Abstract: Nowadays, energy dissipation devices are commonly
used in structures. High rate of energy absorption during earthquakes
is the benefit of using such devices, which results in damage
reduction of structural elements, specifically columns. The hysteretic
damping capacity of energy dissipation devices is the key point that it
may adversely make analysis and design process complicated. This
effect may be generally represented by Equivalent Viscous Damping
(EVD). The equivalent viscous damping might be obtained from the
expected hysteretic behavior regarding to the design or maximum
considered displacement of a structure. In this paper, the hysteretic
damping coefficient of a steel Moment Resisting Frame (MRF),
which its performance is enhanced by a Buckling Restrained Brace
(BRB) system has been evaluated. Having foresight of damping
fraction between BRB and MRF is inevitable for seismic design
procedures like Direct Displacement-Based Design (DDBD) method.
This paper presents an approach to calculate the damping fraction for
such systems by carrying out the dynamic nonlinear time history
analysis (NTHA) under harmonic loading, which is tuned to the
natural system frequency. Two MRF structures, one equipped with
BRB and the other without BRB are simultaneously studied.
Extensive analysis shows that proportion of each system damping
fraction may be calculated by its shear story portion. In this way,
contribution of each BRB in the floors and their general contribution
in the structural performance may be clearly recognized, in advance.
Abstract: Anammox is a novel and promising technology that has changed the traditional concept of biological nitrogen removal. The process facilitates direct oxidation of ammonical nitrogen under anaerobic conditions with nitrite as an electron acceptor without addition of external carbon sources. The present study investigated the feasibility of Anammox Hybrid Reactor (AHR) combining the dual advantages of suspended and attached growth media for biodegradation of ammonical nitrogen in wastewater. Experimental unit consisted of 4 nos. of 5L capacity AHR inoculated with mixed seed culture containing anoxic and activated sludge (1:1). The process was established by feeding the reactors with synthetic wastewater containing NH4-H and NO2-N in the ratio 1:1 at HRT (hydraulic retention time) of 1 day. The reactors were gradually acclimated to higher ammonium concentration till it attained pseudo steady state removal at a total nitrogen concentration of 1200 mg/l. During this period, the performance of the AHR was monitored at twelve different HRTs varying from 0.25-3.0 d with increasing NLR from 0.4 to 4.8 kg N/m3d. AHR demonstrated significantly higher nitrogen removal (95.1%) at optimal HRT of 1 day. Filter media in AHR contributed an additional 27.2% ammonium removal in addition to 72% reduction in the sludge washout rate. This may be attributed to the functional mechanism of filter media which acts as a mechanical sieve and reduces the sludge washout rate many folds. This enhances the biomass retention capacity of the reactor by 25%, which is the key parameter for successful operation of high rate bioreactors. The effluent nitrate concentration, which is one of the bottlenecks of anammox process was also minimised significantly (42.3-52.3 mg/L). Process kinetics was evaluated using first order and Grau-second order models. The first-order substrate removal rate constant was found as 13.0 d-1. Model validation revealed that Grau second order model was more precise and predicted effluent nitrogen concentration with least error (1.84±10%). A new mathematical model based on mass balance was developed to predict N2 gas in AHR. The mass balance model derived from total nitrogen dictated significantly higher correlation (R2=0.986) and predicted N2 gas with least error of precision (0.12±8.49%). SEM study of biomass indicated the presence of heterogeneous population of cocci and rod shaped bacteria of average diameter varying from 1.2-1.5 mm. Owing to enhanced NRE coupled with meagre production of effluent nitrate and its ability to retain high biomass, AHR proved to be the most competitive reactor configuration for dealing with nitrogen laden wastewater.
Abstract: Objective: Sharing devastating news with patients is
often considered the most difficult task of doctors. This study aimed
to explore patients’ perceptions of receiving bad news including
which features improve the experience and which areas need refining. Methods: A questionnaire was written based on the steps of the
SPIKES model for breaking bad new. 20 patients receiving treatment
for a hematological malignancy completed the questionnaire. Results: Overall, the results are promising as most patients praised
their consultation. ‘Poor’ was more commonly rated by women and
participants aged 45-64. The main differences between the ‘excellent’
and ‘poor’ consultations include the doctor’s sensitivity and checking
the patients’ understanding. Only 35% of patients were asked their
existing knowledge and 85% of consultations failed to discuss the
impact of the diagnosis on daily life. Conclusion: This study agreed with the consensus of existing
literature. The commended aspects include consultation set-up and
information given. Areas patients felt needed improvement include
doctors determining the patient’s existing knowledge and checking
new information has been understood. Doctors should also explore
how the diagnosis will affect the patient’s life. With a poorer
prognosis, doctors should work on conveying appropriate hope. The
study was limited by a small sample size and potential recall bias.
Abstract: The present study is a functional analysis of the
relationship between castes which indicates the dynamics of the caste
structure in the rural setting. The researcher has tried to show both
the cooperation and competition on important ceremonial and social
occasions. The real India exists in the villages, so we need to know
about their solidarity and also what the village life is and has been
shaping into. We need to emphasize a microcosmic study of Indian
rural life. Furthermore, caste integration is an acute problem country
faces today. To resolve this we are required to know the dynamics of
behavior of the people of different castes and for the study of the
caste dynamics a study of caste relations are needed. The present
study is an attempt in this direction.
Abstract: This research was planned in order to study the effect
of drought stress and different levels of Superabsorbent and their
effect on grain yield, biologic yield and harvest index. In this study, 3
different depths of irrigation were considered as the main treatment
I1, I2, I3 as 100, 75 and 50 percent of water requirement of plants
respectively and different levels of Superabsorbent were used as
secondary treatment (S0, S1, S2 and S3, equal to 0 (control), 15, 30
and 45 gr/m2 respectively). According to the results, independent
effects of irrigation and Superabsorbent treatments at 1% level on
biologic and grain yield of corn were significant. In addition,
independent effect of irrigation treatments at 5% level on harvest
index was significant. But independent effect of Superabsorbent
treatments on harvest index was not significant.
Abstract: Leishmaniasis is the collective name for a number of
diseases caused by protozoan flagellates of the genus Leishmania,
which is transmitted by Phlebotomine sandfly, the disease has diverse
clinical manifestations and found in many areas of the world,
particularly in Africa, Latin America, South and Central Asia, the
Mediterranean basin and the Middle East. This study was done to
assess primary health care physicians’ knowledge (PHP) and attitude
about leishmaniasis and to assess awareness of local inhabitants
about the disease and its vector in four areas in west Alexandria,
Egypt. It is a cross sectional survey that was conducted in four PHC
units in west Alexandria. All physicians currently working in these
units during the study period were invited to participate in the study;
only 20 PHP completed the questionnaire. 60 local inhabitants were
selected randomly from the four areas of the study, 15 from each
area; Data was collected through two different specially designed
questionnaires. Results showed that 11 (55%) percent of the
physicians had satisfactory knowledge; they answered more than 9
(60%) questions out of a total 14 questions about leishmaniasis and
sandfly. On the other hand when attitude of the primary health care
physicians about leishmaniasis was measured, results showed that 17
(85%) had good attitude and 3 (15%) had poor attitude. The second
questionnaire showed that the awareness of local inhabitants about
leishmaniasis and sandfly as a vector of the disease is poor and needs
to be corrected. (90%) of the interviewed inhabitants had not heard
about leishmaniasis, Only 3 (5%) of them said they know sandfly and
its role in transmission of leishmaniasis. Thus we conclude that
knowledge and attitudes of physicians are acceptable. However, there
is, room for improvement and could be done through formal training
courses and distribution of guidelines. In addition to raising the
awareness of primary health care physicians about the importance of
early detection and notification of cases of leishmaniasis, health
education for raising awareness of the public regarding the vector and
the disease is necessary because related studies have demonstrated
that for inhabitants to take enough protective measures against the
vector, they should perceive that it is responsible for causing a
disease.
Abstract: This study intends to show the influence of the
hydrolytic degradation on the properties of the e-PTFE/NOMEX®
membranes used in fire-protective clothing. The modification of
water vapour permeability, morphology and chemical structure was
examined by MOCON Permatran, electron microscopy scanning
(SEM), and ATR-FTIR, respectively. A decrease in permeability to
water vapour of the aged samples was observed following closure of
transpiration pores. Analysis of fiber morphology indicates the
appearance of defects at the fibers surface with the presence of micro
cavities. ATR-FTIR analysis reveals the presence of a new absorption
band attributed to carboxylic acid terminal groups generated during
the amide bond hydrolysis.
Abstract: Cole-Cole parameters of 40 post-menopausal women
are compared with their DEXA bone mineral density measurements.
Impedance characteristics of four extremities are compared; left and
right extremities are statistically same, but lower extremities are
statistically different than upper ones due to their different fat
content. The correlation of Cole-Cole impedance parameters to bone
mineral density (BMD) is observed to be higher for dominant arm.
With the post-menopausal population, ANOVA tests of the dominant
arm characteristic frequency, as a predictor for DEXA classified
osteopenic and osteoporic population around lumbar spine, is
statistically very significant. When used for total lumbar spine
osteoporosis diagnosis, the area under the Receiver Operating Curve
of the characteristic frequency is 0.830, suggesting that the Cole-Cole
plot characteristic frequency could be a useful diagnostic parameter
when integrated into standard screening methods for osteoporosis.
Moreover, the characteristic frequency can be directly measured by
monitoring frequency driven angular behavior of the dominant arm
without performing any complex calculation.
Abstract: Communicating users' needs, goals and problems help
designers and developers overcome challenges faced by end users.
Personas are used to represent end users’ needs. In our research,
creating personas allowed the following questions to be answered:
Who are the potential user groups? What do they want to achieve by
using the service? What are the problems that users face? What
should the service provide to them? To develop realistic personas, we
conducted a focus group discussion with undergraduate and graduate
students and also interviewed a university librarian. The personas
were created to help evaluating the Institutional Repository that is
based on the DSpace system. The profiles helped to communicate
users' needs, abilities, tasks, and problems, and the task scenarios
used in the heuristic evaluation were based on these personas. Four
personas resulted of a focus group discussion with undergraduate and
graduate students and from interviewing a university librarian. We
then used these personas to create focused task-scenarios for a
heuristic evaluation on the system interface to ensure that it met
users' needs, goals, problems and desires. In this paper, we present
the process that we used to create the personas that led to devise the
task scenarios used in the heuristic evaluation as a follow up study of
the DSpace university repository.
Abstract: Fiber Reinforced Polymer (FRP) is a composite material with exceptional properties that are capable to replace conventional steel reinforcement in reinforced and pre-stressed concrete structures. However, the main obstacle for their wide use in pre-stressed concrete application is the anchorage system. Due to the weakness of FRP in the transverse direction, the pre-stressing capacity of FRP bars are limited. This paper investigates the modification of the conventional wedge anchorage system to be used for stressing of FRP bars in pre-stressed applications. Epoxy adhesive material with glass FRP (GFRP) bars and conventional steel wedge were used in this paper. The GFRP bars are encased with epoxy at the anchor zone and the wedge system was used in pull-out test. The results showed a loading capacity of 47.6 kN which is 69% of the bar ultimate capacity. Additionally, nylon wedge was made with the same dimensions of the steel wedge and tested for GFRP bars without epoxy layer. The nylon wedge showed a loading capacity of 19.7 kN which is only 28.5% of the ultimate bar capacity.
Abstract: The properties of hollow sandcrete blocks produced in
Minna, Nigeria are presented. Sandcrete block is made of cement,
water and sand binded together in certain mix proportions. For the
purpose of this work, fifty (50) commercial sandcrete block industries
were visited in Minna, Nigeria to obtain block samples and
aggregates used for the manufacture, and to take inventory of the mix
composition and the production process. Sieve analysis tests were
conduction on the soil sample from various block industries to
ascertain their quality to be used for block making. The mix ratios
were also investigated. Five (5) nine inches (9’’ or 225mm) blocks
were obtained from each block industry and tested for dimensional
compliance and compressive strength. The results of the soil test
shows that the grading fall within the limit for natural aggregate and
can easily are used to obtain workable mix. Physical examinations of
the block sizes show slight deviation from the standard requirement
in NIS 87:2000. Compressive strength of hollow sandcrete blocks in
range of 0.12 N/mm2 to 0.54 N/mm2 was obtained which is below the
recommendable value of 3.45 N/mm2 for load bearing hollow
sandcrete blocks. This indicates that these blocks are below the
standard for load-bearing sandcrete blocks and cannot be used as load
bearing walling units. The mix composition also indicated low
cement content resulting in low compressive strength. Most of the
commercial block industries visited does not take curing very serious.
Water were only sprinkled ones or twice before the blocks were
stacked and made readily available for sale. It is recommended that a
mix ratio of 1:4 to 1:6 should be used for the production of sandcrete
blocks and proper curing practice should be adhered. Blocks should
also be cured for 14 days before making them available for
consumers.
Abstract: The research aims to study the association between
job satisfaction, motivation and the five factors of organizational
citizenship behavior (i.e. Altruism, Conscientiousness,
Sportsmanship, Courtesy and Civic virtue) among Public Sector
Employees in Pakistan. In this research Structure Equation Modeling
with confirmatory factor analysis was used to test the relationship
between two independent and five dependent variables. Data was
collected through questionnaire survey from 152 Public Servants
Working in Gujrat District-Pakistan in different capacities. Stratified
Random Sampling Technique was used to conduct this survey. The
results of the study indicate that five factors of OCB have positive
significant relation with both motivation and job satisfaction except
the relationship of Civic Virtue with Motivation. The research
findings implicate that factors other than motivation and job
satisfaction may also affect OCB. Likewise, all the five factors of
OCB may not be present in all populations. Thus, Managers must
concentrate on increasing motivation and job satisfaction to increase
OCB. Furthermore, the present research gives a direction to future
researchers to use more independent variables (e.g. Culture,
leadership, workplace environment, various job attitudes, types of
motivation, etc.) on different types of populations with larger sample
size in order to find the reasons behind insignificant relationship of
civic virtue with Motivation in the research in hand and to generalize
the tested model.
Abstract: Background: Diabetic sensorimotor polyneuropathy
(DSP) is one of the most common microvascular complications of
type 2 diabetes. Loss of sensation is thought to contribute to a lack of
static and dynamic stability and increased risk of falling. Purpose:
The purpose of this study was to compare the effects of low-level
laser (LLL) and monochromatic near-infrared photo energy (MIRE)
on pain, cutaneous sensation, static stability, and index of lower limb
blood flow in diabetic patients with peripheral neuropathy. Methods:
Forty diabetic patients with peripheral neuropathy were recruited for
participation in this study. They were divided into two groups: The
MIRE group, which contained 20 patients, and the LLL group, which
contained 20 patients. All patients who participated in the study had
been subjected to various physical assessment procedures, including
pain, cutaneous sensation, Doppler flow meter, and static stability
assessments. The baseline measurements were followed by treatment
sessions that were conducted twice a week for six successive weeks.
Results: The statistical analysis of the data revealed significant
improvement of pain in both groups, with significant improvement in
cutaneous sensation and static balance in the MIRE group compared
to the LLL group; on the other hand, the results showed no
significant differences in lower limb blood flow between the groups.
Conclusion: LLL and MIRE can improve painful symptoms in
patients with diabetic neuropathy. On the other hand, MIRE is also
useful in improving cutaneous sensation and static stability in
patients with diabetic neuropathy.
Abstract: Adequate analgesia following caesarean section
decreases morbidity, hastens ambulation, improves patient outcome
and facilitates care of the newborn. Intrathecal magnesium, an
NMDA antagonist, has been shown to prolong analgesia without
significant side effects in healthy parturients. The aim of this study
was to evaluate the onset and duration of sensory and motor block,
hemodynamic effect, postoperative analgesia, and adverse effects of
magnesium or fentanyl given intrathecally with hyperbaric 0.5%
bupivacaine in patients with mild preeclampsia undergoing caesarean
section. Sixty women with mild preeclampsia undergoing elective
caesarean section were included in a prospective, double blind,
controlled trial. Patients were randomly assigned to receive spinal
anesthesia with 2 mL 0.5% hyperbaric bupivacaine with 12.5 μg
fentanyl (group F) or 0.1 ml of 50% magnesium sulphate (50 mg)
(group M) with 0.15ml preservative free distilled water. Onset,
duration and recovery of sensory and motor block, time to maximum
sensory block, duration of spinal anaesthesia and postoperative
analgesic requirements were studied. Statistical comparison was
carried out using the Chi-square or Fisher’s exact tests and
Independent Student’s t-test where appropriate. The onset of both
sensory and motor block was slower in the magnesium group. The
duration of spinal anaesthesia (246 vs. 284) and motor block (186.3
vs. 210) were significantly longer in the magnesium group. Total
analgesic top up requirement was less in group M. Hemodynamic
parameters were similar in both the groups. Intrathecal magnesium
caused minimal side effects. Since Fentanyl and other opioid
congeners are not available throughout the country easily,
magnesium with its easy availability and less side effect profile can
be a cost effective alternative to fentanyl in managing pregnancy
induced hypertension (PIH) patients given along with Bupivacaine
intrathecally in caesarean section.
Abstract: The increasing volume of solid waste generated,
collected and disposed daily complicate adequate management of
solid waste by relevant agency like Niger State Environmental
Protection Agency (NISEPA). In addition, the impacts of solid waste
on the natural environment and human livelihood require
identification of cost-effective ways for sustainable municipal waste
management in Nigeria. These signal the need for identifying
environment-friendly initiative and local solution to address the
problem of municipal solid waste. A research field was secured at
Pago, Minna, Niger State which is located in the guinea savanna belt
of Nigeria, within longitude 60 361 4311 - 4511 and latitude 90 291
37.6111 - .6211 N. Poultry droppings, decomposed household waste
manure and NPK treatments were used. The experimental field was
divided into three replications and four (4) treatments on each
replication making a total of twelve (12) plots. The treatments were
allotted using Randomized Complete Block Design (RCBD) and
Data collected was analyzed using SPSS software and RCBD. The
result depicts variation in plant height and number of leaves at 50%
flowering; Poultry dropping records the highest height while the
number of leaves for waste manure competes fairly well with NPK
treatment. Similarly, the varying treatments significantly increase
vegetable yield, as the control (non-treatment) records the least yield
for the three vegetable samples. Adoption of this organic manure for
cultivation does not only enhance environment quality and attainment
of food security but will contribute to local economic development,
poverty alleviation as well as social inclusion.
Abstract: The aim of the current work was to employ the finite
element method to model a slab, with a small hole across its width,
undergoing plastic plane strain deformation. The computational
model had, however, to be validated by comparing its results with
those obtained experimentally. Since they were in good agreement,
the finite element method can therefore be considered a reliable tool
that can help gain better understanding of the mechanism of ductile
failure in structural members having stress raisers. The finite element
software used was ANSYS, and the PLANE183 element was utilized.
It is a higher order 2-D, 8-node or 6-node element with quadratic
displacement behavior. A bilinear stress-strain relationship was used
to define the material properties, with constants similar to those of the
material used in the experimental study. The model was run for
several tensile loads in order to observe the progression of the plastic
deformation region, and the stress concentration factor was
determined in each case. The experimental study involved employing the visioplasticity
technique, where a circular mesh (each circle was 0.5 mm in
diameter, with 0.05 mm line thickness) was initially printed on the
side of an aluminum slab having a small hole across its width.
Tensile loading was then applied to produce a small increment of
plastic deformation. Circles in the plastic region became ellipses,
where the directions of the principal strains and stresses coincided
with the major and minor axes of the ellipses. Next, we were able to
determine the directions of the maximum and minimum shear
stresses at the center of each ellipse, and the slip-line field was then
constructed. We were then able to determine the stress at any point in
the plastic deformation zone, and hence the stress concentration
factor. The experimental results were found to be in good agreement
with the analytical ones.
Abstract: This survey paper shows the recent state of model
comparison as it’s applies to Model Driven engineering. In Model
Driven Engineering to calculate the difference between the models is
a very important and challenging task. There are number of tasks
involved in model differencing that firstly starts with identifying and
matching the elements of the model. In this paper, we discuss how
model matching is accomplished, the strategies, techniques and the
types of the model. We also discuss the future direction. We found
out that many of the latest model comparison strategies are geared
near enabling Meta model and similarity based matching. Therefore
model versioning is the most dominant application of the model
comparison. Recently to work on comparison for versioning has
begun to deteriorate, giving way to different applications. Ultimately
there is wide change among the tools in the measure of client exertion
needed to perform model comparisons, as some require more push to
encourage more sweeping statement and expressive force.
Abstract: The goal of the modern education system is to prepare
students to be able to adapt to ever-changing life situations. They
must be able to acquire required knowledge independently; apply
such knowledge in practice to solve various problems by using
modern technologies; think critically and creatively; competently use
information; be communicative, work in a team; and develop their
own moral values, intellect and cultural awareness. As a result, the
status of education significantly increases; new requirements to its
quality have been formed. In recent years the competency-based
approach in education has become of significant interest. This
approach is a strengthening of applied and practical characteristics of
a school education and leads to the forming of the key students’
competencies which define their success in future life. In this article,
the authors’ attention focuses on a range of key competencies,
educational, informational and communicative and on the possibility
to develop such competencies via STEM education. This research
shows the change in students’ attitude towards scientific disciplines
such as mathematics, general science, technology and engineering as
a result of STEM education. Two staged analyzed questionnaires
completed by students of forms II to IV in the republic of Trinidad
and Tobago allowed the authors to categorize students between two
levels that represent students’ attitude to various disciplines. The
significance of differences between selected levels was confirmed
with the use of Pearson’s chi-squared test. In summary, the analysis
of obtained data makes it possible to conclude that STEM education
has a great potential for development of core students’ competencies
and encourage the development of positive student attitude towards
the above mentioned above scientific disciplines.
Abstract: This paper seeks to assess the implications of
insurance to foreign direct investment inflow in Nigeria. Multiple
linear regression technique and correlation matrix test were employed
to measure the extent to which foreign direct investment was
influenced. The result showed that insurance premium (IP), asset size
of insurance industry (AS), and total investment of the industry (TI)
impacted significantly and positively on foreign direct investment
inflow in Nigeria. There should be effective risk transfer mechanism
and financial intermediation, which gives the investor confidence in
the risk management strength of the host country.
Abstract: Electrohydraulic servo system have been used in
industry in a wide number of applications. Its dynamics are highly
nonlinear and also have large extent of model uncertainties and
external disturbances. In this paper, a robust back-stepping control
(RBSC) scheme is proposed to overcome the problem of disturbances
and system uncertainties effectively and to improve the tracking
performance of EHS systems. In order to implement the proposed
control scheme, the system uncertainties in EHS systems are
considered as total leakage coefficient and effective oil volume. In
addition, in order to obtain the virtual controls for stabilizing system,
the update rule for the system uncertainty term is induced by
the Lyapunov control function (LCF). To verify the performance and
robustness of the proposed control system, computer simulation of
the proposed control system using Matlab/Simulink Software
is executed. From the computer simulation, it was found that the
RBSC system produces the desired tracking performance and has
robustness to the disturbances and system uncertainties of EHS
systems.