Abstract: This study investigates how the site specific traffic
data differs from the Mechanistic Empirical Pavement Design
Software default values. Two Weigh-in-Motion (WIM) stations were
installed in Interstate-40 (I-40) and Interstate-25 (I-25) to developed
site specific data. A computer program named WIM Data Analysis
Software (WIMDAS) was developed using Microsoft C-Sharp (.Net)
for quality checking and processing of raw WIM data. A complete
year data from November 2013 to October 2014 was analyzed using
the developed WIM Data Analysis Program. After that, the vehicle
class distribution, directional distribution, lane distribution, monthly
adjustment factor, hourly distribution, axle load spectra, average
number of axle per vehicle, axle spacing, lateral wander distribution,
and wheelbase distribution were calculated. Then a comparative
study was done between measured data and AASHTOWare default
values. It was found that the measured general traffic inputs for I-40
and I-25 significantly differ from the default values.
Abstract: The end panels of a large rectangular industrial duct,
which experience significant internal pressures, also experience
considerable transverse shear due to transfer of gravity loads to the
supports. The current design practice of such thin plate panels for
shear load is based on methods used for the design of plate girder
webs. The structural arrangements, the loadings and the resulting
behavior associated with the industrial duct end panels are, however,
significantly different from those of the web of a plate girder. The
large aspect ratio of the end panels gives rise to multiple bands of
tension fields, whereas the plate girder web design is based on one
tension field. In addition to shear, the industrial end panels are
subjected to internal pressure which in turn produces significant
membrane action. This paper reports a study which was undertaken
to review the current industrial analysis and design methods and to
propose a comprehensive method of designing industrial duct end
panels for shear resistance. In this investigation, a nonlinear finite element model was
developed to simulate the behavior of industrial duct end panel, along
with the associated edge stiffeners, subjected to transverse shear and
internal pressures. The model considered the geometric imperfections
and constitutive relations for steels. Six scale independent
dimensionless parameters that govern the behavior of such end panel
were identified and were then used in a parametric study. It was
concluded that the plate slenderness dominates the shear strength of
stockier end panels, and whereas, both the plate slenderness and the
aspect ratio influence the shear strength of slender end panels. Based
on these studies, this paper proposes design aids for estimating the
shear strength of rectangular duct end panels.
Abstract: Agricultural machinery industry plays an important
role in the industrial development especially the production industry
of the country. There has been continuing development responding to
the higher demand of the production. However, the problem in
agricultural machinery production still exists. Thus, the purpose of
this research is to investigate problems on fundamental factors of
industry based on the entrepreneurs’ point of view. The focus was on
the small and medium size industry receiving factory license type
number 0660 from the Department of Industrial Works. The
investigation was on the comparison between the management of the
small and medium size agricultural industry in 3 provinces in the
central region of Thailand. Population in this study consisted of 189
company managers or managing directors, of which 101 were from
the small size and 88 were from the medium size industry. The data
were analyzed to find percentage, arithmetic mean, and standard
deviation with independent sample T-test at the statistical
significance .05. The results showed that the small and medium size
agricultural machinery manufacturers in the central region of
Thailand reported high problems in every aspect. When compared the
problems on basic factors in running the business, it was found that
there was no statistically difference at .05 in managing of the small
and medium size agricultural machinery manufacturers. However,
there was a statistically significant difference between the small and
medium size agricultural machinery manufacturers on the aspect of
policy and services of the government. The problems reported by the
small and medium size agricultural machinery manufacturers were
the services on public tap water and the problem on politic and
stability of the country.
Abstract: Increase of emergency incidents and crisis situations
requires proactive crisis management of authorities and for its
solution. Application Business Continuity Management helps the
crisis management authorities to quickly and responsibly respond to
threats. It also helps effectively and efficiently planning powers and
resources. The main goal of this article is describing Military
Continuity Management System (MCMS) based on the principles of
Business Continuity Management System (BCMS) for dealing with
floods in the territory of the selected municipalities. There are
explained steps of loading, running and evaluating activities in the
software application MCMS. Software MCMS provides complete
control over the tasks, contribute a comprehensive and responsible
approach solutions to solution floods in the municipality.
Abstract: Ensuring of continuity of business is basic strategy of
every company. Continuity of organization activities includes
comprehensive procedures that help in solving unexpected situations
of natural and anthropogenic character (for example flood, blaze,
economic situations). Planning of continuity operations is a process
that helps identify critical processes and implement plans for the
security and recovery of key processes. The aim of this article is to
demonstrate application of system approach to managing business
continuity called business continuity management systems in military
issues. This article describes the life cycle of business continuity
management which is based on the established cycle PDCA (Plan-
Do-Check-Act). After this is carried out by activities which are
making by University of Defence during activation of forces and
means of the integrated rescue system in case of emergencies -
accidents at a nuclear power plant in Czech Republic. Activities of
various stages of deployment earmarked forces and resources are
managed and evaluated by using MCMS application (Military
Continuity Management System).
Abstract: Password authentication is one of the widely used
methods to achieve authentication for legal users of computers and
defense against attackers. There are many different ways to
authenticate users of a system and there are many password cracking
methods also developed. This paper proposes how best password
cracking can be performed on a CPU-GPGPU based system. The
main objective of this work is to project how quickly a password can
be cracked with some knowledge about the computer security and
password cracking if sufficient security is not incorporated to the
system.
Abstract: Project Portfolio Management (PPM) is an essential
component of an organisation’s strategic procedures, which requires
attention of several factors to envisage a range of long-term outcomes
to support strategic project portfolio decisions. To evaluate overall
efficiency at the portfolio level, it is essential to identify the
functionality of specific projects as well as to aggregate those
findings in a mathematically meaningful manner that indicates the
strategic significance of the associated projects at a number of levels
of abstraction. PPM success is directly associated with the quality of
decisions made and poor judgment increases portfolio costs. Hence,
various Multi-Criteria Decision Making (MCDM) techniques have
been designed and employed to support the decision-making
functions. This paper reviews possible options to enhance the
decision-making outcomes in organisational portfolio management
processes using the Analytic Hierarchy Process (AHP) both from
academic and practical perspectives and will examine the usability,
certainty and quality of the technique. The results of the study will
also provide insight into the technical risk associated with current
decision-making model to underpin initiative tracking and strategic
portfolio management.
Abstract: A seizure prediction method is proposed by extracting
global features using phase correlation between adjacent epochs for
detecting relative changes and local features using fluctuation/
deviation within an epoch for determining fine changes of different
EEG signals. A classifier and a regularization technique are applied
for the reduction of false alarms and improvement of the overall
prediction accuracy. The experiments show that the proposed method
outperforms the state-of-the-art methods and provides high prediction
accuracy (i.e., 97.70%) with low false alarm using EEG signals in
different brain locations from a benchmark data set.
Abstract: The aim of the study was to investigate the effect of
Saccharomyces cerevisiae (SC) live yeast culture on microbial
protein supply to small intestine in Kivircik male yearlings when fed
with different ratio of forage and concentrate diets. Four Kivircik
male yearlings with permanent rumen canula were used in the
experiment. The treatments were allocated to a 4x4 Latin square
design. Diet I consisted of 70% alfalfa hay and 30% concentrate, Diet
II consisted of 30% alfalfa hay and 70% concentrate, Diet I and II
were supplemented with a SC. Daily urine was collected and stored at
-20°C until analysis. Calorimetric methods were used for the
determination of urinary allantoin and creatinine levels. The
estimated microbial N supply to small intestine for Diets I, I+SC, II
and II+SC were 2.51, 2.64, 2.95 and 3.43 g N/d respectively.
Supplementation of Diets I and II with SC significantly affected the
allantoin levels in μmol/W0.75 (p
Abstract: The transesterification of dimethyl malonate (DMM)
with phenol has been studied in vapour phase over cordierite
honeycomb coated with solid acid catalysts such as ZrO2,
Mo(VI)/ZrO2 and SO42-/ZrO2. The catalytic materials were prepared
honeycomb coated, powder forms, and characterized for their total
surface acidity by NH3-TPD and crystalinity by powder XRD
methods. Phenyl methyl malonate (PMM) and diphenyl malonate
(DPM) were obtained as the reaction products. A good conversion of
DMM (up to 82%) of MPM with 95% selectivity was observed when
the reactions were carried out at a catalyst bed temperature of 200 °C
and flow-rate of 10 mL/h in presence of Mo(VI)/ZrO2 as catalyst.
However, over SO4^2-/ZrO2 catalyst, the yield of DPM was found to be
higher. The results have been interpreted based on the variation of
acidic properties and powder XRD phases of zirconia on
incorporation of Mo(VI) or SO42– ions. Transesterification reactions
were also carried out over powder forms of the catalytic materials
and the yield of the desired phenyl ester products were compared
with that of the HC coated catalytic materials. The solid acids were
found to be reusable when used for at least 5 reaction cycles.
Abstract: In this paper, a robust fault detection and isolation
(FDI) scheme is developed to monitor a multivariable nonlinear
chemical process called the Chylla-Haase polymerization reactor,
when it is under the cascade PI control. The scheme employs a radial
basis function neural network (RBFNN) in an independent mode to
model the process dynamics, and using the weighted sum-squared
prediction error as the residual. The Recursive Orthogonal Least
Squares algorithm (ROLS) is employed to train the model to
overcome the training difficulty of the independent mode of the
network. Then, another RBFNN is used as a fault classifier to isolate
faults from different features involved in the residual vector. Several
actuator and sensor faults are simulated in a nonlinear simulation of
the reactor in Simulink. The scheme is used to detect and isolate the
faults on-line. The simulation results show the effectiveness of the
scheme even the process is subjected to disturbances and
uncertainties including significant changes in the monomer feed rate,
fouling factor, impurity factor, ambient temperature, and
measurement noise. The simulation results are presented to illustrate
the effectiveness and robustness of the proposed method.
Abstract: Concurrent planning of project scheduling and
material ordering has been increasingly addressed within last decades
as an approach to improve the project execution costs. Therefore, we
have taken the problem into consideration in this paper, aiming to
maximize schedules quality robustness, in addition to minimize the
relevant costs. In this regard, a bi-objective mathematical model is
developed to formulate the problem. Moreover, it is possible to
utilize the all-unit discount for materials purchasing. The problem is
then solved by the E-constraint method, and the Pareto front is
obtained for a variety of robustness values. The applicability and
efficiency of the proposed model is tested by different numerical
instances, finally.
Abstract: Selenium is an-antioxidant which is important for
human health enters food chain through crops. In Kenya Zea mays is
consumed by 96% of population hence is a cheap and convenient
method to provide selenium to large number of population. Several
soil factors are known to have antagonistic effects on selenium
speciation hence the uptake by Zea mays. There are no studies in
Kenya that has been done to determine the effects of soil
characteristics (pH, Tcarbon, CEC, Eh) affect accumulation of
selenium in Zea mays grains in Maize Belt in Kenya. About 100 Zea mays grain samples together with 100 soil samples
were collected from the study site put in separate labeled Ziplocs and
were transported to laboratories at room temperature for analysis.
Maize grains were analyzed for selenium while soil samples were
analyzed for pH, Cat Ion Exchange Capacity, total carbon, and
electrical conductivity. The mean selenium in Zea mays grains varied from 1.82 ± 0.76
mg/Kg to 11±0.86 mg/Kg. There was no significant difference
between selenium levels between different grain batches {χ (Df =76)
= 26.04 P= 1.00} The pH levels varied from 5.43± 0.58 to 5.85±
0.32. No significant correlations between selenium in grains and soil
pH (Pearson’s correlations = - 0.143), and between selenium levels in
grains and the four (pH, Tcarbon, CEC, Eh) soil chemical
characteristics {F (4,91) = 0.721 p = 0.579} was observed. It can be concluded that the soil chemical characteristics in the
study site did not significantly affect the accumulation of native
selenium in Zea mays grains.
Abstract: The modelling of physical phenomena, such as the
earth’s free oscillations, the vibration of strings, the interaction of
atomic particles, or the steady state flow in a bar give rise to Sturm-
Liouville (SL) eigenvalue problems. The boundary applications of
some systems like the convection-diffusion equation, electromagnetic
and heat transfer problems requires the combination of Dirichlet and
Neumann boundary conditions. Hence, the incorporation of Robin
boundary condition in the analyses of Sturm-Liouville problem. This
paper deals with the computation of the eigenvalues and
eigenfunction of generalized Sturm-Liouville problems with Robin
boundary condition using the finite element method. Numerical
solution of classical Sturm–Liouville problem is presented. The
results show an agreement with the exact solution. High results
precision is achieved with higher number of elements.
Abstract: The aim of this work is to detect geometrical shape
objects in an image. In this paper, the object is considered to be as a
circle shape. The identification requires find three characteristics,
which are number, size, and location of the object. To achieve the
goal of this work, this paper presents an algorithm that combines
from some of statistical approaches and image analysis techniques.
This algorithm has been implemented to arrive at the major
objectives in this paper. The algorithm has been evaluated by using
simulated data, and yields good results, and then it has been applied
to real data.
Abstract: The underutilization of biomass resources in the
Philippines, combined with its growing population and the rise in
fossil fuel prices confirms demand for alternative energy sources. The
goal of this paper is to provide a comparison of MODIS-based and
Landsat-based agricultural land cover maps when used in the
estimation of rice hull’s available energy potential. Biomass resource
assessment was done using mathematical models and remote sensing
techniques employed in a GIS platform.
Abstract: Finding the optimal 3D path of an aerial vehicle under
flight mechanics constraints is a major challenge, especially when
the algorithm has to produce real time results in flight. Kinematics
models and Pythagorian Hodograph curves have been widely used
in mobile robotics to solve this problematic. The level of difficulty
is mainly driven by the number of constraints to be saturated at the
same time while minimizing the total length of the path. In this paper,
we suggest a pragmatic algorithm capable of saturating at the same
time most of dimensioning helicopter 3D trajectories’ constraints
like: curvature, curvature derivative, torsion, torsion derivative, climb
angle, climb angle derivative, positions. The trajectories generation
algorithm is able to generate versatile complex 3D motion primitives
feasible by a helicopter with parameterization of the curvature and the
climb angle. An upper ”motion primitives’ concatenation” algorithm
is presented based. In this article we introduce a new way of designing
three-dimensional trajectories based on what we call the ”Dubins
gliding symmetry conjecture”. This extremely performing algorithm
will be soon integrated to a real-time decisional system dealing with
inflight safety issues.
Abstract: In Algeria, the conditioning units of dates, generate
significant quantities of waste arising from sorting deviations. This
biomass, until then considered as a waste with high impact on the
environment can be transformed into high value added product. It is
possible to develop common dates of low commercial value, and put
on the local and international market a new generation of products
with high added values such as bio ethanol. Besides its use in
chemical synthesis, bio ethanol can be blended with gasoline to
produce a clean fuel while improving the octane.
Abstract: In this study, the time-dependent behavior of damaged
reinforced concrete shear wall structures strengthened with composite
plates having variable fibers spacing was investigated to analyze their
seismic response. In the analytical formulation, the adherent and the
adhesive layers are all modeled as shear walls, using the mixed Finite
Element Method (FEM). The anisotropic damage model is adopted to
describe the damage extent of the Reinforced Concrete shear walls.
The phenomenon of creep and shrinkage of concrete has been
determined by Eurocode 2. Large earthquakes recorded in Algeria
(El-Asnam and Boumerdes) have been tested to demonstrate the
accuracy of the proposed method. Numerical results are obtained for non-uniform distributions of
carbon fibers in epoxy matrices. The effects of damage extent and the
delay mechanism creep and shrinkage of concrete are highlighted.
Prospects are being studied.
Abstract: The purpose of this study is to propose an effective method to improve frictional coefficient between shoe rubber soles with added glass fibers and the surfaces of icy and snowy road in order to prevent slip-and-fall accidents by the users. The additional fibers into the rubber were uniformly tilted to the perpendicular direction of the frictional surface, where tilting angles were -60, -30, +30, +60, 90 degrees and 0 (as normal specimen), respectively. It was found that parallel arraignment was effective to improve the frictional coefficient when glass fibers were embedded in the shoe rubber, while perpendicular to normal direction of the embedded glass fibers on the shoe surface was also effective to do that once after they were exposed from the shoe rubber with its abrasion. These improvements were explained by the increase of stiffness against the shear deformation of the rubber at critical frictional state and adequate scratching of fibers when fibers were protruded in perpendicular to frictional direction, respectively. Most effective angle of tilting of frictional coefficient between rubber specimens and a stone was perpendicular (= 0 degree) to frictional direction. Combinative modified rubber specimen having 2 layers was fabricated where tilting angle of protruded fibers was 0 degree near the contact surface and tilting angle of embedded fibers was 90 degrees near back surface in thickness direction to further improve the frictional coefficient. Current study suggested that effective arraignments in tilting angle of the added fibers should be applied in designing rubber shoe soles to keep the safeties for users in regions of cold climates.