Abstract: The thermal control in many systems is widely
accomplished applying mixed convection process due to its low cost,
reliability and easy maintenance. Typical applications include the
aircraft electronic equipment, rotating-disc heat exchangers, turbo
machinery, and nuclear reactors, etc. Natural convection in an inclined
square enclosure heated via wall heater has been studied numerically.
Finite volume method is used for solving momentum and energy
equations in the form of stream function–vorticity. The right and left
walls are kept at a constant temperature, while the other parts are
adiabatic. The range of the inclination angle covers a whole revolution.
The method is validated for a vertical cavity. A general power law
dependence of the Nusselt number with respect to the Rayleigh
number with the coefficient and exponent as functions of the
inclination angle is presented. For a fixed Rayleigh number, the
inclination angle increases or decreases is found.
Abstract: Ionic liquids consisting of a phosphonium cationic
moiety and a saccharinate anion are synthesized and compared with
their precursors, phosphonium chlorides, in reference to their
extraction efficiency towards L-lactic acid. On the base of
measurements of the acid and the water partitioning in the
equilibrium biphasic systems, the molar ratios between acid, water
and ionic liquid are estimated which allows to deduce the lactic acid
extractive pathway. The effect of a salting-out addition that
strengthens hydrophobicity in both phases is studied in view to reveal
the best biphasic system with respect to IL low toxicity and high
extraction efficiency.
Abstract: Catalytic combustion of methane is imperative due to
stability of methane at low temperature. Methane (CH4), therefore,
remains unconverted in vehicle exhausts thereby causing greenhouse
gas GHG emission problem. In this study, heterogeneous catalysts of
palladium with bio-char (2 wt% Pd/Bc) and Al2O3 (2wt% Pd/ Al2O3)
supports were prepared by incipient wetness impregnation and then
subsequently tested for catalytic combustion of CH4. Support-porous
heterogeneous catalytic combustion (HCC) material were selected
based on factors such as surface area, porosity, thermal stability,
thermal conductivity, reactivity with reactants or products, chemical
stability, catalytic activity, and catalyst life. Sustainable and
renewable support-material of bio-mass char derived from palm shell
waste material was compared with those from the conventional
support-porous materials. Kinetic rate of reaction was determined for
combustion of methane on Palladium (Pd) based catalyst with Al2O3
support and bio-char (Bc). Material characterization was done using
TGA, SEM, and BET surface area. The performance test was
accomplished using tubular quartz reactor with gas mixture ratio of
3% methane and 97% air. The methane porous-HCC conversion was
carried out using online gas analyzer connected to the reactor that
performed porous-HCC. BET surface area for prepared 2 wt% Pd/Bc
is smaller than prepared 2wt% Pd/ Al2O3 due to its low porosity
between particles. The order of catalyst activity based on kinetic rate
on reaction of catalysts in low temperature was 2wt%
Pd/Bc>calcined 2wt% Pd/ Al2O3> 2wt% Pd/ Al2O3>calcined 2wt%
Pd/Bc. Hence agro waste material can successfully be utilized as an
inexpensive catalyst support material for enhanced CH4 catalytic
combustion.
Abstract: Most people today are aware that global climate
change is not just a scientific theory but also a fact with worldwide
consequences. Global climate change is due to rapid urbanization,
industrialization, high population growth and current vulnerability of
the climatic condition. Water is becoming scarce as a result of global
climate change. To mitigate the problem arising due to global climate
change and its drought effect, harvesting rainwater from green roofs,
an environmentally-friendly and versatile technology, is becoming
one of the best assessment criteria and gaining attention in Malaysia.
This paper addresses the sustainability of green roofs and examines
the quality of water harvested from green roofs in comparison to
rainwater. The factors that affect the quality of such water, taking
into account, for example, roofing materials, climatic conditions, the
frequency of rainfall frequency and the first flush. A green roof was
installed on the Humid Tropic Centre (HTC) is a place of the study
on monitoring program for urban Stormwater Management Manual
for Malaysia (MSMA), Eco-Hydrological Project in Kuala Lumpur,
and the rainwater was harvested and evaluated on the basis of four
parameters i.e., conductivity, dissolved oxygen (DO), pH and
temperature. These parameters were found to fall between Class I and
Class III of the Interim National Water Quality Standards (INWQS)
and the Water Quality Index (WQI). Some preliminary treatment
such as disinfection and filtration could likely to improve the value of
these parameters to class I. This review paper clearly indicates that
there is a need for more research to address other microbiological and
chemical quality parameters to ensure that the harvested water is
suitable for use potable water for domestic purposes. The change in
all physical, chemical and microbiological parameters with respect to
storage time will be a major focus of future studies in this field.
Abstract: In the past few decades, the field of chemistry
education has grown tremendously and researches indicated that after
traditional chemistry instruction students often lacked deep
conceptual understanding and failed to integrate their ideas into
coherent conceptual framework. For several concepts in chemistry,
students at all levels have demonstrated difficulty in changing their
initial perceptions. Their perceptions are most often wrong and don't
agree with correct scientific concepts. This study explored the
effectiveness of intervention discussion sections for a college general
chemistry course designed to apply research on students
preconceptions, knowledge integration and student explanation.
Three interventions discussions lasting three hours on bond energy
and spontaneity were done tested and intervention (treatment)
students’ performances were compared with that of control group
which did not use the experimental pedagogy. Results indicated that
this instruction which was capable of identifying students'
misconceptions, initial conceptions and integrating those ideas into
class discussion led to enhanced conceptual understanding and better
achievement for the experimental group.
Abstract: Nitrogen fertilizer is the most used and often the most
mismanaged nutrient input. Nitrogen management has tremendous
implications on crop productivity, quality and environmental
stewardship. Sufficient nitrogen is needed to optimum yield and
quality. Soil and in-season plant tissue testing for nitrogen status are
a time consuming and expensive process. Real time sensing of plant
nitrogen status can be a useful tool in managing nitrogen inputs. The
objectives of this project were to assess the reliability of remotely
sensed non-destructive plant nitrogen measurements compared to wet
chemistry data from sampled plant tissue, develop in-season nitrogen
recommendations based on remotely sensed data for improved
nitrogen use efficiency and assess the potential for determining yield
and quality from remotely sensed data. Very good correlations were
observed between early-season remotely sensed crop nitrogen status
and plant nitrogen concentrations and subsequent in-season fertilizer
recommendations. The transmittance/absorbance type meters gave
the most accurate readings. Early in-season fertilizer recommendation
would be to apply 40 kg nitrogen per hectare plus 15 kg nitrogen per
hectare for each unit difference measured with the SPAD meter
between the crop and reference area or 25 kg plus 13 kg per hectare
for each unit difference measured with the CCM 200. Once the crop
was sufficiently fertilized meter readings became inconclusive and
were of no benefit for determining nitrogen status, silage yield and
quality and grain yield and protein.
Abstract: Chemical vapor deposition (CVD) diamond coated
cutting tool has excellent cutting performance, it is the most ideal tool
for the processing of nonferrous metals and alloys, composites,
nonmetallic materials and other difficult-to-machine materials
efficiently and accurately. Depositing CVD diamond coating on the
cemented carbide with high cobalt content can improve its toughness
and strength, therefore, it is very important to research on the
preparation technology and cutting properties of CVD diamond coated
cemented carbide cutting tool with high cobalt content. The
preparation technology of boron-doped diamond (BDD) coating has
been studied and the coated drills were prepared. BDD coating were
deposited on the drills by using the optimized parameters and the SEM
results show that there are no cracks or collapses in the coating.
Cutting tests with the prepared drills against the silumin and aluminum
base printed circuit board (PCB) have been studied. The results show
that the wear amount of the coated drill is small and the machined
surface has a better precision. The coating does not come off during
the test, which shows good adhesion and cutting performance of the
drill.
Abstract: Hybrid bioreactor having both suspended-growth and
attached-growth bacteria is found a novel and excellent bioreactor
system for treating the municipal wastewater containing inhibitory
substrates too. In this reactor a fraction of substrate is used by
suspended biomass and the remaining by attached biomass resulting
in the competition between the two growths for the substrate. The
combination of suspended and attached growth provides the system
with enhanced biomass concentration and sludge age more than those
in ASP. Similar to attached growth system, the hybrid bioreactor
ensures considerable efficiency for treating toxic and refractory
substances in wastewater. For the process design of hybrid bioreactor
a suitable mathematical model is required. Although various
mathematical models were developed on hybrid bioreactor in due
course of time in earlier research works, none of them was found
having a specific simplified solution of the corresponding models and
without having any drawback. To overcome this drawback authors
already developed a simplified mathematical model for process
design of a hybrid bioreactor. The present paper briefly highlights on
the various aspects of process design of an aerobic hybrid bioreactor
for the treatment of municipal wastewater.
Abstract: The purpose of the present work was to develop an
innovative food product with nutritional properties as well as
appealing organoleptic qualities. The product, a jam, was prepared
with the beans’ cooking water combined with fresh apple or carrot,
without the addition of any conservatives. Three different jams were
produced: bean and carrot, bean and apple and bean, apple and
cinnamon. The developed products underwent a sensorial analysis
that revealed that the bean, apple and cinnamon jam was globally
better accepted. However, with this study, the consumers determined
that the bean and carrot jam had the most attractive color and the
bean and apple jam the better consistency. Additionally, it was
possible to analyze the jams for their chemical components, namely
fat, fiber, protein, sugars and antioxidant activity. The obtained
results showed that the bean and carrot jam had the highest lipid
content, while the bean, apple and cinnamon jam had the highest
fiber content, when compared to the other two jams. Regarding the
sugar content, both jams with apple revealed similar sugar values,
which were higher than the sugar content of the bean and carrot jam.
The antioxidant activity was on average 10 mg TE/g.
Abstract: Advances in the use of health care technology have
resulted in increased adverse events (AEs) related to the use of
medical devices. The study focused on the existing reporting systems.
This study was conducted in a tertiary care public sector hospital.
Devices included Syringe infusion pumps, Cardiac monitors, Pulse
oximeters, Ventilators and Defibrillators. A total of 211 respondents
were recruited. Interviews were held with 30 key informants. Medical
records were scrutinized. Relevant statistical tests were used.
Resident doctors reported maximum frequency of AEs, followed
by nurses; and least by consultants. A significant association was
found between the cadre of health care personnel and awareness that
the patients and bystanders have a risk of sustaining AE. Awareness
regarding reporting of AEs was low, and it was generally done
verbally. Other critical findings are discussed in the light of the
barriers to reporting, reasons for non-compliance, recording system,
and so on.
Abstract: We address the integer frequency offset (IFO)
estimation under the influence of the timing offset (TO) in orthogonal
frequency division multiplexing (OFDM) systems. Incorporating the
IFO and TO into the symbol set used to represent the received
OFDM symbol, we investigate the influence of the TO on the IFO,
and then, propose a combining method between two consecutive
OFDM correlations, reducing the influence. The proposed scheme
has almost the same complexity as that of the conventional
schemes, whereas it does not need the TO knowledge contrary to
the conventional schemes. From numerical results it is confirmed
that the proposed scheme is insensitive to the TO, consequently,
yielding an improvement of the IFO estimation performance over
the conventional schemes when the TO exists.
Abstract: This study aimed to identify the alignment of
understanding and assessment practices among secondary school
teachers. The study was carried out using quantitative descriptive
study. The sample consisted of 164 teachers who taught Form 1 and 2
from 11 secondary schools in the district of North Kinta, Perak,
Malaysia. Data were obtained from 164 respondents who answered
Expectation Alignment Understanding and Practices of School
Assessment (PEKDAPS) questionnaire. The data were analysed
using SPSS 17.0+. The Cronbach’s alpha value obtained through
PEKDAPS questionnaire pilot study was 0.86. The results showed
that teachers' performance in PEKDAPS based on the mean value
was less than 3, which means that perfect alignment does not occur
between the understanding and practices of school assessment. Two
major PEKDAPS sub-constructs of articulation across grade and age
and usability of the system were higher than the moderate alignment
of the understanding and practices of school assessment (Min=2.0).
The content focused of PEKDAPs sub-constructs which showed
lower than the moderate alignment of the understanding and practices
of school assessment (Min=2.0). Another two PEKDAPS subconstructs
of transparency and fairness and the pedagogical
implications showed moderate alignment (2.0). The implications of
the study is that teachers need to fully understand the importance of
alignment among components of assessment, learning and teaching
and learning objectives as strategies to achieve quality assessment
process.
Abstract: This paper discusses the design and analysis of a
hybrid PV-Fuel cell energy system destined to power a DC load. The
system is composed of a photovoltaic array, a fuel cell, an
electrolyzer and a hydrogen tank. HOMER software is used in this
study to calculate the optimum capacities of the power system
components that their combination allows an efficient use of solar
resource to cover the hourly load needs. The optimal system sizing
allows establishing the right balance between the daily electrical
energy produced by the power system and the daily electrical energy
consumed by the DC load using a 28 KW PV array, a 7.5 KW fuel
cell, a 40KW electrolyzer and a 270 Kg hydrogen tank. The variation
of powers involved into the DC bus of the hybrid PV-fuel cell system
has been computed and analyzed for each hour over one year: the
output powers of the PV array and the fuel cell, the input power of
the elctrolyzer system and the DC primary load. Equally, the annual
variation of stored hydrogen produced by the electrolyzer has been
assessed. The PV array contributes in the power system with 82%
whereas the fuel cell produces 18%. 38% of the total energy
consumption belongs to the DC primary load while the rest goes to
the electrolyzer.
Abstract: The dissimilar joint between aluminum/titanium
alloys (Al 6082 and Ti G2) were successfully achieved by CO2 laser
welding with a single pass and without filler material using the
overlap joint design. Laser welding parameters ranges combinations
were experimentally determined using Taguchi approach with the
objective of producing welded joint with acceptable welding profile
and high quality of mechanical properties. In this study a joining of
dissimilar Al 6082 / Ti G2 was resulted in three distinct regions
fusion area in the weldment. These regions are studied in terms of its
microstructural characteristics and microhardness which are directly
affecting the welding quality.
The weld metal was mainly composed of martensite alpha prime.
In two different metals in the two different sides of joint HAZ, grain
growth was detected. The microhardness of the joint distribution also
has shown microhardness increasing in the HAZ of two base metals
and a varying microhardness in fusion zone.
Abstract: Urban Search and Rescue (USAR) is a functional
capability that has been developed to allow the United Kingdom Fire
and Rescue Service to deal with ‘major incidents’ primarily involving
structural collapse. The nature of the work undertaken by USAR
means that staying out of a damaged or collapsed building structure is
not usually an option for search and rescue personnel. As a result
there is always a risk that they themselves could become victims. For
this paper, a systematic and investigative review using desk research
was undertaken to explore the role which structural engineering can
play in assisting search and rescue personnel to conduct structural
assessments when in the field. The focus is on how search and rescue
personnel can assess damaged and collapsed building structures, not
just in terms of structural damage that may been countered, but also
in relation to structural stability. Natural disasters, accidental
emergencies, acts of terrorism and other extreme events can vary
significantly in nature and ferocity, and can cause a wide variety of
damage to building structures. It is not possible or, even realistic, to
provide search and rescue personnel with definitive guidelines and
procedures to assess damaged and collapsed building structures as
there are too many variables to consider. However, understanding
what implications damage may have upon the structural stability of a
building structure will enable search and rescue personnel to better judge
and quantify risk from a life-safety standpoint. It is intended that this
will allow search and rescue personnel to make informed decisions
and ensure every effort is made to mitigate risk, so that they
themselves do not become victims.
Abstract: Attributes and methods are the basic contents of an
object-oriented class. The connectivity among these class members
and the relationship between the class and other classes play an
important role in determining the quality of an object-oriented
system. Class cohesion evaluates the degree of relatedness of class
attributes and methods, whereas class coupling refers to the degree to
which a class is related to other classes. Researchers have proposed
several class cohesion and class coupling measures. However, the
correlation between class coupling and class cohesion measures has
not been thoroughly studied. In this paper, using classes of three
open-source Java systems, we empirically investigate the correlation
between several measures of connectivity-based class cohesion and
coupling. Four connectivity-based cohesion measures and eight
coupling measures are considered in the empirical study. The
empirical study results show that class connectivity-based cohesion
and coupling internal quality attributes are inversely correlated. The
strength of the correlation depends highly on the cohesion and
coupling measurement approaches.
Abstract: This article focuses on the issue of airport emergency
plans, which are documents describing reactions to events with
impact on aviation safety or aviation security. The article specifically
focuses on the use and creation of emergency plans, where could be
found a number of disagreements between different stakeholders, for
which the airport emergency plan applies. Those are the friction
surfaces of interfaces, which is necessary to identify and ensure them
smooth process to avoid dangerous situations or delay.
Abstract: Contemporary city is a subject to rapid economic and
social changes. Therefore, it requires an active policy designed to
meet the diverse needs of their residents, build competitive position
and capacity to compete with other cities. Competitiveness of cities
depends largely on their resources but also to a large extent, on the
policies and performance of local authorities. Cooperation with social
sector also plays an important role, as it affects the use of resources
and builds an advantage over other cities.
The subject of this article is city's contemporary problems of
development with particular emphasis on central areas. This issue is a
starting point for reflection on the process of urban regeneration in
medium size cities in Poland, as well as cooperation between various
actors and their roles in the revitalization processes of Polish cities'
centers.
Abstract: Offering a Product-Service System (PSS) is a
well-accepted strategy that companies may adopt to provide a set of
systemic solutions to customers. PSSs were initially provided in a
simple form but now take diversified and complex forms involving
multiple services, products and technologies. With the growing
interest in the PSS, frameworks for the PSS development have been
introduced by many researchers. However, most of the existing
frameworks fail to examine various relations existing in a complex
PSS. Since designing a complex PSS involves full integration of
multiple products and services, it is essential to identify not only
product-service relations but also product-product/ service-service
relations. It is also equally important to specify how they are related
for better understanding of the system. Moreover, as customers tend to
view their purchase from a more holistic perspective, a PSS should be
developed based on the whole system’s requirements, rather than
focusing only on the product requirements or service requirements.
Thus, we propose a framework to develop a complex PSS that is
coordinated fully with the requirements of both worlds. Specifically,
our approach adopts a multi-domain matrix (MDM). A MDM
identifies not only inter-domain relations but also intra-domain
relations so that it helps to design a PSS that includes highly desired
and closely related core functions/ features. Also, various dependency
types and rating schemes proposed in our approach would help the
integration process.
Abstract: Pulmonary Function Tests are important non-invasive
diagnostic tests to assess respiratory impairments and provides
quantifiable measures of lung function. Spirometry is the most
frequently used measure of lung function and plays an essential role
in the diagnosis and management of pulmonary diseases. However,
the test requires considerable patient effort and cooperation,
markedly related to the age of patients resulting in incomplete data
sets. This paper presents, a nonlinear model built using Multivariate
adaptive regression splines and Random forest regression model to
predict the missing spirometric features. Random forest based feature
selection is used to enhance both the generalization capability and the
model interpretability. In the present study, flow-volume data are
recorded for N= 198 subjects. The ranked order of feature importance
index calculated by the random forests model shows that the
spirometric features FVC, FEF25, PEF, FEF25-75, FEF50 and the
demographic parameter height are the important descriptors. A
comparison of performance assessment of both models prove that, the
prediction ability of MARS with the `top two ranked features namely
the FVC and FEF25 is higher, yielding a model fit of R2= 0.96 and
R2= 0.99 for normal and abnormal subjects. The Root Mean Square
Error analysis of the RF model and the MARS model also shows that
the latter is capable of predicting the missing values of FEV1 with a
notably lower error value of 0.0191 (normal subjects) and 0.0106
(abnormal subjects) with the aforementioned input features. It is
concluded that combining feature selection with a prediction model
provides a minimum subset of predominant features to train the
model, as well as yielding better prediction performance. This
analysis can assist clinicians with a intelligence support system in the
medical diagnosis and improvement of clinical care.