Abstract: Aluminum alloy sheets have several advantages such
as the lightweight, high-specific strength and recycling efficiency.
Therefore, aluminum alloy sheets in sheet forming have been used in various areas as automotive components and so forth. During the
process of sheet forming, wrinkling which is caused by compression stress might occur and the formability of sheets was affected by
occurrence of wrinkling. A few studies of uniaxial compressive test by
using square tubes, pipes and sheets were carried out to clarify the each wrinkling behavior. However, on uniaxial compressive test,
deformation behavior of the sheets hasn-t be cleared. Then, it is necessary to clarify the relationship between the buckling behavior
and the forming conditions. In this study, the effect of dimension of the sheet in the buckling behavior on compression test of aluminum alloy sheet was cleared by experiment and FEA. As the results, the buckling
deformation was classified by three modes in terms of the distribution of equivalent plastic strain.
Abstract: The integral form of equations of motion of composite
beams subjected to varying time loads are discretized using a
developed finite element model. The model consists of a straight five
node twenty-two degrees of freedom beam element. The stability
analysis of the beams is studied by solving the matrix form
characteristic equations of the system. The principle of virtual work
and the first order shear deformation theory are employed to analyze
the beams with large deformation and small strains. The regions of
dynamic instability of the beam are determined by solving the
obtained Mathieu form of differential equations. The effects of nonconservative
loads, shear stiffness, and damping parameters on
stability and response of the beams are examined. Several numerical
calculations are presented to compare the results with data reported
by other researchers.
Abstract: This experiment was conducted in attempt of
improving hydrodynamic efficiency of the propulsion mechanism by
installing a spring to the wing so that the opening angle of the wing in
one stroke can be changed automatically, compared to the existing
method of fixed maximum opening angle in Weis-Fogh type ship
propulsion mechanism. Average thrust coefficient was almost fixed
with all velocity ratio with the prototype, but with the spring type,
thrust coefficient increased sharply as velocity ratio increased.
Average propulsive efficiency was larger with bigger opening angle in
the prototype, but in the spring type, the one with smaller spring
coefficient had larger value. In the range over 1.0 in velocity ratio
where big thrust can be generated, spring type had more than twice of
propulsive efficiency increase compared to the prototype.
Abstract: This paper presents the theoretical investigation of a
slotted patch antenna. The main objective of proposed work is to
obtain a large bandwidth antenna with reduced size. The antenna has
a compact size of 21.1mm x 20.25mm x 8.5mm. Two designs with
minor variation are studied which provide wide impedance
bandwidths of 24.056% and 25.63% respectively with the use of
parasitic elements when excited by a probe feed. The advantages of
this configuration are its compact size and the wide range of
frequencies covered. A parametric study is also conducted to
investigate the characteristics of the antenna under different
conditions. The measured return loss and radiation pattern indicate
the suitability of this design for WLAN applications, namely, Wi-
Max, 802.11a/b/g and ISM bands.
Abstract: This study experimentally and numerically investigates
motor cooling performance. The motor consists of a centrifugal fan,
two axial fans, a shaft, a stator, a rotor and a heat exchanger with 637
cooling tubes. The pressure rise-flow rate (P-Q) performance curves of
the cooling fans at 1800 rpm are tested using a test apparatus
complying with the Chinese National Standard (CNS) 2726.
Compared with the experimental measurements, the numerical
analysis results show that the P-Q performance curves of the axial fan
and centrifugal fan can be estimated within about 2% and 6%,
respectively. By using the simplified model, setting up the heat
exchanger and stator as porous media, the flow field in the motor is
calculated. By using the results of the flow field near the rotor and
stator, and subjecting the heat generation rate as a boundary condition,
the temperature distributions of the stator and rotor are also calculated.
The simulation results show that the calculated temperature of the
stator winding near the axial fans is lower by about 5% than the
measured value, and the calculated temperature of the stator core
located at the center of the stator is about 1% higher than the measured
value. Besides, discussion is made to improve the motor cooling
performance.
Abstract: Hazardous Material transportation by road is coupled
with inherent risk of accidents causing loss of lives, grievous injuries,
property losses and environmental damages. The most common type
of hazmat road accident happens to be the releases (78%) of
hazardous substances, followed by fires (28%), explosions (14%) and
vapour/ gas clouds (6 %.).
The paper is discussing initially the probable 'Impact Zones'
likely to be caused by one flammable (LPG) and one toxic (ethylene
oxide) chemicals being transported through a sizable segment of a
State Highway connecting three notified Industrial zones in Surat
district in Western India housing 26 MAH industrial units. Three
'hotspots' were identified along the highway segment depending on
the particular chemical traffic and the population distribution within
500 meters on either sides. The thermal radiation and explosion
overpressure have been calculated for LPG / Ethylene Oxide BLEVE
scenarios along with toxic release scenario for ethylene oxide.
Besides, the dispersion calculations for ethylene oxide toxic release
have been made for each 'hotspot' location and the impact zones
have been mapped for the LOC concentrations. Subsequently, the
maximum Initial Isolation and the protective zones were calculated
based on ERPG-3 and ERPG-2 values of ethylene oxide respectively
which are estimated taking the worst case scenario under worst
weather conditions. The data analysis will be helpful to the local
administration in capacity building with respect to rescue /
evacuation and medical preparedness and quantitative inputs to
augment the District Offsite Emergency Plan document.
Abstract: Warranty is a powerful marketing tool for the
manufacturer and a good protection for both the manufacturer and the
customer. However, warranty always involves additional costs to the
manufacturer, which depend on product reliability characteristics and
warranty parameters. This paper presents an approach to optimisation
of warranty parameters for known product failure distribution to
reduce the warranty costs to the manufacturer while retaining the
promotional function of the warranty. Combination free replacement
and pro-rata warranty policy is chosen as a model and the length of
free replacement period and pro-rata policy period are varied, as well
as the coefficients that define the pro-rata cost function. Multiparametric
warranty optimisation is done by using genetic algorithm.
Obtained results are guideline for the manufacturer to choose the
warranty policy that minimises the costs and maximises the profit.
Abstract: In this paper an algorithm is used to detect the color defects of ceramic tiles. First the image of a normal tile is clustered using GCMA; Genetic C-means Clustering Algorithm; those results in best cluster centers. C-means is a common clustering algorithm which optimizes an objective function, based on a measure between data points and the cluster centers in the data space. Here the objective function describes the mean square error. After finding the best centers, each pixel of the image is assigned to the cluster with closest cluster center. Then, the maximum errors of clusters are computed. For each cluster, max error is the maximum distance between its center and all the pixels which belong to it. After computing errors all the pixels of defected tile image are clustered based on the centers obtained from normal tile image in previous stage. Pixels which their distance from their cluster center is more than the maximum error of that cluster are considered as defected pixels.
Abstract: Antimicrobial resistant is becoming a major factor in
virtually all hospital acquired infection may soon untreatable is a
serious public health problem. These concerns have led to major
research effort to discover alternative strategies for the treatment of
bacterial infection. Nanobiotehnology is an upcoming and fast
developing field with potential application for human welfare. An
important area of nanotechnology for development of reliable and
environmental friendly process for synthesis of nanoscale particles
through biological systems In the present studies are reported on the
use of fungal strain Aspergillus species for the extracellular synthesis
of bionanoparticles from 1 mM silver nitrate (AgNO3) solution. The
report would be focused on the synthesis of metallic bionanoparticles
of silver using a reduction of aqueous Ag+ ion with the
culture supernatants of Microorganisms. The bio-reduction of the
Ag+ ions in the solution would be monitored in the aqueous
component and the spectrum of the solution would measure through
UV-visible spectrophotometer The bionanoscale particles were
further characterized by Atomic Force Microscopy (AFM), Fourier
Transform Infrared Spectroscopy (FTIR) and Thin layer
chromatography. The synthesized bionanoscale particle showed a
maximum absorption at 385 nm in the visible region. Atomic Force
Microscopy investigation of silver bionanoparticles identified that
they ranged in the size of 250 nm - 680 nm; the work analyzed the
antimicrobial efficacy of the silver bionanoparticles against various
multi drug resistant clinical isolates. The present Study would be
emphasizing on the applicability to synthesize the metallic
nanostructures and to understand the biochemical and molecular
mechanism of nanoparticles formation by the cell filtrate in order to
achieve better control over size and polydispersity of the
nanoparticles. This would help to develop nanomedicine against
various multi drug resistant human pathogens.
Abstract: It is necessary to evaluate the bridges conditions and
strengthen bridges or parts of them. The reinforcement necessary due
to some reasons can be summarized as: First, a changing in use of
bridge could produce internal forces in a part of structural which
exceed the existing cross-sectional capacity. Second, bridges may
also need reinforcement because damage due to external factors
which reduced the cross-sectional resistance to external loads. One of
other factors could listed here its misdesign in some details, like
safety of bridge or part of its.This article identify the design demands
of Qing Shan bridge located in is in Heilongjiang Province He gang -
Nen Jiang Road 303 provincial highway, Wudalianchi area, China, is
an important bridge in the urban areas. The investigation program
was include the observation and evaluate the damage in T- section
concrete beams , prestressed concrete box girder bridges section in
additional evaluate the whole state of bridge includes the pier ,
abutments , bridge decks, wings , bearing and capping beam, joints,
........etc. The test results show that the bridges in general structural
condition are good. T beam span No 10 were observed, crack
extended upward along the ribbed T beam, and continue to the T
beam flange. Crack width varying between 0.1mm to 0.4mm, the
maximum about 0.4mm. The bridge needs to be improved flexural
bending strength especially at for T beam section.
Abstract: The problem of estimating time-varying regression is
inevitably concerned with the necessity to choose the appropriate
level of model volatility - ranging from the full stationarity of instant
regression models to their absolute independence of each other. In the
stationary case the number of regression coefficients to be estimated
equals that of regressors, whereas the absence of any smoothness
assumptions augments the dimension of the unknown vector by the
factor of the time-series length. The Akaike Information Criterion
is a commonly adopted means of adjusting a model to the given
data set within a succession of nested parametric model classes,
but its crucial restriction is that the classes are rigidly defined by
the growing integer-valued dimension of the unknown vector. To
make the Kullback information maximization principle underlying the
classical AIC applicable to the problem of time-varying regression
estimation, we extend it onto a wider class of data models in which
the dimension of the parameter is fixed, but the freedom of its values
is softly constrained by a family of continuously nested a priori
probability distributions.
Abstract: To evaluate genetic variation of wheat (Triticum
aestivum) affected by heat and drought stress on eight Australian
wheat genotypes that are parents of Doubled Haploid (HD) mapping
populations at the vegetative stage, the water stress experiment was
conducted at 65% field capacity in growth room. Heat stress
experiment was conducted in the research field under irrigation over
summer. Result show that water stress decreased dry shoot weight
and RWC but increased osmolarity and means of Fv/Fm values in all
varieties except for Krichauff. Krichauff and Kukri had the
maximum RWC under drought stress. Trident variety was shown
maximum WUE, osmolarity (610 mM/Kg), dry mater, quantum yield
and Fv/Fm 0.815 under water stress condition. However, the
recovery of quantum yield was apparent between 4 to 7 days after
stress in all varieties. Nevertheless, increase in water stress after that
lead to strong decrease in quantum yield. There was a genetic
variation for leaf pigments content among varieties under heat stress.
Heat stress decreased significantly the total chlorophyll content that
measured by SPAD. Krichauff had maximum value of Anthocyanin
content (2.978 A/g FW), chlorophyll a+b (2.001 mg/g FW) and
chlorophyll a (1.502 mg/g FW). Maximum value of chlorophyll b
(0.515 mg/g FW) and Carotenoids (0.234 mg/g FW) content
belonged to Kukri. The quantum yield of all varieties decreased
significantly, when the weather temperature increased from 28 ÔùªC to
36 ÔùªC during the 6 days. However, the recovery of quantum yield
was apparent after 8th day in all varieties. The maximum decrease
and recovery in quantum yield was observed in Krichauff. Drought
and heat tolerant and moderately tolerant wheat genotypes were
included Trident, Krichauff, Kukri and RAC875. Molineux, Berkut
and Excalibur were clustered into most sensitive and moderately
sensitive genotypes. Finally, the results show that there was a
significantly genetic variation among the eight varieties that were
studied under heat and water stress.
Abstract: In this paper the design of maximally flat linear phase
finite impulse response (FIR) filters is considered. The problem is
handled with totally two different approaches. The first one is
completely deterministic numerical approach where the problem is
formulated as a Linear Complementarity Problem (LCP). The other
one is based on a combination of Markov Random Fields (MRF's)
approach with messy genetic algorithm (MGA). Markov Random
Fields (MRFs) are a class of probabilistic models that have been
applied for many years to the analysis of visual patterns or textures.
Our objective is to establish MRFs as an interesting approach to
modeling messy genetic algorithms. We establish a theoretical result
that every genetic algorithm problem can be characterized in terms of
a MRF model. This allows us to construct an explicit probabilistic
model of the MGA fitness function and introduce the Ising MGA.
Experimentations done with Ising MGA are less costly than those
done with standard MGA since much less computations are involved.
The least computations of all is for the LCP. Results of the LCP,
random search, random seeded search, MGA, and Ising MGA are
discussed.
Abstract: In this study, the numerical solution of unsteady flow
between two concentric rotating spheres with suction and blowing at
their boundaries is presented. The spheres are rotating about a
common axis of rotation while their angular velocities are constant.
The Navier-Stokes equations are solved by employing the finite
difference method and implicit scheme. The resulting flow patterns
are presented for various values of the flow parameters including
rotational Reynolds number Re , and a blowing/suction Reynolds
number Rew . Viscous torques at the inner and the outer spheres are
calculated, too. It is seen that increasing the amount of suction and
blowing decrease the size of eddies generated in the annulus.
Abstract: In this paper we study a system composed by carbon
nanotube (CNT) and bundle of carbon nanotube (BuCNT) interacting
with a specific fatty acid as molecular probe. Full system is
represented by open nanotube (or nanotubes) and the linoleic acid
(LA) relaxing due the interaction with CNT and BuCNT. The LA has
in his form an asymmetric shape with COOH termination provoking
a close BuCNT interaction mainly by van der Waals force field. The
simulations were performed by classical molecular dynamics with
standard parameterizations.
Our results show that these BuCNT and CNT are dynamically
stable and it shows a preferential interaction position with LA
resulting in three features: (i) when the LA is interacting with CNT
and BuCNT (including both termination, CH2 or COOH), the LA is
repelled; (ii) when the LA terminated with CH2 is closer to open
extremity of BuCNT, the LA is also repelled by the interaction
between them; and (iii) when the LA terminated with COOH is
closer to open extremity of BuCNT, the LA is encapsulated by the
BuCNT. These simulations are part of a more extensive work on
searching efficient selective molecular devices and could be useful to
reach this goal.
Abstract: The fluid mechanics principle is used extensively in
designing axial flow fans and their associated equipment. This paper presents a computational fluid dynamics (CFD) modeling of air flow
distribution from a radiator axial flow fan used in an acid pump truck Tier4 (APT T4) Repower. This axial flow fan augments the transfer
of heat from the engine mounted on the APT T4.
CFD analysis was performed for an area weighted average static pressure difference at the inlet and outlet of the fan. Pressure contours, velocity vectors, and path lines were plotted for detailing
the flow characteristics for different orientations of the fan blade. The results were then compared and verified against known theoretical observations and actual experimental data. This study
shows that a CFD simulation can be very useful for predicting and understanding the flow distribution from a radiator fan for further
research work.
Abstract: In this paper, cloud resource broker using goalbased
request in medical application is proposed. To handle recent
huge production of digital images and data in medical informatics
application, the cloud resource broker could be used by medical
practitioner for proper process in discovering and selecting correct
information and application. This paper summarizes several
reviewed articles to relate medical informatics application with
current broker technology and presents a research work in applying
goal-based request in cloud resource broker to optimize the use of
resources in cloud environment. The objective of proposing a new
kind of resource broker is to enhance the current resource
scheduling, discovery, and selection procedures. We believed that
it could help to maximize resources allocation in medical
informatics application.
Abstract: Natural resources management including water resources requires reliable estimations of time variant environmental parameters. Small improvements in the estimation of environmental parameters would result in grate effects on managing decisions. Noise reduction using wavelet techniques is an effective approach for preprocessing of practical data sets. Predictability enhancement of the river flow time series are assessed using fractal approaches before and after applying wavelet based preprocessing. Time series correlation and persistency, the minimum sufficient length for training the predicting model and the maximum valid length of predictions were also investigated through a fractal assessment.
Abstract: Web usage mining algorithms have been widely
utilized for modeling user web navigation behavior. In this study we
advance a model for mining of user-s navigation pattern. The model
makes user model based on expectation-maximization (EM)
algorithm.An EM algorithm is used in statistics for finding maximum
likelihood estimates of parameters in probabilistic models, where the
model depends on unobserved latent variables. The experimental
results represent that by decreasing the number of clusters, the log
likelihood converges toward lower values and probability of the
largest cluster will be decreased while the number of the clusters
increases in each treatment.
Abstract: The objective of this paper is to analyze the
performance of a double-sided axial flux permanent magnet
brushless DC (AFPM BLDC) motor with two-phase winding.
To study the motor operation, a mathematical dynamic model
has been proposed for motor, which became the basis for
simulations that were performed using MATLAB/SIMULINK
software package. The results of simulations were presented
in form of the waveforms of selected quantities and the
electromechanical characteristics performed by the motor. The
calculation results show that the two-phase motor version
develops smooth torque and reaches high efficiency. The twophase
motor can be applied where more smooth torque is
required. Finally a study on the influence of switching angle
on motor performance shows that when advance switching
technique is used, the motor operates with the highest
efficiency.