Abstract: In this paper we present the design of an optical
device based on a Herriott multi-pass cell fabricated on a small sized
acrylic slab for heat flux measurements using the deflection of a laser
beam propagating inside the cell. The beam deflection is produced by
the heat flux conducted to the acrylic slab due to a gradient in the
refractive index. The use of a long path cell as the sensitive element
in this measurement device, gives the possibility of high sensitivity
within a small size device. We present the optical design as well as
some experimental results in order to validate the device’s operation
principle.
Abstract: The main idea of this work is to investigate the effect
of knitted fabrics characteristics on moisture management properties.
Wetting and transport properties of single jersey, Rib 1&1 and
English Rib fabrics made out of cotton and blended Cotton/Polyester
yarns were studied. The dynamic water sorption of fabrics was
investigated under same isothermal and terrestrial conditions at
20±2°C-65±4% by using the Moisture Management Tester (MMT)
which can be used to quantitatively measure liquid moisture transfer
in one step in a fabric in multidirections: Absorption rate, moisture
absorbing time of the fabric's inner and outer surfaces, one-way
transportation capability, the spreading/drying rate, the speed of
liquid moisture spreading on fabric's inner and outer surfaces are
measured, recorded and discussed. The results show that fabric’s
composition and knit’s structure have a significant influence on those
phenomena.
Abstract: The Adaptive Line Enhancer (ALE) is widely used for
enhancing narrowband signals corrupted by broadband noise. In this
paper, we propose novel ALE methods to improve the enhancing
capability. The proposed methods are motivated by the fact that the
output of the ALE is a fine estimate of the desired narrowband signal
with the broadband noise component suppressed. The proposed
methods preprocess the input signal using ALE filter to regenerate a
finer input signal. Thus the proposed ALE is driven by the input signal
with higher signal-to-noise ratio (SNR). The analysis and simulation
results are presented to demonstrate that the proposed ALE has better
performance than conventional ALE’s.
Abstract: This paper explores and provides substantiated
evidence on the usage patterns of Information and Communication
Technologies (ICTs) by female users at Vhembe District in Limpopo-
Province, South Africa. The study presents a comprehensive picture
on the usage of ICTs from female users’ perspective. The
significance of this study stems from the need to assess the role,
relevance and usage patterns of ICTs such as smartphones,
computers, laptops, and iPods, the internet and social networking
sites among females following the developments of new media
technologies in society. The objective of the study is to investigate
the usability and accessibility of ICTs to empower female users in
South Africa. The study used quantitative and qualitative research
methods to determine the major ideas, perceptions and usage patterns
of ICTs by users. Data collection involved the use of structured selfadministered
questionnaire from two groups of respondents who
participated in this study. Thus, (n=50) female students at the
University of Venda provided their ideas and perceptions about the
usefulness and usage patterns of ICTs such as smartphones, the
Internet and computers at the university level, whereas, the second
group were (n=50) learners from Makhado Comprehensive School
who provided their perceptions and ideas about the use of ICTs at the
high school level. The researcher also noted that the findings of the
study were useful as a guideline and model for ICT intervention that
could work as an empowerment to women in South Africa. It was
observed that the central purpose of ICTs among female users was to
search for information regarding assignment writing, conducting
research, dating, exchanging ideas and networking with friends and
relatives. This was demonstrated by a high number of females who
used ICTs for e-learning (62%) and social purposes (85%).
Therefore, the study revealed that most females used ICTs for social
purposes and accessing the internet rather than for entertainment, a
gesture that provides an opportune space to empower rural women in
South Africa.
Abstract: Wire Electric Discharge Machining (WEDM) is
thermal machining process capable of machining very hard
electrically conductive material irrespective of their hardness.
WEDM is being widely used to machine micro scale parts with the
high dimensional accuracy and surface finish. The objective of this
paper is to optimize the process parameters of wire EDM to fabricate
the micro channels and to calculate the surface finish and material
removal rate of micro channels fabricated using wire EDM. The
material used is aluminum 6061 alloy. The experiments were
performed using CNC wire cut electric discharge machine. The effect
of various parameters of WEDM like pulse on time (TON) with the
levels (100, 150, 200), pulse off time (TOFF) with the levels (25, 35,
45) and current (IP) with the levels (105, 110, 115) were investigated
to study the effect on output parameter i.e. Surface Roughness and
Material Removal Rate (MRR). Each experiment was conducted
under different conditions of pulse on time, pulse off time and peak
current. For material removal rate, TON and Ip
were the most significant process parameter. MRR increases with the increase in
TON and Ip and decreases with the increase in TOFF. For surface
roughness, TON and Ip have the maximum effect and TOFF was found
out to be less effective.
Abstract: In internet of things (IoT) system, the communication
scheme with reliability and low power is required to connect a
terminal. Cooperative communication can achieve reliability and
lower power than multiple-input multiple-output (MIMO) system.
Cooperative communication increases the reliability with low
power, but decreases a throughput. It has a weak point that the
communication throughput is decreased. In this paper, a novel scheme
is proposed to increase the communication throughput. The novel
scheme is a transmission structure that increases transmission rate.
A decoding scheme according to the novel transmission structure is
proposed. Simulation results show that the proposed scheme increases
the throughput without bit error rate (BER) performance degradation.
Abstract: A biosphere reserve is developed to create harmony
amongst economic development, community development, and
environmental protection, through partnership between human and
nature. Giam Siak Kecil Bukit Batu Biosphere Reserve (GSKBB BR)
in Riau Province, Indonesia, is unique in that it has peat soil
dominating the area, many springs essential for human livelihood,
high biodiversity. Furthermore, it is the only biosphere reserve
covering privately managed production forest areas. In this research, we aimed at analyzing the threat of deforestation
and forest fire, and the potential of CO2 emission at GSKBB BR. We
used Landsat image, arcView software, and ERDAS IMAGINE 8.5
Software to conduct spatial analysis of land cover and land use
changes, calculated CO2 emission based on emission potential from
each land cover and land use type, and exercised simple linear
regression to demonstrate the relation between CO2 emission
potential and deforestation. The result showed that, beside in the buffer zone and transition
area, deforestation also occurred in the core area. Spatial analysis of
land cover and land use changes from years 2010, 2012, and 2014
revealed that there were changes of land cover and land use from
natural forest and industrial plantation forest to other land use types,
such as garden, mixed garden, settlement, paddy fields, burnt areas,
and dry agricultural land. Deforestation in core area, particularly at
the Giam Siak Kecil Wildlife Reserve and Bukit Batu Wildlife
Reserve, occurred in the form of changes from natural forest in to
garden, mixed garden, shrubs, swamp shrubs, dry agricultural land,
open area, and burnt area. In the buffer zone and transition area,
changes also happened, what once swamp forest changed into garden,
mixed garden, open area, shrubs, swamp shrubs, and dry agricultural
land. Spatial analysis on land cover and land use changes indicated
that deforestation rate in the biosphere reserve from 2010 to 2014 had
reached 16 119 ha/year. Beside deforestation, threat toward the
biosphere reserve area also came from forest fire. The occurrence of forest fire in 2014 had burned 101 723 ha of the
area, in which 9 355 ha of core area, and 92 368 ha of buffer zone
and transition area. Deforestation and forest fire had increased CO2
emission as much as 24 903 855 ton/year.
Abstract: We report the design and characterization of ultra high
quality factor filter based on one-dimensional photonic-crystal Thue-
Morse sequence structure. The behavior of aperiodic array of
photonic crystal structure is numerically investigated and we show
that by changing the angle of incident wave, desired wavelengths
could be tuned and a tunable filter is realized. Also it is shown that
high quality factor filter be achieved in the telecommunication
window around 1550 nm, with a device based on Thue-Morse
structure. Simulation results show that the proposed structure has a
quality factor more than 100000 and it is suitable for DWDM
communication applications.
Abstract: Measuring the Electrocardiogram (ECG) signal is an
essential process for the diagnosis of the heart diseases. The ECG
signal has the information of the degree of how much the heart
performs its functions. In medical diagnosis and treatment systems,
Decision Support Systems processing the ECG signal are being
developed for the use of clinicians while medical examination. In this
study, a modular wireless ECG (WECG) measuring and recording
system using a single board computer and e-Health sensor platform
is developed. In this designed modular system, after the ECG signal
is taken from the body surface by the electrodes first, it is filtered and
converted to digital form. Then, it is recorded to the health database
using Wi-Fi communication technology. The real time access of the
ECG data is provided through the internet utilizing the developed
web interface.
Abstract: High temperature Fischer-Tropsch synthesis process
use fixed fluidized bed as a reactor. In order to understand the flow
behavior in the fluidized bed better, the research of how the radial
velocity affects the entire flow field is necessary. Laser Doppler
Velocimetry (LDV) was used to study the radial velocity distribution
along the diameter direction of the cross-section of the particle in a
fixed fluidized bed. The velocity in the cross-section is fluctuating
within a small range. The direction of the speed is a random
phenomenon. In addition to r/R is 1, the axial velocity are more than 6
times of the radial velocity, the radial velocity has little impact on the
axial velocity in a fixed fluidized bed.
Abstract: The availability to deploy mobile applications for
health care is increasing daily thru different mobile app stores. But
within these capabilities the number of hacking attacks has also
increased, in particular into medical mobile applications. The security
vulnerabilities in medical mobile apps can be triggered by errors in
code, incorrect logic, poor design, among other parameters. This is
usually used by malicious attackers to steal or modify the users’
information. The aim of this research is to analyze the vulnerabilities
detected in mobile medical apps according to risk factor standards
defined by OWASP in 2014.
Abstract: A new approach has been developed to estimate the
load share and distribution of worm gear drives, and to calculate the
instantaneous tooth meshing stiffness. In the approach, the worm gear
drive was modelled as a series of spur gear slices, and each slice was
analyzed separately using the well-established formulae of spur gear
loading and stresses. By combining the results obtained for all slices,
the entire envolute worm gear set loading and stressing was obtained. The geometric modelling method presented allows tooth elastic
deformation and tooth root stresses of worm gear drives under
different load conditions to be investigated. Based on the slicing
method introduced in this study, the instantaneous meshing stiffness
and load share are obtained. In comparison with existing methods,
this approach has both good analysis accuracy and less computing
time.
Abstract: The moisture content of densified biomass is a
limiting parameter influencing the quality of this solid biofuel. It
influences its calorific value, density, mechanical strength and
dimensional stability as well as affecting its production process. This
paper deals with experimental research into the effect of moisture
content of the densified material on the final quality of biofuel in the
form of logs (briquettes or pellets). Experiments based on the singleaxis
densification of the spruce sawdust were carried out with a
hydraulic piston press (piston and die), where the densified logs were
produced at room temperature. The effect of moisture content on the
qualitative properties of the logs, including density, change of
moisture, expansion and physical changes, and compressive and
impact resistance were studied. The results show the moisture ranges
required for producing good-quality logs. The experiments were
evaluated and the moisture content of the tested material was
optimized to achieve the optimum value for the best quality of the
solid biofuel. The dense logs also have high-energy content per unit
volume. The research results could be used to develop and optimize
industrial technologies and machinery for biomass densification to
achieve high quality solid biofuel.
Abstract: Group decision making with multiple attribute has
attracted intensive concern in the decision analysis area. This paper
assumes that the contributions of all the decision makers (DMs) are not
equal to the decision process based on different knowledge and
experience in group setting. The aim of this paper is to develop a novel
approach to determine weights of DMs in the group decision making
problems. In this paper, the weights of DMs are determined in the
group decision environment via angle cosine and projection method.
First of all, the average decision of all individual decisions is defined
as the ideal decision. After that, we define the weight of each decision
maker (DM) by aggregating the angle cosine and projection between
individual decision and ideal decision with associated direction
indicator μ. By using the weights of DMs, all individual decisions are
aggregated into a collective decision. Further, the preference order of
alternatives is ranked in accordance with the overall row value of
collective decision. Finally, an example in a chemical company is
provided to illustrate the developed approach.
Abstract: In VLSI, testing plays an important role. Major
problem in testing are test data volume and test power. The important
solution to reduce test data volume and test time is test data
compression. The Proposed technique combines the bit maskdictionary
and 2n pattern run length-coding method and provides a
substantial improvement in the compression efficiency without
introducing any additional decompression penalty. This method has
been implemented using Mat lab and HDL Language to reduce test
data volume and memory requirements. This method is applied on
various benchmark test sets and compared the results with other
existing methods. The proposed technique can achieve a compression
ratio up to 86%.
Abstract: One of the most important challenging factors in
medical images is nominated as noise. Image denoising refers to the
improvement of a digital medical image that has been infected by
Additive White Gaussian Noise (AWGN). The digital medical image
or video can be affected by different types of noises. They are
impulse noise, Poisson noise and AWGN. Computed tomography
(CT) images are subjects to low quality due to the noise. Quality of
CT images is dependent on absorbed dose to patients directly in such
a way that increase in absorbed radiation, consequently absorbed
dose to patients (ADP), enhances the CT images quality. In this
manner, noise reduction techniques on purpose of images quality
enhancement exposing no excess radiation to patients is one the
challenging problems for CT images processing. In this work, noise
reduction in CT images was performed using two different
directional 2 dimensional (2D) transformations; i.e., Curvelet and
Contourlet and Discrete Wavelet Transform (DWT) thresholding
methods of BayesShrink and AdaptShrink, compared to each other
and we proposed a new threshold in wavelet domain for not only
noise reduction but also edge retaining, consequently the proposed
method retains the modified coefficients significantly that result good
visual quality. Data evaluations were accomplished by using two
criterions; namely, peak signal to noise ratio (PSNR) and Structure
similarity (Ssim).
Abstract: A sliding door system is used in commercial vehicles
and passenger cars to allow a larger unobstructed access to the
interior for loading and unloading. The movement of a sliding door
on vehicle body is ensured by mechanisms and tracks having special
cross-section which is manufactured by roll forming and stretch
bending process. There are three tracks and three mechanisms which
are called upper, central and lower on a sliding door system. There
are static requirements as strength on different directions, rigidity for
mechanisms, door drop off, door sag; dynamic requirements as high
energy slam opening-closing and durability requirement to validate
these products. In addition, there is a kinematic requirement to find
out force values from door handle during manual operating. In this
study, finite element analysis and physical test results which are
realized for sliding door systems will be shared comparatively.
Abstract: In Automotive Industry, sliding door systems that are
also used as body closures are safety members. Extreme product tests
are realized to prevent failures in design process, but these tests
realized experimentally result in high costs. Finite element analysis is
an effective tool used for design process. These analyses are used
before production of prototype for validation of design according to
customer requirement. In result of this, substantial amount of time
and cost is saved. Finite element model is created for geometries that are designed in
3D CAD programs. Different element types as bar, shell and solid,
can be used for creating mesh model. Cheaper model can be created
by selection of element type, but combination of element type that
was used in model, number and geometry of element and degrees of
freedom affects the analysis result. Sliding door system is a good
example which used these methods for this study. Structural analysis
was realized for sliding door mechanism by using FE models. As
well, physical tests that have same boundary conditions with FE
models were realized. Comparison study for these element types,
were done regarding test and analyses results then optimum
combination was achieved.
Abstract: E-retailing is the sale of goods online that takes place
over the Internet. The Internet has shrunk the entire World. World eretailing
is growing at an exponential rate in the Americas, Europe
and Asia. However, e-retailing costs require expensive investment,
such as hardware, software, and security systems. Cloud computing
technology is internet-based computing for the management and
delivery of applications and services. Cloud-based e-retailing
application models allow enterprises to lower their costs with their
effective implementation of e-retailing activities. In this paper, we
describe the concept of cloud computing and present the architecture
of cloud computing, combining the features of e-retailing. In
addition, we propose a strategy for implementing cloud computing
with e-retailing. Finally, we explain the benefits from the
architecture.
Abstract: This research will give the introductory ideas for
cultural adaption of B2C E-Service design in Germany. By the
intense competition of E-Service development, many companies have
realized the importance of understanding the emotional and cultural
characteristics of their customers. Ignoring customers’ needs and
requirements throughout the E-Service design can lead to faults,
mistakes, and gaps. The term of E-Service usability now is changed
not only to develop high quality E-Services, but also to be extended
to include customer satisfaction and provide for them to feel local.