Abstract: This study investigated the pattern and seasonal index of influenza cases in Thailand. Our results showed that southern Thailand had the highest influenza incidence among the four regions of Thailand (i.e. north, northeast, central and southern Thailand). The influenza pattern in southern Thailand was similar to that of northeastern Thailand. Seasonal index values of influenza cases in Thailand were higher in the hot season than in the wet season. Influenza cases started to increase at the beginning of the hot season (April), reached a maximum in August, rapidly declined in the middle of the wet season and reached the lowest value in December. Seasonal index values for northern Thailand differed from other regions of Thailand.
Abstract: The evolution of technology and construction techniques has enabled the upgrading of transport networks. In particular, the high-speed rail networks allow convoys to peak at above 300 km/h. These structures, however, often significantly impact the surrounding environment. Among the effects of greater importance are the ones provoked by the soundwave connected to train transit. The wave propagation affects the quality of life in areas surrounding the tracks, often for several hundred metres. There are substantial damages to properties (buildings and land), in terms of market depreciation. The present study, integrating expertise in acoustics, computering and evaluation fields, outlines a useful model to select project paths so as to minimize the noise impact and reduce the causes of possible litigation. It also facilitates the rational selection of initiatives to contain the environmental damage to the already existing railway tracks. The research is developed with reference to the Italian regulatory framework (usually more stringent than European and international standards) and refers to a case study concerning the high speed network in Italy.
Abstract: 2D/3D registration is a special case of medical image
registration which is of particular interest to surgeons. Applications
of 2D/3D registration are [1] radiotherapy planning and treatment
verification, spinal surgery, hip replacement, neurointerventions and
aortic stenting. The purpose of this paper is to provide a literature
review of the main methods for image registration for the 2D/3D
case. At the end of the paper an algorithm is proposed for 2D/3D
registration based on the Chebyssev polynomials iteration loop.
Abstract: A numerical study on the heat transfer in the thermal
barrier coatings and the substrates of a parallel-plate enclosure is
carried out. Some of the thermal barrier coatings, such as ceramics, are
semitransparent and are of interest for high-temperature applications
where radiation effects are significant. The radiative transfer equations
and the energy equations are solved by using the discrete ordinates
method and the finite difference method. Illustrative results are
presented for temperature distributions in the coatings and the opaque
walls under various heating conditions. The results show that the
temperature distribution is more uniform in the interior portion of each
coating away from its boundary for the case with a larger average of
varying refractive index and a positive gradient of refractive index
enhances radiative transfer to the substrates.
Abstract: In this paper, we first introduce the model of games on augmenting systems with a coalition structure, which can be seen as an extension of games on augmenting systems. The core of games on augmenting systems with a coalition structure is defined, and an equivalent form is discussed. Meantime, the Shapley function for this type of games is given, and two axiomatic systems of the given Shapley function are researched. When the given games are quasi convex, the relationship between the core and the Shapley function is discussed, which does coincide as in classical case. Finally, a numerical example is given.
Abstract: Analyse of locally manufactured Low Density Polyethylene (LDPE) durability, used within lining systems at bottom of Municipal Solid Waste (landfill), is done in the present work. For this end, short and middle time creep behavior under tension of the analyzed material is carried out. The locally manufactured material is tested and compared to the European one (LDPE-CE). Both materials was tested in 03 various mediums: ambient and two aggressive (salty water and foam water), using three specimens in each case. A testing campaign is carried out using an especially designed and achieved testing bench. Moreover, characterisation tests were carried out to evaluate the medium effect on the mechanical properties of the tested material (LDPE). Furthermore, experimental results have been used to establish a law regression which can be used to predict creep behaviour of the analyzed material. As a result, the analyzed LDPE material has showed a good stability in different ambient and aggressive mediums; as well, locally manufactured LDPE seems more flexible, compared with the European one. This makes it more useful to the desired application.
Abstract: Distance protection of transmission lines including advanced flexible AC transmission system (FACTS) devices has been a very challenging task. FACTS devices of interest in this paper are static synchronous series compensators (SSSC) and unified power flow controller (UPFC). In this paper, a new algorithm is proposed to detect and classify the fault and identify the fault position in a transmission line with respect to a FACTS device placed in the midpoint of the transmission line. Discrete wavelet transformation and wavelet entropy calculations are used to analyze during fault current and voltage signals of the compensated transmission line. The proposed algorithm is very simple and accurate in fault detection and classification. A variety of fault cases and simulation results are introduced to show the effectiveness of such algorithm.
Abstract: The belief decision tree (BDT) approach is a decision
tree in an uncertain environment where the uncertainty is represented
through the Transferable Belief Model (TBM), one interpretation
of the belief function theory. The uncertainty can appear either in
the actual class of training objects or attribute values of objects to
classify. In this paper, we develop a post-pruning method of belief
decision trees in order to reduce size and improve classification
accuracy on unseen cases. The pruning of decision tree has a
considerable intention in the areas of machine learning.
Abstract: Type 2 diabetes mellitus (T2DM) is a complex
metabolic disorder that characterized by the presence of high glucose
in blood that cause from insulin resistance and insufficiency due to
deterioration β-cell Langerhans functions. T2DM is commonly
caused by the combination of inherited genetic variations as well as
our own lifestyle. Metallothionein (MT) is a known cysteine-rich
protein responsible in helping zinc homeostasis which is important in
insulin signaling and secretion as well as protection our body from
reactive oxygen species (ROS). MT scavenged ROS and free
radicals in our body happen to be one of the reasons of T2DM and its
complications. The objective of this study was to investigate the
association of MT1A and MT2A polymorphisms between T2DM and
control subjects among Malay populations. This study involved 150
T2DM and 120 Healthy individuals of Malay ethnic with mixed
genders. The genomic DNA was extracted from buccal cells and
amplified for MT1A and MT2A loci; the 347bp and 238bp banding
patterns were respectively produced by mean of the Polymerase
Chain Reaction (PCR). The PCR products were digested with Mlucl
and Tsp451 restriction enzymes respectively and producing
fragments lengths of (158/189/347bp) and (103/135/238bp)
respectively. The ANOVA test was conducted and it shown that there
was a significant difference between diabetic and control subjects for
age, BMI, WHR, SBP, FPG, HBA1C, LDL, TG, TC and family
history with (P0.05). The genotype
frequency for AA, AG and GG of MT1A polymorphisms was 72.7%,
22.7% and 4.7% in cases and 15%, 55% and 30% in control
respectively. As for MT2A, genotype frequency of GG, GC and CC
was 42.7%, 27.3% and 30% in case and 5%, 40% and 55% for
control respectively. Both polymorphisms show significant difference
between two investigated groups with (P=0.000). The Post hoc test
was conducted and shows a significant difference between the
genotypes within each polymorphism (P=0. 000). The MT1A and
MT2A polymorphisms were believed to be the reliable molecular
markers to distinguish the T2DM subjects from healthy individuals in
Malay populations.
Abstract: It has been established that microRNAs (miRNAs) play
an important role in gene expression by post-transcriptional regulation
of messengerRNAs (mRNAs). However, the precise relationships
between microRNAs and their target genes in sense of numbers,
types and biological relevance remain largely unclear. Dissecting the
miRNA-target relationships will render more insights for miRNA
targets identification and validation therefore promote the understanding
of miRNA function. In miRBase, miRanda is the key
algorithm used for target prediction for Zebrafish. This algorithm
is high-throughput but brings lots of false positives (noise). Since
validation of a large scale of targets through laboratory experiments
is very time consuming, several computational methods for miRNA
targets validation should be developed. In this paper, we present an
integrative method to investigate several aspects of the relationships
between miRNAs and their targets with the final purpose of extracting
high confident targets from miRanda predicted targets pool. This is
achieved by using the techniques ranging from statistical tests to
clustering and association rules. Our research focuses on Zebrafish.
It was found that validated targets do not necessarily associate with
the highest sequence matching. Besides, for some miRNA families,
the frequency of their predicted targets is significantly higher in the
genomic region nearby their own physical location. Finally, in a case
study of dre-miR-10 and dre-miR-196, it was found that the predicted
target genes hoxd13a, hoxd11a, hoxd10a and hoxc4a of dre-miR-
10 while hoxa9a, hoxc8a and hoxa13a of dre-miR-196 have similar
characteristics as validated target genes and therefore represent high
confidence target candidates.
Abstract: In the multi objective optimization, in the case when generated set of Pareto optimal solutions is large, occurs the problem to select of the best solution from this set. In this paper, is suggested a method to order of Pareto set. Ordering the Pareto optimal set carried out in conformity with the introduced distance function between each solution and selected reference point, where the reference point may be adjusted to represent the preferences of a decision making agent. Preference information about objective weights from a decision maker may be expressed imprecisely. The developed elicitation procedure provides an opportunity to obtain surrogate numerical weights for the objectives, and thus, to manage impreciseness of preference. The proposed method is a scalable to many objectives and can be used independently or as complementary to the various visualization techniques in the multidimensional case.
Abstract: The study of the variability of the postural strategies
in low back pain patients, as a criterion in evaluation of the
adaptability of this system to the environmental demands is the
purpose of this study. A cross-sectional case-control study was
performed on 21 recurrent non-specific low back pain patients and 21
healthy volunteers. The electromyography activity of Deltoid,
External Oblique (EO), Transverse Abdominis/Internal Oblique
(TrA/IO) and Erector Spine (ES) muscles of each person was
recorded in 75 rapid arm flexion with maximum acceleration.
Standard deviation of trunk muscles onset relative to deltoid muscle
onset were statistically analyzed by MANOVA . The results show
that chronic low back pain patients exhibit less variability in their
anticipatory postural adjustments (APAs) in comparison with the
control group. There is a decrease in variability of postural control
system of recurrent non-specific low back pain patients that can
result in the persistence of pain and chronicity by decreasing the
adaptability to environmental demands.
Abstract: The use of Electronic Commerce (EC)
technologies enables Small Medium Enterprises (SMEs) to improve their efficiency and competitive position. Much of the literature proposes an extensive set of benefits for
organizations that choose to adopt and implement ECommerce
systems. Factors of Business –to-business (B2B)
E-Commerce adoption and implementation have been
extensively investigated. Despite enormous attention given to encourage Small Medium Enterprises (SMEs) to adopt and
implement E-Commerce, little research has been carried out in identifying the factors of Business-to-Consumer ECommerce adoption and implementation for SMEs. To conduct the study, Tornatsky and Fleischer model was adopted
and tested in four SMEs located in Christchurch, New
Zealand. This paper explores the factors that impact the
decision and method of adoption and implementation of ECommerce
systems in automobile industry. Automobile
industry was chosen because the product they deal with i.e.
cars are not a common commodity to be sold online, despite this fact the eCommerce penetration in automobile industry is
high. The factors that promote adoption and implementation of
E-Commerce technologies are discussed, together with the
barriers. This study will help SME owners to effectively
handle the adoption and implementation process and will also
improve the chance of successful E-Commerce
implementation. The implications of the findings for
managers, consultants, and government organizations engaged in promoting E-Commerce adoption and implementation in
small businesses and future research are discussed.
Abstract: The purpose of this paper is to introduce an interactive online case-study library website developed in a national project. The design goal of the website is to provide interactive, enhanced, case-based and online educational resource for educators through the purpose and within the scope of a national project. The ADDIE instructional design model was used in the development of the website for interactive case-based library. This library is developed on a web-based platform, which is important in terms of manageability, accessibility, and updateability of data. Users are able to sort the displayed case-studies by their titles, dates, ratings, view counts, etc. The usability test is used and the expert opinion is taken for the evaluation of the website. This website is a tool to integrate technology into education. It is believed that this website will be beneficial for pre-service and in-service teachers in terms of their professional developments.
Abstract: In this research, a mathematical model for integrated evaluation of green design and green manufacturing processes is presented. To design a product, there can be alternative options to design the detailed components to fulfill the same product requirement. In the design alternative cases, the components of the product can be designed with different materials and detailed specifications. If several design alternative cases are proposed, the different materials and specifications can affect the manufacturing processes. In this paper, a new concept for integrating green design and green manufacturing processes is presented. A green design can be determined based the manufacturing processes of the designed product by evaluating the green criteria including energy usage and environmental impact, in addition to the traditional criteria of manufacturing cost. With this concept, a mathematical model is developed to find the green design and the associated green manufacturing processes. In the mathematical model, the cost items include material cost, manufacturing cost, and green related cost. The green related cost items include energy cost and environmental cost. The objective is to find the decisions of green design and green manufacturing processes to achieve the minimized total cost. In practical applications, the decision-making can be made to select a good green design case and its green manufacturing processes. In this presentation, an example product is illustrated. It shows that the model is practical and useful for integrated evaluation of green design and green manufacturing processes.
Abstract: Perhaps no single issue has been cited as either the root
cause and / or the greatest challenge to the restructured power system then the lack of adequate reliable transmission. Probabilistic transmission planning has become increasingly necessary and important in recent
years. The transmission planning analysis carried out by the authors,
spans a 10-year horizon, taking into consideration a value of 2 % load
increase / year at each consumer. Taking into consideration this increased
load, a probabilistic power flow was carried out, all the system components
being regarded from probabilistic point of view. Several contingencies
have been generated, for assessing the security of the power system. The results have been analyzed and several important conclusions were pointed. The objective is to achieve a network that works without limit violations for all (or most of) scenario realizations. The case study is represented by the IEEE 14 buses test power system.
Abstract: Malware is software which was invented and meant for doing harms on computers. Malware is becoming a significant threat in computer network nowadays. Malware attack is not just only involving financial lost but it can also cause fatal errors which may cost lives in some cases. As new Internet Protocol version 6 (IPv6) emerged, many people believe this protocol could solve most malware propagation issues due to its broader addressing scheme. As IPv6 is still new compares to native IPv4, some transition mechanisms have been introduced to promote smoother migration. Unfortunately, these transition mechanisms allow some malwares to propagate its attack from IPv4 to IPv6 network environment. In this paper, a proof of concept shall be presented in order to show that some existing IPv4 malware detection technique need to be improvised in order to detect malware attack in dual-stack network more efficiently. A testbed of dual-stack network environment has been deployed and some genuine malware have been released to observe their behaviors. The results between these different scenarios will be analyzed and discussed further in term of their behaviors and propagation methods. The results show that malware behave differently on IPv6 from the IPv4 network protocol on the dual-stack network environment. A new detection technique is called for in order to cater this problem in the near future.
Abstract: Carbon fibers are fabricated from different materials,
such as special polyacrylonitrile (PAN) fibers, rayon fibers and pitch.
Among these three groups of materials, PAN fibers are the most
widely used precursor for the manufacture of carbon fibers. The
process of fabrication carbon fibers from special PAN fibers includes
two steps; oxidative stabilization at low temperature and
carbonization at high temperatures in an inert atmosphere. Due to the
high price of raw materials (special PAN fibers), carbon fibers are
still expensive.
In the present work the main goal is making carbon fibers from
low price commercial PAN fibers with modified chemical
compositions. The results show that in case of conducting completes
stabilization process, it is possible to produce carbon fibers with
desirable tensile strength from this type of PAN fibers. To this
matter, thermal characteristics of commercial PAN fibers were
investigated and based upon the obtained results, with some changes
in conventional procedure of stabilization in terms of temperature
and time variables; the desirable conditions of complete stabilization
is achieved.
Abstract: The mountain road slope failures triggered by
earthquake activities and torrential rain namely to create the disaster.
Province Road No. 24 is a main route to the Wutai Township. The area
of the study is located at the mileages between 46K and 47K along the
road. However, the road has been suffered frequent damages as a result
of landslide and slope failures during typhoon seasons. An
understanding of the sliding behaviors in the area appears to be
necessary. Slope failures triggered by earthquake activities and heavy
rainfalls occur frequently. The study is to understand the mechanism
of slope failures and to look for the way to deal with the situation. In
order to achieve these objectives, this paper is based on theoretical and
structural geology data interpretation program to assess the potential
slope sliding behavior. The study showed an intimate relationship
between the landslide behavior of the slopes and the stratum materials,
based on structural geology analysis method to analysis slope stability
and finds the slope safety coefficient to predict the sites of destroyed
layer. According to the case study and parameter analyses results, the
slope mainly slips direction compared to the site located in the
southeast area. Find rainfall to result in the rise of groundwater level is
main reason of the landslide mechanism. Future need to set up
effective horizontal drain at corrective location, that can effective
restrain mountain road slope failures and increase stability of slope.
Abstract: Open urban public spaces comprise an important
element for the development of social, cultural and economic
activities of the population in the modern cities. These spaces are also
considered regulators of the region-s climate conditions, providing
better thermal, visual and auditory conditions which can be optimized
by the application of appropriate strategies of bioclimatic design. The
paper focuses on the analysis and evaluation of the recent unification
of the open spaces in the centre of Xanthi, a medium – size city in
northern Greece, from a bioclimatic perspective, as well as in the
creation of suitable methodology. It is based both on qualitative
observation of the interventions by fieldwork research and
assessment and on quantitative analysis and modeling of the research
area.