Abstract: Structural analysis of flexible pavements has been and still is currently performed using multi-layer elastic theory. However, for thinly surfaced pavements subjected to low to medium volumes of traffics, the importance of non-linear stress-strain behavior of unbound granular materials (UGM) requires the use of more sophisticated numerical models for structural design and performance of such pavements. In the present work, nonlinear unbound aggregates constitutive model is implemented within an axisymmetric finite element code developed to simulate the nonlinear behavior of pavement structures including two local aggregates of different mineralogical nature, typically used in Algerian pavements. The performance of the mechanical model is examined about its capability of representing adequately, under various conditions, the granular material non-linearity in pavement analysis. In addition, deflection data collected by Falling Weight Deflectometer (FWD) are incorporated into the analysis in order to assess the sensitivity of critical pavement design criteria and pavement design life to the constitutive model. Finally, conclusions of engineering significance are formulated.
Abstract: This paper presents the results of a Finite Element
based vibration analysis of a solar powered Unmanned Aerial
Vehicle (UAV). The purpose of this paper was to quantify the free
vibration, forced vibration response due to differing point inputs in
order to predict the relative response magnitudes and frequencies at
various wing locations of vibration induced power generators
(magnet in coil) excited by gust and/or control surface pulse-decays
used to help power the flight of the electric UAV. A Fluid Structure
Interaction (FSI) study was performed in order to ascertain pertinent
design stresses and deflections as well as aerodynamic parameters of
the UAV airfoil. The 10 ft span airfoil is modeled using Mylar as the
primary material. Results show that the free mode in bending is 4.8
Hz while the first forced bending mode is on range of 16.2 to 16.7 Hz
depending on the location of excitation. The free torsional bending
mode is 28.3 Hz, and the first forced torsional mode is range of 26.4
to 27.8 Hz, depending on the location of excitation. The FSI results
predict the coefficients of aerodynamic drag and lift of 0.0052 and
0.077, respectively, which matches hand-calculations used to validate
the Finite Element based results. FSI based maximum von Mises
stresses and deflections were found to be 0.282 MPa and 3.4 mm,
respectively. Dynamic pressures on the airfoil range from 1.04 to
1.23 kPa corresponding to velocity magnitudes in range of 22 to 66
m/s.
Abstract: In this study, failure analysis of pipe system at a micro
hydroelectric power plant is investigated. Failure occurred at the pipe
system in the powerhouse during shut down operation of the water
flow by a valve. This locking had caused a sudden shock wave, also
called “Water-hammer effect”, resulting in noise and inside pressure
increase. After visual investigation of the effect of the shock wave on
the system, a circumference crack was observed at the pipe flange
weld region. To establish the reason for crack formation, calculations
of pressure and stress values at pipe, flange and welding seams were
carried out and concluded that safety factor was high (2.2), indicating
that no faulty design existed. By further analysis, pipe system and
hydroelectric power plant was examined. After observations it is
determined that the plant did not include a ventilation nozzle (air
trap), that prevents the system of sudden pressure increase inside the
pipes which is caused by water-hammer effect. Analyses were carried
out to identify the influence of water-hammer effect on inside
pressure increase and it was concluded that, according Jowkowsky’s
equation, shut down time is effective on inside pressure increase. The
valve closing time was uncertain but by a shut down time of even one
minute, inside pressure would increase by 7.6 bar (working pressure
was 34.6 bar). Detailed investigations were also carried out on the
assembly of the pipe-flange system by considering technical
drawings. It was concluded that the pipe-flange system was not
installed according to the instructions. Two of five weld seams were
not applied and one weld was carried out faulty. This incorrect and
inadequate weld seams resulted in; insufficient connection of the pipe
to the flange constituting a strong notch effect at weld seam regions,
increase in stress values and the decrease of strength and safety
factor.
Abstract: The current tools for real time management of sewer
systems are based on two software tools: the software of weather
forecast and the software of hydraulic simulation. The use of the first
ones is an important cause of imprecision and uncertainty, the use of
the second requires temporal important steps of decision because of
their need in times of calculation. This way of proceeding fact that
the obtained results are generally different from those waited. The major idea of this project is to change the basic paradigm by
approaching the problem by the "automatic" face rather than by that
"hydrology". The objective is to make possible the realization of a
large number of simulations at very short times (a few seconds)
allowing to take place weather forecasts by using directly the real
time meditative pluviometric data. The aim is to reach a system
where the decision-making is realized from reliable data and where
the correction of the error is permanent. A first model of control laws was realized and tested with different
return-period rainfalls. The gains obtained in rejecting volume vary
from 19 to 100 %. The development of a new algorithm was then
used to optimize calculation time and thus to overcome the
subsequent combinatorial problem in our first approach. Finally, this
new algorithm was tested with 16- year-rainfall series. The obtained
gains are 40 % of total volume rejected to the natural environment
and of 65 % in the number of discharges.
Abstract: Cole-Cole parameters of 40 post-menopausal women
are compared with their DEXA bone mineral density measurements.
Impedance characteristics of four extremities are compared; left and
right extremities are statistically same, but lower extremities are
statistically different than upper ones due to their different fat
content. The correlation of Cole-Cole impedance parameters to bone
mineral density (BMD) is observed to be higher for dominant arm.
With the post-menopausal population, ANOVA tests of the dominant
arm characteristic frequency, as a predictor for DEXA classified
osteopenic and osteoporic population around lumbar spine, is
statistically very significant. When used for total lumbar spine
osteoporosis diagnosis, the area under the Receiver Operating Curve
of the characteristic frequency is 0.830, suggesting that the Cole-Cole
plot characteristic frequency could be a useful diagnostic parameter
when integrated into standard screening methods for osteoporosis.
Moreover, the characteristic frequency can be directly measured by
monitoring frequency driven angular behavior of the dominant arm
without performing any complex calculation.
Abstract: The global demand for long-tailed macaques for
medical experimentation has continued to increase. Fulfillment of
Indonesian export demands has been mostly from natural habitats,
based on a harvesting quota. This quota has been determined
according to the total catch for a given year, and not based on
consideration of any demographic parameters or physical
environmental factors with regard to the animal; hence threatening
the sustainability of the various populations. It is therefore necessary
to formulate a method for calculating a sustainable harvesting quota,
based on population parameters in natural habitats. Considering the
possibility of variations in habitat characteristics and population
parameters, a time series observation of demographic and
physical/biotic parameters, in various habitats, was performed on 13
groups of long-tailed macaques, distributed throughout the West
Java, Lampung and Yogyakarta areas of Indonesia. These provinces
were selected for comparison of the influence of human/tourism
activities. Data on population parameters that was collected included
data on life expectancy according to age class, numbers of
individuals by sex and age class, and ‘ratio of infants to reproductive
females’. The estimation of population growth was based on a
population dynamic growth model: the Leslie matrix. The harvesting
quota was calculated as being the difference between the actual
population size and the MVP (minimum viable population) for each
sex and age class. Observation indicated that there were variations within group size
(24–106 individuals), gender (sex) ratio (1:1 to 1:1.3), life expectancy
value (0.30 to 0.93), and ‘ratio of infants to reproductive females’
(0.23 to 1.56). Results of subsequent calculations showed that
sustainable harvesting quotas for each studied group of long-tailed
macaques, ranged from 29 to 110 individuals. An estimation model
of the MVP for each age class was formulated as Log Y = 0.315 +
0.884 Log Ni (number of individual on ith age class). This study also
found that life expectancy for the juvenile age class was affected by
the humidity under tree stands, and dietary plants’ density at sapling,
pole and tree stages (equation: Y=2.296 – 1.535 RH + 0.002 Kpcg –
0.002 Ktg – 0.001 Kphn, R2 = 89.6% with a significance value of
0.001). By contrast, for the sub-adult-adult age class, life expectancy
was significantly affected by slope (equation: Y=0.377 = 0.012 Kml,
R2 = 50.4%, with significance level of 0.007). The infant-toreproductive-
female ratio was affected by humidity under tree stands,
and dietary plant density at sapling and pole stages (equation: Y = -
1.432 + 2.172 RH – 0.004 Kpcg + 0.003 Ktg, R2 = 82.0% with
significance level of 0.001). This research confirmed the importance
of population parameters in determining the minimum viable
population, and that MVP varied according to habitat characteristics
(especially food availability). It would be difficult therefore, to
formulate a general mathematical equation model for determining a
harvesting quota for the species as a whole.
Abstract: This paper discusses the propagation of sound waves in
air, specifically in narrow rectangular pathways of an occluded-ear
simulator for acoustic measurements. In narrow pathways, both the
speed of sound and the phase of the sound waves are affected by the
damping of the air viscosity. Herein, we propose a new finite-element
method (FEM) that considers the effects of the air viscosity. The
method was developed as an extension of existing FEMs for porous,
sound-absorbing materials. The results of a numerical calculation for a
three-dimensional ear-simulator model using the proposed FEM were
validated by comparing with theoretical lumped-parameter modeling
analysis and standard values.
Abstract: Standard Gibbs energy of formation ΔGfor(298.15) of
lanthanide-iron double oxides of garnet-type crystal structure
R3Fe5O12 - RIG (R – are rare earth ions) from initial oxides are
evaluated. The calculation is based on the data of standard entropies
S298.15 and standard enthalpies ΔH298.15 of formation of compounds
which are involved in the process of garnets synthesis. Gibbs energy
of formation is presented as temperature function ΔGfor(T) for the
range 300-1600K. The necessary starting thermodynamic data were
obtained from calorimetric study of heat capacity – temperature
functions and by using the semi-empirical method for calculation of
ΔH298.15 of formation. Thermodynamic functions for standard
temperature – enthalpy, entropy and Gibbs energy - are
recommended as reference data for technological evaluations.
Through the structural series of rare earth-iron garnets the correlation
between thermodynamic properties and characteristics of lanthanide
ions are elucidated.
Abstract: The objective of the study is to assess the
implementation of LED lighting into forest machine work in the dark.
In addition, the paper includes a wide variety of important and
relevant safety and health parameters. In modern, computerized work
in the cab of forest machines, artificial illumination is a demanding
task when performing duties, such as the visual inspections of wood
and computer calculations. We interviewed entrepreneurs and
gathered the following as the most pertinent themes: (1) safety, (2)
practical problems, and (3) work with LED lighting. The most
important comments were in regards to the practical problems of
LED lighting. We found indications of technical problems in
implementing LED lighting, like snow and dirt on the surfaces of
lamps that dim the emission of light. Moreover, service work in the
dark forest is dangerous and increases the risks of on-site accidents.
We also concluded that the amount of blue light to the eyes should be
assessed, especially, when the drivers are working in a semi-dark cab.
Abstract: This article presents a vibration diagnostic method
designed for Permanent Magnets (PM) electrical machines–traction
motors and generators. Those machines are commonly used in traction
drives of electrical vehicles and small wind or water systems. The
described method is very innovative and unique. Specific structural
properties of machines excited by permanent magnets are used in this
method - electromotive force (EMF) generated due to vibrations. There
was analyzed number of publications, which describe vibration
diagnostic methods, and tests of electrical machines and there was no
method found to determine the technical condition of such machine
basing on their own signals. This work presents field-circuit model,
results of static tests, results of calculations and simulations.
Abstract: The effects of flame-holder position, the ratio of flame
holder diameter to combustion chamber diameter and injection angle
on fuel propulsive droplets sizing and effective mass fraction have
been studied by a cold flow. We named the mass of fuel vapor inside
the flammability limit as the effective mass fraction. An empty
cylinder as well as a flame-holder which are a simulator for duct
combustion has been considered. The airflow comes into the cylinder
from one side and injection operation will be done by four nozzles
which are located on the entrance of cylinder. To fulfill the
calculations a modified version of KIVA-3V code which is a
transient, three-dimensional, multiphase, multi component code for
the analysis of chemically reacting flows with sprays, is used.
Abstract: This paper is focused on the reference current
calculation in the compensation mode of the active DC traction
substations. The so-called p-q theory of the instantaneous reactive
power is used as theoretical foundation. The compensation goal of
total compensation is taken into consideration for the operation under
both sinusoidal and nonsinusoidal voltage conditions, through the
two objectives of unity power factor and perfect harmonic
cancelation. Four blocks of reference current generation implement
the conceived algorithms and they are included in a specific Simulink
library, which is useful in a DSP dSPACE-based platform working
under Matlab/Simulink. The simulation results validate the
correctness of the implementation and fulfillment of the
compensation tasks.
Abstract: Greenhouses offer us suitable conditions which can
be controlled easily for the growth of the plant and they are made by
using a covering material that allows the sun light entering into the
system. Covering material can be glass, fiber glass, plastic or another
transparent element. This study investigates the solar energy usability
rates and solar energy benefitting rates of a semi-spherical (modified
arch) type greenhouse system according to different orientations and
positions which exists under climatic conditions of Bayburt. In the
concept of this study it is tried to determine the best direction and
best sizes of a semi-spherical greenhouse to get best solar benefit
from the sun. To achieve this aim a modeling study is made by using
MATLAB. However, this modeling study is run for some determined
shapes and greenhouses it can be used for different shaped
greenhouses or buildings. The basic parameters are determined as
greenhouse azimuth angle, the rate of size of long edge to short and
seasonal solar energy gaining of greenhouse. The optimum azimuth
angles of 400, 300, 250, 200, 150, 100, 50 m2 modified arch
greenhouse are 90o, 90o, 35o, 35o, 34o, 33o and 22o while their
optimum k values (ratio of length to width) are 10, 10, 10, 10, 6, 4
and 4 respectively. Positioning the buildings in order to get more
solar heat energy in winter and less in summer brings out energy and
money savings and increases the comfort.
Abstract: In this paper, the energy saving and human thermal
comfort in a typical office room are investigated. The impact of a
combined system of exhaust inlet air with light slots located at the
ceiling level in a room served by displacement ventilation system is
numerically modelled. Previous experimental data are used to
validate the Computational Fluid Dynamic (CFD) model. A case
study of simulated office room includes two seating occupants, two
computers, two data loggers and four lamps. The combined system is
located at the ceiling level above the heat sources. A new method of
calculation for the cooling coil load in Stratified Air Distribution
(STRAD) system is used in this study. The results show that 47.4%
energy saving of space cooling load can be achieved by combing the
exhaust inlet air with light slots at the ceiling level above the heat
sources.
Abstract: This article aims to analyze the static stability and
pseudostatic slope by using different methods such as: Bishop
method, Junbu, Ordinary, Morgenstern-price and GLE. The two
dimensional modeling of slope stability under various loading as: the
earthquake effect, the water level and road mobile charges. The
results show that the slope is stable in the static case without water,
but in other cases, the slope lost its stability and give unstable. The
calculation of safety factor is to evaluate the stability of the slope
using the limit equilibrium method despite the difference between the
results obtained by these methods that do not rely on the same
assumptions. In the end, the results of this study illuminate well the
influence of the action of water, moving loads and the earthquake on
the stability of the slope.
Abstract: In this paper, we propose a new method for threedimensional
object indexing based on D.A.M.C-S.H.C descriptor
(Direct and Analytical Method for Calculating the Spherical
Harmonics Coefficients). For this end, we propose a direct
calculation of the coefficients of spherical harmonics with perfect
precision. The aims of the method are to minimize, the processing
time on the 3D objects database and the searching time of similar
objects to a request object.
Firstly we start by defining the new descriptor using a new
division of 3-D object in a sphere. Then we define a new distance
which will be tested and prove his efficiency in the search for similar
objects in the database in which we have objects with very various
and important size.
Abstract: Riveting process is one of the important ways to keep
fastening the lap joints in aircraft structures. Failure of aircraft lap
joints directly depends on the stress field in the joint. An important
application of riveting process is in the construction of aircraft
fuselage structures. In this paper, a 3D finite element method is
carried out in order to optimize residual stress field in a riveted lap
joint and also to estimate its fatigue life. In continue, a number of
experiments are designed and analyzed using design of experiments
(DOE). Then, Taguchi method is used to select an optimized case
between different levels of each factor. Besides that, the factor which
affects the most on residual stress field is investigated. Such
optimized case provides the maximum residual stress field. Fatigue
life of the optimized joint is estimated by Paris-Erdogan law. Stress
intensity factors (SIFs) are calculated using both finite element
analysis and experimental formula. In addition, the effect of residual
stress field, geometry and secondary bending are considered in SIF
calculation. A good agreement is found between results of such
methods. Comparison between optimized fatigue life and fatigue life
of other joints has shown an improvement in the joint’s life.
Abstract: This paper presents an approach for the classification of
an unstructured format description for identification of file formats.
The main contribution of this work is the employment of data mining
techniques to support file format selection with just the unstructured
text description that comprises the most important format features for
a particular organisation. Subsequently, the file format indentification
method employs file format classifier and associated configurations to
support digital preservation experts with an estimation of required file
format. Our goal is to make use of a format specification knowledge
base aggregated from a different Web sources in order to select file
format for a particular institution. Using the naive Bayes method,
the decision support system recommends to an expert, the file format
for his institution. The proposed methods facilitate the selection of
file format and the quality of a digital preservation process. The
presented approach is meant to facilitate decision making for the
preservation of digital content in libraries and archives using domain
expert knowledge and specifications of file formats. To facilitate
decision-making, the aggregated information about the file formats is
presented as a file format vocabulary that comprises most common
terms that are characteristic for all researched formats. The goal is to
suggest a particular file format based on this vocabulary for analysis
by an expert. The sample file format calculation and the calculation
results including probabilities are presented in the evaluation section.
Abstract: In statistics parameter theory, usually the
parameter estimations have two kinds, one is the least-square
estimation (LSE), and the other is the best linear unbiased
estimation (BLUE). Due to the determining theorem of
minimum variance unbiased estimator (MVUE), the parameter
estimation of BLUE in linear model is most ideal. But since
the calculations are complicated or the covariance is not
given, people are hardly to get the solution. Therefore, people
prefer to use LSE rather than BLUE. And this substitution
will take some losses. To quantize the losses, many scholars
have presented many kinds of different relative efficiencies in
different views. For the linear weighted regression model, this
paper discusses the relative efficiencies of LSE of β to BLUE
of β. It also defines two new relative efficiencies and gives
their lower bounds.
Abstract: This paper presents a rank correlation curve. The
traditional correlation coefficient is valid for both continuous
variables and for integer variables using rank statistics. Since
the correlation coefficient has already been established in rank
statistics by Spearman, such a calculation can be extended to
the correlation curve.
This paper presents two survey questions. The survey
collected non-continuous variables. We will show weak to
moderate correlation. Obviously, one question has a negative
effect on the other. A review of the qualitative literature
can answer which question and why. The rank correlation
curve shows which collection of responses has a positive
slope and which collection of responses has a negative slope.
Such information is unavailable from the flat, ”first-glance”
correlation statistics.