Abstract: Recently, there is a lot of interest in the field of under
water optical wireless communication for short range because of
its high bandwidth. But in most of the previous works line of
sight propagation or single scattering of photons only considered.
In practical case this is not applicable because of beam blockage in
underwater and multiple scattering also occurred during the photons
propagation through water. In this paper we consider a non-line
of sight underwater wireless optical communication system with
multiple scattering and examine the performance of the system using
monte carlo simulation. The distribution scattering angle of photons
are modeled by Henyey-Greenstein method. The average bit error
rate is calculated using on-off keying modulation for different water
types.
Abstract: Egg yolk oil is a natural source of bioactive
compounds such as unsaturated fatty acids, oil soluble vitamins,
pigments and others. Bioactive compound content in egg yolk oil
depends from its content in eggs, from which oil was extracted. Many
studies show that bioactive compound content in egg is correlated to
the content of these compounds in hen feed, but there is also an
opinion that hen housing systems also have influence on egg
chemical content. The aim of this study was to determine which
factor, laying hen housing system or hen diet, has a primary influence
on bioactive compound content in egg yolk oil. The egg yolk oil was
extracted from eggs obtained from 4 different hen housing systems:
cage, barn and two groups of free range. All hens were fed with
commercially produced compound feed except one group of free
range hens which get free diet – pastured hens. Extracted egg yolk
oils were analyzed for fatty acids, oil soluble vitamins and β-carotene
content. α-tocopherol, ergocalcipherol and polyunsaturated fatty acid
content in egg yolk oil was higher from eggs obtained from all
housing systems where hens were fed with commercial compound
feed. β-carotene and retinol content in egg yolk oils from free range
free diet eggs was significantly (p>0.05) higher that from other eggs
because hens have access to green forage. Hen physical activity in
free range housing systems decreases content of some bioactive
compound in egg yolk oil.
Abstract: A chromium-loaded ash originating from incineration of tannery sludge under anoxic conditions was mixed with low grade soda-lime glass powder coming from commercial glass bottles. The relative weight proportions of ash over glass powder tested were 30/70, 40/60 and 50/50. The solid mixtures, formed in green state compacts, were sintered at the temperature range of 800o C up to 1200o C. The resulting products were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive X-ray spectrometry (EDXS) and micro-indentation. The above methods were employed to characterize the various phases, microstructure and hardness of the produced materials. Thermal treatment at 800o C and 1000o C produced opaque ceramic products composed of a variety of chromium-containing and chromium-free crystalline phases. Thermal treatment at 1200o C gave rise to composite products, where only chromium-containing crystalline phases were detected. Hardness results suggest that specific products are serious candidates for structural applications.
Abstract: The design philosophy of building structure has been
changing time to time. The reason for this is because of an increase of
human inertest, an improved building materials and technology that
will impact how we live, to speed up construction period and natural
effect which includes earthquake disasters and environmental effect.
One technique which takes in to account the above case is using a
prefabricable structural system. In which each and every structural
element is designed and prefabricated and assembled on a site so that
the construction speed is increased and the environmental impact is
also enhanced. This system has an immense advantage such as: reduce
construction cost, reusable, recyclable, speed up construction period
and less environmental effect. In this study, it is tried to present some
of the developed and evaluated structural elements of building
structures.
Abstract: The biodegradable family of polymers
polyhydroxyalkanoates is an interesting substitute for convectional
fossil-based plastics. However, the manufacturing and environmental
impacts associated with their production via intracellular bacterial
fermentation are strongly dependent on the raw material used and on
energy consumption during the extraction process, limiting their
potential for commercialization. Industrial wastewater is studied in
this paper as a promising alternative feedstock for waste valorization.
Based on results from laboratory and pilot-scale experiments, a
conceptual process design, techno-economic analysis and life cycle
assessment are developed for the large-scale production of the most
common type of polyhydroxyalkanoate, polyhydroxbutyrate.
Intracellular polyhydroxybutyrate is obtained via fermentation of
microbial community present in industrial wastewater and the
downstream processing is based on chemical digestion with
surfactant and hypochlorite. The economic potential and
environmental performance results help identifying bottlenecks and
best opportunities to scale-up the process prior to industrial
implementation. The outcome of this research indicates that the
fermentation of wastewater towards PHB presents advantages
compared to traditional PHAs production from sugars because the
null environmental burdens and financial costs of the raw material in
the bioplastic production process. Nevertheless, process optimization
is still required to compete with the petrochemicals counterparts.
Abstract: Freshly laid eggs from green turtles, Chelonia mydas,
were randomly collected from Ras Al-Hadd Reserve, Oman.
Eggshells taken from eggs and sand collected from the body chamber
were analyzed for eight heavy metals (Al, Br, Cd, Co, Cu, Fe, S, and
Zn) using inductively coupled plasma mass spectrometry (ICP).
Heavy metal concentrations varied significantly (P
Abstract: The introduction of degradable plastic materials into
agricultural sectors has represented a promising alternative to
promote green agriculture and environmental friendly of modern
farming practices. Major challenges of developing degradable
agricultural films are to identify the most feasible types of
degradation mechanisms, composition of degradable polymers and
related processing techniques. The incorrect choice of degradable
mechanisms to be applied during the degradation process will cause
premature losses of mechanical performance and strength. In order to
achieve controlled process of agricultural film degradation, the
compositions of degradable agricultural film also important in order
to stimulate degradation reaction at required interval of time and to
achieve sustainability of the modern agricultural practices. A set of
photodegradable polyethylene based agricultural film was developed
and produced, following the selective optimization of processing
parameters of the agricultural film manufacturing system. Example of
agricultural films application for oil palm seedlings cultivation is
presented.
Abstract: Parabolic solar trough systems have seen limited
deployments in cold northern climates as they are more suitable for
electricity production in southern latitudes. A numerical dynamic
model is developed to simulate troughs installed in cold climates and
validated using a parabolic solar trough facility in Winnipeg. The
model is developed in Simulink and will be utilized to simulate a trigeneration
system for heating, cooling and electricity generation in
remote northern communities. The main objective of this simulation
is to obtain operational data of solar troughs in cold climates and use
the model to determine ways to improve the economics and address
cold weather issues.
In this paper the validated Simulink model is applied to simulate a
solar assisted absorption cooling system along with electricity
generation using Organic Rankine Cycle (ORC) and thermal storage.
A control strategy is employed to distribute the heated oil from solar
collectors among the above three systems considering the
temperature requirements. This modelling provides dynamic
performance results using measured meteorological data recorded
every minute at the solar facility location. The purpose of this
modeling approach is to accurately predict system performance at
each time step considering the solar radiation fluctuations due to
passing clouds. Optimization of the controller in cold temperatures is
another goal of the simulation to for example minimize heat losses in
winter when energy demand is high and solar resources are low.
The solar absorption cooling is modeled to use the generated heat
from the solar trough system and provide cooling in summer for a
greenhouse which is located next to the solar field.
The results of the simulation are presented for a summer day in
Winnipeg which includes comparison of performance parameters of
the absorption cooling and ORC systems at different heat transfer
fluid (HTF) temperatures.
Abstract: Recently, the green architecture becomes a
significant way to a sustainable future. Green building designs
involve finding the balance between comfortable homebuilding and
sustainable environment. Moreover, the utilization of the new
technologies such as artificial intelligence techniques are used to
complement current practices in creating greener structures to keep
the built environment more sustainable. The most common objectives
in green buildings should be designed to minimize the overall impact
of the built environment that effect on ecosystems in general and in
particularly human health and natural environment. This will lead to
protecting occupant health, improving employee productivity,
reducing pollution and sustaining the environmental. In green
building design, multiple parameters which may be interrelated,
contradicting, vague and of qualitative/quantitative nature are
broaden to use. This paper presents a comprehensive critical state- ofart-
review of current practices based on fuzzy and its combination
techniques. Also, presented how green architecture/building can be
improved using the technologies that been used for analysis to seek
optimal green solutions strategies and models to assist in making the
best possible decision out of different alternatives.
Abstract: Peace education supports a holistic appreciation for
the value of life and the interdependence of all living systems. Peace
education aims to build a culture of peace. One way of building a
culture of peace is through environmental stewardship. This study
sought to find out the environmental stewardship practices in selected
Higher Education Institutions (HEIs) in the Philippines and how
these environmental stewardship practices lead to building a culture
of peace. The findings revealed that there is still room for
improvement in implementing environmental stewardship in schools
through academic service learning. In addition, the following
manifestations are implemented very satisfactorily in schools: 1)
waste reduction, reuse, and recycling, 2) community service, and 3)
clean and green surroundings. Administrators of schools in the study
lead their staff and students in implementing environmental
stewardship. It could be concluded that those involved in
environmental stewardship display an acceptable culture of peace,
particularly solidarity, respect for persons, and inner peace.
Abstract: Catalytic combustion of methane is imperative due to
stability of methane at low temperature. Methane (CH4), therefore,
remains unconverted in vehicle exhausts thereby causing greenhouse
gas GHG emission problem. In this study, heterogeneous catalysts of
palladium with bio-char (2 wt% Pd/Bc) and Al2O3 (2wt% Pd/ Al2O3)
supports were prepared by incipient wetness impregnation and then
subsequently tested for catalytic combustion of CH4. Support-porous
heterogeneous catalytic combustion (HCC) material were selected
based on factors such as surface area, porosity, thermal stability,
thermal conductivity, reactivity with reactants or products, chemical
stability, catalytic activity, and catalyst life. Sustainable and
renewable support-material of bio-mass char derived from palm shell
waste material was compared with those from the conventional
support-porous materials. Kinetic rate of reaction was determined for
combustion of methane on Palladium (Pd) based catalyst with Al2O3
support and bio-char (Bc). Material characterization was done using
TGA, SEM, and BET surface area. The performance test was
accomplished using tubular quartz reactor with gas mixture ratio of
3% methane and 97% air. The methane porous-HCC conversion was
carried out using online gas analyzer connected to the reactor that
performed porous-HCC. BET surface area for prepared 2 wt% Pd/Bc
is smaller than prepared 2wt% Pd/ Al2O3 due to its low porosity
between particles. The order of catalyst activity based on kinetic rate
on reaction of catalysts in low temperature was 2wt%
Pd/Bc>calcined 2wt% Pd/ Al2O3> 2wt% Pd/ Al2O3>calcined 2wt%
Pd/Bc. Hence agro waste material can successfully be utilized as an
inexpensive catalyst support material for enhanced CH4 catalytic
combustion.
Abstract: Most people today are aware that global climate
change is not just a scientific theory but also a fact with worldwide
consequences. Global climate change is due to rapid urbanization,
industrialization, high population growth and current vulnerability of
the climatic condition. Water is becoming scarce as a result of global
climate change. To mitigate the problem arising due to global climate
change and its drought effect, harvesting rainwater from green roofs,
an environmentally-friendly and versatile technology, is becoming
one of the best assessment criteria and gaining attention in Malaysia.
This paper addresses the sustainability of green roofs and examines
the quality of water harvested from green roofs in comparison to
rainwater. The factors that affect the quality of such water, taking
into account, for example, roofing materials, climatic conditions, the
frequency of rainfall frequency and the first flush. A green roof was
installed on the Humid Tropic Centre (HTC) is a place of the study
on monitoring program for urban Stormwater Management Manual
for Malaysia (MSMA), Eco-Hydrological Project in Kuala Lumpur,
and the rainwater was harvested and evaluated on the basis of four
parameters i.e., conductivity, dissolved oxygen (DO), pH and
temperature. These parameters were found to fall between Class I and
Class III of the Interim National Water Quality Standards (INWQS)
and the Water Quality Index (WQI). Some preliminary treatment
such as disinfection and filtration could likely to improve the value of
these parameters to class I. This review paper clearly indicates that
there is a need for more research to address other microbiological and
chemical quality parameters to ensure that the harvested water is
suitable for use potable water for domestic purposes. The change in
all physical, chemical and microbiological parameters with respect to
storage time will be a major focus of future studies in this field.
Abstract: Solid waste management in steel industry is broadly
classified in “4 Rs” i.e. reduce, reuse, recycle and restore the
materials. Reuse and recycling the entire solid waste generated in the
process of steel making is a viable solution in targeting a clean, green
and zero waste technology leading to sustainable development of the
steel industry. Solid waste management has gained importance in
steel industry in view of its uncertainty, volatility and speculation due
to world competitive standards, rising input costs, scarcity of raw
materials and solid waste generated like in other sectors. The
challenges that the steel Industry faces today are the requirement of a
sustainable development by meeting the needs of our present
generation without compromising the ability of future generations.
Technologies are developed not only for gainful utilization of solid
wastes in manufacture of conventional products but also for
conversion of same in to completely new products.
Abstract: The building sector is responsible, in many
industrialized countries, for about 40% of the total energy
requirements, so it seems necessary to devote some efforts in this
area in order to achieve a significant reduction of energy
consumption and of greenhouse gases emissions.
The paper presents a study aiming at providing a design
methodology able to identify the best configuration of the system
building/plant, from a technical, economic and environmentally point
of view.
Normally, the classical approach involves a building's energy
loads analysis under steady state conditions, and subsequent selection
of measures aimed at improving the energy performance, based on
previous experience made by architects and engineers in the design
team. Instead, the proposed approach uses a sequence of two wellknown
scientifically validated calculation methods (TRNSYS and
RETScreen), that allow quite a detailed feasibility analysis.
To assess the validity of the calculation model, an existing,
historical building in Central Italy, that will be the object of
restoration and preservative redevelopment, was selected as a casestudy.
The building is made of a basement and three floors, with a
total floor area of about 3,000 square meters.
The first step has been the determination of the heating and
cooling energy loads of the building in a dynamic regime by means,
which allows simulating the real energy needs of the building in
function of its use. Traditional methodologies, based as they are on
steady-state conditions, cannot faithfully reproduce the effects of
varying climatic conditions and of inertial properties of the structure.
With this model is possible to obtain quite accurate and reliable
results that allow identifying effective combinations building-HVAC
system.
The second step has consisted of using output data obtained as
input to the calculation model, which enables to compare different
system configurations from the energy, environmental and financial
point of view, with an analysis of investment, and operation and
maintenance costs, so allowing determining the economic benefit of
possible interventions.
The classical methodology often leads to the choice of
conventional plant systems, while our calculation model provides a
financial-economic assessment for innovative energy systems and
low environmental impact.
Computational analysis can help in the design phase, particularly
in the case of complex structures with centralized plant systems, by
comparing the data returned by the calculation model for different
design options.
Abstract: The objective of this study was to evaluate the
physical and chemical characteristics of Serra da Estrela cheese and
compare these results with those of the sensory analysis. For the
study were taken six samples of Serra da Estrela cheese produced
with 6 different ecotypes of thistle in a dairy situated in Penalva do
Castelo. The chemical properties evaluated were moisture content,
protein, fat, ash, chloride and pH; the physical properties studied
were color and texture; and finally a sensory evaluation was
undertaken. The results showed moisture varying in the range 40-
48%, protein in the range 15-20%, fat between 41-45%, ash between
3.9-5.0% and chlorides varying from 1.2 to 3.0%. The pH varied
from 4.8 to 5.4. The textural properties revealed that the crust
hardness is relatively low (maximum 7.3 N), although greater than
flesh firmness (maximum 1.7 N), and also that these cheeses are in
fact soft paste type, with measurable stickiness and intense
adhesiveness. The color analysis showed that the crust is relatively
light (L* over 50), and with a predominant yellow coloration (b*
around 20 or over) although with a slight greenish tone (a* negative).
The results of the sensory analysis did not show great variability for
most of the attributes measured, although some differences were
found in attributes such as crust thickness, crust uniformity, and
creamy flesh.
Abstract: Part and parcel of building green homes (GHs) with
favorable thermal comfort (TC) is to design and build with reduced
carbon footprint (CF) from embodied energy in the building envelope
and reduced operational CF overall. Together, the environmental
impact of GHs can be reduced significantly. Nevertheless, there is
still a need to identify the base CF value for Malaysian GHs and this
can be done by assessing existing ones which can then be compared
to conventional and vernacular houses which are built differently
with different building materials. This paper underlines the research
design and introduces the case studies. For now, the operational CF
of the case studies is beyond the scope of this study. Findings from
this research could identify the best building material and
construction technique combination to build GHs depending on the
available skills, financial constraints and the condition of the
immediate environment.
Abstract: Diminished antioxidant defense or increased
production of reactive oxygen species in the biological system can
result in oxidative stress which may lead to various
neurodegenerative diseases including Alzheimer’s disease (AD).
Microglial activation also contributes to the progression of AD by
producing several proinflammatory cytokines, nitric oxide (NO) and
prostaglandin E2 (PGE2). Oxidative stress and inflammation have
been reported to be possible pathophysiological mechanisms
underlying AD. In addition, the cholinergic hypothesis postulates that
memory impairment in patient with AD is also associated with the
deficit of cholinergic function in the brain. Although a number of
drugs have been approved for the treatment of AD, most of these
synthetic drugs have diverse side effects and yield relatively modest
benefits. Marine algae have great potential in pharmaceutical and
biomedical applications as they are valuable sources of bioactive
properties such as anticoagulation, antimicrobial, antioxidative,
anticancer and anti-inflammatory. Hence, this study aimed to provide
an overview of the properties of Malaysian seaweeds (Padina
australis, Sargassum polycystum and Caulerpa racemosa) in
inhibiting oxidative stress, neuroinflammation and cholinesterase
enzymes. These seaweeds significantly exhibited potent DPPH and
moderate superoxide anion radical scavenging ability (P
Abstract: Absorptive capacity generally facilitates the adoption
of innovation. How does this relationship change when economic
return is not the sole driver of innovation uptake? We investigate
whether absorptive capacity facilitates the adoption of green
innovation based on a survey of 79 construction companies in
Scotland. Based on the results of multiple regression analyses, we
confirm that existing knowledge utilisation (EKU), knowledge
building (KB) and external knowledge acquisition (EKA) are
significant predictors of green process GP), green administrative
(GA) and green technical innovation (GT), respectively. We discuss
the implications for theories of innovation adoption and knowledge
enhancement associated with environmentally-friendly practices.
Abstract: Composite material based on Fe3Si micro-particles
and Mn-Zn nano-ferrite was prepared using powder metallurgy
technology. The sol-gel followed by autocombustion process was
used for synthesis of Mn0.8Zn0.2Fe2O4 ferrite. 3 wt.% of mechanically
milled ferrite was mixed with Fe3Si powder alloy. Mixed micro-nano
powder system was homogenized by the Resonant Acoustic Mixing
using ResodynLabRAM Mixer. This non-invasive homogenization
technique was used to preserve spherical morphology of Fe3Si
powder particles. Uniaxial cold pressing in the closed die at pressure
600 MPa was applied to obtain a compact sample. Microwave
sintering of green compact was realized at 800°C, 20 minutes, in air.
Density of the powders and composite was measured by
Hepycnometry. Impulse excitation method was used to measure
elastic properties of sintered composite. Mechanical properties were
evaluated by measurement of transverse rupture strength (TRS) and
Vickers hardness (HV). Resistivity was measured by 4 point probe
method. Ferrite phase distribution in volume of the composite was
documented by metallographic analysis.
It has been found that nano-ferrite particle distributed among
micro- particles of Fe3Si powder alloy led to high relative density
(~93%) and suitable mechanical properties (TRS >100 MPa, HV
~1GPa, E-modulus ~140 GPa) of the composite. High electric
resistivity (R~6.7 ohm.cm) of prepared composite indicate their
potential application as soft magnetic material at medium and high
frequencies.
Abstract: Environmental impact assessment techniques have
been developed as a result of the worldwide efforts to reduce the
environmental impact of global warming. By using the quantification
method in the construction industry, it is now possible to manage the
greenhouse gas is to systematically evaluate the impact on the
environment over the entire construction process. In particular, the
proportion of greenhouse gas emissions at the production stage of
construction material occupied is high, and efforts are needed in
particular in the construction field.
In this research, intended for concrete products for the construction
materials, by using the LCA method, we compared the results of
environmental impact assessment and carbon emissions of developing
products that have been applied low-carbon technologies compared to
existing products. As a results, by introducing a raw material of
industrial waste, showed carbon reduction. Through a comparison of
the carbon emission reduction effect of low carbon technologies, it is
intended to provide academic data for the evaluation of greenhouse
gases in the construction sector and the development of low carbon
technologies of the future.