Abstract: In Image processing the Image compression can improve
the performance of the digital systems by reducing the cost and
time in image storage and transmission without significant reduction
of the Image quality. This paper describes hardware architecture of
low complexity Discrete Cosine Transform (DCT) architecture for
image compression[6]. In this DCT architecture, common computations
are identified and shared to remove redundant computations
in DCT matrix operation. Vector processing is a method used for
implementation of DCT. This reduction in computational complexity
of 2D DCT reduces power consumption. The 2D DCT is performed
on 8x8 matrix using two 1-Dimensional Discrete cosine transform
blocks and a transposition memory [7]. Inverse discrete cosine
transform (IDCT) is performed to obtain the image matrix and
reconstruct the original image. The proposed image compression
algorithm is comprehended using MATLAB code. The VLSI design
of the architecture is implemented Using Verilog HDL. The proposed
hardware architecture for image compression employing DCT was
synthesized using RTL complier and it was mapped using 180nm
standard cells. . The Simulation is done using Modelsim. The
simulation results from MATLAB and Verilog HDL are compared.
Detailed analysis for power and area was done using RTL compiler
from CADENCE. Power consumption of DCT core is reduced to
1.027mW with minimum area[1].
Abstract: This paper describes a three-dimensional thermal
model of the current path included in the low voltage power circuit
breakers. The model can be used to analyse the thermal behaviour of
the current path during both steady-state and transient conditions.
The current path lengthwise temperature distribution and timecurrent
characteristic of the terminal connections of the power circuit
breaker have been obtained. The influence of the electric current and
voltage drop on main electric contact of the circuit breaker has been
investigated. To validate the three-dimensional thermal model, some
experimental tests have been done. There is a good correlation
between experimental and simulation results.
Abstract: An adaptive neural network controller for
autonomous underwater vehicles (AUVs) is presented in this paper.
The AUV model is highly nonlinear because of many factors, such as
hydrodynamic drag, damping, and lift forces, Coriolis and centripetal
forces, gravity and buoyancy forces, as well as forces from thruster.
In this regards, a nonlinear neural network is used to approximate the
nonlinear uncertainties of AUV dynamics, thus overcoming some
limitations of conventional controllers and ensure good performance.
The uniform ultimate boundedness of AUV tracking errors and the
stability of the proposed control system are guaranteed based on
Lyapunov theory. Numerical simulation studies for motion control of
an AUV are performed to demonstrate the effectiveness of the
proposed controller.
Abstract: In this paper the problem of estimating the time delay
between two spatially separated noisy sinusoidal signals by system
identification modeling is addressed. The system is assumed to be
perturbed by both input and output additive white Gaussian noise. The
presence of input noise introduces bias in the time delay estimates.
Normally the solution requires a priori knowledge of the input-output
noise variance ratio. We utilize the cascade of a self-tuned filter with
the time delay estimator, thus making the delay estimates robust to
input noise. Simulation results are presented to confirm the superiority
of the proposed approach at low input signal-to-noise ratios.
Abstract: The demand for higher performance graphics
continues to grow because of the incessant desire towards realism.
And, rapid advances in fabrication technology have enabled us to
build several processor cores on a single die. Hence, it is important to
develop single chip parallel architectures for such data-intensive
applications. In this paper, we propose an efficient PIM architectures
tailored for computer graphics which requires a large number of
memory accesses. We then address the two important tasks necessary
for maximally exploiting the parallelism provided by the architecture,
namely, partitioning and placement of graphic data, which affect
respectively load balances and communication costs. Under the
constraints of uniform partitioning, we develop approaches for optimal
partitioning and placement, which significantly reduce search space.
We also present heuristics for identifying near-optimal placement,
since the search space for placement is impractically large despite our
optimization. We then demonstrate the effectiveness of our partitioning
and placement approaches via analysis of example scenes; simulation
results show considerable search space reductions, and our heuristics
for placement performs close to optimal – the average ratio of
communication overheads between our heuristics and the optimal was
1.05. Our uniform partitioning showed average load-balance ratio of
1.47 for geometry processing and 1.44 for rasterization, which is
reasonable.
Abstract: We consider the problem of bandwidth allocation in a
substrate network as an optimization problem for the aggregate utility
of multiple applications with diverse requirements and describe a
simulation scheme for dynamically adaptive bandwidth allocation
protocols. The proposed simulation model based on Coloured Petri
Nets (CPN) is realized using CPN Tools.
Abstract: One of Effective parameters on the performance of linear induction motors is number of poles which must be selected and optimized to increase power efficiency and motor performance significantly. In this paper a double-sided linear induction motor with different poles number by using MAXWELL3D software is designed and with finite element method is analyzed electromagnetically. Then for dynamic simulation, linear motor by using MATLAB software is simulated. The results show that by adding poles number, system time response is increased and motor after more time reaches to steady state. Also propulsion force of motor is increased.
Abstract: Natural ventilation is an important means to improve indoor thermal comfort and reduce the energy consumption. A solar chimney system is an enhancing natural draft device, which uses solar radiation to heat the air inside the chimney, thereby converting the thermal energy into kinetic energy. The present study considered some parameters such as chimney width and solar intensity, which were believed to have a significant effect on space ventilation. Fluent CFD software was used to predict buoyant air flow and flow rates in the cavities. The results were compared with available published experimental and theoretical data from the literature. There was an acceptable trend match between the present results and the published data for the room air change per hour, ACH. Further, it was noticed that the solar intensity has a more significant effect on ACH.
Abstract: A cognitive collaborative reinforcement learning
algorithm (CCRL) that incorporates an advisor into the learning
process is developed to improve supervised learning. An autonomous
learner is enabled with a self awareness cognitive skill to decide
when to solicit instructions from the advisor. The learner can also
assess the value of advice, and accept or reject it. The method is
evaluated for robotic motion planning using simulation. Tests are
conducted for advisors with skill levels from expert to novice. The
CCRL algorithm and a combined method integrating its logic with
Clouse-s Introspection Approach, outperformed a base-line fully
autonomous learner, and demonstrated robust performance when
dealing with various advisor skill levels, learning to accept advice
received from an expert, while rejecting that of less skilled
collaborators. Although the CCRL algorithm is based on RL, it fits
other machine learning methods, since advisor-s actions are only
added to the outer layer.
Abstract: The objective of this study is to introduce estimators to the parameters and survival function for Weibull distribution using three different methods, Maximum Likelihood estimation, Standard Bayes estimation and Modified Bayes estimation. We will then compared the three methods using simulation study to find the best one base on MPE and MSE.
Abstract: The effects of dynamic subgrid scale (SGS) models are
investigated in variational multiscale (VMS) LES simulations of bluff
body flows. The spatial discretization is based on a mixed finite
element/finite volume formulation on unstructured grids. In the VMS
approach used in this work, the separation between the largest and the
smallest resolved scales is obtained through a variational projection
operator and a finite volume cell agglomeration. The dynamic version
of Smagorinsky and WALE SGS models are used to account for
the effects of the unresolved scales. In the VMS approach, these
effects are only modeled in the smallest resolved scales. The dynamic
VMS-LES approach is applied to the simulation of the flow around a
circular cylinder at Reynolds numbers 3900 and 20000 and to the flow
around a square cylinder at Reynolds numbers 22000 and 175000. It
is observed as in previous studies that the dynamic SGS procedure
has a smaller impact on the results within the VMS approach than in
LES. But improvements are demonstrated for important feature like
recirculating part of the flow. The global prediction is improved for
a small computational extra cost.
Abstract: In this paper, we consider a multi user multiple input
multiple output (MU-MIMO) based cooperative reporting system for
cognitive radio network. In the reporting network, the secondary
users forward the primary user data to the common fusion center
(FC). The FC is equipped with linear equalizers and an energy
detector to make the decision about the spectrum. The primary user
data are considered to be a digital video broadcasting - terrestrial
(DVB-T) signal. The sensing channel and the reporting channel are
assumed to be an additive white Gaussian noise and an independent
identically distributed Raleigh fading respectively. We analyzed the
detection probability of MU-MIMO system with linear equalizers and
arrived at the closed form expression for average detection
probability. Also the system performance is investigated under
various MIMO scenarios through Monte Carlo simulations.
Abstract: This paper presents a novel approach for optimal
reconfiguration of radial distribution systems. Optimal
reconfiguration involves the selection of the best set of branches to
be opened, one each from each loop, such that the resulting radial
distribution system gets the desired performance. In this paper an
algorithm is proposed based on simple heuristic rules and identified
an effective switch status configuration of distribution system for the
minimum loss reduction. This proposed algorithm consists of two
parts; one is to determine the best switching combinations in all loops
with minimum computational effort and the other is simple optimum
power loss calculation of the best switching combination found in
part one by load flows. To demonstrate the validity of the proposed
algorithm, computer simulations are carried out on 33-bus system.
The results show that the performance of the proposed method is
better than that of the other methods.
Abstract: The Norwegian Military Academy (Army) has
initiated a project with the main ambition to explore possible avenues
to enhancing operational effectiveness through an increased use of
simulation-based training and exercises. Within a cost/benefit
framework, we discuss opportunities and limitations of vertical and
horizontal integration of the existing tactical training system. Vertical
integration implies expanding the existing training system to span the
full range of training from tactical level (platoon, company) to
command and staff level (battalion, brigade). Horizontal integration
means including other domains than army tactics and staff
procedures in the training, such as military ethics, foreign languages,
leadership and decision making. We discuss each of the integration
options with respect to purpose and content of training, "best
practice" for organising and conducting simulation-based training,
and suggest how to evaluate training procedures and measure
learning outcomes. We conclude by giving guidelines towards further
explorative work and possible implementation.
Abstract: The mathematical modeling of storm surge in sea and
coastal regions such as the South China Sea (SCS) and the Gulf of
Thailand (GoT) are important to study the typhoon characteristics.
The storm surge causes an inundation at a lateral boundary exhibiting
in the coastal zones particularly in the GoT and some part of the SCS.
The model simulations in the three dimensional primitive equations
with a high resolution model are important to protect local properties
and human life from the typhoon surges. In the present study, the
mathematical modeling is used to simulate the typhoon–induced
surges in three case studies of Typhoon Linda 1997. The results
of model simulations at the tide gauge stations can describe the
characteristics of storm surges at the coastal zones.
Abstract: This paper presents the use of Legendre pseudospectral
method for the optimization of finite-thrust orbital transfer for
spacecrafts. In order to get an accurate solution, the System-s
dynamics equations were normalized through a dimensionless method.
The Legendre pseudospectral method is based on interpolating
functions on Legendre-Gauss-Lobatto (LGL) quadrature nodes. This
is used to transform the optimal control problem into a constrained
parameter optimization problem. The developed novel optimization
algorithm can be used to solve similar optimization problems of
spacecraft finite-thrust orbital transfer. The results of a numerical
simulation verified the validity of the proposed optimization method.
The simulation results reveal that pseudospectral optimization method
is a promising method for real-time trajectory optimization and
provides good accuracy and fast convergence.
Abstract: Current mode circuits like current conveyors are
getting significant attention in current analog ICs design due to their
higher band-width, greater linearity, larger dynamic range, simpler
circuitry, lower power consumption and less chip area. The second
generation current controlled conveyor (CCCII) has the advantage of
electronic adjustability over the CCII i.e. in CCCII; adjustment of the
X-terminal intrinsic resistance via a bias current is possible. The
presented approach is based on the CMOS implementation of second
generation positive (CCCII+), negative (CCCII-) and dual Output
Current Controlled Conveyor (DOCCCII) and its application as
Universal filter. All the circuits have been designed and simulated
using 65nm CMOS technology model parameters on Cadence
Virtuoso / Spectre using 1V supply voltage. Various simulations have
been carried out to verify the linearity between output and input
ports, range of operation frequency, etc. The outcomes show good
agreement between expected and experimental results.
Abstract: Commercial infrastructures intended for use as leisure
retreats such as golf and ski resorts have been extensively developed in many rural areas of Japan. However, following the burst of the economic bubble in the 1990s, several existing resorts faced tough
management decisions and some were forced to close their business.
In this study, six alternative management options for restructuring the
existing golf courses (park, cemetery, biofuel production, reforestation,
pasturing and abandonment) are examined and their environmental
and economic impacts are quantitatively assessed. In addition,
restructuring scenarios of these options and an ex-ante assessment
model are developed. The scenario analysis by Monte Carlo simulation shows a clear trade-off between GHG savings and benefit/cost (B/C) ratios, of which “Restoring Nature" scenario
absorbs the most CO2 among the four scenarios considered, but its B/C
ratio is the lowest. This study can be used to select or examine options
and scenarios of golf course management and rural environmental
management policies.
Abstract: The optical properties of InGaN/GaN laser diode based on quaternary alloys stopper and superlattice layers are numerically studied using ISE TCAD (Integrated System Engineering) simulation program. Improvements in laser optical performance have been achieved using quaternary alloy as superlattice layers in InGaN/GaN laser diodes. Lower threshold current of 18 mA and higher output power and slope efficiency of 22 mW and 1.6 W/A, respectively, at room temperature have been obtained. The laser structure with InAlGaN quaternary alloys as an electron blocking layer was found to provide better laser performance compared with the ternary AlxGa1-xN blocking layer.
Abstract: The connection between solar activity and adverse phenomena in the Earth’s environment that can affect space and ground based technologies has spurred interest in Space Weather (SW) research. A great effort has been put on the development of suitable models that can provide advanced forecast of SW events. With the progress in computational technology, it is becoming possible to develop operational large scale physics based models which can incorporate the most important physical processes and domains of the Sun-Earth system. In order to enhance our SW prediction capabilities we are developing advanced numerical tools. With operational requirements in mind, our goal is to develop a modular simulation framework of propagation of the disturbances from the Sun through interplanetary space to the Earth. Here, we report and discuss on the development of coronal field and solar wind components for a large scale MHD code. The model for these components is based on a potential field source surface model and an empirical Wang-Sheeley-Arge solar wind relation.