Abstract: In the present research, a finite element model is
presented to study the geometrical and material nonlinear behavior of
reinforced concrete plane frames considering soil-structure
interaction. The nonlinear behaviors of concrete and reinforcing steel
are considered both in compression and tension up to failure. The
model takes account also for the number, diameter, and distribution
of rebar along every cross section. Soil behavior is taken into
consideration using four different models; namely: linear-, nonlinear
Winkler's model, and linear-, nonlinear continuum model. A
computer program (NARC) is specially developed in order to
perform the analysis. The results achieved by the present model show
good agreement with both theoretical and experimental published
literature. The nonlinear behavior of a rectangular frame resting on
soft soil up to failure using the proposed model is introduced for
demonstration.
Abstract: The combustion of liquid fuel in the porous burner
(PB) was experimented to investigate evaporation mechanism and
combustion behavior. The diesel oil was used as fuel and the pebbles
carefully chosen in the same size like the solid sphere homogeneously
was adopted as the porous media. Two structures of the liquid porous
burner, i.e. the PB without and with installation of porous emitter
(PE), were performed. PE was installed by lower than PB with
distance of 20 cm. The pebbles having porosity (φ) of 0.45 and 0.52
were, respectively, used in PB and PE. The fuel was supplied dropwise
from the top through the PB and the combustion was occurred between
PB and PE. Axial profiles of temperature along the burner length were
measured to clarify the evaporation and combustion phenomena. The
pollutant emission characteristics were monitored at the burner exit.
From the experiment, it was found that the temperature profiles of both
structures decreased with the three ways swirling air flows (QA)
increasing. On the other hand, the temperature profiles increased with
fuel heat input (QF). Obviously, the profile of the porous burner
installed with PE was higher than that of the porous burner without
PE
Abstract: The use of composite materials in offshore engineering for deep sea oil production riser systems has drawn considerable interest due to the potential weight savings and improvement in durability. The design of composite risers consists of two stages: (1) local design based on critical local load cases, and (2) global analysis of the full length composite riser under global loads and assessment of critical locations. In the first stage, eight different material combinations were selected and their laminate configurations optimised under local load considerations. Stage two includes a final local stress analysis of the critical sections of the riser under the combined loads determined in the global analysis. This paper describes two design methodologies of the composite riser to provide minimum structural weight and shows that the use of off angle fibre orientations in addition to axial and hoop reinforcements offer substantial weight savings and ensure the structural capacity.
Abstract: The system is made with main distributed components:
First Level: Industrial Computers placed in Control Room (monitors thermal and electrical processes based on the data provided by the second level); Second Level: PLCs which collects data from process and transmits information on the first level; also takes commands from this level which are further, passed to execution elements from third
level; Third Level: field elements consisting in 3 categories: data collecting elements; data transfer elements from the third level to the second; execution elements which take commands from the second
level PLCs and executes them after which transmits the confirmation of execution to them. The purpose of the automatic functioning is the optimization of the co-generative electrical energy commissioning in the national
energy system and the commissioning of thermal energy to the consumers.
The integrated system treats the functioning of all the equipments and devices as a whole: Gas Turbine Units (GTU); MT 20kV Medium Voltage Station (MVS); 0,4 kV Low Voltage Station (LVS); Main Hot Water Boilers (MHW); Auxiliary Hot Water Boilers (AHW); Gas Compressor Unit (GCU); Thermal Agent Circulation
Pumping Unit (TPU); Water Treating Station (WTS).
Abstract: Aiming at the problems existing in low-carbon technology of Chinese manufacturing industries, such as irrational energy structure, lack of technological innovation, financial constraints, this paper puts forward the suggestion that the leading role of the government is combined with the roles of enterprises and market. That is, through increasing the governmental funding the adjustment of the industrial structures and enhancement of the legal supervision are supported. Technological innovation is accelerated by the enterprises, and the carbon trading will be promoted so as to trigger the low-carbon revolution in Chinese manufacturing field.
Abstract: This paper proposes a scheduling scheme using feedback
control to reduce the response time of aperiodic tasks with soft
real-time constraints. We design an algorithm based on the proposed
scheduling scheme and Total Bandwidth Server (TBS) that is a
conventional server technique for scheduling aperiodic tasks. We then
describe the feedback controller of the algorithm and give the control
parameter tuning methods. The simulation study demonstrates that the
algorithm can reduce the mean response time up to 26% compared
to TBS in exchange for slight deadline misses.
Abstract: Employees commitments of vision and mission of
organization is effected due to manager’s executes by approach of
leadership The leaders who have attributions like vision, confidence
and correctitude, sharing and participation, creativeness, progressive
learning –improvement and responsibility are effective to increase
organizational commitment if they are sensitive to expectation and
requirement of employees in an organization. Studies about
organizational commitment appear results that employees who have
strong organizational commitment have the most contribution. In this
study, “Leadership” and “Organizational Commitment” conduct
surveys to 31 employees of Ahmet Özdemir Nak. Tic. San. A.Ş.
which has operations in road and railway transportation sector. It is
analyzed the effects of leadership approach to organizational
commitment deals with result of survey.
Abstract: Direction of Arrival estimation refers to defining a mathematical function called a pseudospectrum that gives an indication of the angle a signal is impinging on the antenna array. This estimation is an efficient method of improving the quality of service in a communication system by focusing the reception and transmission only in the estimated direction thereby increasing fidelity with a provision to suppress interferers. This improvement is largely dependent on the performance of the algorithm employed in the estimation. Many DOA algorithms exists amongst which are MUSIC, Root-MUSIC and ESPRIT. In this paper, performance of these three algorithms is analyzed in terms of complexity, accuracy as assessed and characterized by the CRLB and memory requirements in various environments and array sizes. It is found that the three algorithms are high resolution and dependent on the operating environment and the array size.
Abstract: The nexus between language and culture is so
intertwined and very significant that language is largely seen as a
vehicle for cultural transmission. Culture itself refers to the aggregate
belief system of a people, embellishing its corporate national image
or brand. If we conceive national rebranding as a campaign to
rekindle the patriotic flame in the consciousness of a people towards
its sociocultural imperatives and values, then, Nigerian indigenous
linguistic flame has not been ignited. Consequently, the paper
contends that the current national rebranding policy remains a myth
in the confines of the elitists' intellectual squabble. It however
recommends that the use of our indigenous languages should be
supported by adequate legislation and also propagated by Nollywood
in order to revamp and sustain the people’s interest in their local
languages. Finally, the use of the indigenous Nigerian languages
demonstrates patriotism, an important ingredient for actualizing a
genuine national rebranding.
Abstract: This article presents the results of researchrelated to the assessment protocol weightedcumulative expected transmission time (WCETT)applied to cognitive radio networks.The development work was based on researchdone by different authors, we simulated a network,which communicates wirelessly, using a licensedchannel, through which other nodes are notlicensed, try to transmit during a given time nodeuntil the station's owner begins its transmission.
Abstract: Wireless sensor networks can be used to measure and monitor many challenging problems and typically involve in monitoring, tracking and controlling areas such as battlefield monitoring, object tracking, habitat monitoring and home sentry systems. However, wireless sensor networks pose unique security challenges including forgery of sensor data, eavesdropping, denial of service attacks, and the physical compromise of sensor nodes. Node in a sensor networks may be vanished due to power exhaustion or malicious attacks. To expand the life span of the sensor network, a new node deployment is needed. In military scenarios, intruder may directly organize malicious nodes or manipulate existing nodes to set up malicious new nodes through many kinds of attacks. To avoid malicious nodes from joining the sensor network, a security is required in the design of sensor network protocols. In this paper, we proposed a security framework to provide a complete security solution against the known attacks in wireless sensor networks. Our framework accomplishes node authentication for new nodes with recognition of a malicious node. When deployed as a framework, a high degree of security is reachable compared with the conventional sensor network security solutions. A proposed framework can protect against most of the notorious attacks in sensor networks, and attain better computation and communication performance. This is different from conventional authentication methods based on the node identity. It includes identity of nodes and the node security time stamp into the authentication procedure. Hence security protocols not only see the identity of each node but also distinguish between new nodes and old nodes.
Abstract: Stochastic resonance (SR) is a phenomenon whereby
the signal transmission or signal processing through certain nonlinear
systems can be improved by adding noise. This paper discusses SR in
nonlinear signal detection by a simple test statistic, which can be
computed from multiple noisy data in a binary decision problem based
on a maximum a posteriori probability criterion. The performance of
detection is assessed by the probability of detection error Per . When
the input signal is subthreshold signal, we establish that benefit from
noise can be gained for different noises and confirm further that the
subthreshold SR exists in nonlinear signal detection. The efficacy of
SR is significantly improved and the minimum of Per can
dramatically approach to zero as the sample number increases. These
results show the robustness of SR in signal detection and extend the
applicability of SR in signal processing.
Abstract: Nowadays, quasi-continuous wave diode lasers are
used in a widespread variety of applications. Temperature effects in
these lasers can strongly influence their performance. In this paper,
the effects of temperature have been experimentally investigated on
different features of a 60W-QCW diode laser. The obtained results
indicate that the conversion efficiency and operation voltage of diode
laser decrease with the augmentation of the working temperature
associated with a redshift in the laser peak wavelength. Experimental
results show the emission peak wavelength of laser shifts 0.26 nm
and the conversion efficiency decreases 1.76 % with the increase of
temperature from 40 to 50 ̊C. Present study also shows the slope
efficiency decreases gradually at low temperatures and rapidly at
higher temperatures. Regarding the close dependence of the
mentioned parameters to the operating temperature, it is of great
importance to carefully control the working temperature of diode
laser, particularly for medical applications.
Abstract: A new and novel approach in medicine is the use of
cold plasma for various applications such as sterilization blood
coagulation and cancer cell treatment. In this paper a pin-to-hole
plasma jet suitable for biological applications is investigated and
characterized and the possibility and feasibility of cancer cell
treatment is evaluated. The characterization includes power
consumption via Lissajous method, thermal behavior of plasma using
Infra-red camera as a novel method, Optical Emission Spectroscopy
(OES) to determine the species that are generated. Treatment of
leukemia cancer cells is also implemented and MTT assay is used to
evaluate viability.
Abstract: Atmospheric plasma is emerging as a promising
technology for many industrial sectors, because of its ecological and
economic advantages respect to the traditional production processes.
For textile industry, atmospheric plasma is becoming a valid
alternative to the conventional wet processes, but the plasma
machines realized so far do not allow the treatment of fibrous
mechanically weak material.
Novel atmospheric plasma machine for industrial applications,
developed by VenetoNanotech SCpA in collaboration with Italian
producer of corona equipment ME.RO SpA is presented. The main
feature of this pre-industrial scale machine is the possibility of the inline
plasma treatment of delicate fibrous substrates such as fibre
sleeves, for example wool tops, cotton fibres, polymeric tows,
mineral fibers and so on, avoiding burnings and disruption of the
faint materials.
Abstract: In this paper, the computation of the electrical field distribution around AC high-voltage lines is demonstrated. The advantages and disadvantages of two different methods are described to evaluate the electrical field quantity. The first method is a seminumerical method using the laws of electrostatic techniques to simulate the two-dimensional electric field under the high-voltage overhead line. The second method which will be discussed is the finite element method (FEM) using specific boundary conditions to compute the two- dimensional electric field distributions in an efficient way.
Abstract: It is hard to percept the interaction process with machines when visual information is not available. In this paper, we have addressed this issue to provide interaction through visual techniques. Posture recognition is done for American Sign Language to recognize static alphabets and numbers. 3D information is exploited to obtain segmentation of hands and face using normal Gaussian distribution and depth information. Features for posture recognition are computed using statistical and geometrical properties which are translation, rotation and scale invariant. Hu-Moment as statistical features and; circularity and rectangularity as geometrical features are incorporated to build the feature vectors. These feature vectors are used to train SVM for classification that recognizes static alphabets and numbers. For the alphabets, curvature analysis is carried out to reduce the misclassifications. The experimental results show that proposed system recognizes posture symbols by achieving recognition rate of 98.65% and 98.6% for ASL alphabets and numbers respectively.
Abstract: Since the 1940s, many promising telepresence
research results have been obtained. However, telepresence
technology still has not reached industrial usage. As human
intelligence is necessary for successful execution of most manual
assembly tasks, the ability of the human is hindered in some cases,
such as the assembly of heavy parts of small/medium lots or
prototypes. In such a case of manual assembly, the help of industrial
robots is mandatory. The telepresence technology can be considered
as a solution for performing assembly tasks, where the human
intelligence and haptic sense are needed to identify and minimize the
errors during an assembly process and a robot is needed to carry
heavy parts. In this paper, preliminary steps to integrate the
telepresence technology into industrial robot systems are introduced.
The system described here combines both, the human haptic sense
and the industrial robot capability to perform a manual assembly task
remotely using a force feedback joystick. Mapping between the
joystick-s Degrees of Freedom (DOF) and the robot-s ones are
introduced. Simulation and experimental results are shown and future
work is discussed.
Abstract: Homogeneous Charge Compression (HCCI) Ignition technology has been around for a long time, but has recently received renewed attention and enthusiasm. This paper deals with experimental investigations of HCCI engine using hydrous methanol as a primary fuel and Dimethyl Ether (DME) as an ignition improver. A regular diesel engine has been modified to work as HCCI engine for this investigation. The hydrous methanol is inducted and DME is injected into a single cylinder engine. Hence, hydrous methanol is used with 15% water content in HCCI engine and its performance and emission behavior is documented. The auto-ignition of Methanol is enabled by DME. The quantity of DME varies with respect to the load. In this study, the experiments are conducted independently and the effect of the hydrous methanol on the engine operating limit, heat release rate and exhaust emissions at different load conditions are investigated. The investigation also proves that the Hydrous Methanol with DME operation reduces the oxides of Nitrogen and smoke to an extreme low level which is not possible by the direct injection CI engine. Therefore, it is beneficial to use hydrous methanol-DME HCCI mode while using hydrous methanol in internal Combustion Engines.
Abstract: Optical Character Recognition (OCR) is a very old and of great interest in pattern recognition field. In this paper we introduce a very powerful approach to recognize Persian text. We have used morphological operators, especially Hit/Miss operator to descript each sub-word and by using a template matching approach we have tried to classify generated description. We used just one font in two different sizes to verify our approach. We achieved a very good rate, up to 99.9%.