Abstract: In recent years, most of the regions in the world are
exposed to degradation and erosion caused by increasing
population and over use of land resources. The understanding of
the most important factors on soil erosion and sediment yield are
the main keys for decision making and planning. In this study, the
sediment yield and soil erosion were estimated and the priority of
different soil erosion factors used in the MPSIAC method of soil
erosion estimation is evaluated in AliAbad watershed in southwest
of Isfahan Province, Iran. Different information layers of the
parameters were created using a GIS technique. Then, a
multivariate procedure was applied to estimate sediment yield and
to find the most important factors of soil erosion in the model. The
results showed that land use, geology, land and soil cover are the
most important factors describing the soil erosion estimated by
MPSIAC model.
Abstract: In process control applications, above 90% of the
controllers are of PID type. This paper proposed a robust PI
controller with fractional-order integrator. The PI parameters were
obtained using classical Ziegler-Nichols rules but enhanced with the
application of error filter cascaded to the fractional-order PI. The
controller was applied on steam temperature process that was
described by FOPDT transfer function. The process can be classified
as lag dominating process with very small relative dead-time. The
proposed control scheme was compared with other PI controller
tuned using Ziegler-Nichols and AMIGO rules. Other PI controller
with fractional-order integrator known as F-MIGO was also
considered. All the controllers were subjected to set point change and
load disturbance tests. The performance was measured using Integral
of Squared Error (ISE) and Integral of Control Signal (ICO). The
proposed controller produced best performance for all the tests with
the least ISE index.
Abstract: The characterization of κ-carrageenan could provide a
better understanding of its functions in biological, medical and
industrial applications. Chemical and physical analyses of
carrageenan from seaweeds, Euchema cottonii L., were done to offer
information on its properties and the effects of Co-60 γ-irradiation on
its thermochemical characteristics. The structural and morphological
characteristics of κ-carrageenan were determined using scanning
electron microscopy (SEM) while the composition, molecular weight
and thermal properties were determined using attenuated total
reflectance Fourier transform infrared spectroscopy (ATR-FTIR), gel
permeation chromatography (GPC), thermal gravimetric analysis
(TGA) and differential scanning calorimetry (DSC). Further chemical
analysis was done using hydrogen-1 nuclear magnetic resonance (1H
NMR) and functional characteristics in terms of biocompatibility
were evaluated using cytotoxicity test.
Abstract: This paper is concerned with the application of the vision control algorithm for robot's point placement task in discontinuous trajectory caused by obstacle. The presented vision control algorithm consists of four models, which are the robot kinematic model, vision system model, parameters estimation model, and robot joint angle estimation model.When the robot moves toward a target along discontinuous trajectory, several types of obstacles appear in two obstacle regions. Then, this study is to investigate how these changes will affect the presented vision control algorithm.Thus, the practicality of the vision control algorithm is demonstrated experimentally by performing the robot's point placement task in discontinuous trajectory by obstacle.
Abstract: In this paper we present a way of controlling the
concurrent access to data in a distributed application using the
Pessimistic Offline Lock design pattern. In our case, the application
processes a complex entity, which contains in a hierarchical structure
different other entities (objects). It will be shown how the complex
entity and the contained entities must be locked in order to control
the concurrent access to data.
Abstract: Raisin Concentrate (RC) are the most important
products obtained in the raisin processing industries. These RC
products are now used to make the syrups, drinks and confectionery
productions and introduced as natural substitute for sugar in food
applications. Iran is a one of the biggest raisin exporter in the world
but unfortunately despite a good raw material, no serious effort to
extract the RC has been taken in Iran. Therefore, in this paper, we
determined and analyzed affected parameters on extracting RC
process and then optimizing these parameters for design the
extracting RC process in two types of raisin (round and long)
produced in Khorasan region. Two levels of solvent (1:1 and 2:1),
three levels of extraction temperature (60°C, 70°C and 80°C), and
three levels of concentration temperature (50°C, 60°C and 70°C)
were the treatments. Finally physicochemical characteristics of the
obtained concentrate such as color, viscosity, percentage of reduction
sugar, acidity and the microbial tests (mould and yeast) were
counted. The analysis was performed on the basis of factorial in the
form of completely randomized design (CRD) and Duncan's multiple
range test (DMRT) was used for the comparison of the means.
Statistical analysis of results showed that optimal conditions for
production of concentrate is round raisins when the solvent ratio was
2:1 with extraction temperature of 60°C and then concentration
temperature of 50°C. Round raisin is cheaper than the long one, and
it is more economical to concentrate production. Furthermore, round
raisin has more aromas and the less color degree with increasing the
temperature of concentration and extraction. Finally, according to
mentioned factors the concentrate of round raisin is recommended.
Abstract: A mathematical model for the hydrodynamics of a
surface water treatment pilot plant was developed and validated by
the determination of the residence time distribution (RTD) for the
main equipments of the unit. The well known models of ideal/real
mixing, ideal displacement (plug flow) and (one-dimensional axial)
dispersion model were combined in order to identify the structure
that gives the best fitting of the experimental data for each equipment
of the pilot plant. RTD experimental results have shown that pilot
plant hydrodynamics can be quite well approximated by a
combination of simple mathematical models, structure which is
suitable for engineering applications. Validated hydrodynamic
models will be further used in the evaluation and selection of the
most suitable coagulation-flocculation reagents, optimum operating
conditions (injection point, reaction times, etc.), in order to improve
the quality of the drinking water.
Abstract: Lossless compression schemes with secure
transmission play a key role in telemedicine applications that helps in
accurate diagnosis and research. Traditional cryptographic algorithms
for data security are not fast enough to process vast amount of data.
Hence a novel Secured lossless compression approach proposed in
this paper is based on reversible integer wavelet transform, EZW
algorithm, new modified runlength coding for character
representation and selective bit scrambling. The use of the lifting
scheme allows generating truly lossless integer-to-integer wavelet
transforms. Images are compressed/decompressed by well-known
EZW algorithm. The proposed modified runlength coding greatly
improves the compression performance and also increases the
security level. This work employs scrambling method which is fast,
simple to implement and it provides security. Lossless compression
ratios and distortion performance of this proposed method are found
to be better than other lossless techniques.
Abstract: An array of piezoelectric micro actuators can be used
for radiation of an ultrasonic carrier signal modulated in amplitude
with an acoustic signal, which yields audio frequency applications as
the air acts as a self-demodulating medium. This application is
known as the parametric array. We propose a parametric array with
array elements based on existing piezoelectric micro ultrasonic
transducer (pMUT) design techniques. In order to reach enough
acoustic output power at a desired operating frequency, a proper ratio
between number of array elements and array size needs to be used,
with an array total area of the order of one cm square. The
transducers presented are characterized via impedance, admittance,
noise figure, transducer gain and frequency responses.
Abstract: This paper will present the initial findings of a
research into distributed computer rendering. The goal of the
research is to create a distributed computer system capable of
rendering a 3D model into an MPEG-4 stream. This paper outlines
the initial design, software architecture and hardware setup for the
system.
Distributed computing means designing and implementing
programs that run on two or more interconnected computing systems.
Distributed computing is often used to speed up the rendering of
graphical imaging. Distributed computing systems are used to
generate images for movies, games and simulations.
A topic of interest is the application of distributed computing to
the MPEG-4 standard. During the course of the research, a
distributed system will be created that can render a 3D model into an
MPEG-4 stream. It is expected that applying distributed computing
principals will speed up rendering, thus improving the usefulness and
efficiency of the MPEG-4 standard
Abstract: This paper presents a highly efficient algorithm for detecting and tracking humans and objects in video surveillance sequences. Mean shift clustering is applied on backgrounddifferenced image sequences. For efficiency, all calculations are performed on integral images. Novel corresponding exponential integral kernels are introduced to allow the application of nonuniform kernels for clustering, which dramatically increases robustness without giving up the efficiency of the integral data structures. Experimental results demonstrating the power of this approach are presented.
Abstract: The urban centers within northeastern Brazil are
mainly influenced by the intense rainfalls, which can occur after long
periods of drought, when flood events can be observed during such
events. Thus, this paper aims to study the rainfall frequencies in such
region through the wavelet transform. An application of wavelet
analysis is done with long time series of the total monthly rainfall
amount at the capital cities of northeastern Brazil. The main
frequency components in the time series are studied by the global
wavelet spectrum and the modulation in separated periodicity bands
were done in order to extract additional information, e.g., the 8 and
16 months band was examined by an average of all scales, giving a
measure of the average annual variance versus time, where the
periods with low or high variance could be identified. The important
increases were identified in the average variance for some periods,
e.g. 1947 to 1952 at Teresina city, which can be considered as high
wet periods. Although, the precipitation in those sites showed similar
global wavelet spectra, the wavelet spectra revealed particular
features. This study can be considered an important tool for time
series analysis, which can help the studies concerning flood control,
mainly when they are applied together with rainfall-runoff
simulations.
Abstract: One of the most basic functions of control engineers is
tuning of controllers. There are always several process loops in the
plant necessitate of tuning. The auto tuned Proportional Integral
Derivative (PID) Controllers are designed for applications where
large load changes are expected or the need for extreme accuracy and
fast response time exists. The algorithm presented in this paper is
used for the tuning PID controller to obtain its parameters with a
minimum computing complexity. It requires continuous analysis of
variation in few parameters, and let the program to do the plant test
and calculate the controller parameters to adjust and optimize the
variables for the best performance. The algorithm developed needs
less time as compared to a normal step response test for continuous
tuning of the PID through gain scheduling.
Abstract: Set covering problem is a classical problem in
computer science and complexity theory. It has many applications,
such as airline crew scheduling problem, facilities location problem,
vehicle routing, assignment problem, etc. In this paper, three
different techniques are applied to solve set covering problem.
Firstly, a mathematical model of set covering problem is introduced
and solved by using optimization solver, LINGO. Secondly, the
Genetic Algorithm Toolbox available in MATLAB is used to solve
set covering problem. And lastly, an ant colony optimization method
is programmed in MATLAB programming language. Results
obtained from these methods are presented in tables. In order to
assess the performance of the techniques used in this project, the
benchmark problems available in open literature are used.
Abstract: Existing image-based virtual reality applications
allow users to view image-based 3D virtual environment in a more
interactive manner. User could “walkthrough"; looks left, right, up
and down and even zoom into objects in these virtual worlds of
images. However what the user sees during a “zoom in" is just a
close-up view of the same image which was taken from a distant.
Thus, this does not give the user an accurate view of the object from
the actual distance. In this paper, a simple technique for zooming in
an object in a virtual scene is presented. The technique is based on
the 'hotspot' concept in existing application. Instead of navigation
between two different locations, the hotspots are used to focus into
an object in the scene. For each object, several hotspots are created.
A different picture is taken for each hotspot. Each consecutive
hotspot created will take the user closer to the object. This will
provide the user with a correct of view of the object based on his
proximity to the object. Implementation issues and the relevance of
this technique in potential application areas are highlighted.
Abstract: This research presents a fuzzy multi-objective model
for a machine selection problem in a flexible manufacturing system
of a tire company. Two main objectives are minimization of an
average machine error and minimization of the total setup time.
Conventionally, the working team uses trial and error in selecting a
pressing machine for each task due to the complexity and constraints
of the problem. So, both objectives may not satisfy. Moreover, trial
and error takes a lot of time to get the final decision. Therefore, in
this research preemptive fuzzy goal programming model is developed
for solving this multi-objective problem. The proposed model can
obtain the appropriate results that the Decision Making (DM) is
satisfied for both objectives. Besides, alternative choice can be easily
generated by varying the satisfaction level. Additionally, decision
time can be reduced by using the model, which includes all
constraints of the system to generate the solutions. A numerical
example is also illustrated to show the effectiveness of the proposed
model.
Abstract: This paper presents work characterizing finite element
performance boundaries within which live, interactive finite element
modeling is feasible on current and emerging systems. These results
are based on wide-ranging tests performed using a prototype finite
element program implemented specifically for this study, thereby enabling
the unified investigation of numerous direct and iterative solver
strategies and implementations in a variety of modeling contexts.
The results are intended to be useful for researchers interested in
interactive analysis by providing baseline performance estimates, to
give guidance in matching solution strategies to problem domains,
and to spur further work addressing the challenge of extending the
present boundaries.
Abstract: Rutting is one of the major load-related distresses in airport flexible pavements. Rutting in paving materials develop gradually with an increasing number of load applications, usually appearing as longitudinal depressions in the wheel paths and it may be accompanied by small upheavals to the sides. Significant research has been conducted to determine the factors which affect rutting and how they can be controlled. Using the experimental design concepts, a series of tests can be conducted while varying levels of different parameters, which could be the cause for rutting in airport flexible pavements. If proper experimental design is done, the results obtained from these tests can give a better insight into the causes of rutting and the presence of interactions and synergisms among the system variables which have influence on rutting. Although traditionally, laboratory experiments are conducted in a controlled fashion to understand the statistical interaction of variables in such situations, this study is an attempt to identify the critical system variables influencing airport flexible pavement rut depth from a statistical DoE perspective using real field data from a full-scale test facility. The test results do strongly indicate that the response (rut depth) has too much noise in it and it would not allow determination of a good model. From a statistical DoE perspective, two major changes proposed for this experiment are: (1) actual replication of the tests is definitely required, (2) nuisance variables need to be identified and blocked properly. Further investigation is necessary to determine possible sources of noise in the experiment.
Abstract: This paper presents the application of discrete-time
variable structure control with sliding mode based on the 'reaching
law' method for robust control of a 'simple inverted pendulum on
moving cart' - a standard nonlinear benchmark system. The
controllers designed using the above techniques are completely
insensitive to parametric uncertainty and external disturbance. The
controller design is carried out using pole placement technique to find
state feedback gain matrix , which decides the dynamic behavior
of the system during sliding mode. This is followed by feedback gain
realization using the control law which is synthesized from 'Gao-s
reaching law'. The model of a single inverted pendulum and the
discrete variable structure control controller are developed, simulated
in MATLAB-SIMULINK and results are presented. The response of
this simulation is compared with that of the discrete linear quadratic
regulator (DLQR) and the advantages of sliding mode controller over
DLQR are also presented
Abstract: The aim of this investigation is to study the
performance of the new generation of the PVD coated grade and to
map the influence of cutting conditions on the tool life in milling of
ADI (Austempered Ductile Iron). The results show that chipping is
the main wear mechanism which determines the tool life in dry
condition and notch wear in wet condition for this application. This
due to the different stress mechanisms and preexisting cracks in the
coating. The wear development shows clearly that the new PVD
coating (C20) has the best ability to delay the chipping growth. It
was also found that a high content of Al in the new coating (C20)
was especially favorable compared to a TiAlN multilayer with lower
Al content (C30) or CVD coating. This is due to fine grains and low
compressive stress level in the coating which increase the coating
ability to withstand the mechanical and thermal impact. It was also
found that the use of coolant decreases the tool life with 70-80%
compare to dry milling.