with six generating units. The results clearly show that the proposed algorithm gives better and faster speed convergence then linearly decreasing inertia weight.
Abstract: This paper describes the development of a 16-ports optical code division multiple access (OCDMA) encoder prototype based on Arrayed Waveguide Grating (AWG) and optical switches. It is potentially to provide a high security for data transmission due to all data will be transmitted in binary code form. The output signals from AWG are coded with a binary code that given to an optical switch before it signal modulate with the carrier and transmitted to the receiver. The 16-ports encoder used 16 double pole double throw (DPDT) toggle switches to control the polarization of voltage source from +5 V to -5 V for 16 optical switches. When +5 V is given, the optical switch will give code '1' and vice versa. The experimental results showed the insertion loss, crosstalk, uniformity, and optical signal-noise-ratio (OSNR) for the developed prototype are
Abstract: A gene network gives the knowledge of the regulatory
relationships among the genes. Each gene has its activators and
inhibitors that regulate its expression positively and negatively
respectively. Genes themselves are believed to act as activators and
inhibitors of other genes. They can even activate one set of genes and
inhibit another set. Identifying gene networks is one of the most
crucial and challenging problems in Bioinformatics. Most work done
so far either assumes that there is no time delay in gene regulation or
there is a constant time delay. We here propose a Dynamic Time-
Lagged Correlation Based Method (DTCBM) to learn the gene
networks, which uses time-lagged correlation to find the potential
gene interactions, and then uses a post-processing stage to remove
false gene interactions to common parents, and finally uses dynamic
correlation thresholds for each gene to construct the gene network.
DTCBM finds correlation between gene expression signals shifted in
time, and therefore takes into consideration the multi time delay
relationships among the genes. The implementation of our method is
done in MATLAB and experimental results on Saccharomyces
cerevisiae gene expression data and comparison with other methods
indicate that it has a better performance.
Abstract: Texture classification is an important image processing
task with a broad application range. Many different techniques for
texture classification have been explored. Using sparse approximation
as a feature extraction method for texture classification is a relatively
new approach, and Skretting et al. recently presented the Frame
Texture Classification Method (FTCM), showing very good results on
classical texture images. As an extension of that work the FTCM is
here tested on a real world application as detection of abnormalities
in mammograms. Some extensions to the original FTCM that are
useful in some applications are implemented; two different smoothing
techniques and a vector augmentation technique. Both detection of
microcalcifications (as a primary detection technique and as a last
stage of a detection scheme), and soft tissue lesions in mammograms
are explored. All the results are interesting, and especially the results
using FTCM on regions of interest as the last stage in a detection
scheme for microcalcifications are promising.
Abstract: Considering complexity of products, new geometrical
design and investment tolerances that are necessary, measuring and
dimensional controlling involve modern and more precise methods.
Photo digitizing method using two cameras to record pictures and
utilization of conventional method named “cloud points" and data
analysis by the use of ATOUS software, is known as modern and
efficient in mentioned context. In this paper, benefits of photo
digitizing method in evaluating sampling of machining processes
have been put forward. For example, assessment of geometrical
integrity surface in 5-axis milling process and measurement of
carbide tool wear in turning process, can be can be brought forward.
Advantages of this method comparing to conventional methods have
been expressed.
Abstract: Misalignment and unbalance are the major concerns
in rotating machinery. When the power supply to any rotating system
is cutoff, the system begins to lose the momentum gained during
sustained operation and finally comes to rest. The exact time period
from when the power is cutoff until the rotor comes to rest is called
Coast Down Time. The CDTs for different shaft cutoff speeds were
recorded at various misalignment and unbalance conditions. The
CDT reduction percentages were calculated for each fault and there
is a specific correlation between the CDT reduction percentage and
the severity of the fault. In this paper, radial basis network, a new
generation of artificial neural networks, has been successfully
incorporated for the prediction of CDT for misalignment and
unbalance conditions. Radial basis network has been found to be
successful in the prediction of CDT for mechanical faults in rotating
machinery.
Abstract: The objective of this research seeks to transmit a distance training model to the community in the upper northeastern region. The group sampling consists of 60 community leaders in the municipality of sub-district Kumphawapi, Kumphawapi Disrict, Udonthani Province. The research tools rely on the following instruments, they are : 1) the achievement test of community leaders- training and 2) the satisfaction questionnaires of community leaders. The statistics used in data analysis takes the statistical mean, percentage, standard deviation, and statistical T-test. The resulted findings reveal : 1) the efficiency of the distance training developed by the researcher for the community leaders joining in the training received the average score between in-training and post-training period higher than the setup criterion, 2) the two groups of participants in the training achieved higher knowledge than their pre-training state, 3) the comparison of the achievements between the two group presented no different results, 4) the community leaders obtained the high-to-highest satisfaction.
Abstract: This paper describes the design of a voltage based maximum power point tracker (MPPT) for photovoltaic (PV) applications. Of the various MPPT methods, the voltage based method is considered to be the simplest and cost effective. The major disadvantage of this method is that the PV array is disconnected from the load for the sampling of its open circuit voltage, which inevitably results in power loss. Another disadvantage, in case of rapid irradiance variation, is that if the duration between two successive samplings, called the sampling period, is too long there is a considerable loss. This is because the output voltage of the PV array follows the unchanged reference during one sampling period. Once a maximum power point (MPP) is tracked and a change in irradiation occurs between two successive samplings, then the new MPP is not tracked until the next sampling of the PV array voltage. This paper proposes an MPPT circuit in which the sampling interval of the PV array voltage, and the sampling period have been shortened. The sample and hold circuit has also been simplified. The proposed circuit does not utilize a microcontroller or a digital signal processor and is thus suitable for low cost and low power applications.
Abstract: Polymer melt compressibility and mold surface roughness, which are generally ignored during the filling stage of the conventional injection molding, may become increasingly significant in micro injection molding where the parts become smaller. By employing the 2.5D generalized Hele-Shaw model, we presented here the effects of polymer compressibility and mold surface roughness on mold-filling in a micro-thickness cavity. To elucidate the effects of surface roughness, numerical investigations were conducted using a cavity flat plate which has two halves with different surface roughness. This allows the comparison of flow field on two different halves under identical processing conditions but with different roughness. Results show that polymer compressibility and mold surface roughness have effects on mold filling in micro injection molding. There is in shrinkage reduction as the density is increased due to polymer melt compressibility during the filling stage.
Abstract: The demand for new telecommunication services requiring higher capacities, data rates and different operating modes have motivated the development of new generation multi-standard wireless transceivers. A multi-standard design often involves extensive system level analysis and architectural partitioning, typically requiring extensive calculations. In this research, a decimation filter design tool for wireless communication standards consisting of GSM, WCDMA, WLANa, WLANb, WLANg and WiMAX is developed in MATLAB® using GUIDE environment for visual analysis. The user can select a required wireless communication standard, and obtain the corresponding multistage decimation filter implementation using this toolbox. The toolbox helps the user or design engineer to perform a quick design and analysis of decimation filter for multiple standards without doing extensive calculation of the underlying methods.
Abstract: Ground-level tropospheric ozone is one of the air
pollutants of most concern. It is mainly produced by photochemical
processes involving nitrogen oxides and volatile organic compounds
in the lower parts of the atmosphere. Ozone levels become
particularly high in regions close to high ozone precursor emissions
and during summer, when stagnant meteorological conditions with
high insolation and high temperatures are common.
In this work, some results of a study about urban ozone
distribution patterns in the city of Badajoz, which is the largest and
most industrialized city in Extremadura region (southwest Spain) are
shown. Fourteen sampling campaigns, at least one per month, were
carried out to measure ambient air ozone concentrations, during
periods that were selected according to favourable conditions to
ozone production, using an automatic portable analyzer.
Later, to evaluate the ozone distribution at the city, the measured
ozone data were analyzed using geostatistical techniques. Thus, first,
during the exploratory analysis of data, it was revealed that they were
distributed normally, which is a desirable property for the subsequent
stages of the geostatistical study. Secondly, during the structural
analysis of data, theoretical spherical models provided the best fit for
all monthly experimental variograms. The parameters of these
variograms (sill, range and nugget) revealed that the maximum
distance of spatial dependence is between 302-790 m and the
variable, air ozone concentration, is not evenly distributed in reduced
distances. Finally, predictive ozone maps were derived for all points
of the experimental study area, by use of geostatistical algorithms
(kriging). High prediction accuracy was obtained in all cases as
cross-validation showed. Useful information for hazard assessment
was also provided when probability maps, based on kriging
interpolation and kriging standard deviation, were produced.
Abstract: This paper presents the approach to design the Auto-
Tuning PID controller for interactive Water Level Process using
integral step response. The Integral Step Response (ISR) is the
method to model a dynamic process which can be done easily,
conveniently and very efficiently. Therefore this method is advantage
for design the auto tune PID controller. Our scheme uses the root
locus technique to design PID controller. In this paper MATLAB is
used for modeling and testing of the control system. The
experimental results of the interacting water level process can be
satisfyingly illustrated the transient response and the steady state
response.
Abstract: In this paper we intend to ascertain the state of the art on multifingered end-effectors, also known as robotic hands or dexterous robot hands, and propose an experimental setup for an innovative task based design approach, involving cutting edge technologies in motion capture. After an initial description of the capabilities and complexity of a human hand when grasping objects, in order to point out the importance of replicating it, we analyze the mechanical and kinematical structure of some important works carried out all around the world in the last three decades and also review the actuators and sensing technologies used. Finally we describe a new design philosophy proposing an experimental setup for the first stage using recent developments in human body motion capture systems that might lead to lighter and always more dexterous robotic hands.