Abstract: In this paper, a new adaptive Fourier decomposition
(AFD) based time-frequency speech analysis approach is proposed.
Given the fact that the fundamental frequency of speech signals often
undergo fluctuation, the classical short-time Fourier transform (STFT)
based spectrogram analysis suffers from the difficulty of window size
selection. AFD is a newly developed signal decomposition theory. It is
designed to deal with time-varying non-stationary signals. Its
outstanding characteristic is to provide instantaneous frequency for
each decomposed component, so the time-frequency analysis becomes
easier. Experiments are conducted based on the sample sentence in
TIMIT Acoustic-Phonetic Continuous Speech Corpus. The results
show that the AFD based time-frequency distribution outperforms the
STFT based one.
Abstract: This paper proposes a zero-voltage transition (ZVT) PWM synchronous buck converter, which is designed to operate at low output voltage and high efficiency typically required for portable systems. To make the DC-DC converter efficient at lower voltage, synchronous converter is an obvious choice because of lower conduction loss in the diode. The high-side MOSFET is dominated by the switching losses and it is eliminated by the soft switching technique. Additionally, the resonant auxiliary circuit designed is also devoid of the switching losses. The suggested procedure ensures an efficient converter. Theoretical analysis, computer simulation, and experimental results are presented to explain the proposed schemes.
Abstract: A reliable estimate of the average bond stress within
the anchorage of steel reinforcing bars in tension is critically
important for the design of reinforced concrete member. This paper
describes part of a recently completed experimental research program
in the Centre for Infrastructure Engineering and Safety (CIES) at the
University of New South Wales, Sydney, Australia aimed at
assessing the effects of different factors on the anchorage
requirements of modern high strength steel reinforcing bars. The
study found that an increase in the anchorage length and bar diameter
generally leads to a reduction of the average ultimate bond stress. By
the extension of a well established analytical model of bond and
anchorage, it is shown here that the differences in the average
ultimate bond stress for different anchorage lengths is associated with
the variable degree of plastic deformation in the tensile zone of the
concrete surrounding the bar.
Abstract: In this paper, based on flume experimental data, the velocity distribution in open channel flows is re-investigated. From the analysis, it is proposed that the wake layer in outer region may be divided into two regions, the relatively weak outer region and the relatively strong outer region. Combining the log law for inner region and the parabolic law for relatively strong outer region, an explicit equation for mean velocity distribution of steady and uniform turbulent flow through straight open channels is proposed and verified with the experimental data. It is found that the sediment concentration has significant effect on velocity distribution in the relatively weak outer region.
Abstract: Hysteresis phenomenon has been observed in the
operations of both horizontal-axis and vertical-axis wind turbines
(HAWTs and VAWTs). In this study, wind tunnel experiments were
applied to investigate the characters of hysteresis phenomena between
the angular speed and the external resistance of electrical loading
during the operation of a Darrieus type VAWT. Data of output voltage,
output current, angular speed of wind turbine under different wind
speeds are measured and analyzed. Results show that the range of
external resistance changes with the wind speed. The range decreases
as the wind speed increases following an exponential decay form.
Experiments also indicate that the maximum output power of wind
turbines is always inside the range where hysteresis happened. These
results provide an important reference to the design of output control
system of wind turbines.
Abstract: This study was carried out experimentally and analytically about the performance of solar cell panel system for operating the pump coupled by dc-motor. The solar cell panel with total area 1.9848 m2 consists of three modules of 80 Wp each. The small centrifugal pump powered by dc-motor is operated to lift water from 1m to 7m heads in sequence and gives the amount of water pumped over the whole day from 08.00 to 16.00 h are 11988, 10851, 8874, 7695, 5760, 3600, 2340 L/d respectively. The hourly global solar radiation during the day is an average of 506 W/m2. This study also presents the I-V characteristics of the panel at global radiations 200, 400, 600, 800 and 1000 W/m2 matched with the operation of the pump at the above lifting heads. It proves that the only solar radiations 800 and 1000 W/m2 could provide lifting head from 1m to 7m. The analysis shows the best efficiency point of the performance of solar cell panel system occurs at the pumping head 2.89 m.
Abstract: The main objective of this article is to present the semi-active vibration control using an electro-rheological fluid embedded sandwich structure for a cantilever beam. ER fluid is a smart material, which cause the suspended particles polarize and connect each other to form chain. The stiffness and damping coefficients of the ER fluid can be changed in 10 micro seconds; therefore, ERF is suitable to become the material embedded in the tunable vibration absorber to become a smart absorber. For the ERF smart material embedded structure, the fuzzy control law depends on the experimental expert database and the proposed self-tuning strategy. The electric field is controlled by a CRIO embedded system to implement the real application. This study investigates the different performances using the Type-1 fuzzy and interval Type-2 fuzzy controllers. The Interval type-2 fuzzy control is used to improve the modeling uncertainties for this ERF embedded shock absorber. The self-tuning vibration controllers using Type-1 and Interval Type-2 fuzzy law are implemented to the shock absorber system. Based on the resulting performance, Internal Type-2 fuzzy is better than the traditional Type-1 fuzzy control for this vibration control system.
Abstract: Conventional approaches in the implementation of logic programming applications on embedded systems are solely of software nature. As a consequence, a compiler is needed that transforms the initial declarative logic program to its equivalent procedural one, to be programmed to the microprocessor. This approach increases the complexity of the final implementation and reduces the overall system's performance. On the contrary, presenting hardware implementations which are only capable of supporting logic programs prevents their use in applications where logic programs need to be intertwined with traditional procedural ones, for a specific application. We exploit HW/SW codesign methods to present a microprocessor, capable of supporting hybrid applications using both programming approaches. We take advantage of the close relationship between attribute grammar (AG) evaluation and knowledge engineering methods to present a programmable hardware parser that performs logic derivations and combine it with an extension of a conventional RISC microprocessor that performs the unification process to report the success or failure of those derivations. The extended RISC microprocessor is still capable of executing conventional procedural programs, thus hybrid applications can be implemented. The presented implementation is programmable, supports the execution of hybrid applications, increases the performance of logic derivations (experimental analysis yields an approximate 1000% increase in performance) and reduces the complexity of the final implemented code. The proposed hardware design is supported by a proposed extended C-language called C-AG.
Abstract: The aim of this paper is to present the kinematic
analysis and mechanism design of an assistive robotic leg for
hemiplegic and hemiparetic patients. In this work, the priority is to
design and develop the lightweight, effective and single driver
mechanism on the basis of experimental hip and knee angles- data for
walking speed of 1 km/h. A mechanism of cam-follower with three
links is suggested for this purpose. The kinematic analysis is carried
out and analysed using commercialized MATLAB software based on
the prototype-s links sizes and kinematic relationships. In order to
verify the kinematic analysis of the prototype, kinematic analysis data
are compared with the experimental data. A good agreement between
them proves that the anthropomorphic design of the lower extremity
exoskeleton follows the human walking gait.
Abstract: In the present work, the effective moisture diffusivity
and activation energy were calculated using an infinite series solution
of Fick-s diffusion equation. The results showed that increasing
drying temperature accelerated the drying process. All drying
experiments had only falling rate period. The average effective
moisture diffusivity values varied from 2.807x10-10 to 6.977x10-10m2
s_1 over the temperature and velocity range. The temperature
dependence of the effective moisture diffusivity for the thin layer
drying of the ginger slices was satisfactorily described by an
Arrhenius-type relationship with activation energy values of 19.313-
22.722 kJ.mol-1 within 40–70 °C and 0.8-3 ms-1 temperature range.
Abstract: A low cost Short Message System (SMS) based Home security system equipped with motion, smoke, temperature, humidity and light sensors has been studied and tested. The sensors are controlled by a microprocessor PIC 18F4520 through the SMS having password protection code for the secure operation. The user is able to switch light and the appliances and get instant feedback. Also in cases of emergencies such as fire or robbery the system will send alert message to occupant and relevant civil authorities. The operation of the home security has been tested on Vodafone- Fiji network and Digicel Fiji Network for emergency and feedback responses for 25 samples. The experiment showed that it takes about 8-10s for the security system to respond in case of emergency. It takes about 18-22s for the occupant to switch and monitor lights and appliances and then get feedback depending upon the network traffic.
Abstract: There are reports of gas and oil wells fire due to different accidents. Many different methods are used for fire fighting in gas and oil industry. Traditional fire extinguishing techniques are mostly faced with many problems and are usually time consuming and needs lots of equipments. Besides, they cause damages to facilities, and create health and environmental problems. This article proposes innovative approach in fire extinguishing techniques in oil and gas industry, especially applicable for burning oil wells located offshore. Fire extinguishment employing a turbojet is a novel approach which can help to extinguishment the fire in short period of time. Divergent and convergent turbojets modeled in laboratory scale along with a high pressure flame were used. Different experiments were conducted to determine the relationship between output discharges of trumpet and oil wells. The results were corrected and the relationship between dimensionless parameters of flame and fire extinguishment distances and also the output discharge of turbojet and oil wells in specified distances are demonstrated by specific curves.
Abstract: In this paper we propose a new approach for flexible document categorization according to the document type or genre instead of topic. Our approach implements two homogenous classifiers: contextual classifier and logical classifier. The contextual classifier is based on the document URL, whereas, the logical classifier use the logical structure of the document to perform the categorization. The final categorization is obtained by combining contextual and logical categorizations. In our approach, each document is assigned to all predefined categories with different membership degrees. Our experiments demonstrate that our approach is best than other genre categorization approaches.
Abstract: This paper presents an automatic feature recognition
method based on center-surround difference detecting and fuzzy logic
that can be applied in ground-penetrating radar (GPR) image
processing. Adopted center-surround difference method, the salient
local image regions are extracted from the GPR images as features of
detected objects. And fuzzy logic strategy is used to match the
detected features and features in template database. This way, the
problem of objects detecting, which is the key problem in GPR image
processing, can be converted into two steps, feature extracting and
matching. The contributions of these skills make the system have the
ability to deal with changes in scale, antenna and noises. The results of
experiments also prove that the system has higher ratio of features
sensing in using GPR to image the subsurface structures.
Abstract: Single nucleotide polymorphisms (SNPs) hold much promise as a basis for disease-gene association. However, research is limited by the cost of genotyping the tremendous number of SNPs. Therefore, it is important to identify a small subset of informative SNPs, the so-called tag SNPs. This subset consists of selected SNPs of the genotypes, and accurately represents the rest of the SNPs. Furthermore, an effective evaluation method is needed to evaluate prediction accuracy of a set of tag SNPs. In this paper, a genetic algorithm (GA) is applied to tag SNP problems, and the K-nearest neighbor (K-NN) serves as a prediction method of tag SNP selection. The experimental data used was taken from the HapMap project; it consists of genotype data rather than haplotype data. The proposed method consistently identified tag SNPs with considerably better prediction accuracy than methods from the literature. At the same time, the number of tag SNPs identified was smaller than the number of tag SNPs in the other methods. The run time of the proposed method was much shorter than the run time of the SVM/STSA method when the same accuracy was reached.
Abstract: The electrolyte stirring method of anodization etching
process for manufacturing porous silicon (PS) is reported in this work.
Two experimental setups of nature air stirring (PS-ASM) and
electrolyte stirring (PS-ESM) are employed to clarify the influence of
stirring mechanisms on electrochemical etching process. Compared to
traditional fabrication without any stirring apparatus (PS-TM), a large
plateau region of PS surface structure is obtained from samples with
both stirring methods by the 3D-profiler measurement. Moreover, the
light emission response is also improved by both proposed electrolyte
stirring methods due to the cycling force in electrolyte could
effectively enhance etch-carrier distribution while the electrochemical
etching process is made. According to the analysis of statistical
calculation of photoluminescence (PL) intensity, lower standard
deviations are obtained from PS-samples with studied stirring methods,
i.e. the uniformity of PL-intensity is effectively improved. The
calculated deviations of PL-intensity are 93.2, 74.5 and 64,
respectively, for PS-TM, PS-ASM and PS-ESM.
Abstract: In this paper, a novel deinterlacing algorithm is
proposed. The proposed algorithm approximates the distribution of the
luminance into a polynomial function. Instead of using one
polynomial function for all pixels, different polynomial functions are
used for the uniform, texture, and directional edge regions. The
function coefficients for each region are computed by matrix
multiplications. Experimental results demonstrate that the proposed
method performs better than the conventional algorithms.
Abstract: In this article, using finite element analysis (FEA)
and an X-ray diffractometer (XRD), cold-sprayed titanium particles
on a steel substrate is investigated in term of cooling time and the
development of residual strains. Three cooling-down models of
sprayed particles after deposition stage are simulated and discussed:
the first model (m1) considers conduction effect to the substrate only,
the second model (m2) considers both conduction as well as
convection effect to the environment, and the third model (m3) which
is the same as the second model but with the substrate heated to a
near particle temperature before spraying. Thereafter, residual strains
developed in the third model is compared with the experimental
measurement of residual strains, which involved a Bruker D8
Advance Diffractometer using CuKa radiation (40kV, 40mA)
monochromatised with a graphite sample monochromator. For
deposition conditions of this study, a good correlation was found to
exist between the FEA results and XRD measurements of residual
strains.
Abstract: This paper presents a solution for ceramic cutting tools availability in interrupted machining. Experiments were performed on a special fixture – the interrupted cut simulator. This fixture was constructed at our Department of Machining and Assembly within the scope of a project by the Czech Science Foundation. The goals of the tests were to contribute to the wider usage of these cutting materials in machining, especially in interrupted machining. Through the centuries, producers of ceramic cutting tools have taken big steps forward. Namely, increasing durability in maintaining high levels of strength and hardness lends an advantage. Some producers of these materials advise cutting inserts for interrupted machining at the present time [1, 2].
Abstract: Wavelet transforms are multiresolution
decompositions that can be used to analyze signals and images.
Image compression is one of major applications of wavelet
transforms in image processing. It is considered as one of the most
powerful methods that provides a high compression ratio. However,
its implementation is very time-consuming. At the other hand,
parallel computing technologies are an efficient method for image
compression using wavelets. In this paper, we propose a parallel
wavelet compression algorithm based on quadtrees. We implement
the algorithm using MatlabMPI (a parallel, message passing version
of Matlab), and compute its isoefficiency function, and show that it is
scalable. Our experimental results confirm the efficiency of the
algorithm also.