Abstract: Continuous measurements and multivariate methods are applied in researching the effects of energy consumption on indoor air quality (IAQ) in a Finnish one-family house. Measured data used in this study was collected continuously in a house in Kuopio, Eastern Finland, during fourteen months long period. Consumption parameters measured were the consumptions of district heat, electricity and water. Indoor parameters gathered were temperature, relative humidity (RH), the concentrations of carbon dioxide (CO2) and carbon monoxide (CO) and differential air pressure. In this study, self-organizing map (SOM) and Sammon's mapping were applied to resolve the effects of energy consumption on indoor air quality. Namely, the SOM was qualified as a suitable method having a property to summarize the multivariable dependencies into easily observable two-dimensional map. Accompanying that, the Sammon's mapping method was used to cluster pre-processed data to find similarities of the variables, expressing distances and groups in the data. The methods used were able to distinguish 7 different clusters characterizing indoor air quality and energy efficiency in the study house. The results indicate, that the cost implications in euros of heating and electricity energy vary according to the differential pressure, concentration of carbon dioxide, temperature and season.
Abstract: In this paper, multiobjective design of multi-machine Power System Stabilizers (PSSs) using Particle Swarm Optimization (PSO) is presented. The stabilizers are tuned to simultaneously shift the lightly damped and undamped electro-mechanical modes of all machines to a prescribed zone in the s-plane. A multiobjective problem is formulated to optimize a composite set of objective functions comprising the damping factor, and the damping ratio of the lightly damped electromechanical modes. The PSSs parameters tuning problem is converted to an optimization problem which is solved by PSO with the eigenvalue-based multiobjective function. The proposed PSO based PSSs is tested on a multimachine power system under different operating conditions and disturbances through eigenvalue analysis and some performance indices to illustrate its robust performance.
Abstract: The effect of muscle loss due to transfemoral
amputation, on energy expenditure of hip joint and individual
residual muscles was simulated. During swing phase of gait, with
each muscle as an ideal force generator, the lower extremity was
modeled as a two-degree of freedom linkage, for which hip and knee
were joints. According to results, muscle loss will not lead to higher
energy expenditure of hip joint, as long as other parameters of limb
remain unaffected. This finding maybe due to the role of biarticular
muscles in hip and knee joints motion. Moreover, if hip flexors are
removed from the residual limb, residual flexors, and if hip extensors
are removed, residual extensors will do more work. In line with the
common practice in transfemoral amputation, this result demonstrates
during transfemoral amputation, it is important to maintain the length
of residual limb as much as possible.
Abstract: This paper addresses the problem of how one can
improve the performance of a non-optimal filter. First the theoretical question on dynamical representation for a given time correlated
random process is studied. It will be demonstrated that for a wide class of random processes, having a canonical form, there exists
a dynamical system equivalent in the sense that its output has the
same covariance function. It is shown that the dynamical approach is more effective for simulating and estimating a Markov and non-
Markovian random processes, computationally is less demanding,
especially with increasing of the dimension of simulated processes.
Numerical examples and estimation problems in low dimensional
systems are given to illustrate the advantages of the approach. A very useful application of the proposed approach is shown for the
problem of state estimation in very high dimensional systems. Here a modified filter for data assimilation in an oceanic numerical model
is presented which is proved to be very efficient due to introducing
a simple Markovian structure for the output prediction error process
and adaptive tuning some parameters of the Markov equation.
Abstract: This study presents an investigation of
electrochemical variables and an application of the optimal
parameters in operating a continuous upflow electrocoagulation
reactor in removing dye. Direct red 23, which is azo-based, was used
as a representative of direct dyes. First, a batch mode was employed
to optimize the design parameters: electrode type, electrode distance,
current density and electrocoagulation time. The optimal parameters
were found to be iron anode, distance between electrodes of 8 mm
and current density of 30 A·m-2 with contact time of 5 min. The
performance of the continuous upflow reactor with these parameters
was satisfactory, with >95% color removal and energy consumption
in the order of 0.6-0.7 kWh·m-3.
Abstract: A numerical study is made of laminar, unsteady flow
behind a rotationally oscillating circular cylinder using a recently
developed higher order compact (HOC) scheme. The stream function
vorticity formulation of Navier-Stokes (N-S) equations in cylindrical
polar coordinates are considered as the governing equations. The
temporal behaviour of vortex formation and relevant streamline
patterns of the flow are scrutinized over broad ranges of two
externally specified parameters namely dimensionless forced
oscillating frequency Sf and dimensionless peak rotation rate αm for
the Reynolds-s number Re = 200. Excellent agreements are found
both qualitatively and quantitatively with the existing experimental
and standard numerical results.
Abstract: In this work, propagation of uncertainty during calibration
process of TRANUS, an integrated land use and transport model
(ILUTM), has been investigated. It has also been examined, through a
sensitivity analysis, which input parameters affect the variation of the
outputs the most. Moreover, a probabilistic verification methodology
of calibration process, which equates the observed and calculated
production, has been proposed. The model chosen as an application is
the model of the city of Grenoble, France. For sensitivity analysis and
uncertainty propagation, Monte Carlo method was employed, and a
statistical hypothesis test was used for verification. The parameters of
the induced demand function in TRANUS, were assumed as uncertain
in the present case. It was found that, if during calibration, TRANUS
converges, then with a high probability the calibration process is
verified. Moreover, a weak correlation was found between the inputs
and the outputs of the calibration process. The total effect of the
inputs on outputs was investigated, and the output variation was found
to be dictated by only a few input parameters.
Abstract: The groundwater is one of the main sources for
sustainability in the United Arab Emirates (UAE). Intensive
developments in Al-Ain area lead to increase water demand, which
consequently reduced the overall groundwater quantity in major
aquifers. However, in certain residential areas within Al-Ain, it has
been noticed that the groundwater level is rising, for example in
Sha-ab Al Askher area. The reasons for the groundwater rising
phenomenon are yet to be investigated. In this work, twenty four
seismic refraction profiles have been carried out along the study
pilot area; as well as field measurement of the groundwater level in
a number of available water wells in the area. The processed
seismic data indicated the deepest and shallowest groundwater
levels are 15m and 2.3 meters respectively. This result is greatly
consistent with the proper field measurement of the groundwater
level. The minimum detected value may be referred to perched
subsurface water which may be associated to the infiltration from
the surrounding water bodies such as lakes, and elevated farms. The
maximum values indicate the accurate groundwater level within the
study area. The findings of this work may be considered as a
preliminary help to the decision makers.
Abstract: Metal matrix composites have been increasingly used
as materials for components in automotive and aerospace industries
because of their improved properties compared with non-reinforced
alloys. During machining the selection of appropriate machining
parameters to produce job for desired surface roughness is of great
concern considering the economy of manufacturing process. In this
study, a surface roughness prediction model using fuzzy logic is
developed for end milling of Al-SiCp metal matrix composite
component using carbide end mill cutter. The surface roughness is
modeled as a function of spindle speed (N), feed rate (f), depth of cut
(d) and the SiCp percentage (S). The predicted values surface
roughness is compared with experimental result. The model predicts
average percentage error as 4.56% and mean square error as 0.0729.
It is observed that surface roughness is most influenced by feed rate,
spindle speed and SiC percentage. Depth of cut has least influence.
Abstract: Machining is an important manufacturing process used to produce a wide variety of metallic parts. Among various machining processes, turning is one of the most important one which is employed to shape cylindrical parts. In turning, the quality of finished product is measured in terms of surface roughness. In turn, surface quality is determined by machining parameters and tool geometry specifications. The main objective of this study is to simultaneously model and optimize machining parameters and tool geometry in order to improve the surface roughness for AISI1045 steel. Several levels of machining parameters and tool geometry specifications are considered as input parameters. The surface roughness is selected as process output measure of performance. A Taguchi approach is employed to gather experimental data. Then, based on signal-to-noise (S/N) ratio, the best sets of cutting parameters and tool geometry specifications have been determined. Using these parameters values, the surface roughness of AISI1045 steel parts may be minimized. Experimental results are provided to illustrate the effectiveness of the proposed approach.
Abstract: Studying alternative raw materials for biodiesel production is of major importance. The use of mixtures with incorporation of wastes is an environmental friendly alternative and might reduce biodiesel production costs. The objective of the present work was: (i) to study biodiesel production using waste frying oil mixed with pork lard and (ii) to understand how mixture composition influences biodiesel quality. Biodiesel was produced by transesterification and quality was evaluated through determination of several parameters according to EN 14214. The weight fraction of lard in the mixture varied from 0 to 1 in 0.2 intervals. Biodiesel production yields varied from 81.7 to 88.0 (wt%), the lowest yields being the ones obtained using waste frying oil and lard alone as raw materials. The obtained products fulfilled most of the determined quality specifications according to European biodiesel quality standard EN 14214. Minimum purity (96.5 wt%) was closely obtained when waste frying oil was used alone and when 0.2% of lard was incorporated in the raw material (96.3 wt%); however, it ranged from 93.9 to 96.3 (wt%) being always close to the limit. From the evaluation of the influence of mixture composition in biodiesel quality, it was possible to establish a model to be used for predicting some parameters of biodiesel resulting from mixtures of waste frying oil with lard when different lard contents are used.
Abstract: The development of biomimetic micro-aerial-vehicles
(MAVs) with flapping wings is the future trend in military/domestic
field. The successful flight of MAVs is strongly related to the
understanding of unsteady aerodynamic performance of low Reynolds
number airfoils under dynamic flapping motion. This study explored
the effects of flapping frequency, stroke amplitude, and the inclined
angle of stroke plane on lift force and thrust force of a bio-inspiration
corrugated airfoil with 33 full factorial design of experiment and
ANOVA analysis. Unsteady vorticity flows over a corrugated thin
airfoil executing flapping motion are computed with time-dependent
two-dimensional laminar incompressible Reynolds-averaged
Navier-Stokes equations with the conformal hybrid mesh. The tested
freestream Reynolds number based on the chord length of airfoil as
characteristic length is fixed of 103. The dynamic mesh technique is
applied to model the flapping motion of a corrugated airfoil. Instant
vorticity contours over a complete flapping cycle clearly reveals the
flow mechanisms for lift force generation are dynamic stall, rotational
circulation, and wake capture. The thrust force is produced as the
leading edge vortex shedding from the trailing edge of airfoil to form a
reverse von Karman vortex. Results also indicated that the inclined
angle is the most significant factor on both the lift force and thrust
force. There are strong interactions between tested factors which mean
an optimization study on parameters should be conducted in further
runs.
Abstract: This work presents the first results from the long-term experiment, which is focused on the impact of intensive rainfall and long period of drought on microbial activities in soil. Fifteen lysimeters were prepared in the area of our interest. This area is a protection zone of underground source of drinking water. These lysimeters were filed with topsoil and subsoil collected in this area and divided into two groups. These groups differ in fertilization and amount of water received during the growing season. Amount of microbial biomass and leaching of mineral nitrogen and phosphates were chosen as main indicators of microbial activities in soil. Content of mineral nitrogen and phosphates was measured in soil solution, which was collected from each lysimeters. Amount of microbial biomass was determined in soil samples that were taken from the lysimeters before and after the long period of drought and intensive rainfall.
Abstract: The aim of this paper is to experimentally discover the workability coefficient of the Inconel 718 material by using a slide turning machining. Two different types of cutting inserts, one made of carbide and the other one made of ceramic, are being used. The purpose is to compare measured results and recommend the appropriate materials and cutting parameters for a machining of the Inconel 718. Furthermore, the durability of inserts with the chosen wear criterion is being compared for different cutting speeds. Machinability of these materials is a crucial characteristic as it allows us to shorten the technological cycle time and increase the machining productivity. And this is of great importance from an economic point of view.
Abstract: A first intermediate roll of Sendzirmir mills was failure
by surface spalling during operation. After analyzing by visual, stereo
microscope, optical microscope, scanning electron microscope,
glow-discharged spectrometer and hardness test, respectively, the
results show that some voids and cracks existed on the contact surface
as well as subsurface. Further examination verified inadequate
hardness and inclusions were responsible for the failure of surface
spalling.
Abstract: In the oil and gas industry, energy prediction can help
the distributor and customer to forecast the outgoing and incoming
gas through the pipeline. It will also help to eliminate any
uncertainties in gas metering for billing purposes. The objective of
this paper is to develop Neural Network Model for energy
consumption and analyze the performance model. This paper
provides a comprehensive review on published research on the
energy consumption prediction which focuses on structures and the
parameters used in developing Neural Network models. This paper is
then focused on the parameter selection of the neural network
prediction model development for energy consumption and analysis
on the result. The most reliable model that gives the most accurate
result is proposed for the prediction. The result shows that the
proposed neural network energy prediction model is able to
demonstrate an adequate performance with least Root Mean Square
Error.
Abstract: Climate change has profound consequences for the agriculture of south-eastern Australia and its climate-induced water shortage in the Murray-Darling Basin. Post Keynesian Economics (PKE) macro-dynamics, along with Kaleckian investment and growth theory, are used to develop an ecological-economic system dynamics model of this complex nonlinear river basin system. The Murray- Darling Basin Simulation Model (MDB-SM) uses the principles of PKE to incorporate the fundamental uncertainty of economic behaviors of farmers regarding the investments they make and the climate change they face, particularly as regards water ecosystem services. MDB-SM provides a framework for macroeconomic policies, especially for long-term fiscal policy and for policy directed at the sustainability of agricultural water, as measured by socio-economic well-being considerations, which include sustainable consumption and investment in the river basin. The model can also reproduce other ecological and economic aspects and, for certain parameters and initial values, exhibit endogenous business cycles and ecological sustainability with realistic characteristics. Most importantly, MDBSM provides a platform for the analysis of alternative economic policy scenarios. These results reveal the importance of understanding water ecosystem adaptation under climate change by integrating a PKE macroeconomic analytical framework with the system dynamics modelling approach. Once parameterised and supplied with historical initial values, MDB-SM should prove to be a practical tool to provide alternative long-term policy simulations of agricultural water and socio-economic well-being.
Abstract: The concept of order reduction by least-squares moment matching and generalised least-squares methods has been extended about a general point ?a?, to obtain the reduced order models for linear, time-invariant dynamic systems. Some heuristic criteria have been employed for selecting the linear shift point ?a?, based upon the means (arithmetic, harmonic and geometric) of real parts of the poles of high order system. It is shown that the resultant model depends critically on the choice of linear shift point ?a?. The validity of the criteria is illustrated by solving a numerical example and the results are compared with the other existing techniques.
Abstract: This study aims to initiate sustainable water management for tourist accommodations in Amphawa, Samut Songkram Province, Thailand. Wastewater generated by tourist accommodation was conducted in 10 homestays and resorts in Amphawa during August – October, 2011. The prominent parameters which are of pH, Dissolved Oxygen (DO), Biochemical Oxygen Demand (BOD), Fat Oil and Grease (FOG), Nitrate (No3-), and Phosphate (PO43-) were conducted monthly. The results revealed that some parameters were over national water quality standard (Class II). Especially, 90% of tourist accommodations have been recorded that FOG was over the standard of wastewater quality from accommodation (group I: total room of accommodation less than 200 rooms). Therefore, grease trap and natural treatment should be utilized in tourist accommodations in order to reduce the discharged of fat, oil, and grease from tourism activities. In addition, number of tourists also relate statistically with BOD and Nitrate at 0.05 level of significance.
Abstract: An evolutionary computing technique for solving initial value problems in Ordinary Differential Equations is proposed in this paper. Neural network is used as a universal approximator while the adaptive parameters of neural networks are optimized by genetic algorithm. The solution is achieved on the continuous grid of time instead of discrete as in other numerical techniques. The comparison is carried out with classical numerical techniques and the solution is found with a uniform accuracy of MSE ≈ 10-9 .