Abstract: In automotive systems almost all steps concerning the
calibration of several control systems, e.g., low idle governor or
boost pressure governor, are made with the vehicle because the timeto-
production and cost requirements on the projects do not allow for
the vehicle analysis necessary to build reliable models. Here is
presented a procedure using parametric and NN (neural network)
models that enables the generation of vehicle system models based
on normal ECU engine control unit) vehicle measurements. These
models are locally valid and permit pre and follow-up calibrations so
that, only the final calibrations have to be done with the vehicle.
Abstract: Ethnicity identification of face images is of interest in
many areas of application, but existing methods are few and limited.
This paper presents a fusion scheme that uses block-based uniform
local binary patterns and Haar wavelet transform to combine local
and global features. In particular, the LL subband coefficients of the
whole face are fused with the histograms of uniform local binary
patterns from block partitions of the face. We applied the principal
component analysis on the fused features and managed to reduce the
dimensionality of the feature space from 536 down to around 15
without sacrificing too much accuracy. We have conducted a number
of preliminary experiments using a collection of 746 subject face
images. The test results show good accuracy and demonstrate the
potential of fusing global and local features. The fusion approach is
robust, making it easy to further improve the identification at both
feature and score levels.
Abstract: Geopolymer cement was evaluated as wellbore sealing material for carbon dioxide geosequestration application. Curing of cement system in saline water and strength testing in triaxial stress state condition under lateral confinement is relevant to primary cementing in CO2 geosequestration wellbore in saline aquifer. Geopolymer cement was cured in saline water (both at ambient conditions for 28 days and heated (60°C) conditions for 12 hours) and tested for triaxial strength at different levels of lateral confinement. Normal water and few other curing techniques were also studied both for geopolymer and API ‘G’ cement. Results reported were compared to evaluate the suitability of saline water for curing of geopolymer cement. Unconfined compression test results showed higher strength for curing in saline water than normal water. Besides, testing strength under lateral confinement demonstrated the material failure behavior from brittle to plastic.
Abstract: This study analyzes characteristics determining
member’s willingness to invest in cooperatives using ordered logit
model. The data were collected in a field survey among 122
cooperative members in north-central China. The descriptive analysis
of survey evidence suggests that cooperatives in China generally
having poor ability to deliver the processing services related to
product package, grading, and storage, performing worse in
profitability, inability of providing returns to capital and obtaining
agricultural loan. The regression results demonstrate that members’
farm size, their satisfaction with cooperative price preferential
services, attitudes toward cooperative operational scale and
development potential have statistically significant impact on
willingness to invest.
Abstract: In today-s competitive global business environment,
the concept of supply chain management (SCM) continues to become
increasingly market-oriented, shifting the primary driver of the value
chain from supply to demand. Recent recommendations encourage
researchers to focus investigations on the supply chain process
integration (SCPI) capabilities that integrate a focal firm with its
network of suppliers and business customers to create value for it.
However, theoretical and empirical researches pertaining to the
antecedents and consequences of a focal firm-s SCPI capabilities have
been limited and piecemeal. The purpose of this study is to investigate
the critical determinants and consequences of a focal firm-s SCPI
capabilities. We test our proposed research framework using a sample
of 139 sales managers of manufacturing industries in Taiwan, our
research findings show that (1) both perceived business customer-s
power and focal firm-s market-oriented culture positively influences a
focal firm-s SCPI capabilities, and (2) SCPI capabilities positively
influence a focal firm-s SCM performance, both operational and
strategic benefits. Implications for practitioners and researchers and
suggestions for future research are also addressed in this study.
Abstract: Random Access Memory (RAM) is an important
device in computer system. It can represent the snapshot on how the
computer has been used by the user. With the growth of its
importance, the computer memory has been an issue that has been
discussed in digital forensics. A number of tools have been developed
to retrieve the information from the memory. However, most of the
tools have their limitation in the ability of retrieving the important
information from the computer memory. Hence, this paper is aimed
to discuss the limitation and the setback for two main techniques such
as process signature search and process enumeration. Then, a new
hybrid approach will be presented to minimize the setback in both
individual techniques. This new approach combines both techniques
with the purpose to retrieve the information from the process block
and other objects in the computer memory. Nevertheless, the basic
theory in address translation for x86 platforms will be demonstrated
in this paper.
Abstract: The implementation of the new software and hardware-s technologies for tritium processing nuclear plants, and especially those with an experimental character or of new technology developments shows a coefficient of complexity due to issues raised by the implementation of the performing instrumentation and equipment into a unitary monitoring system of the nuclear technological process of tritium removal. Keeping the system-s flexibility is a demand of the nuclear experimental plants for which the change of configuration, process and parameters is something usual. The big amount of data that needs to be processed stored and accessed for real time simulation and optimization demands the achievement of the virtual technologic platform where the data acquiring, control and analysis systems of the technological process can be integrated with a developed technological monitoring system. Thus, integrated computing and monitoring systems needed for the supervising of the technological process will be executed, to be continued with the execution of optimization system, by choosing new and performed methods corresponding to the technological processes within the tritium removal processing nuclear plants. The developing software applications is executed with the support of the program packages dedicated to industrial processes and they will include acquisition and monitoring sub-modules, named “virtually" as well as the storage sub-module of the process data later required for the software of optimization and simulation of the technological process for tritium removal. The system plays and important role in the environment protection and durable development through new technologies, that is – the reduction of and fight against industrial accidents in the case of tritium processing nuclear plants. Research for monitoring optimisation of nuclear processes is also a major driving force for economic and social development.
Abstract: Cluster analysis divides data into groups that are
meaningful, useful, or both. Analysis of biological data is creating a
new generation of epidemiologic, prognostic, diagnostic and
treatment modalities. Clustering of protein sequences is one of the
current research topics in the field of computer science. Linear
relation is valuable in rule discovery for a given data, such as if value
X goes up 1, value Y will go down 3", etc. The classical linear
regression models the linear relation of two sequences perfectly.
However, if we need to cluster a large repository of protein sequences
into groups where sequences have strong linear relationship with
each other, it is prohibitively expensive to compare sequences one by
one. In this paper, we propose a new technique named General
Regression Model Technique Clustering Algorithm (GRMTCA) to
benignly handle the problem of linear sequences clustering. GRMT
gives a measure, GR*, to tell the degree of linearity of multiple
sequences without having to compare each pair of them.
Abstract: Image fusion aims to enhance the perception
of a scene by combining important information captured by
different sensors. Dual-Tree Complex Wavelet (DT-CWT) has been
thouroughly investigated for image fusion, since it takes advantages
of approximate shift invariance and direction selectivity. But it can
only handle limited direction information. To allow a more flexible
directional expansion for images, we propose a novel fusion scheme,
referred to as complex contourlet transform (CCT). It successfully
incorporates directional filter banks (DFB) into DT-CWT. As a result
it efficiently deal with images containing contours and textures,
whereas it retains the property of shift invariance. Experimental
results demonstrated that the method features high quality fusion
performance and can facilitate many image processing applications.
Abstract: This paper presents the use of a semi-classical signal
analysis method that has been developed recently for the analysis of
turbomachinery flow unsteadiness. We will focus on the correlation
between theSemi-Classical Signal Analysis parameters and some
physical parameters in relation with turbomachinery features. To
demonstrate the potential of the proposed approach, a static pressure
signal issued from a rotor/stator interaction of a centrifugal pump is
studied. Several configurations of the pump are compared.
Abstract: The purpose of the study was to determine the amount of Palm Kernel Oil (PKO) extracted from a packed bed of palm kernels in a supercritical fluid extractor using supercritical carbon dioxide (SC-CO2) as an environmental friendly solvent. Further, the study sought to ascertain the values of the overall mass transfer coefficient (K) of PKO evaluation through a mass transfer model, at constant temperature of 50 °C, 60 °C, and 70 °C and pressures range from 27.6 MPa, 34.5 MPa, 41.4 MPa and 48.3 MPa respectively. Finally, the study also seeks to demonstrate the application of the overall mass transfer coefficient values in relation to temperature and pressure. The overall mass transfer coefficient was found to be dependent pressure at each constant temperature of 50 °C, 60 °C and 70 °C. The overall mass transfer coefficient for PKO in a packed bed of palm kernels was found to be in the range of 1.21X 10-4 m min-1 to 1.72 X 10-4 m min-1 for a constant temperature of 50 °C and in the range of 2.02 X 10-4 m min-1 to 2.43 X 10-4 m min-1 for a constant temperature of 60 °C. Similar increasing trend of the overall mass transfer coefficient from 1.77 X 10-4 m min-1 to 3.64 X 10-4 m min-1 was also observed at constant temperature of 70 °C within the same pressure range from 27.6 MPa to 48.3 MPa.
Abstract: Recently, the health of retired National Football
League players, particularly lineman has been investigated. A
number of studies have reported increased cardiometabolic risk,
premature cardiovascular disease and incidence of type 2 diabetes.
Rugby union players have somatotypes very similar to National
Football League players which suggests that rugby players may have
similar health risks. The International Golden Oldies World Rugby
Festival (GORF) provided a unique opportunity to investigate the
demographics of veteran rugby players. METHODOLOGIES: A
cross-sectional, observational study was completed using an online
web-based questionnaire that consisted of medical history and
physiological measures. Data analysis was completed using a one
sample t-test (50yrs) and Chi-square test. RESULTS:
A total of 216 veteran rugby competitors (response rate = 6.8%)
representing 10 countries, aged 35-72 yrs (mean 51.2, S.D. ±8.0),
participated in the online survey. As a group, the incidence of current
smokers was low at 8.8% (avg 72.4 cigs/wk) whilst the percentage
consuming alcohol was high (93.1% (avg 11.2 drinks/wk).
Competitors reported the following top six chronic
diseases/disorders; hypertension (18.6%), arthritis (OA/RA, 11.5%),
asthma (9.3%), hyperlipidemia (8.2%), diabetes (all types, 7.5%) and
gout (6%), there were significant differences between groups with
regard to cancer (all types) and migraines. When compared to the
Australian general population (Australian Bureau of Statistics data,
n=18,000), GORF competitors had a significantly lower incidence of
anxiety (p
Abstract: A novel method of individual level adaptive mutation rate control called the rank-scaled mutation rate for genetic algorithms is introduced. The rank-scaled mutation rate controlled genetic algorithm varies the mutation parameters based on the rank of each individual within the population. Thereby the distribution of the fitness of the papulation is taken into consideration in forming the new mutation rates. The best fit mutate at the lowest rate and the least fit mutate at the highest rate. The complexity of the algorithm is of the order of an individual adaptation scheme and is lower than that of a self-adaptation scheme. The proposed algorithm is tested on two common problems, namely, numerical optimization of a function and the traveling salesman problem. The results show that the proposed algorithm outperforms both the fixed and deterministic mutation rate schemes. It is best suited for problems with several local optimum solutions without a high demand for excessive mutation rates.
Abstract: Procurement is an important component in the field of
operating resource management and e-procurement is the golden key
to optimizing the supply chains system. Global firms are optimistic
on the level of savings that can be achieved through full
implementation of e-procurement strategies. E-procurement is an
Internet-based business process for obtaining materials and services
and managing their inflow into the organization. In this paper, the
subjects of supply chains and e-procurement and its benefits to
organizations have been studied. Also, e-procurement in construction
and its drivers and barriers have been discussed and a framework of
supplier selection in an e-procurement environment has been
demonstrated. This paper also has addressed critical success factors
in adopting e-procurement in supply chains.
Abstract: This paper presents the development and application of an adaptive neuro fuzzy inference system (ANFIS) based intelligent hybrid neuro fuzzy controller for automatic generation control (AGC) of two-area interconnected thermal power system with reheat non linearity. The dynamic response of the system has been studied for 1% step load perturbation in area-1. The performance of the proposed neuro fuzzy controller is compared against conventional proportional-integral (PI) controller, state feedback linear quadratic regulator (LQR) controller and fuzzy gain scheduled proportionalintegral (FGSPI) controller. Comparative analysis demonstrates that the proposed intelligent neuro fuzzy controller is the most effective of all in improving the transients of frequency and tie-line power deviations against small step load disturbances. Simulations have been performed using Matlab®.
Abstract: In this work, we successfully extended one-dimensional differential transform method (DTM), by presenting and proving some theorems, to solving nonlinear high-order multi-pantograph equations. This technique provides a sequence of functions which converges to the exact solution of the problem. Some examples are given to demonstrate the validity and applicability of the present method and a comparison is made with existing results.
Abstract: Full adders are important components in applications
such as digital signal processors (DSP) architectures and
microprocessors. In addition to its main task, which is adding two
numbers, it participates in many other useful operations such as
subtraction, multiplication, division,, address calculation,..etc. In
most of these systems the adder lies in the critical path that
determines the overall speed of the system. So enhancing the
performance of the 1-bit full adder cell (the building block of the
adder) is a significant goal.Demands for the low power VLSI have
been pushing the development of aggressive design methodologies to
reduce the power consumption drastically. To meet the growing
demand, we propose a new low power adder cell by sacrificing the
MOS Transistor count that reduces the serious threshold loss
problem, considerably increases the speed and decreases the power
when compared to the static energy recovery full (SERF) adder. So a
new improved 14T CMOS l-bit full adder cell is presented in this
paper. Results show 50% improvement in threshold loss problem,
45% improvement in speed and considerable power consumption
over the SERF adder and other different types of adders with
comparable performance.
Abstract: Since 1992, year where Hugo de Garis has published
the first paper on Evolvable Hardware (EHW), a period of intense
creativity has followed. It has been actively researched, developed
and applied to various problems. Different approaches have been
proposed that created three main classifications: extrinsic, mixtrinsic
and intrinsic EHW. Each of these solutions has a real interest.
Nevertheless, although the extrinsic evolution generates some
excellent results, the intrinsic systems are not so advanced. This
paper suggests 3 possible solutions to implement the run-time
configuration intrinsic EHW system: FPGA-based Run-Time
Configuration system, JBits-based Run-Time Configuration system
and Multi-board functional-level Run-Time Configuration system.
The main characteristic of the proposed architectures is that they are
implemented on Field Programmable Gate Array. A comparison of
proposed solutions demonstrates that multi-board functional-level
run-time configuration is superior in terms of scalability, flexibility
and the implementation easiness.
Abstract: Repeated observation of a given area over time yields
potential for many forms of change detection analysis. These
repeated observations are confounded in terms of radiometric
consistency due to changes in sensor calibration over time,
differences in illumination, observation angles and variation in
atmospheric effects.
This paper demonstrates applicability of an empirical relative
radiometric normalization method to a set of multitemporal cloudy
images acquired by Resourcesat1 LISS III sensor. Objective of this
study is to detect and remove cloud cover and normalize an image
radiometrically. Cloud detection is achieved by using Average
Brightness Threshold (ABT) algorithm. The detected cloud is
removed and replaced with data from another images of the same
area. After cloud removal, the proposed normalization method is
applied to reduce the radiometric influence caused by non surface
factors. This process identifies landscape elements whose reflectance
values are nearly constant over time, i.e. the subset of non-changing
pixels are identified using frequency based correlation technique. The
quality of radiometric normalization is statistically assessed by R2
value and mean square error (MSE) between each pair of analogous
band.
Abstract: There are reports of gas and oil wells fire due to different accidents. Many different methods are used for fire fighting in gas and oil industry. Traditional fire extinguishing techniques are mostly faced with many problems and are usually time consuming and needs lots of equipments. Besides, they cause damages to facilities, and create health and environmental problems. This article proposes innovative approach in fire extinguishing techniques in oil and gas industry, especially applicable for burning oil wells located offshore. Fire extinguishment employing a turbojet is a novel approach which can help to extinguishment the fire in short period of time. Divergent and convergent turbojets modeled in laboratory scale along with a high pressure flame were used. Different experiments were conducted to determine the relationship between output discharges of trumpet and oil wells. The results were corrected and the relationship between dimensionless parameters of flame and fire extinguishment distances and also the output discharge of turbojet and oil wells in specified distances are demonstrated by specific curves.