Abstract: This paper presents the effect of corrugation profile
geometry on the crushing behavior, energy absorption, failure
mechanism, and failure mode of woven roving glass fibre/epoxy
laminated composite tube. Experimental investigations were carried
out on composite tubes with three different profile shapes: sinusoidal,
triangular and trapezoidal. The tubes were subjected to lateral
compressive loading. On the addition to a radial corrugated
composite tube, cylindrical composite tube, were fabricated and
tested under the same condition in order to know the effect of
corrugation geometry. Typical histories of their deformation are
presented. Behavior of tubes as regards the peak crushing load,
energy absorbed and mode of crushing has been discussed. The
results show that the behavior of the tube under lateral compression
load is influenced by the geometry of the tube itself.
Abstract: Search for a tertiary substructure that geometrically
matches the 3D pattern of the binding site of a well-studied protein provides a solution to predict protein functions. In our previous work,
a web server has been built to predict protein-ligand binding sites
based on automatically extracted templates. However, a drawback of such templates is that the web server was prone to resulting in many
false positive matches. In this study, we present a sequence-order constraint to reduce the false positive matches of using automatically
extracted templates to predict protein-ligand binding sites. The binding site predictor comprises i) an automatically constructed template library and ii) a local structure alignment algorithm for
querying the library. The sequence-order constraint is employed to
identify the inconsistency between the local regions of the query protein and the templates. Experimental results reveal that the sequence-order constraint can largely reduce the false positive matches and is effective for template-based binding site prediction.
Abstract: Behavior of turbulent jet is relying on jet parameters,
environmental and geometric parameters. In this research, it has
attempt to Study effect of jet parameters of internal angle on
maximum effective length and velocity on centerline from nozzle
experimentally. Toward this end, four internal angles 30, 45, 60 and
90-degree are considered for this study in a flume with 600cm as
long, 100cm as high and 150cm in width. Various discharges were
used to evaluate effective length for a wide range of densimetric
Froude numbers F0, from 17.9 to 39.4 that is defined at the nozzle. As
a result, It is revealed that both velocity on centerline and effective
length decreases when nozzle angle decreased from 90° to 30°. The
results show that, for all range of Fr0 the Um/U0 ratio for nozzle with
α=90° on centerline increases 20% - 27% than nozzle with α=30° that
has lowest velocity on centerline than other nozzle.
Abstract: In contrast to existing methods which do not take into account multiconnectivity in a broad sense of this term, we develop mathematical models and highly effective combination (BIEM and FDM) numerical methods of calculation of stationary and quasistationary temperature field of a profile part of a blade with convective cooling (from the point of view of realization on PC). The theoretical substantiation of these methods is proved by appropriate theorems. For it, converging quadrature processes have been developed and the estimations of errors in the terms of A.Ziqmound continuity modules have been received. For visualization of profiles are used: the method of the least squares with automatic conjecture, device spline, smooth replenishment and neural nets. Boundary conditions of heat exchange are determined from the solution of the corresponding integral equations and empirical relationships. The reliability of designed methods is proved by calculation and experimental investigations heat and hydraulic characteristics of the gas turbine first stage nozzle blade.
Abstract: The purpose of this research is to reduce the amount of incomplete coating of stainless steel washers in the electrodeposition painting process by using an experimental design technique. The surface preparation was found to be a major cause of painted surface quality. The influence of pretreating and painting process parameters, which are cleaning time, chemical concentration and shape of hanger were studied. A 23 factorial design with two replications was performed. The analysis of variance for the designed experiment showed the great influence of cleaning time and shape of hanger. From this study, optimized cleaning time was determined and a newly designed electrical conductive hanger was proved to be superior to the original one. The experimental verification results showed that the amount of incomplete coating defects decreased from 4% to 1.02% and operation cost decreased by 10.5%.
Abstract: An improved topology of a voltage-fed quasi-resonant
soft switching LCrCdc series-parallel half bridge inverter with a constant-frequency for electronic ballast applications is proposed in this paper. This new topology introduces a low-cost solution to
reduce switching losses and circuit rating to achieve high-efficiency
ballast. Switching losses effect on ballast efficiency is discussed
through experimental point of view. In this discussion, an improved
topology in which accomplishes soft switching operation over a wide
power regulation range is proposed. The proposed structure uses reverse recovery diode to provide better operation for the ballast system. A symmetrical pulse wide modulation (PWM) control scheme is implemented to regulate a wide range of out-put power.
Simulation results are kindly verified with the experimental
measurements obtained by ballast-lamp laboratory prototype. Different load conditions are provided in order to clarify the
performance of the proposed converter.
Abstract: Grid computing is a high performance computing
environment to solve larger scale computational applications. Grid
computing contains resource management, job scheduling, security
problems, information management and so on. Job scheduling is a
fundamental and important issue in achieving high performance in
grid computing systems. However, it is a big challenge to design an
efficient scheduler and its implementation. In Grid Computing, there
is a need of further improvement in Job Scheduling algorithm to
schedule the light-weight or small jobs into a coarse-grained or
group of jobs, which will reduce the communication time,
processing time and enhance resource utilization. This Grouping
strategy considers the processing power, memory-size and
bandwidth requirements of each job to realize the real grid system.
The experimental results demonstrate that the proposed scheduling
algorithm efficiently reduces the processing time of jobs in
comparison to others.
Abstract: This paper presents the study of induced currents and
temperature distribution in gear heated by induction process using 2D
finite element (FE) model. The model is developed by coupling
Maxwell and heat transfer equations into a multi-physics model. The
obtained results allow comparing the medium frequency (MF) and
high frequency (HF) cases and the effect of machine parameters on
the evolution of induced currents and temperature during heating.
The sensitivity study of the temperature profile is conducted and the
case hardness is predicted using the final temperature profile. These
results are validated using tests and give a good understanding of
phenomena during heating process.
Abstract: Animation is simply defined as the sequencing of a
series of static images to generate the illusion of movement. Most
people believe that actual drawings or creation of the individual
images is the animation, when in actuality it is the arrangement of
those static images that conveys the motion. To become an animator,
it is often assumed that needed the ability to quickly design
masterpiece after masterpiece. Although some semblance of artistic
skill is a necessity for the job, the real key to becoming a great
animator is in the comprehension of timing. This paper will use a
combination of sprite animation, frame animation, and some other
techniques to cause a group of multi-colored static images to slither
around in the bounded area. In addition to slithering, the images
will also change the color of different parts of their body, much like
the real world creatures that have this amazing ability to change the
colors on their bodies do. This paper was implemented by using
Java 2 Standard Edition (J2SE).
It is both time-consuming and expensive to create animations,
regardless if they are created by hand or by using motion-capture
equipment. If the animators could reuse old animations and even
blend different animations together, a lot of work would be saved in
the process. The main objective of this paper is to examine a method
for blending several animations together in real time. This paper
presents and analyses a solution using Weighted Skeleton
Animation (WSA) resulting in limited CPU time and memory waste
as well as saving time for the animators. The idea presented is
described in detail and implemented. In this paper, text animation,
vertex animation, sprite part animation and whole sprite animation
were tested.
In this research paper, the resolution, smoothness and movement
of animated images will be carried out from the parameters, which
will be obtained from the experimental research of implementing
this paper.
Abstract: Based on an analysis of the mechanism of degradation of optical characteristics of the ZnO-pigmented white paint by electron irradiation, a model of single molecular color centers is built. An equation that explains the relationship between the changes of variation of the ZnO-pigmented white paint-s spectrum absorptance and electron fluence is derived. The uncertain parameters in the equation can be calculated using the curve fitting by experimental data. The result indicates that the model can be applied to predict the degradation of optical characteristics of ZnO-pigmented white paint by electron radiation.
Abstract: Microtomographic images and thin section (TS)
images were analyzed and compared against some parameters of
geological interest such as porosity and its distribution along the
samples. The results show that microtomography ( CT) analysis,
although limited by its resolution, have some interesting information
about the distribution of porosity (homogeneous or not) and can also
quantify the connected and non-connected pores, i.e., total porosity.
TS have no limitations concerning resolution, but are limited by the
experimental data available in regards to a few glass sheets for
analysis and also can give only information about the connected
pores, i.e., effective porosity. Those two methods have their own
virtues and flaws but when paired together they are able to
complement one another, making for a more reliable and complete
analysis.
Abstract: Thirty three re-wetting tests were conducted at
different combinations of temperatures (5.7- 46.30C) and relative
humidites (48.2-88.6%) with barley. Two most commonly used thinlayer
drying and rewetting models i.e. Page and Diffusion were
compared for their ability to the fit the experimental re-wetting data
based on the standard error of estimate (SEE) of the measured and
simulated moisture contents. The comparison shows both the Page
and Diffusion models fit the re-wetting experimental data of barley
well. The average SEE values for the Page and Diffusion models
were 0.176 % d.b. and 0.199 % d.b., respectively. The Page and
Diffusion models were found to be most suitable equations, to
describe the thin-layer re-wetting characteristics of barley over a
typically five day re-wetting. These two models can be used for the
simulation of deep-bed re-wetting of barley occurring during
ventilated storage and deep bed drying.
Abstract: As the development of digital technology is increasing,
Digital cinema is getting more spread.
However, content copy and attack against the digital cinema becomes
a serious problem. To solve the above security problem, we propose
“Additional Watermarking" for digital cinema delivery system. With
this proposed “Additional watermarking" method, we protect content
copyrights at encoder and user side information at decoder. It realizes
the traceability of the watermark embedded at encoder.
The watermark is embedded into the random-selected frames using
Hash function. Using it, the embedding position is distributed by Hash
Function so that third parties do not break off the watermarking
algorithm.
Finally, our experimental results show that proposed method is much
better than the convenient watermarking techniques in terms of
robustness, image quality and its simple but unbreakable algorithm.
Abstract: The H.264/AVC standard uses an intra prediction, 9
directional modes for 4x4 luma blocks and 8x8 luma blocks, 4
directional modes for 16x16 macroblock and 8x8 chroma blocks,
respectively. It means that, for a macroblock, it has to perform 736
different RDO calculation before a best RDO modes is determined.
With this Multiple intra-mode prediction, intra coding of H.264/AVC
offers a considerably higher improvement in coding efficiency
compared to other compression standards, but computational
complexity is increased significantly. This paper presents a fast intra
prediction algorithm for H.264/AVC intra prediction based a
characteristic of homogeneity information. In this study, the gradient
prediction method used to predict the homogeneous area and the
quadratic prediction function used to predict the nonhomogeneous
area. Based on the correlation between the homogeneity and block
size, the smaller block is predicted by gradient prediction and
quadratic prediction, so the bigger block is predicted by gradient
prediction. Experimental results are presented to show that the
proposed method reduce the complexity by up to 76.07%
maintaining the similar PSNR quality with about 1.94%bit rate
increase in average.
Abstract: This study reports the preparation of soft magnetic ribbons of Fe-based amorphous alloys using the single-roller melt-spinning technique. Ribbon width varied from 142 mm to 213 mm and, with a thickness of approximately 22 μm 2 μm. The microstructure and magnetic properties of the ribbons were characterized by differential scanning calorimeter (DSC), X-ray diffraction (XRD), vibrating sample magnetometer (VSM), and electrical resistivity measurements (ERM). The amorphous material properties dependence of the cooling rate and nozzle pressure have uneven surface in ribbon thicknesses are investigated. Magnetic measurement results indicate that some region of the ribbon exhibits good magnetic properties, higher saturation induction and lower coercivity. However, due to the uneven surface of 213 mm wide ribbon, the magnetic responses are not uniformly distributed. To understand the transformer magnetic performances, this study analyzes the measurements of a three-phase 2 MVA amorphous-cored transformer. Experimental results confirm that the transformer with a ribbon width of 142 mm has better magnetic properties in terms of lower core loss, exciting power, and audible noise.
Abstract: The tray/multi-tray distillation process is a topic that
has been investigated to great detail over the last decade by many
teams such as Jubran et al. [1], Adhikari et al. [2], Mowla et al. [3],
Shatat et al. [4] and Fath [5] to name a few. A significant amount of
work and effort was spent focusing on modeling and/simulation of
specific distillation hardware designs. In this work, we have focused
our efforts on investigating and gathering experimental data on
several engineering and design variables to quantify their influence
on the yield of the multi-tray distillation process. Our goals are to
generate experimental performance data to bridge some existing gaps
in the design, engineering, optimization and theoretical modeling
aspects of the multi-tray distillation process.
Abstract: In contrast to existing methods which do not take into account multiconnectivity in a broad sense of this term, we develop mathematical models and highly effective combination (BIEM and FDM) numerical methods of calculation of stationary and quasi-stationary temperature field of a profile part of a blade with convective cooling (from the point of view of realization on PC). The theoretical substantiation of these methods is proved by appropriate theorems. For it, converging quadrature processes have been developed and the estimations of errors in the terms of A.Ziqmound continuity modules have been received. For visualization of profiles are used: the method of the least squares with automatic conjecture, device spline, smooth replenishment and neural nets. Boundary conditions of heat exchange are determined from the solution of the corresponding integral equations and empirical relationships. The reliability of designed methods is proved by calculation and experimental investigations heat and hydraulic characteristics of the gas turbine first stage nozzle blade.
Abstract: Thermal load calculations have been performed for
multi-layered walls that are composed of three different parts; a
common (sand and cement) plaster, and two types of locally
produced soft and hard bricks. The masonry construction of these
layered walls was based on concrete-backed stone masonry made of
limestone bricks joined by mortar. These multilayered walls are
forming the outer walls of the building envelope of a typical Libyan
house. Based on the periodic seasonal weather conditions, within the
Libyan cost region during summer and winter, measured thermal
conductivity values were used to implement such seasonal variation
of heat flow and the temperature variations through the walls. The
experimental measured thermal conductivity values were obtained
using the Hot Disk technique. The estimation of the thermal
resistance of the wall layers ( R-values) is based on measurements
and calculations. The numerical calculations were done using a
simplified analytical model that considers two different wall
constructions which are characteristics of such houses. According to
the obtained results, the R-values were quite low and therefore,
several suggestions have been proposed to improve the thermal
loading performance that will lead to a reasonable human comfort
and reduce energy consumption.
Abstract: The present energy situation and the concerns
about global warming has stimulated active research interest
in non-petroleum, carbon free compounds and non-polluting
fuels, particularly for transportation, power generation, and
agricultural sectors. Environmental concerns and limited
amount of petroleum fuels have caused interests in the
development of alternative fuels for internal combustion (IC)
engines. The petroleum crude reserves however, are declining
and consumption of transport fuels particularly in the
developing countries is increasing at high rates. Severe
shortage of liquid fuels derived from petroleum may be faced
in the second half of this century. Recently more and more
stringent environmental regulations being enacted in the USA
and Europe have led to the research and development
activities on clean alternative fuels. Among the gaseous fuels
hydrogen is considered to be one of the clean alternative fuel.
Hydrogen is an interesting candidate for future internal
combustion engine based power trains. In this experimental
investigation, the performance and combustion analysis were
carried out on a direct injection (DI) diesel engine using
hydrogen with diesel following the TMI(Time Manifold
Injection) technique at different injection timings of 10
degree,45 degree and 80 degree ATDC using an electronic
control unit (ECU) and injection durations were controlled.
Further, the tests have been carried out at a constant speed of
1500rpm at different load conditions and it can be observed
that brake thermal efficiency increases with increase in load
conditions with a maximum gain of 15% at full load
conditions during all injection strategies of hydrogen. It was
also observed that with the increase in hydrogen energy share
BSEC started reducing and it reduced to a maximum of 9% as
compared to baseline diesel at 10deg ATDC injection during
maximum injection proving the exceptional combustion
properties of hydrogen.
Abstract: The purpose of this research is to establish the experimental conditions for removal of Cibacron Brilliant Yellow 3G-P dye (CBY) from aqueous solutions by sorption onto coffee husks as a low-cost sorbent. The effects of various experimental parameters (e.g. initial CBY dye concentration, sorbent mass, pH, temperature) were examined and the optimal experimental conditions were determined. The results indicated that the removal of the dye was pH dependent and at initial pH of 2, the dye was removed effectively. The CBY dye sorption data were fitted to Langmuir, Freundlich, Temkin and Dubinin-Radushkevich equilibrium models. The maximum sorption capacity of CBY dye ions onto coffee husks increased from 24.04 to 35.04 mg g-1 when the temperature was increased from 293 to 313 K. The calculated sorption thermodynamic parameters including ΔG°, ΔH°, and ΔS° indicated that the CBY dye sorption onto coffee husks is a spontaneous, endothermic and mainly physical in nature.