Abstract: Increasing demand on the performance of Subsea
Production Systems (SPS) suggests a need for more detailed
investigation of fluid behavior taking place in subsea equipment.
Complete CFD cool down analyses of subsea equipment are very
time demanding. The objective of this paper is to investigate a
Locked CFD approach, which enables significant reduction of the
computational time and at the same time maintains sufficient
accuracy during thermal cool down simulations. The result
comparison of a dead leg simulation using the Full CFD and the three
LCFD-methods confirms the validity of the locked flow field
assumption for the selected case. For the tested case the LCFD
simulation speed up by factor of 200 results in the absolute thermal
error of 0.5 °C (3% relative error), speed up by factor of 10 keeps the
LCFD results within 0.1 °C (0.5 % relative error) comparing to the
Full CFD.
Abstract: Renewable and non-renewable resource constraints have been vast studied in theoretical fields of project scheduling problems. However, although cumulative resources are widespread in practical cases, the literature on project scheduling problems subject to these resources is scant. So in order to study this type of resources more, in this paper we use the framework of a resource constrained project scheduling problem (RCPSP) with finish-start precedence relations between activities and subject to the cumulative resources in addition to the renewable resources. We develop a branch and bound algorithm for this problem customizing precedence tree algorithm of RCPSP. We perform extensive experimental analysis on the algorithm to check its effectiveness and performance for solving different instances of the problem in question.
Abstract: In this paper, a neural network tuned fuzzy controller
is proposed for controlling Multi-Input Multi-Output (MIMO)
systems. For the convenience of analysis, the structure of MIMO
fuzzy controller is divided into single input single-output (SISO)
controllers for controlling each degree of freedom. Secondly,
according to the characteristics of the system-s dynamics coupling, an
appropriate coupling fuzzy controller is incorporated to improve the
performance. The simulation analysis on a two-level mass–spring
MIMO vibration system is carried out and results show the
effectiveness of the proposed fuzzy controller. The performance
though improved, the computational time and memory used is
comparatively higher, because it has four fuzzy reasoning blocks and
number may increase in case of other MIMO system. Then a fuzzy
neural network is designed from a set of input-output training data to
reduce the computing burden during implementation. This control
strategy can not only simplify the implementation problem of fuzzy
control, but also reduce computational time and consume less
memory.
Abstract: In the closed quantum system, if the control system is
strongly regular and all other eigenstates are directly coupled to the
target state, the control system can be asymptotically stabilized at the
target eigenstate by the Lyapunov control based on the state error.
However, if the control system is not strongly regular or as long as
there is one eigenstate not directly coupled to the target state, the
situations will become complicated. In this paper, we propose an
implicit Lyapunov control method based on the state error to solve the
convergence problems for these two degenerate cases. And at the same
time, we expand the target state from the eigenstate to the arbitrary
pure state. Especially, the proposed method is also applicable in the
control system with multi-control Hamiltonians. On this basis, the
convergence of the control systems is analyzed using the LaSalle
invariance principle. Furthermore, the relation between the implicit
Lyapunov functions of the state distance and the state error is
investigated. Finally, numerical simulations are carried out to verify
the effectiveness of the proposed implicit Lyapunov control method.
The comparisons of the control effect using the implicit Lyapunov
control method based on the state distance with that of the state error
are given.
Abstract: The recent advances in computational fluid dynamics
(CFD) can be useful in observing the detailed hemodynamics in
cerebral aneurysms for understanding not only their formation and
rupture but also for clinical evaluation and treatment. However,
important hemodynamic quantities are difficult to measure in vivo. In
the present study, an approximate model of normal middle cerebral
artery (MCA) along with two cases consisting broad and narrow
saccular aneurysms are analyzed. The models are generated in
ANSYS WORKBENCH and transient analysis is performed in
ANSYS-CFX. The results obtained are compared for three cases and
agree well with the available literature.
Abstract: The objective of this study is to examine the validity of Wagner-s law and relationship between economic growth, population and export for Pakistan. The ARDL Bounds cointegration and ECM are utilized for long and short run equilibrium for the period of 1972-2007. Population has considerable role in an economy and exports are the main source to raise the GDP. With the increase in GDP, the government expenditures may or may not increase. The empirical results indicate that the Wagner-s Law does hold, as economic growth is significantly and positively correlated with government expenditures. However, population and exports have also significant and positive impact on government expenditures both in short and long run. The significant and negative coefficient of error correction term in ECM indicates that after a shock, the long rum equilibrium will again converge towards equilibrium about 70.82 percent within a year.
Abstract: This paper presents an experimental case using sensory thermography to describe temperatures behavior on median nerve once an activity of repetitive motion was done. Thermography is a noninvasive technique without biological hazard and not harm at all times and has been applied in many experiments to seek for temperature patterns that help to understand diseases like cancer and cumulative trauma disorders (CTD’s). An infrared sensory thermography technology was developed to execute this study. Three women in good shape were selected for the repetitive motion tests for 4 days, two right-handed women and 1 left handed woman, two sensory thermographers were put on both median nerve wrists to get measures. The evaluation time was of 3 hours 30 minutes in a controlled temperature, 20 minutes of stabilization time at the beginning and end of the operation. Temperatures distributions are statistically evaluated and showed similar temperature patterns behavior.
Abstract: This paper presents the cepstral and trispectral
analysis of a speech signal produced by normal men, men with
defective audition (deaf, deep deaf) and others affected by
tracheotomy, the trispectral analysis based on parametric methods
(Autoregressive AR) using the fourth order cumulant. These
analyses are used to detect and compare the pitches and the formants
of corresponding voiced sounds (vowel \a\, \i\ and \u\). The first
results appear promising, since- it seems after several experimentsthere
is no deformation of the spectrum as one could have supposed
it at the beginning, however these pathologies influenced the two
characteristics:
The defective audition influences to the formants contrary to the
tracheotomy, which influences the fundamental frequency (pitch).
Abstract: Increasing concerns over climate change have limited
the liberal usage of available energy technology options. India faces
a formidable challenge to meet its energy needs and provide adequate
energy of desired quality in various forms to users in sustainable
manner at reasonable costs. In this paper, work carried out with an
objective to study the role of various energy technology options
under different scenarios namely base line scenario, high nuclear
scenario, high renewable scenario, low growth and high growth rate
scenario. The study has been carried out using Model for Energy
Supply Strategy Alternatives and their General Environmental
Impacts (MESSAGE) model which evaluates the alternative energy
supply strategies with user defined constraints on fuel availability,
environmental regulations etc. The projected electricity demand, at
the end of study period i.e. 2035 is 500490 MWYr. The model
predicted the share of the demand by Thermal: 428170 MWYr,
Hydro: 40320 MWYr, Nuclear: 14000 MWYr, Wind: 18000 MWYr
in the base line scenario. Coal remains the dominant fuel for
production of electricity during the study period. However, the
import dependency of coal increased during the study period. In
baseline scenario the cumulative carbon dioxide emissions upto 2035
are about 11,000 million tones of CO2. In the scenario of high nuclear
capacity the carbon dioxide emissions reduced by 10 % when nuclear
energy share increased to 9 % compared to 3 % in baseline scenario.
Similarly aggressive use of renewables reduces 4 % of carbon
dioxide emissions.
Abstract: In the way of growing and developing firms especially
high-tech firms, on many occasions manager of firm is mainly involved in solving problems of his business and decision making about executive activities of the firm, while besides executive
measures, attention to planning of firm's success and growth way and
application of long experience and sagacity in designing business model are vital and necessary success in a business is achieved as a
result of different factors, one of the most important of them is designing and performing an optimal business model at the beginning
of the firm's work. This model is determining the limit of profitability
achieved by innovation and gained value added. Therefore, business
model is the process of connecting innovation environment and
technology with economic environment and business and is important
for succeeding modern businesses considering their traits.
Abstract: A rigorous two-dimensional model is developed for simulating the operation of a less-investigated type steam reformer having a considerably lower operating Reynolds number, higher tube diameter, and non-availability of extra steam in the feed compared with conventional steam reformers. Simulation results show that reasonable predictions can only be achieved when certain correlations for wall to fluid heat transfer equations are applied. Due to severe operating conditions, in all cases, strong radial temperature gradients inside the reformer tubes have been found. Furthermore, the results show how a certain catalyst loading profile will affect the operation of the reformer.
Abstract: In order to monitor the water table depth on soil profile
salinity buildup, a field study was carried out during 2006-07. Wheat
(Rabi) and Sorghum (Kharif) fodder were sown in with three
treatments. The results showed that watertable depth lowered from
1.15m to 2.89 m depth at the end of experiment. With lower of
watertable depth, pH, ECe and SAR decreased under crops both
without and with gypsum and increased in fallowing. Soil moisture
depletion was directly proportional to lowering of watertable. With the
application of irrigation water (58cm) pH, ECe and SAR were reduced
in cropped plots, reduction was higher in gypsum applied plots than
non-gypsum plots. In case of fallowing, there was increase in pH, EC,
while slight reduction occurred in SAR values. However, soil salinity
showed an increasing upward trend under fallowing and its value in
0-30 cm soil layer was the highest amongst the treatments.
Abstract: There has been gradual progress of late in construction projects, particularly in big-scale megaprojects. Due to the long-term construction period, however, with large-scale budget investment, lack of construction management technologies, and increase in the incomplete elements of project schedule management, a plan to conduct efficient operations and to ensure business safety is required. In particular, as the project management information system (PMIS) is meant for managing a single project centering on the construction phase, there is a limitation in the management of program-scale businesses like megaprojects. Thus, a program management information system (PgMIS) that includes program-level management technologies is needed to manage multiple projects. In this study, a support tool was developed for managing the cost and schedule information occurring in the construction phase, at the program level. In addition, a case study on the developed support tool was conducted to verify the usability of the system. With the use of the developed support tool program, construction managers can monitor the progress of the entire project and of the individual subprojects in real time.
Abstract: Curriculum is one of the most important inputs in higher education system and for knowing the strong and weak spots of it we need evaluation. The main purpose of this study was to survey of the curriculum quality of Insurance Management field. Case: University of Allameh Taba Tabaee(according to view point of students,alumni,employer and faculty members).Descriptive statistics (mean, tables, percentages, frequency distribution) and inferential statistics (CHI SQUARE) were used to analyze the data. Six criterions considered for the Quality of curriculum: objectives, content, teaching and learning methods, space and facilities, Time, assessment of learning. objectives, teaching and learning methods criterions was desirable level, content criteria was undesirable level, space and facilities, time and assessment of learning were rather desirable level. The quality of curriculum of insurance management field was relatively desirable level.
Abstract: In this paper, the Tabu search algorithm is used to
solve a transportation problem which consists of determining the
shortest routes with the appropriate vehicle capacity to facilitate the
travel of the students attending the University of Mauritius. The aim
of this work is to minimize the total cost of the distance travelled by
the vehicles in serving all the customers. An initial solution is
obtained by the TOUR algorithm which basically constructs a giant
tour containing all the customers and partitions it in an optimal way
so as to produce a set of feasible routes. The Tabu search algorithm
then makes use of a search procedure, a swapping procedure and the
intensification and diversification mechanism to find the best set of
feasible routes.
Abstract: Recommender systems are usually regarded as an
important marketing tool in the e-commerce. They use important
information about users to facilitate accurate recommendation. The
information includes user context such as location, time and interest
for personalization of mobile users. We can easily collect information
about location and time because mobile devices communicate with the
base station of the service provider. However, information about user
interest can-t be easily collected because user interest can not be
captured automatically without user-s approval process. User interest
usually represented as a need. In this study, we classify needs into two
types according to prior research. This study investigates the
usefulness of data mining techniques for classifying user need type for
recommendation systems. We employ several data mining techniques
including artificial neural networks, decision trees, case-based
reasoning, and multivariate discriminant analysis. Experimental
results show that CHAID algorithm outperforms other models for
classifying user need type. This study performs McNemar test to
examine the statistical significance of the differences of classification
results. The results of McNemar test also show that CHAID performs
better than the other models with statistical significance.
Abstract: Despite the extensive use of eLearning systems, there
is no consensus on a standard framework for evaluating this kind of
quality system. Hence, there is only a minimum set of tools that can
supervise this judgment and gives information about the course
content value. This paper presents two kinds of quality set evaluation
indicators for eLearning courses based on the computational process
of three known metrics, the Euclidian, Hamming and Levenshtein
distances. The “distance" calculus is applied to standard evaluation
templates (i.e. the European Commission Programme procedures vs.
the AFNOR Z 76-001 Standard), determining a reference point in the
evaluation of the e-learning course quality vs. the optimal concept(s).
The case study, based on the results of project(s) developed in the
framework of the European Programme “Leonardo da Vinci", with
Romanian contractors, try to put into evidence the benefits of such a
method.
Abstract: Existing work in temporal logic on representing the
execution of infinitely many transactions, uses linear-time temporal
logic (LTL) and only models two-step transactions. In this paper,
we use the comparatively efficient branching-time computational tree
logic CTL and extend the transaction model to a class of multistep
transactions, by introducing distinguished propositional variables
to represent the read and write steps of n multi-step transactions
accessing m data items infinitely many times. We prove that the
well known correspondence between acyclicity of conflict graphs
and serializability for finite schedules, extends to infinite schedules.
Furthermore, in the case of transactions accessing the same set of
data items in (possibly) different orders, serializability corresponds
to the absence of cycles of length two. This result is used to give an
efficient encoding of the serializability condition into CTL.
Abstract: Thailand-s health system is challenged by the rising
number of patients and decreasing ratio of medical
practitioners/patients, especially in rural areas. This may tempt
inexperienced GPs to rush through the process of anamnesis with the
risk of incorrect diagnosis. Patients have to travel far to the hospital
and wait for a long time presenting their case. Many patients try to
cure themselves with traditional Thai medicine. Many countries are
making use of the Internet for medical information gathering,
distribution and storage. Telemedicine applications are a relatively
new field of study in Thailand; the infrastructure of ICT had
hampered widespread use of the Internet for using medical
information. With recent improvements made health and technology
professionals can work out novel applications and systems to help
advance telemedicine for the benefit of the people. Here we explore
the use of telemedicine for people with health problems in rural areas
in Thailand and present a Telemedicine Diagnosis System for Rural
Thailand (TEDIST) for diagnosing certain conditions that people
with Internet access can use to establish contact with Community
Health Centers, e.g. by mobile phone. The system uses a Web-based
input method for individual patients- symptoms, which are taken by
an expert system for the analysis of conditions and appropriate
diseases. The analysis harnesses a knowledge base and a backward
chaining component to find out, which health professionals should be
presented with the case. Doctors have the opportunity to exchange
emails or chat with the patients they are responsible for or other
specialists. Patients- data are then stored in a Personal Health Record.
Abstract: The V-notches are most possible case for initiation of cracks in parts. The specifications of cracks on the tip of the notch will be influenced via opening angle, tip radius and depth of V-notch. In this study, the effects of V-notch-s opening angle on stress intensity factor and T-stress of crack on the notch has been investigated. The experiment has been done in different opening angles and various crack length in mode (I) loading using Photoelasticity method. The results illustrate that while angle increases in constant crack-s length, SIF and T-stress will decrease. Beside, the effect of V-notch angle in short crack is more than long crack. These V-notch affects are negligible by increasing the length of crack, and the crack-s behavior can be considered as a single-edge crack specimen. Finally, the results have been evaluated with numerical finite element analysis and good agreement was obvious.