Abstract: High double excitation of two-electron atoms has been
investigated using hyperpherical coordinates within a modified
adiabatic expansion technique. This modification creates a novel
fictitious force leading to a spontaneous exchange symmetry breaking
at high double excitation. The Pauli principle must therefore be
regarded as approximation valid only at low excitation energy.
Threshold electron scattering from high Rydberg states shows an
unexpected time reversal symmetry breaking. At threshold for double
escape we discover a broad (few eV) Cooper pair.
Abstract: Ultrasonic metal welding has been the subject of ongoing research and development, most recently concentrating on metal joining in miniature devices, for example to allow solder-free wire bonding. As well as at the small scale, there are also opportunities to research the joining of thicker sheet metals and to widen the range of similar and dissimilar materials that can be successfully joined using this technology. This study presents the design, characterisation and test of a lateral-drive ultrasonic metal spot welding device. The ultrasonic metal spot welding horn is modelled using finite element analysis (FEA) and its vibration behaviour is characterised experimentally to ensure ultrasonic energy is delivered effectively to the weld coupon. The welding stack and fixtures are then designed and mounted on a test machine to allow a series of experiments to be conducted for various welding and ultrasonic parameters. Weld strength is subsequently analysed using tensile-shear tests. The results show how the weld strength is particularly sensitive to the combination of clamping force and ultrasonic vibration amplitude of the welding tip, but there are optimal combinations of these and also limits that must be clearly identified.
Abstract: Centrifugal-casting machine is used in manufacturing
special machine components like multi-layer journal bearing used in
all internal combustion engine, steam, gas turbine and air craft turboengine
where isotropic properties and high precisions are desired.
Moreover, this machine can be used in manufacturing thin wall hightech
machine components like cylinder liners and piston rings of IC
engine and other machine parts like sleeves, and bushes. Heavy-duty
machine component like railway wheel can also be prepared by
centrifugal casting. A lot of technological developments are required
in casting process for production of good casted machine body and
machine parts. Usually defects like blowholes, surface roughness,
chilled surface etc. are found in sand casted machine parts. But these
can be removed by centrifugal casting machine using rotating
metallic die. Moreover, die rotation, its temperature control, and good
pouring practice can contribute to the quality of casting because of
the fact that the soundness of a casting in large part depends upon
how the metal enters into the mold or dies and solidifies. Poor
pouring practice leads to variety of casting defects such as
temperature loss, low quality casting, excessive turbulence, over
pouring etc. Besides these, handling of molten metal is very
unsecured and dangerous for the workers. In order to get rid of all
these problems, the need of an automatic pouring device arises. In
this research work, a robot assisted pouring device and a centrifugal
casting machine are designed, developed constructed and tested
experimentally which are found to work satisfactorily. The robot
assisted pouring device is further modified and developed for using it
in actual metal casting process. Lot of settings and tests are required
to control the system and ultimately it can be used in automation of
centrifugal casting machine to produce high-tech machine parts with
desired precision.
Abstract: In this paper, autonomous performance of a small
manufactured unmanned helicopter is tried to be increased. For this
purpose, a small unmanned helicopter is manufactured in Erciyes
University, Faculty of Aeronautics and Astronautics. It is called as
ZANKA-Heli-I. For performance maximization, autopilot parameters
are determined via minimizing a cost function consisting of flight
performance parameters such as settling time, rise time, overshoot
during trajectory tracking. For this purpose, a stochastic optimization
method named as simultaneous perturbation stochastic approximation
is benefited. Using this approach, considerable autonomous
performance increase (around %23) is obtained.
Abstract: In this paper, it is aimed to improve autonomous flight
performance of a load-carrying (payload: 3 kg and total: 6kg)
unmanned aerial vehicle (UAV) through active wing and horizontal
tail active morphing and also integrated autopilot system parameters
(i.e. P, I, D gains) and UAV parameters (i.e. extension ratios of wing
and horizontal tail during flight) design. For this purpose, a loadcarrying
UAV (i.e. ZANKA-II) is manufactured in Erciyes
University, College of Aviation, Model Aircraft Laboratory is
benefited. Optimum values of UAV parameters and autopilot
parameters are obtained using a stochastic optimization method.
Using this approach autonomous flight performance of UAV is
substantially improved and also in some adverse weather conditions
an opportunity for safe flight is satisfied. Active morphing and
integrated design approach gives confidence, high performance and
easy-utility request of UAV users.
Abstract: The boundary layer separation and new active flow control of a NACA 0025 airfoil were studied experimentally. This new flow control is sometimes known as a co-flow jet (cfj) airfoil. This paper presents the fluctuating velocity in a wall jet over the co-flow jet airfoil subjected to an adverse pressure gradient and a curved surface. In these results, the fluctuating velocity at the inner part increasing by increased the angle of attack up to 12o and this has due to the jet energized, while the angle of attack 20o has different. The airfoil cord based Reynolds number has 105.
Abstract: A composite material with carbon fiber and polymer
matrix has been used as adherent for manufacturing adhesive joints.
In order to evaluate different fiber orientations on joint performance,
the adherents with the 0°, ±15°, ±30°, ±45° fiber orientations were
used in the single lap joint configuration. The joints with an overlap
length of 25 mm were prepared according to the ASTM 1002
specifications and subjected to tensile loadings. The structural
adhesive used was a two-part epoxy to be cured at 70°C for an hour.
First, mechanical behaviors of the adherents were measured using
three point bending test. In the test, considerations were given to
stress to failure and elastic modulus. The results were compared with
theoretical ones using rule of mixture. Then, the joints were
manufactured in a specially prepared jig, after a proper surface
preparation. Experimental results showed that the fiber orientations
of the adherents affected the joint performance considerably; the
joints with ±45° adherents experienced the worst shear strength, half
of those with 0° adherents, and in general, there was a great
relationship between the fiber orientations and failure mechanisms.
Delamination problems were observed for many joints, which were
thought to be due to peel effects at the ends of the overlap. It was
proved that the surface preparation applied to the adherent surface
was adequate. For further explanation of the results, a numerical
work should be carried out using a possible non-linear analysis.
Abstract: This paper investigates the application of metallic
coatings on high fiber volume fraction carbon/epoxy polymer matrix
composites. For the grip of the metallic layer, a method of modifying
the surface of the composite by introducing a mixture of copper and
steel powder (filler powders) which can reduce the impact of thermal
spray particles. The powder was introduced to the surface at the time
of the forming. Arc spray was used to project the zinc coating layer.
The substrate was grit blasted to avoid poor adherence. The porosity, microstructure, and morphology of layers are
characterized by optical microscopy, SEM and image analysis. The
samples were studied also in terms of hardness and erosion resistance.
This investigation did not reveal any visible evidence damage to the
substrates. The hardness of zinc layer was about 25.94 MPa and the
porosity was around (∼6.70%). The erosion test showed that the zinc
coating improves the resistance to erosion. Based on the results
obtained, we can conclude that thermal spraying allows the production
of protective coating on PMC. Zinc coating has been identified as a
compatible material with the substrate. The filler powders layer
protects the substrate from the impact of hot particles and allows
avoiding the rupture of brittle carbon fibers.
Abstract: The recent instability in economy was found to be
influencing the situation in Malaysia whether directly or indirectly.
Taking that into consideration, the government needs to find the best
approach to balance its citizen’s socio-economic strata level urgently.
Through education platform is among the efforts planned and acted
upon for the purpose of balancing the effects of the influence,
through the exposure of social entrepreneurial activity towards youth
especially those in higher institution level. Armed with knowledge
and skills that they gained, with the support by entrepreneurial
culture and environment while in campus; indirectly, the students will
lean more on making social entrepreneurship as a career option when
they graduate. Following the issues of marketability and workability
of current graduates that are becoming dire, research involving how
far the willingness of student to create social innovation that
contribute to the society without focusing solely on personal gain is
relevant enough to be conducted. With that, this research is
conducted with the purpose of identifying the level of entrepreneurial
intention and social entrepreneurship among higher institution
students in Malaysia. Stratified random sampling involves 355
undergraduate students from five public universities had been made
as research respondents and data were collected through surveys. The
data was then analyzed descriptively using min score and standard
deviation. The study found that the entrepreneurial intention of higher
education students are on moderate level, however it is the contrary
for social entrepreneurship activities, where it was shown on a high
level. This means that while the students only have moderate level of
willingness to be a social entrepreneur, they are very committed to
created social innovation through the social entrepreneurship
activities conducted. The implication from this study can be
contributed towards the higher institution authorities in prediction the
tendency of student in becoming social entrepreneurs. Thus, the
opportunities and facilities for realizing the courses related to social
entrepreneurship must be created expansively so that the vision of
creating as many social entrepreneurs as possible can be achieved.
Abstract: This paper presents the design and analysis of Liquid Crystal (LC) based tunable reflectarray antenna with slot embedded patch element configurations within X-band frequency range. The slots are shown to modify the surface current distribution on the patch element of reflectarray which causes the resonant patch element to provide different resonant frequencies depending on the slot dimensions. The simulated results are supported and verified by waveguide scattering parameter measurements of different reflectarray unit cells. Different rectangular slots on patch element have been fabricated and a change in resonant frequency from 10.46GHz to 8.78GHz has been demonstrated as the width of the rectangular slot is varied from 0.2W to 0.6W. The rectangular slot in the center of the patch element has also been utilized for the frequency tunable reflectarray antenna design based on K-15 Nematic LC. For the active reflectarray antenna design, a frequency tunability of 1.2% from 10GHz to 9.88GHz has been demonstrated with a dynamic phase range of 103° provided by the measured scattering parameter results. Time consumed by liquid crystals for reconfiguration, which is one of the drawback of LC based design, has also been disused in this paper.
Abstract: Intellectual capital is one of the most valuable and
important parts of the intangible assets of enterprises especially in
knowledge-based enterprises. With respect to increasing gap between
the market value and the book value of the companies, intellectual
capital is one of the components that can be placed in this gap. This
paper uses the value added efficiency of the three components,
capital employed, human capital and structural capital, to measure the
intellectual capital efficiency of Iranian industries groups, listed in
the Tehran Stock Exchange (TSE), using a 8 years period data set
from 2005 to 2012. In order to analyze the effect of intellectual
capital on the market-to-book value ratio of the companies, the data
set was divided into 10 industries, Banking, Pharmaceutical, Metals
& Mineral Nonmetallic, Food, Computer, Building, Investments,
Chemical, Cement and Automotive, and the panel data method was
applied to estimating pooled OLS. The results exhibited that value
added of capital employed has a positive significant relation with
increasing market value in the industries, Banking, Metals & Mineral
Nonmetallic, Food, Computer, Chemical and Cement, and also,
showed that value added efficiency of structural capital has a positive
significant relation with increasing market value in the Banking,
Pharmaceutical and Computer industries groups. The results of the
value added showed a negative relation with the Banking and
Pharmaceutical industries groups and a positive relation with
computer and Automotive industries groups. Among the studied
industries, computer industry has placed the widest gap between the
market value and book value in its intellectual capital.
Abstract: This paper investigates the thermo-electric effects
around the crack and notch tips under the electric current load. The
research methods include the finite element analysis and thermal
imaging experiment. The finite element solutions show that the electric
current density field concentrates at the crack tip. Due to the Joule
heating, this electric concentration causes the hot spot at the tip zone.
From numerical and experimental results, this hot spot is identified.
The temperature of the hot spot is affected by the electric load,
operation time and geometry of the sample.
Abstract: Dan C. Lortie’s Schoolteacher: A sociological study is
one of the best works on the sociology of teaching since W. Waller’s
classic study. It is a book worthy of review. Following the tradition of
symbolic interactionists, Lortie demonstrated the qualities who studied
the occupation of teaching. Using several methods to gather effective
data, Lortie has portrayed the ethos of the teaching profession.
Therefore, the work is an important book on the teaching profession
and teacher culture. Though outstanding, Lortie’s work is also flawed
in that his perspectives and methodology were adopted largely from
symbolic interactionism. First, Lortie in his work analyzed many
points regarding teacher culture; for example, he was interested in
exploring “sentiment,” “cathexis,” and “ethos.” Thus, he was more a
psychologist than a sociologist. Second, symbolic interactionism led
him to discern the teacher culture from a micro view, thereby missing
the structural aspects. For example, he did not fully discuss the issue of
gender and he ignored the issue of race. Finally, following the
qualitative sociological tradition, Lortie employed many qualitative
methods to gather data but only foucused on obtaining and presenting
interview data. Moreover, he used measurement methods that were too
simplistic for analyzing quantitative data fully.
Abstract: The Hall Coefficient (HC) and the Magnetoresistance (MR) have been studied in two-dimensional systems. The HC and the MR in Rectangular Quantum Wire (RQW) subjected to a crossed DC electric field and magnetic field in the presence of a Strong Electromagnetic Wave (EMW) characterized by electric field are studied in this work. Using the quantum kinetic equation for electrons interacting with optical phonons, we obtain the analytic expressions for the HC and the MR with a dependence on magnetic field, EMW frequency, temperatures of systems and the length characteristic parameters of RQW. These expressions are different from those obtained for bulk semiconductors and cylindrical quantum wires. The analytical results are applied to GaAs/GaAs/Al. For this material, MR depends on the ratio of the EMW frequency to the cyclotron frequency. Indeed, MR reaches a minimum at the ratio 5/4, and when this ratio increases, it tends towards a saturation value. The HC can take negative or positive values. Each curve has one maximum and one minimum. When magnetic field increases, the HC is negative, achieves a minimum value and then increases suddenly to a maximum with a positive value. This phenomenon differs from the one observed in cylindrical quantum wire, which does not have maximum and minimum values.
Abstract: The source of the jet noise is generated by rocket exhaust plume during rocket engine testing. A domain decomposition approach is applied to the jet noise prediction in this paper. The aerodynamic noise coupling is based on the splitting into acoustic sources generation and sound propagation in separate physical domains. Large Eddy Simulation (LES) is used to simulate the supersonic jet flow. Based on the simulation results of the flow-fields, the jet noise distribution of the sound pressure level is obtained by applying the Ffowcs Williams-Hawkings (FW-H) acoustics equation and Fourier transform. The calculation results show that the complex structures of expansion waves, compression waves and the turbulent boundary layer could occur due to the strong interaction between the gas jet and the ambient air. In addition, the jet core region, the shock cell and the sound pressure level of the gas jet increase with the nozzle size increasing. Importantly, the numerical simulation results of the far-field sound are in good agreement with the experimental measurements in directivity.
Abstract: Open jet testing is a valuable testing technique which
provides the desired results with reasonable accuracy. It has been
used in past for the airships and now has recently been applied for the
hybrid ones, having more non-buoyant force coming from the wings,
empennage and the fuselage. In the present review work, an effort
has been done to review the challenges involved in open jet testing.
In order to shed light on the application of this technique, the
experimental results of two different configurations are presented.
Although, the aerodynamic results of such vehicles are unique to its
own design; however, it will provide a starting point for planning any
future testing. Few important testing areas which need more attention
are also highlighted. Most of the hybrid buoyant aerial vehicles are
unconventional in shape and there experimental data is generated,
which is unique to its own design.
Abstract: Landfill leachates contain a number of persistent pollutants, including heavy metals. They have the ability to spread in ecosystems and accumulate in fish which most of them are classified as top-consumers of trophic chains. Fish are freely swimming organisms; but perhaps, due to their species-specific ecological and behavioral properties, they often prefer the most suitable biotopes and therefore, did not avoid harmful substances or environments. That is why it is necessary to evaluate the persistent pollutant dispersion in hydroecosystem using fish tissue metal concentration. In hydroecosystems of hybrid type (e.g. river-pond-river) the distance from the pollution source could be a perfect indicator of such a kind of metal distribution. The studies were carried out in the Kairiai landfill neighboring hybrid-type ecosystem which is located 5 km east of the Šiauliai City. Fish tissue (gills, liver, and muscle) metal concentration measurements were performed on two types of ecologically-different fishes according to their feeding characteristics: benthophagous (Gibel carp, roach) and predatory (Northern pike, perch). A number of mathematical models (linear, non-linear, using log and other transformations) have been applied in order to identify the most satisfactorily description of the interdependence between fish tissue metal concentration and the distance from the pollution source. However, the only one log-multiple regression model revealed the pattern that the distance from the pollution source is closely and positively correlated with metal concentration in all predatory fish tissues studied (gills, liver, and muscle).
Abstract: The process of human resources management in the structures of corporate groups demonstrates certain specificity, resulting from the division of decision-making and executive competencies, which occurs within these structures between a parent company and its subsidiaries. The subprocess of employee assessment is considered crucial, since it provides information for the implementation of personnel function. The empirical studies conducted in corporate groups, within which at least one company is located in Poland, confirmed the critical significance of employee assessment systems in the process of human resources management in corporate groups. Parent companies, most often, retain their decision-making authority within the framework of the discussed process and introduce uniform employee assessment and personnel controlling systems to subsidiary companies. However, the instruments for employee assessment applied in corporate groups do not present such specificity.
Abstract: This paper describes a simple way to control the speed
of PMBLDC motor using Fuzzy logic control method. In the
conventional PI controller the performance of the motor system is
simulated and the speed is regulated by using PI controller. These
methods used to improve the performance of PMSM drives, but in
some cases at different operating conditions when the dynamics of
the system also vary over time and it can change the reference speed,
parameter variations and the load disturbance. The simulation is
powered with the MATLAB program to get a reliable and flexible
simulation. In order to highlight the effectiveness of the speed control
method the FLC method is used. The proposed method targeted in
achieving the improved dynamic performance and avoids the
variations of the motor drive. This drive has high accuracy, robust
operation from near zero to high speed. The effectiveness and
flexibility of the individual techniques of the speed control method
will be thoroughly discussed for merits and demerits and finally
verified through simulation and experimental results for comparative
analysis.
Abstract: This paper discusses the applicability of the numerical model for a damage prediction method of the accidental hydrogen explosion occurring in a hydrogen facility. The numerical model was based on an unstructured finite volume method (FVM) code “NuFD/FrontFlowRed”. For simulating unsteady turbulent combustion of leaked hydrogen gas, a combination of Large Eddy Simulation (LES) and a combustion model were used. The combustion model was based on a two scalar flamelet approach, where a G-equation model and a conserved scalar model expressed a propagation of premixed flame surface and a diffusion combustion process, respectively. For validation of this numerical model, we have simulated the previous two types of hydrogen explosion tests. One is open-space explosion test, and the source was a prismatic 5.27 m3 volume with 30% of hydrogen-air mixture. A reinforced concrete wall was set 4 m away from the front surface of the source. The source was ignited at the bottom center by a spark. The other is vented enclosure explosion test, and the chamber was 4.6 m × 4.6 m × 3.0 m with a vent opening on one side. Vent area of 5.4 m2 was used. Test was performed with ignition at the center of the wall opposite the vent. Hydrogen-air mixtures with hydrogen concentrations close to 18% vol. were used in the tests. The results from the numerical simulations are compared with the previous experimental data for the accuracy of the numerical model, and we have verified that the simulated overpressures and flame time-of-arrival data were in good agreement with the results of the previous two explosion tests.